| Age | Commit message (Collapse) | Author |
|---|
|
While BCM5325/5365 do not support jumbo frames, they do support slightly
oversized frames, so do not error out if requesting a supported MTU for
them.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
BCM5325/BCM5365 do not support jumbo frames, so we should not report a
jumbo frame mtu for them. But they do support so called "oversized"
frames up to 1536 bytes long by default, so report an appropriate MTU.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Nicolas Pitre says:
====================
fix ti-am65-cpsw-nuss module removal
Fix issues preventing rmmod of ti-am65-cpsw-nuss from working properly.
v3:
- more patch submission minutiae
v2: https://lore.kernel.org/netdev/20241003172105.2712027-2-nico@fluxnic.net/T/
- conform to netdev patch submission customs
- address patch review trivias
v1: https://lore.kernel.org/netdev/20240927025301.1312590-2-nico@fluxnic.net/T/
====================
Link: https://patch.msgid.link/20241004041218.2809774-1-nico@fluxnic.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Usage of devm_alloc_etherdev_mqs() conflicts with
am65_cpsw_nuss_cleanup_ndev() as the same struct net_device instances
get unregistered twice. Switch to alloc_etherdev_mqs() and make sure
am65_cpsw_nuss_cleanup_ndev() unregisters and frees those net_device
instances properly.
With this, it is finally possible to rmmod the driver without oopsing
the kernel.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Roger Quadros <roger@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In am65_cpsw_nuss_remove(), move the call to am65_cpsw_unregister_devlink()
after am65_cpsw_nuss_cleanup_ndev() to avoid triggering the
WARN_ON(devlink_port->type != DEVLINK_PORT_TYPE_NOTSET) in
devl_port_unregister(). Makes it coherent with usage in
m65_cpsw_nuss_register_ndevs()'s cleanup path.
Fixes: 58356eb31d60 ("net: ti: am65-cpsw-nuss: Add devlink support")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move the tx cpu dma ring index update out of transmit loop of
airoha_dev_xmit routine in order to not start transmitting the packet
before it is fully DMA mapped (e.g. fragmented skbs).
Fixes: 23020f049327 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Reported-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241004-airoha-eth-7581-mapping-fix-v1-1-8e4279ab1812@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct
ordering") correctly fixed a problem with using devm_ but missed
removing the LED entry from the LEDs list.
This cause kernel panic on specific scenario where the port for the PHY
is torn down and up and the kmod for the PHY is removed.
On setting the port down the first time, the assosiacted LEDs are
correctly unregistered. The associated kmod for the PHY is now removed.
The kmod is now added again and the port is now put up, the associated LED
are registered again.
On putting the port down again for the second time after these step, the
LED list now have 4 elements. With the first 2 already unregistered
previously and the 2 new one registered again.
This cause a kernel panic as the first 2 element should have been
removed.
Fix this by correctly removing the element when LED is unregistered.
Reported-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Cc: stable@vger.kernel.org
Fixes: c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct ordering")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241004182759.14032-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- RFCOMM: FIX possible deadlock in rfcomm_sk_state_change
- hci_conn: Fix UAF in hci_enhanced_setup_sync
- btusb: Don't fail external suspend requests
* tag 'for-net-2024-10-04' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: btusb: Don't fail external suspend requests
Bluetooth: hci_conn: Fix UAF in hci_enhanced_setup_sync
Bluetooth: RFCOMM: FIX possible deadlock in rfcomm_sk_state_change
====================
Link: https://patch.msgid.link/20241004210124.4010321-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
adin1110_read_fifo()
If 'frame_size' is too small or if 'round_len' is an error code, it is
likely that an error code should be returned to the caller.
Actually, 'ret' is likely to be 0, so if one of these sanity checks fails,
'success' is returned.
Return -EINVAL instead.
Fixes: bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/8ff73b40f50d8fa994a454911b66adebce8da266.1727981562.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit b514c47ebf41a6536551ed28a05758036e6eca7c.
The commit describes that we don't have to sync the page when
recycling, and it tries to optimize that case. But we do need
to sync after allocation. Recycling side should be changed to
pass the right sync size instead.
