| Age | Commit message (Collapse) | Author |
|---|
|
_badblocks_set() returns success if at least one badblock is set
successfully, even if others fail. This can lead to data inconsistencies
in raid, where a failed badblock set should trigger the disk to be kicked
out to prevent future reads from failed write areas.
_badblocks_set() should return error if any badblock set fails. Instead
of relying on 'rv', directly returning 'sectors' for clearer logic. If all
badblocks are successfully set, 'sectors' will be 0, otherwise it
indicates the number of badblocks that have not been set yet, thus
signaling failure.
By the way, it can also fix an issue: when a newly set unack badblock is
included in an existing ack badblock, the setting will return an error.
···
echo "0 100" /sys/block/md0/md/dev-loop1/bad_blocks
echo "0 100" /sys/block/md0/md/dev-loop1/unacknowledged_bad_blocks
-bash: echo: write error: No space left on device
```
After fix, it will return success.
Fixes: aa511ff8218b ("badblocks: switch to the improved badblock handling code")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Coly Li <colyli@kernel.org>
Link: https://lore.kernel.org/r/20250227075507.151331-6-zhengqixing@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In the current handling of badblocks settings, a lot of processing has
been done for scenarios where the number of badblocks exceeds 512.
This makes the code look quite complex and also introduces some issues,
For example, if there is 512 badblocks already:
for((i=0; i<510; i++)); do ((sector=i*2)); echo "$sector 1" > bad_blocks; done
echo 2100 10 > bad_blocks
echo 2200 10 > bad_blocks
Set new one, exceed 512:
echo 2000 500 > bad_blocks
Expected:
2000 500
Actual:
2100 400
In fact, a disk shouldn't have too many badblocks, and for disks with
512 badblocks, attempting to set more bad blocks doesn't make much sense.
At that point, the more appropriate action would be to replace the disk.
Therefore, to resolve these issues and simplify the code somewhat, return
error directly when setting badblocks exceeds 512.
Fixes: aa511ff8218b ("badblocks: switch to the improved badblock handling code")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20250227075507.151331-5-zhengqixing@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If ack and unack badblocks are adjacent, they will not be merged and will
remain as two separate badblocks. Even after the bad blocks are written
to disk and both become ack, they will still remain as two independent
bad blocks. This is not ideal as it wastes the limited space for
badblocks. Therefore, during ack_all_badblocks(), attempt to merge
badblocks if they are adjacent.
Fixes: aa511ff8218b ("badblocks: switch to the improved badblock handling code")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Coly Li <colyli@kernel.org>
Link: https://lore.kernel.org/r/20250227075507.151331-4-zhengqixing@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Factor out try_adjacent_combine(), and it will be used in the later patch.
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20250227075507.151331-3-zhengqixing@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
'bb->shift' is used directly in badblocks. It is wrong, fix it.
Fixes: 3ea3354cb9f0 ("badblocks: improve badblocks_check() for multiple ranges handling")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Coly Li <colyli@kernel.org>
Link: https://lore.kernel.org/r/20250227075507.151331-2-zhengqixing@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently, BLK_INTEGRITY_NOGENERATE and BLK_INTEGRITY_NOVERIFY are not
explicitly set during integrity initialization. This can lead to
incorrect reporting of read_verify and write_generate sysfs values,
particularly when a device does not support integrity. Ensure that these
flags are correctly initialized by default.
Reported-by: M Nikhil <nikh1092@linux.ibm.com>
Link: https://lore.kernel.org/linux-block/f6130475-3ccd-45d2-abde-3ccceada0f0a@linux.ibm.com/
Fixes: 9f4aa46f2a74 ("block: invert the BLK_INTEGRITY_{GENERATE,VERIFY} flags")
Signed-off-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250305063033.1813-3-anuj20.g@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
queue_limits_stack_integrity() incorrectly sets
BLK_INTEGRITY_DEVICE_CAPABLE for a DM device even when none of its
underlying devices support integrity. This happens because the flag is
inherited unconditionally. Ensure that integrity capabilities are
correctly propagated only when the underlying devices actually support
integrity.