Fixes: b514c47ebf41 ("net: stmmac: set PP_FLAG_DMA_SYNC_DEV only if XDP is enabled")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/20241004070846.2502e9ea@kernel.org
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/20241004142115.910876-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Accessing device registers seems to be not reliable, the chip
revision is sometimes detected wrongly (0 instead of expected 1).
Ensure that the chip reset is performed via reset GPIO and then
wait for 'Device Ready' status in HW_CFG register before doing
any register initializations.
Cc: stable@vger.kernel.org
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
[alex: reworked using read_poll_timeout()]
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20241004113655.3436296-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have recently noticed the exact same KASAN splat as in commit
6cd4a78d962b ("net: do not leave a dangling sk pointer, when socket
creation fails"). The problem is that commit did not fully address the
problem, as some pf->create implementations do not use sk_common_release
in their error paths.
For example, we can use the same reproducer as in the above commit, but
changing ping to arping. arping uses AF_PACKET socket and if packet_create
fails, it will just sk_free the allocated sk object.
While we could chase all the pf->create implementations and make sure they
NULL the freed sk object on error from the socket, we can't guarantee
future protocols will not make the same mistake.
So it is easier to just explicitly NULL the sk pointer upon return from
pf->create in __sock_create. We do know that pf->create always releases the
allocated sk object on error, so if the pointer is not NULL, it is
definitely dangling.
Fixes: 6cd4a78d962b ("net: do not leave a dangling sk pointer, when socket creation fails")
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Cc: stable@vger.kernel.org
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241003170151.69445-1-ignat@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When adding a delayed ref head, at delayed-ref.c:add_delayed_ref_head(),
if we fail to insert the qgroup record we don't error out, we ignore it.
In fact we treat it as if there was no error and there was already an
existing record - we don't distinguish between the cases where
btrfs_qgroup_trace_extent_nolock() returns 1, meaning a record already
existed and we can free the given record, and the case where it returns
a negative error value, meaning the insertion into the xarray that is
used to track records failed.
Effectively we end up ignoring that we are lacking qgroup record in the
dirty extents xarray, resulting in incorrect qgroup accounting.
Fix this by checking for errors and return them to the callers.
Fixes: 3cce39a8ca4e ("btrfs: qgroup: use xarray to track dirty extents in transaction")
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
There are reports that system cannot suspend due to running trim because
the task responsible for trimming the device isn't able to finish in
time, especially since we have a free extent discarding phase, which can
trim a lot of unallocated space. There are no limits on the trim size
(unlike the block group part).
Since trime isn't a critical call it can be interrupted at any time,
in such cases we stop the trim, report the amount of discarded bytes and
return an error.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219180
Link: https://bugzilla.suse.com/show_bug.cgi?id=1229737
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Luca Stefani <luca.stefani.ge1@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Per Qu Wenruo in case we have a very large disk, e.g. 8TiB device,
mostly empty although we will do the split according to our super block
locations, the last super block ends at 256G, we can submit a huge
discard for the range [256G, 8T), causing a large delay.
Split the space left to discard based on BTRFS_MAX_DISCARD_CHUNK_SIZE in
preparation of introduction of cancellation points to trim. The value
of the chunk size is arbitrary, it can be higher or derived from actual
device capabilities but we can't easily read that using
bio_discard_limit().
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219180
Link: https://bugzilla.suse.com/show_bug.cgi?id=1229737
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Luca Stefani <luca.stefani.ge1@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
scx_qmap and other schedulers in the SCX repo are using SCX_ENQ_WAKEUP to
tell whether ops.select_cpu() was called. This is incorrect as
ops.select_cpu() can be skipped in the wakeup path and leads to e.g.
incorrectly skipping direct dispatch for tasks that are bound to a single
CPU.
sched core has been updated to specify ENQUEUE_RQ_SELECTED if
->select_task_rq() was called. Map it to SCX_ENQ_CPU_SELECTED and update
scx_qmap to test it instead of SCX_ENQ_WAKEUP.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
Cc: Daniel Hodges <hodges.daniel.scott@gmail.com>
Cc: Changwoo Min <multics69@gmail.com>
Cc: Andrea Righi <andrea.righi@linux.dev>
Cc: Dan Schatzberg <schatzberg.dan@gmail.com>
|
|
was called
During ttwu, ->select_task_rq() can be skipped if only one CPU is allowed or
migration is disabled. sched_ext schedulers may perform operations such as
direct dispatch from ->select_task_rq() path and it is useful for them to
know whether ->select_task_rq() was skipped in the ->enqueue_task() path.