Reported-by: M Nikhil <nikh1092@linux.ibm.com>
Link: https://lore.kernel.org/linux-block/f6130475-3ccd-45d2-abde-3ccceada0f0a@linux.ibm.com/
Fixes: c6e56cf6b2e7 ("block: move integrity information into queue_limits")
Signed-off-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250305063033.1813-2-anuj20.g@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Now ->carryover_bytes[] and ->carryover_ios[] only covers limit/config
update.
Actually the carryover bytes/ios can be carried to ->bytes_disp[] and
->io_disp[] directly, since the carryover is one-shot thing and only valid
in current slice.
Then we can remove the two fields and simplify code much.
Type of ->bytes_disp[] and ->io_disp[] has to change as signed because the
two fields may become negative when updating limits or config, but both are
big enough for holding bytes/ios dispatched in single slice
Cc: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20250305043123.3938491-4-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 29390bb5661d ("blk-throttle: support prioritized processing of metadata")
takes bytes/ios carryover for prioritized processing of metadata. Turns out
we can support it by charging it directly without trimming slice, and the
result is same with carryover.
Cc: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20250305043123.3938491-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The two fields are not used any more, so remove them.
Cc: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20250305043123.3938491-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The bio submission time may be a few jiffies more than the expected
waiting time, due to 'extra_bytes' can't be divided in
tg_within_bps_limit(), and also due to timer wakeup delay.
In this case, adjust slice_start to jiffies will discard the extra wait time,
causing lower rate than expected.
Current in-tree code already covers deviation by rounddown(), but turns
out it is not enough, because jiffies - slice_start can be a multiple of
throtl_slice.
For example, assume bps_limit is 1000bytes, 1 jiffes is 10ms, and
slice is 20ms(2 jiffies), expected rate is 1000 / 1000 * 20 = 20 bytes
per slice.
If user issues two 21 bytes IO, then wait time will be 30ms for the
first IO:
bytes_allowed = 20, extra_bytes = 1;
jiffy_wait = 1 + 2 = 3 jiffies
and consider
extra 1 jiffies by timer, throtl_trim_slice() will be called at:
jiffies = 40ms
slice_start = 0ms, slice_end= 40ms
bytes_disp = 21
In this case, before the patch, real rate in the first two slices is
10.5 bytes per slice, and slice will be updated to:
jiffies = 40ms
slice_start = 40ms, slice_end = 60ms,
bytes_disp = 0;
Hence the second IO will have to wait another 30ms;
With the patch, the real rate in the first slice is 20 bytes per slice,
which is the same as expected, and slice will be updated:
jiffies=40ms,
slice_start = 20ms, slice_end = 60ms,
bytes_disp = 1;
And now, there is still 19 bytes allowed in the second slice, and the
second IO will only have to wait 10ms;
This problem will cause blktests throtl/001 failure in case of
CONFIG_HZ_100=y, fix it by preserving one extra finished slice in
throtl_trim_slice().
Fixes: e43473b7f223 ("blkio: Core implementation of throttle policy")
Reported-by: Ming Lei <ming.lei@redhat.com>
Closes: https://lore.kernel.org/linux-block/20250222092823.210318-3-yukuai1@huaweicloud.com/
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20250227120645.812815-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 403ebc877832 ("ublk_drv: add module parameter of ublks_max for
limiting max allowed ublk dev"), claimed ublks_max was added to prevent
a DoS situation with an untrusted user creating too many ublk devices.
If that's the case, ublks_max should only restrict the number of
unprivileged ublk devices in the system. Enforce the limit only for
unprivileged ublk devices, and rename variables accordingly. Leave the
external-facing parameter name unchanged, since changing it may break
systems which use it (but still update its documentation to reflect its
new meaning).
As a result of this change, in a system where there are only normal
(non-unprivileged) devices, the maximum number of such devices is
increased to 1 << MINORBITS, or 1048576. That ought to be enough for
anyone, right?
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250228-ublks_max-v1-1-04b7379190c0@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The struct is introduced in the commit 754d96798fab
("loop: remove loop.h"), but it is not used now.
So remove it.
No functional changes.