Currently, sched_ext schedulers are using ENQUEUE_WAKEUP for this purpose
and end up assuming incorrectly that ->select_task_rq() was called for tasks
that are bound to a single CPU or migration disabled.
Make select_task_rq() indicate whether ->select_task_rq() was called by
setting WF_RQ_SELECTED in *wake_flags and make ttwu_do_activate() map that
to ENQUEUE_RQ_SELECTED for ->enqueue_task().
This will be used by sched_ext to fix ->select_task_rq() skip detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
|
|
value
This will be used to allow select_task_rq() to indicate whether
->select_task_rq() was called by modifying *wake_flags.
This makes try_to_wake_up() call all functions that take wake_flags with
WF_TTWU set. Previously, only select_task_rq() was. Using the same flags is
more consistent, and, as the flag is only tested by ->select_task_rq()
implementations, it doesn't cause any behavior differences.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
|
|
interrupt-map number
The driver(drivers/irqchip/irq-ls-extirq.c) have not use standard DT
function to parser interrupt-map. So it doesn't consider '#address-size'
in parent interrupt controller, such as GIC.
When dt-binding verify interrupt-map, item data matrix is spitted at
incorrect position. So cause below warning:
arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dtb: interrupt-controller@14:
interrupt-map: [[0, 0, 1, 0, 0, 4, 1, 0], [1, 0, 1, 4, 2, 0, 1, 0], ...
is too short
Remove interrupt-map restriction to workaround this warning for
'fsl,ls1088a-extirq', 'fsl,ls2080a-extirq' and fsl,lx2160a-extirq.
Other keep the same restriction.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241007161823.811021-1-Frank.Li@nxp.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
msi-parent is standard property. Needn't ref to phandle. Add maxItems: 1
for it.
Fix below warning:
arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dtb: fsl-mc@80c000000: msi-parent:0: [16, 0] is too long
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241007153047.807723-1-Frank.Li@nxp.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Since, two suspend-resume cycles are required to enter hibernate and,
since we only need to enable idle optimizations in the first cycle
(which is pretty much equivalent to s2idle). We can check in_s0ix, to
prevent the system from entering idle optimizations before it actually
enters hibernate (from display's perspective). Also, call
dc_set_power_state() before dc_allow_idle_optimizations(), since it's
safer to do so because dc_set_power_state() writes to DMUB.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2fe79508d9c393bb9931b0037c5ecaee09a8dc39)
Cc: stable@vger.kernel.org # 6.10+
|
|
[Why]
Since the surface/stream update flags aren't cleared after applying
updates, those same updates may be applied again in a future call to
update surfaces/streams for surfaces/streams that aren't actually part
of that update (i.e. applying an update for one surface/stream can
trigger unintended programming on a different surface/stream).
For example, when an update results in a call to
program_front_end_for_ctx, that function may call program_pipe on all
pipes. If there are surface update flags that were never cleared on the
surface some pipe is attached to, then the same update will be
programmed again.
[How]
Clear the surface and stream update flags after applying the updates.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3441
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3616
Cc: Melissa Wen <mwen@igalia.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7671f62c10f2a4c77d89b39fd50fab7f918d6809)
Cc: stable@vger.kernel.org
|
|
Partially revert
commit 0ca9f757a0e2 ("drm/amd/pm: powerplay: Add `__counted_by` attribute for flexible arrays")
The count attribute for these arrays does not get set until
after the arrays are allocated and populated leading to false
UBSAN warnings.
Fixes: 0ca9f757a0e2 ("drm/amd/pm: powerplay: Add `__counted_by` attribute for flexible arrays")
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3662
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8a5ae927b653b43623e55610d2215ee94c027e8c)
Cc: stable@vger.kernel.org
|
|
The patch is to solve null dereference in 'aux.dev', which is
introduced in recent radeon rework. By having 'late_register',
the connector should be registered after 'drm_dev_register'
automatically, where in before it is the opposite.
Fixes: 90985660ba48 ("drm/radeon: remove load callback from kms_driver")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3665
Tested-by: Hans de Goede <hdegoede@redhat.com>
Suggested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Wu Hoi Pok <wuhoipok@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit b4c1ad70e279bacbc772a468033bdecce2f5e0dc)
|
|
Only creating a new reference for each process instead of each VM.
Fixes: 9a1c1339abf9 ("drm/amdkfd: Run restore_workers on freezable WQs")
Suggested-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5fa436289483ae56427b0896c31f72361223c758)
Cc: stable@vger.kernel.org
|
|
Pull virtio fixes from Michael Tsirkin:
"Several small bugfixes all over the place.
Most notably, fixes the vsock allocation with GFP_KERNEL in atomic
context, which has been triggering warnings for lots of testers"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost/scsi: null-ptr-dereference in vhost_scsi_get_req()
vsock/virtio: use GFP_ATOMIC under RCU read lock
virtio_console: fix misc probe bugs
virtio_ring: tag event_triggered as racy for KCSAN
vdpa/octeon_ep: Fix format specifier for pointers in debug messages
|
|
The processor_thermal driver uses pcim_device_enable() to enable a PCI
device, which means the device will be automatically disabled on driver
detach. Thus there is no need to call pci_disable_device() again on it.
With recent PCI device resource management improvements, e.g. commit
f748a07a0b64 ("PCI: Remove legacy pcim_release()"), this problem is
exposed and triggers the warining below.
[ 224.010735] proc_thermal_pci 0000:00:04.0: disabling already-disabled device
[ 224.010747] WARNING: CPU: 8 PID: 4442 at drivers/pci/pci.c:2250 pci_disable_device+0xe5/0x100
...
[ 224.010844] Call Trace:
[ 224.010845] <TASK>
[ 224.010847] ? show_regs+0x6d/0x80
[ 224.010851] ? __warn+0x8c/0x140
[ 224.010854] ? pci_disable_device+0xe5/0x100
[ 224.010856] ? report_bug+0x1c9/0x1e0
[ 224.010859] ? handle_bug+0x46/0x80
[ 224.010862] ? exc_invalid_op+0x1d/0x80
[ 224.010863] ? asm_exc_invalid_op+0x1f/0x30
[ 224.010867] ? pci_disable_device+0xe5/0x100
[ 224.010869] ? pci_disable_device+0xe5/0x100
[ 224.010871] ? kfree+0x21a/0x2b0
[ 224.010873] pcim_disable_device+0x20/0x30
[ 224.010875] devm_action_release+0x16/0x20
[ 224.010878] release_nodes+0x47/0xc0
[ 224.010880] devres_release_all+0x9f/0xe0
[ 224.010883] device_unbind_cleanup+0x12/0x80
[ 224.010885] device_release_driver_internal+0x1ca/0x210
[ 224.010887] driver_detach+0x4e/0xa0
[ 224.010889] bus_remove_driver+0x6f/0xf0
[ 224.010890] driver_unregister+0x35/0x60
[ 224.010892] pci_unregister_driver+0x44/0x90
[ 224.010894] proc_thermal_pci_driver_exit+0x14/0x5f0 [processor_thermal_device_pci]
...
[ 224.010921] ---[ end trace 0000000000000000 ]---
Remove the excess pci_disable_device() calls.
Fixes: acd65d5d1cf4 ("thermal/drivers/int340x/processor_thermal: Add PCI MMIO based thermal driver")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240930081801.28502-3-rui.zhang@intel.com
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The TPMI_RAPL_REG_DOMAIN_INFO value needs to be multiplied by 8 to get
the register offset.
Cc: All applicable <stable@vger.kernel.org>
Fixes: 903eb9fb85e3 ("powercap: intel_rapl_tpmi: Fix System Domain probing")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://patch.msgid.link/20240930081801.28502-2-rui.zhang@intel.com
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Asus Vivobook Pro 15 OLED comes in 3 N6506M* models:
N6506MU: Intel Ultra 9 185H, 3K OLED, RTX4060
N6506MV: Intel Ultra 7 155H, 3K OLED, RTX4050
N6506MJ: Intel Ultra 7 155H, FHD OLED, RTX3050
Fold the 3 DMI quirks for these into a single quirk to reduce the number
of quirks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241005212819.354681-5-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Asus has 2 ExpertBook B1402C models:
B1402CBA with 12th gen Intel CPUs
B1402CVA with 13th gen Intel CPUs
Fold the 2 DMI quirks for these into a single quirk to reduce the number
of quirks.