Signed-off-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250227163343.55952-1-yanjun.zhu@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The in-tree ublk driver doesn't need DMA alignment limit because there
is one data copy between request pages and the userspace buffer.
However, ublk is going to support zero copy, then DMA alignment limit
is required, because same IO buffer is forwarded to backend which may
have specific buffer DMA alignment limit, so the limit has to be exposed
from the frontend driver to client application.
Cc: Keith Busch <kbusch@kernel.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250227103707.2640014-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Many of the fields in struct bio_integrity_payload are only needed for
the default integrity buffer in the block layer, and the variable
sized array at the end of the structure makes it very hard to embed
into caller allocated structures.
Reduce struct bio_integrity_payload to the minimal structure needed in
common code and create two separate containing structures for the
automatically generated payload and the caller allocated payload.
The latter is a simple wrapper for struct bio_integrity_payload and
the bvecs, while the former contains the additional fields moved out
of struct bio_integrity_payload.
Always use a dedicated mempool for automatic integrity metadata
instead of depending on bio_set that is submitter controlled and thus
often doesn't have the mempool initialized and stop using mempools for
the submitter buffers as they aren't in the NOIO I/O submission path
where we need to guarantee forward progress.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Link: https://lore.kernel.org/r/20250225154449.422989-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The code that automatically creates a integrity payload and generates and
verifies the checksums for bios that don't have submitter-provided
integrity payload currently sits right in the middle of the block
integrity metadata infrastructure. Split it into a separate file to
make the different layers clear.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20250225154449.422989-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
None of the few drivers still using the legacy block layer bounce
buffering support integrity metadata. Explicitly mark the features as
incompatible and stop creating the slab and mempool for integrity
buffers for the bounce bio_set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20250225154449.422989-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The current null_blk implementation checks if any bad blocks exist in
the target blocks of each IO. If so, the IO fails and data is not
transferred for all of the IO target blocks. However, when real storage
devices have bad blocks, the devices may transfer data partially up to
the first bad blocks (e.g., SAS drives). Especially, when the IO is a
write operation, such partial IO leaves partially written data on the
device.
To simulate such partial IO using null_blk, introduce the new parameter
'badblocks_partial_io'. When this parameter is set,
null_handle_badblocks() returns the number of the sectors for the
partial IO as its third pointer argument. Pass the returned number of
sectors to the following calls to null_handle_memory_backend() in
null_process_cmd() and null_zone_write().
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20250226100613.1622564-6-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
As preparation to support partial data transfer, add a new argument to
null_handle_rq() to pass the number of sectors to transfer. While at it,
rename the function from null_handle_rq to null_handle_data_transfer.
This commit does not change the behavior.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20250226100613.1622564-5-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
As a preparation to support partial data transfer due to badblocks,
replace the null_process_cmd() call in null_zone_write() with equivalent
calls to null_handle_badblocks() and null_handle_memory_backed(). This
commit does not change behavior. It will enable null_handle_badblocks()
to return the size of partial data transfer in the following commit,
allowing null_zone_write() to move write pointers appropriately.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20250226100613.1622564-4-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When IO errors happen on real storage devices, the IOs repeated to the
same target range can success by virtue of recovery features by devices,
such as reserved block assignment. To simulate such IO errors and
recoveries, introduce the new parameter badblocks_once parameter. When
this parameter is set to 1, the specified badblocks are cleared after
the first IO error, so that the next IO to the blocks succeed.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20250226100613.1622564-3-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The null_blk configfs file 'features' provides a string that lists
available null_blk features for userspace programs to reference.
The string is defined as a long constant in the code, which tends to be
forgotten for updates. It also causes checkpatch.pl to report
"WARNING: quoted string split across lines".
To avoid these drawbacks, generate the feature string on the fly. Refer
to the ca_name field of each element in the nullb_device_attrs table and
concatenate them in the given buffer. Also, sorted nullb_device_attrs
table elements in alphabetical order.
Of note is that the feature "index" was missing before this commit.
This commit adds it to the generated string.