Likewise Asus has 3 ExpertBook B1502C models:
B1502CBA with 12th gen Intel CPUs
B1502CGA with 12th gen Intel N-series CPUs
B1502CVA with 13th gen Intel CPUs
Fold the 3 DMI quirks for these into a single quirk to reduce the number
of quirks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241005212819.354681-4-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Like the various 14" Asus ExpertBook B2 B2402* models there are also
4 variants of the 15" Asus ExpertBook B2 B2502* models:
B2502CBA: 12th gen Intel CPU, non flip
B2502FBA: 12th gen Intel CPU, flip
B2502CVA: 13th gen Intel CPU, non flip
B2502FVA: 13th gen Intel CPU, flip
Currently there already are DMI quirks for the B2502CBA, B2502FBA and
B2502CVA models. Asus website shows that there also is a B2502FVA.
Rather then adding a 4th quirk fold the 3 existing quirks into a single
quirk covering B2502* to also cover the last model while at the same time
reducing the number of quirks.
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241005212819.354681-3-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The Asus ExpertBook B2402CBA / B2402FBA are the non flip / flip versions
of the 14" Asus ExpertBook B2 with 12th gen Intel processors.
It has been reported that the B2402FVA which is the 14" Asus ExpertBook
B2 flip with 13th gen Intel processors needs to skip the IRQ override too.
And looking at Asus website there also is a B2402CVA which is the non flip
model with 13th gen Intel processors.
Summarizing the following 4 models of the Asus ExpertBook B2 are known:
B2402CBA: 12th gen Intel CPU, non flip
B2402FBA: 12th gen Intel CPU, flip
B2402CVA: 13th gen Intel CPU, non flip
B2402FVA: 13th gen Intel CPU, flip
Fold the 2 existing quirks for the B2402CBA and B2402FBA into a single
quirk covering B2402* to also cover the 2 other models while at the same
time reducing the number of quirks.
Reported-by: Stefan Blum <stefan.blum@gmail.com>
Closes: https://lore.kernel.org/platform-driver-x86/a983e6d5-c7ab-4758-be9b-7dcfc1b44ed3@gmail.com/
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241005212819.354681-2-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since commit 3f8ca2e115e5 ("vhost/scsi: Extract common handling code
from control queue handler") a null pointer dereference bug can be
triggered when guest sends an SCSI AN request.
In vhost_scsi_ctl_handle_vq(), `vc.target` is assigned with
`&v_req.tmf.lun[1]` within a switch-case block and is then passed to
vhost_scsi_get_req() which extracts `vc->req` and `tpg`. However, for
a `VIRTIO_SCSI_T_AN_*` request, tpg is not required, so `vc.target` is
set to NULL in this branch. Later, in vhost_scsi_get_req(),
`vc->target` is dereferenced without being checked, leading to a null
pointer dereference bug. This bug can be triggered from guest.
When this bug occurs, the vhost_worker process is killed while holding
`vq->mutex` and the corresponding tpg will remain occupied
indefinitely.
Below is the KASAN report:
Oops: general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 1 PID: 840 Comm: poc Not tainted 6.10.0+ #1
Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS
1.16.3-debian-1.16.3-2 04/01/2014
RIP: 0010:vhost_scsi_get_req+0x165/0x3a0
Code: 00 fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 2b 02 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 65 30 4c 89 e2 48 c1 ea 03 <0f> b6
04 02 4c 89 e2 83 e2 07 38 d0 7f 08 84 c0 0f 85 be 01 00 00
RSP: 0018:ffff888017affb50 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff88801b000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff888017affcb8
RBP: ffff888017affb80 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff888017affc88 R14: ffff888017affd1c R15: ffff888017993000
FS: 000055556e076500(0000) GS:ffff88806b100000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000200027c0 CR3: 0000000010ed0004 CR4: 0000000000370ef0
Call Trace:
<TASK>
? show_regs+0x86/0xa0
? die_addr+0x4b/0xd0
? exc_general_protection+0x163/0x260
? asm_exc_general_protection+0x27/0x30
? vhost_scsi_get_req+0x165/0x3a0
vhost_scsi_ctl_handle_vq+0x2a4/0xca0
? __pfx_vhost_scsi_ctl_handle_vq+0x10/0x10
? __switch_to+0x721/0xeb0
? __schedule+0xda5/0x5710
? __kasan_check_write+0x14/0x30
? _raw_spin_lock+0x82/0xf0
vhost_scsi_ctl_handle_kick+0x52/0x90
vhost_run_work_list+0x134/0x1b0
vhost_task_fn+0x121/0x350
...
</TASK>
---[ end trace 0000000000000000 ]---
Let's add a check in vhost_scsi_get_req.
Fixes: 3f8ca2e115e5 ("vhost/scsi: Extract common handling code from control queue handler")
Signed-off-by: Haoran Zhang <wh1sper@zju.edu.cn>
[whitespace fixes]
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <b26d7ddd-b098-4361-88f8-17ca7f90adf7@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
virtio_transport_send_pkt in now called on transport fast path,
under RCU read lock. In that case, we have a bug: virtio_add_sgs
is called with GFP_KERNEL, and might sleep.
Pass the gfp flags as an argument, and use GFP_ATOMIC on
the fast path.
Link: https://lore.kernel.org/all/hfcr2aget2zojmqpr4uhlzvnep4vgskblx5b6xf2ddosbsrke7@nt34bxgp7j2x
Fixes: efcd71af38be ("vsock/virtio: avoid queuing packets when intermediate queue is empty")
Reported-by: Christian Brauner <brauner@kernel.org>
Cc: Stefano Garzarella <sgarzare@redhat.com>
Cc: Luigi Leonardi <luigi.leonardi@outlook.com>
Message-ID: <3fbfb6e871f625f89eb578c7228e127437b1975a.1727876449.git.mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@amd.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Luigi Leonardi <luigi.leonardi@outlook.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
|
|
This driver requires REGMAP_I2C to be selected in order to get access to
regmap_config, regmap_bus, and devm_regmap_init_i2c.
Add the missing dependency.
Fixes: 021730acbca6 ("hwmon: (max1668) Convert to use regmap")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20241002-hwmon-select-regmap-v1-4-548d03268934@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver requires REGMAP_I2C to be selected in order to get access to
regmap_config and devm_regmap_init_i2c. Add the missing dependency.
Fixes: 2b9ea4262ae9 ("hwmon: Add driver for ltc2991")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20241002-hwmon-select-regmap-v1-3-548d03268934@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver requires REGMAP_I2C to be selected in order to get access to
regmap_config and devm_regmap_init_i2c. Add the missing dependency.
Fixes: ef67959c4253 ("hwmon: (adt7470) Convert to use regmap")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20241002-hwmon-select-regmap-v1-2-548d03268934@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver requires REGMAP_I2C to be selected in order to get access to
regmap_config and devm_regmap_init_i2c. Add the missing dependency.
Fixes: df885d912f67 ("hwmon: (adm9240) Convert to regmap")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20241002-hwmon-select-regmap-v1-1-548d03268934@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver requires REGMAP_I2C to be selected in order to get access to
regmap_config and devm_regmap_init_i2c. Add the missing dependency.
Fixes: 07830d9ab34c ("hwmon: add initial NXP MC34VR500 PMIC monitoring support")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20241002-mc34vr500-select-regmap_i2c-v1-1-a01875d0a2e5@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
0-day reports:
drivers/hwmon/tmp513.c:162:21: error:
variable 'tmp51x_regmap_config' has initializer but incomplete type
162 | static const struct regmap_config tmp51x_regmap_config = {
| ^
struct regmap_config is only available if REGMAP is enabled.
Add the missing Kconfig dependency to fix the problem.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410020246.2cTDDx0X-lkp@intel.com/
Fixes: 59dfa75e5d82 ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.")
Cc: Eric Tremblay <etremblay@distech-controls.com>
Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The device_for_each_child_node() loop requires calls to
fwnode_handle_put() upon early returns to decrement the refcount of
the child node and avoid leaking memory.
There are multiple early returns within that loop in
adt7475_fan_pwm_config(), but fwnode_handle_put() is never called.
Instead of adding the missing calls, the scoped version of the loop can
be used to simplify the code and avoid mistakes in the future if new
early returns are added.
This issue was recently introduced and it does not affect old kernels
that do not support the scoped variant.