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20250226100613.1622564-2-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In case of an error, ublk's ->uring_cmd() functions currently return
-EIOCBQUEUED and immediately call io_uring_cmd_done(). -EIOCBQUEUED and
io_uring_cmd_done() are intended for asynchronous completions. For
synchronous completions, the ->uring_cmd() function can just return the
negative return code directly. This skips io_uring_cmd_del_cancelable(),
and deferring the completion to task work. So return the error code
directly from __ublk_ch_uring_cmd() and ublk_ctrl_uring_cmd().
Update ublk_ch_uring_cmd_cb(), which currently ignores the return value
from __ublk_ch_uring_cmd(), to call io_uring_cmd_done() for synchronous
completions.
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20250225212456.2902549-1-csander@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The original comment contains a grammatical error. Rewrite it into a more
easily understandable sentence.
Signed-off-by: Tang Yizhou <yizhou.tang@shopee.com>
Link: https://lore.kernel.org/r/20250213100611.209997-3-yizhou.tang@shopee.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
wbt_wait() no longer uses a spinlock as a parameter. Update the function
comments accordingly.
RWB_UNKNOWN_BUMP is used when we gradually adjust scale_steps toward the
center state, which is a value of 0.
Signed-off-by: Tang Yizhou <yizhou.tang@shopee.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20250213100611.209997-2-yizhou.tang@shopee.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The loop driver currently uses the logical block size of the underlying
bdev as the lower bound of the loop device block size. While this works
for many cases, it fails for file systems made up of multiple devices
with different logical block sizes (e.g. XFS with a RT device that has a
larger logical block size), or when the file systems doesn't support
direct I/O writes at the sector size granularity (e.g. because it does
out of place writes with a file system block size larger than the sector
size).
Fix this by querying the minimum direct I/O alignment from statx when
available.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250131120120.1315125-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We can't go below the minimum direct I/O size no matter if direct I/O is
enabled by passing in an O_DIRECT file descriptor or due to the explicit
flag. Now that LO_FLAGS_DIRECT_IO is set earlier after assigning a
backing file, loop_default_blocksize can check it instead of the
O_DIRECT flag to handle both conditions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250131120120.1315125-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Assigning LO_FLAGS_DIRECT_IO from the O_DIRECT flag is related to
assigning a new backing file. Move the assignment in preparation
of using the flag more and earlier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250131120120.1315125-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Split the code for setting up a backing file into a helper in preparation
of adding more code to this path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250131120120.1315125-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Remove commented out code.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250219205328.28462-2-thorsten.blum@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit ad934fc1784802fd1408224474b25ee5289fadfc.
loop_queue_work should be strictly serialized to loop_process_work since
the lo_worker could be freed without noticing new work has been queued
again.
Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com>
Link: https://lore.kernel.org/r/20250218065835.19503-1-zhaoyang.huang@unisoc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When rq_qos_wait() is first introduced, it is easy to understand. But
with some bug fixes applied, it is not easy for newcomers to understand
the whole logic under those fixes. In this patch, rq_qos_wait() is
refactored and more comments are added for better understanding. There
are 3 points for the improvement:
1) Use waitqueue_active() instead of wq_has_sleeper() to eliminate
unnecessary memory barrier in wq_has_sleeper() which is supposed
to be used in waker side. In this case, we do need the barrier.
So use the cheaper one to locklessly test for waiters on the queue.
2) Remove acquire_inflight_cb() logic for the first waiter out of the
while loop to make the code clear.
3) Add more comments to explain how to sync with different waiters and
the waker.
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20250208090416.38642-2-songmuchun@bytedance.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There is already a macro DEFINE_WAIT_FUNC() to declare a wait_queue_entry
with a specified waking function. But there is not a counterpart for
initializing one wait_queue_entry with a specified waking function. So
introducing init_wait_func() for this, which also could be used in iocost
and rq-qos. Using default_wake_function() in rq_qos_wait() to wake up
waiters, which could remove ->task field from rq_qos_wait_data.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20250208090416.38642-1-songmuchun@bytedance.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
queue_work could spin on wq->cpu_pwq->pool->lock which could lead to
concurrent loop_process_work failed on lo_work_lock contention and
increase the request latency. Remove this combination by moving the
lock release ahead of queue_work.
Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com>
Link: https://lore.kernel.org/r/20250207091942.3966756-1-zhaoyang.huang@unisoc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Until this point, the kernel can use hardware-wrapped keys to do
encryption if userspace provides one -- specifically a key in
ephemerally-wrapped form. However, no generic way has been provided for
userspace to get such a key in the first place.
Getting such a key is a two-step process. First, the key needs to be
imported from a raw key or generated by the hardware, producing a key in
long-term wrapped form. This happens once in the whole lifetime of the
key. Second, the long-term wrapped key needs to be converted into
ephemerally-wrapped form. This happens each time the key is "unlocked".
In Android, these operations are supported in a generic way through
KeyMint, a userspace abstraction layer. However, that method is
Android-specific and can't be used on other Linux systems, may rely on
proprietary libraries, and also misleads people into supporting KeyMint
features like rollback resistance that make sense for other KeyMint keys
but don't make sense for hardware-wrapped inline encryption keys.
Therefore, this patch provides a generic kernel interface for these
operations by introducing new block device ioctls:
- BLKCRYPTOIMPORTKEY: convert a raw key to long-term wrapped form.
- BLKCRYPTOGENERATEKEY: have the hardware generate a new key, then
return it in long-term wrapped form.
- BLKCRYPTOPREPAREKEY: convert a key from long-term wrapped form to
ephemerally-wrapped form.
These ioctls are implemented using new operations in blk_crypto_ll_ops.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # sm8650
Link: https://lore.kernel.org/r/20250204060041.409950-4-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add sysfs files that indicate which type(s) of keys are supported by the
inline encryption hardware associated with a particular request queue:
/sys/block/$disk/queue/crypto/hw_wrapped_keys
/sys/block/$disk/queue/crypto/raw_keys
Userspace can use the presence or absence of these files to decide what
encyption settings to use.
Don't use a single key_type file, as devices might support both key
types at the same time.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # sm8650
Link: https://lore.kernel.org/r/20250204060041.409950-3-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
To prevent keys from being compromised if an attacker acquires read
access to kernel memory, some inline encryption hardware can accept keys
which are wrapped by a per-boot hardware-internal key. This avoids
needing to keep the raw keys in kernel memory, without limiting the
number of keys that can be used. Such hardware also supports deriving a
"software secret" for cryptographic tasks that can't be handled by
inline encryption; this is needed for fscrypt to work properly.
To support this hardware, allow struct blk_crypto_key to represent a
hardware-wrapped key as an alternative to a raw key, and make drivers
set flags in struct blk_crypto_profile to indicate which types of keys
they support. Also add the ->derive_sw_secret() low-level operation,
which drivers supporting wrapped keys must implement.
For more information, see the detailed documentation which this patch
adds to Documentation/block/inline-encryption.rst.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # sm8650
Link: https://lore.kernel.org/r/20250204060041.409950-2-ebiggers@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Suppress false-positive -Wformat-{overflow,truncation}-non-kprintf
warnings regardless of the W= option
- Avoid CONFIG_TRIM_UNUSED_KSYMS dropping symbols passed to symbol_get()
- Fix a build regression of the Debian linux-headers package
* tag 'kbuild-fixes-v6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: install-extmod-build: add missing quotation marks for CC variable
kbuild: fix misspelling in scripts/Makefile.lib
kbuild: keep symbols for symbol_get() even with CONFIG_TRIM_UNUSED_KSYMS
scripts/Makefile.extrawarn: Do not show clang's non-kprintf warnings at W=1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a recently introduced kernel crash due to a NULL pointer
dereference during system-wide suspend (Rafael Wysocki)"
* tag 'pm-6.14-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: sleep: core: Restrict power.set_active propagation
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Correctly clean the BSS to the PoC before allowing EL2 to access it
on nVHE/hVHE/protected configurations
- Propagate ownership of debug registers in protected mode after the
rework that landed in 6.14-rc1
- Stop pretending that we can run the protected mode without a GICv3
being present on the host
- Fix a use-after-free situation that can occur if a vcpu fails to
initialise the NV shadow S2 MMU contexts
- Always evaluate the need to arm a background timer for fully
emulated guest timers
- Fix the emulation of EL1 timers in the absence of FEAT_ECV
- Correctly handle the EL2 virtual timer, specially when HCR_EL2.E2H==0
s390:
- move some of the guest page table (gmap) logic into KVM itself,
inching towards the final goal of completely removing gmap from the
non-kvm memory management code.