Fixes: 777c97ff08d0 ("hwmon: (adt7475) Add support for configuring initial PWM state")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Message-ID: <20240926-hwmon_adt7475_memleak-v1-1-89b8ee07507a@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Consistently use CVL instead of Columbiaville, since CVL is already
being used in all other sensor labels for the Intel N6000 card.
Fixes: e1983220ae14 ("hwmon: intel-m10-bmc-hwmon: Add N6000 sensors")
Signed-off-by: Peter Colberg <peter.colberg@intel.com>
Reviewed-by: Michael Adler <michael.adler@intel.com>
Message-ID: <20240919173417.867640-1-peter.colberg@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Upon closing the file descriptor, the active performance monitor is not
stopped. Although all perfmons are destroyed in `vc4_perfmon_close_file()`,
the active performance monitor's pointer (`vc4->active_perfmon`) is still
retained.
If we open a new file descriptor and submit a few jobs with performance
monitors, the driver will attempt to stop the active performance monitor
using the stale pointer in `vc4->active_perfmon`. However, this pointer
is no longer valid because the previous process has already terminated,
and all performance monitors associated with it have been destroyed and
freed.
To fix this, when the active performance monitor belongs to a given
process, explicitly stop it before destroying and freeing it.
Cc: stable@vger.kernel.org # v4.17+
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Juan A. Suarez Romero <jasuarez@igalia.com>
Fixes: 65101d8c9108 ("drm/vc4: Expose performance counters to userspace")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Juan A. Suarez <jasuarez@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241004123817.890016-2-mcanal@igalia.com
|
|
When running `kmscube` with one or more performance monitors enabled
via `GALLIUM_HUD`, the following kernel panic can occur:
[ 55.008324] Unable to handle kernel paging request at virtual address 00000000052004a4
[ 55.008368] Mem abort info:
[ 55.008377] ESR = 0x0000000096000005
[ 55.008387] EC = 0x25: DABT (current EL), IL = 32 bits
[ 55.008402] SET = 0, FnV = 0
[ 55.008412] EA = 0, S1PTW = 0
[ 55.008421] FSC = 0x05: level 1 translation fault
[ 55.008434] Data abort info:
[ 55.008442] ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000
[ 55.008455] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 55.008467] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 55.008481] user pgtable: 4k pages, 39-bit VAs, pgdp=00000001046c6000
[ 55.008497] [00000000052004a4] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
[ 55.008525] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP
[ 55.008542] Modules linked in: rfcomm [...] vc4 v3d snd_soc_hdmi_codec drm_display_helper
gpu_sched drm_shmem_helper cec drm_dma_helper drm_kms_helper i2c_brcmstb
drm drm_panel_orientation_quirks snd_soc_core snd_compress snd_pcm_dmaengine snd_pcm snd_timer snd backlight
[ 55.008799] CPU: 2 PID: 166 Comm: v3d_bin Tainted: G C 6.6.47+rpt-rpi-v8 #1 Debian 1:6.6.47-1+rpt1
[ 55.008824] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[ 55.008838] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 55.008855] pc : __mutex_lock.constprop.0+0x90/0x608
[ 55.008879] lr : __mutex_lock.constprop.0+0x58/0x608
[ 55.008895] sp : ffffffc080673cf0
[ 55.008904] x29: ffffffc080673cf0 x28: 0000000000000000 x27: ffffff8106188a28
[ 55.008926] x26: ffffff8101e78040 x25: ffffff8101baa6c0 x24: ffffffd9d989f148
[ 55.008947] x23: ffffffda1c2a4008 x22: 0000000000000002 x21: ffffffc080673d38
[ 55.008968] x20: ffffff8101238000 x19: ffffff8104f83188 x18: 0000000000000000
[ 55.008988] x17: 0000000000000000 x16: ffffffda1bd04d18 x15: 00000055bb08bc90
[ 55.009715] x14: 0000000000000000 x13: 0000000000000000 x12: ffffffda1bd4cbb0
[ 55.010433] x11: 00000000fa83b2da x10: 0000000000001a40 x9 : ffffffda1bd04d04
[ 55.011162] x8 : ffffff8102097b80 x7 : 0000000000000000 x6 : 00000000030a5857
[ 55.011880] x5 : 00ffffffffffffff x4 : 0300000005200470 x3 : 0300000005200470
[ 55.012598] x2 : ffffff8101238000 x1 : 0000000000000021 x0 : 0300000005200470
[ 55.013292] Call trace:
[ 55.013959] __mutex_lock.constprop.0+0x90/0x608
[ 55.014646] __mutex_lock_slowpath+0x1c/0x30
[ 55.015317] mutex_lock+0x50/0x68
[ 55.015961] v3d_perfmon_stop+0x40/0xe0 [v3d]
[ 55.016627] v3d_bin_job_run+0x10c/0x2d8 [v3d]
[ 55.017282] drm_sched_main+0x178/0x3f8 [gpu_sched]
[ 55.017921] kthread+0x11c/0x128
[ 55.018554] ret_from_fork+0x10/0x20
[ 55.019168] Code: f9400260 f1001c1f 54001ea9 927df000 (b9403401)
[ 55.019776] ---[ end trace 0000000000000000 ]---
[ 55.020411] note: v3d_bin[166] exited with preempt_count 1
This issue arises because, upon closing the file descriptor (which happens
when we interrupt `kmscube`), the active performance monitor is not
stopped. Although all perfmons are destroyed in `v3d_perfmon_close_file()`,
the active performance monitor's pointer (`v3d->active_perfmon`) is still
retained.