As an initial set of cleanups, move some code from mm/gmap into kvm
and start using __kvm_faultin_pfn() to fault-in pages as needed;
but especially stop abusing page->index and page->lru to aid in the
pgdesc conversion.
x86:
- Add missing check in the fix to defer starting the huge page
recovery vhost_task
- SRSO_USER_KERNEL_NO does not need SYNTHESIZED_F"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (31 commits)
KVM: x86/mmu: Ensure NX huge page recovery thread is alive before waking
KVM: remove kvm_arch_post_init_vm
KVM: selftests: Fix spelling mistake "initally" -> "initially"
kvm: x86: SRSO_USER_KERNEL_NO is not synthesized
KVM: arm64: timer: Don't adjust the EL2 virtual timer offset
KVM: arm64: timer: Correctly handle EL1 timer emulation when !FEAT_ECV
KVM: arm64: timer: Always evaluate the need for a soft timer
KVM: arm64: Fix nested S2 MMU structures reallocation
KVM: arm64: Fail protected mode init if no vgic hardware is present
KVM: arm64: Flush/sync debug state in protected mode
KVM: s390: selftests: Streamline uc_skey test to issue iske after sske
KVM: s390: remove the last user of page->index
KVM: s390: move PGSTE softbits
KVM: s390: remove useless page->index usage
KVM: s390: move gmap_shadow_pgt_lookup() into kvm
KVM: s390: stop using lists to keep track of used dat tables
KVM: s390: stop using page->index for non-shadow gmaps
KVM: s390: move some gmap shadowing functions away from mm/gmap.c
KVM: s390: get rid of gmap_translate()
KVM: s390: get rid of gmap_fault()
...
|
|
Commit 3775fc538f53 ("PM: sleep: core: Synchronize runtime PM status of
parents and children") exposed an issue related to simple_pm_bus_pm_ops
that uses pm_runtime_force_suspend() and pm_runtime_force_resume() as
bus type PM callbacks for the noirq phases of system-wide suspend and
resume.
The problem is that pm_runtime_force_suspend() does not distinguish
runtime-suspended devices from devices for which runtime PM has never
been enabled, so if it sees a device with runtime PM status set to
RPM_ACTIVE, it will assume that runtime PM is enabled for that device
and so it will attempt to suspend it with the help of its runtime PM
callbacks which may not be ready for that. As it turns out, this
causes simple_pm_bus_runtime_suspend() to crash due to a NULL pointer
dereference.
Another problem related to the above commit and simple_pm_bus_pm_ops is
that setting runtime PM status of a device handled by the latter to
RPM_ACTIVE will actually prevent it from being resumed because
pm_runtime_force_resume() only resumes devices with runtime PM status
set to RPM_SUSPENDED.
To mitigate these issues, do not allow power.set_active to propagate
beyond the parent of the device with DPM_FLAG_SMART_SUSPEND set that
will need to be resumed, which should be a sufficient stop-gap for the
time being, but they will need to be properly addressed in the future
because in general during system-wide resume it is necessary to resume
all devices in a dependency chain in which at least one device is going
to be resumed.
Fixes: 3775fc538f53 ("PM: sleep: core: Synchronize runtime PM status of parents and children")
Closes: https://lore.kernel.org/linux-pm/1c2433d4-7e0f-4395-b841-b8eac7c25651@nvidia.com/
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/6137505.lOV4Wx5bFT@rjwysocki.net
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
"Address a KUnit stack initialization regression that got tickled on
m68k, and solve a Clang(v14 and earlier) bug found by 0day:
- Fix stackinit KUnit regression on m68k
- Use ARRAY_SIZE() for memtostr*()/strtomem*()"
* tag 'hardening-v6.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
string.h: Use ARRAY_SIZE() for memtostr*()/strtomem*()
compiler.h: Introduce __must_be_byte_array()
compiler.h: Move C string helpers into C-only kernel section
stackinit: Fix comment for test_small_end
stackinit: Keep selftest union size small on m68k
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp fix from Kees Cook:
"This is really a work-around for x86_64 having grown a syscall to
implement uretprobe, which has caused problems since v6.11.
This may change in the future, but for now, this fixes the unintended
seccomp filtering when uretprobe switched away from traps, and does so
with something that should be easy to backport.
- Allow uretprobe on x86_64 to avoid behavioral complications (Eyal
Birger)"
* tag 'seccomp-v6.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
selftests/seccomp: validate uretprobe syscall passes through seccomp
seccomp: passthrough uretprobe systemcall without filtering
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull execve fix from Kees Cook:
"This is an alpha-specific fix, but since it touched ELF I was asked to
carry it.
- alpha/elf: Fix misc/setarch test of util-linux by removing 32bit
support (Eric W. Biederman)"
* tag 'execve-v6.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
alpha/elf: Fix misc/setarch test of util-linux by removing 32bit support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A number of fairly small fixes, mostly in drivers but two in the core
to change a retry for depopulation (a trendy new hdd thing that
reorganizes blocks away from failing elements) and one to fix a GFP_
annotation to avoid a lock dependency (the third core patch is all in
testing)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla1280: Fix kernel oops when debug level > 2
scsi: ufs: core: Fix error return with query response
scsi: storvsc: Set correct data length for sending SCSI command without payload
scsi: ufs: core: Fix use-after free in init error and remove paths
scsi: core: Do not retry I/Os during depopulation
scsi: core: Use GFP_NOIO to avoid circular locking dependency
scsi: ufs: Fix toggling of clk_gating.state when clock gating is not allowed
scsi: ufs: core: Ensure clk_gating.lock is used only after initialization
scsi: ufs: core: Simplify temperature exception event handling
scsi: target: core: Add line break to status show
scsi: ufs: core: Fix the HIGH/LOW_TEMP Bit Definitions
scsi: core: Add passthrough tests for success and no failure definitions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c reverts from Wolfram Sang:
"It turned out the new mechanism for handling created devices does not
handle all muxing cases.
Revert the changes to give a proper solution more time"
* tag 'i2c-for-6.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: Replace list-based mechanism for handling auto-detected clients"
Revert "i2c: Replace list-based mechanism for handling userspace-created clients"
|
|
Pull rust fixes from Miguel Ojeda:
- Do not export KASAN ODR symbols to avoid gendwarfksyms warnings
- Fix future Rust 1.86.0 (to be released 2025-04-03) x86_64 builds
- Clean future Rust 1.86.0 (to be released 2025-04-03) warning
- Fix future GCC 15 (to be released in a few months) builds
- Fix `rusttest` target in macOS
* tag 'rust-fixes-6.14' of https://github.com/Rust-for-Linux/linux:
x86: rust: set rustc-abi=x86-softfloat on rustc>=1.86.0
rust: kbuild: do not export generated KASAN ODR symbols
rust: kbuild: add -fzero-init-padding-bits to bindgen_skip_cflags
rust: init: use explicit ABI to clean warning in future compilers
rust: kbuild: use host dylib naming in rusttestlib-kernel
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull ftrace fix from Steven Rostedt:
"Function graph fix of notrace functions.
When the function graph tracer was restructured to use the global
section of the meta data in the shadow stack, the bit logic was
changed. There's a TRACE_GRAPH_NOTRACE_BIT that is the bit number in
the mask that tells if the function graph tracer is currently in the
"notrace" mode. The TRACE_GRAPH_NOTRACE is the mask with that bit set.
But when the code we restructured, the TRACE_GRAPH_NOTRACE_BIT was
used when it should have been the TRACE_GRAPH_NOTRACE mask. This made
notrace not work properly"
* tag 'ftrace-v6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
fgraph: Fix set_graph_notrace with setting TRACE_GRAPH_NOTRACE_BIT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"Fix a build regression on GCC 15 builds, caused by GCC changing the
default C version that is overriden in the main Makefile but not in
the x86 boot code Makefile"
* tag 'x86-urgent-2025-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Use '-std=gnu11' to fix build with GCC 15
|