If `kmscube` is run again, the driver will attempt to stop the active
performance monitor using the stale pointer in `v3d->active_perfmon`.
However, this pointer is no longer valid because the previous process has
already terminated, and all performance monitors associated with it have
been destroyed and freed.
To fix this, when the active performance monitor belongs to a given
process, explicitly stop it before destroying and freeing it.
Cc: stable@vger.kernel.org # v5.15+
Closes: https://github.com/raspberrypi/linux/issues/6389
Fixes: 26a4dc29b74a ("drm/v3d: Expose performance counters to userspace")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Juan A. Suarez <jasuarez@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241004130625.918580-2-mcanal@igalia.com
|
|
This prevented the compiler from catching the patch
that broke the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20241007094004.242122-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 86b20af11e84c26ae3fde4dcc4f490948e3f8035.
This patch leads to passing 0 to simple_read_from_buffer()
as a fifth argument, turning the read method into a nop.
The change is fundamentally flawed, as it breaks the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20241007094004.242122-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The background blockgc scanner runs on a 5m interval by default and
trims preallocation (post-eof and cow fork) from inodes that are
otherwise idle. Idle effectively means that iolock can be acquired
without blocking and that the inode has no dirty pagecache or I/O in
flight.
This simple mechanism and heuristic has worked fairly well for
post-eof speculative preallocations. Support for reflink and COW
fork preallocations came sometime later and plugged into the same
mechanism, with similar heuristics. Some recent testing has shown
that COW fork preallocation may be notably more sensitive to blockgc
processing than post-eof preallocation, however.
For example, consider an 8GB reflinked file with a COW extent size
hint of 1MB. A worst case fully randomized overwrite of this file
results in ~8k extents of an average size of ~1MB. If the same
workload is interrupted a couple times for blockgc processing
(assuming the file goes idle), the resulting extent count explodes
to over 100k extents with an average size <100kB. This is
significantly worse than ideal and essentially defeats the COW
extent size hint mechanism.
While this particular test is instrumented, it reflects a fairly
reasonable pattern in practice where random I/Os might spread out
over a large period of time with varying periods of (in)activity.
For example, consider a cloned disk image file for a VM or container
with long uptime and variable and bursty usage. A background blockgc
scan that races and processes the image file when it happens to be
clean and idle can have a significant effect on the future
fragmentation level of the file, even when still in use.
To help combat this, update the heuristic to skip cowblocks inodes
that are currently opened for write access during non-sync blockgc
scans. This allows COW fork preallocations to persist for as long as
possible unless otherwise needed for functional purposes (i.e. a
sync scan), the file is idle and closed, or the inode is being
evicted from cache. While here, update the comments to help
distinguish performance oriented heuristics from the logic that
exists to maintain functional correctness.
Suggested-by: Darrick Wong <djwong@kernel.org>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
Currently the debug-only xfs_bmap_exact_minlen_extent_alloc allocation
variant fails to drop into the lowmode last resort allocator, and
thus can sometimes fail allocations for which the caller has a
transaction block reservation.
Fix this by using xfs_bmap_btalloc_low_space to do the actual allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
