| Age | Commit message (Collapse) | Author |
|---|
|
This patch fixes the below build warning messages that are
caused due to linking same files to multiple modules by
exporting the required symbols.
"scripts/Makefile.build:244: drivers/net/ethernet/marvell/octeontx2/nic/Makefile:
otx2_devlink.o is added to multiple modules: rvu_nicpf rvu_nicvf
scripts/Makefile.build:244: drivers/net/ethernet/marvell/octeontx2/nic/Makefile:
otx2_dcbnl.o is added to multiple modules: rvu_nicpf rvu_nicvf"
Fixes: 8e67558177f8 ("octeontx2-pf: PFC config support with DCBx").
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LPM consists of HIPM (host initiated power management) and DIPM
(device initiated power management).
ata_eh_set_lpm() will only enable HIPM if both the HBA and the device
supports it.
However, DIPM will be enabled as long as the device supports it.
The HBA will later reject the device's request to enter a power state
that it does not support (Slumber/Partial/DevSleep) (DevSleep is never
initiated by the device).
For a HBA that doesn't support any LPM states, simply don't set a LPM
policy such that all the HIPM/DIPM probing/enabling will be skipped.
Not enabling HIPM or DIPM in the first place is safer than relying on
the device following the AHCI specification and respecting the NAK.
(There are comments in the code that some devices misbehave when
receiving a NAK.)
Performing this check in ahci_update_initial_lpm_policy() also has the
advantage that a HBA that doesn't support any LPM states will take the
exact same code paths as a port that is external/hot plug capable.
Side note: the port in ata_port_dbg() has not been given a unique id yet,
but this is not overly important as the debug print is disabled unless
explicitly enabled using dynamic debug. A follow-up series will make sure
that the unique id assignment will be done earlier. For now, the important
thing is that the function returns before setting the LPM policy.
Fixes: 7627a0edef54 ("ata: ahci: Drop low power policy board type")
Cc: stable@vger.kernel.org
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240618152828.2686771-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
otx2_sq_append_skb makes used of __vlan_hwaccel_push_inside()
to unoffload VLANs - push them from skb meta data into skb data.
However, it omitts a check for __vlan_hwaccel_push_inside()
returning NULL.
Found by inspection based on [1] and [2].
Compile tested only.
[1] Re: [PATCH net-next v1] net: stmmac: Enable TSO on VLANs
https://lore.kernel.org/all/ZmrN2W8Fye450TKs@shell.armlinux.org.uk/
[2] Re: [PATCH net-next v2] net: stmmac: Enable TSO on VLANs
https://lore.kernel.org/all/CANn89i+11L5=tKsa7V7Aeyxaj6nYGRwy35PAbCRYJ73G+b25sg@mail.gmail.com/
Fixes: fd9d7859db6c ("octeontx2-pf: Implement ingress/egress VLAN offload")
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Heng Qi says:
====================
virtio_net: fixes for checksum offloading and XDP handling
This series of patches aim to address two specific issues identified
in the virtio_net driver related to checksum offloading and XDP
processing of fully checksummed packets.
The first patch corrects the handling of checksum offloading in the
driver. The second patch addresses an issue where the XDP program had
no trouble with fully checksummed packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The XDP program can't correctly handle partially checksummed
packets, but works fine with fully checksummed packets. If the
device has already validated fully checksummed packets, then
the driver doesn't need to re-validate them, saving CPU resources.
Additionally, the driver does not drop all partially checksummed
packets when VIRTIO_NET_F_GUEST_CSUM is not negotiated. This is
not a bug, as the driver has always done this.
Fixes: 436c9453a1ac ("virtio-net: keep vnet header zeroed after processing XDP")
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In virtio spec 0.95, VIRTIO_NET_F_GUEST_CSUM was designed to handle
partially checksummed packets, and the validation of fully checksummed
packets by the device is independent of VIRTIO_NET_F_GUEST_CSUM
negotiation. However, the specification erroneously stated:
"If VIRTIO_NET_F_GUEST_CSUM is not negotiated, the device MUST set flags
to zero and SHOULD supply a fully checksummed packet to the driver."
This statement is inaccurate because even without VIRTIO_NET_F_GUEST_CSUM
negotiation, the device can still set the VIRTIO_NET_HDR_F_DATA_VALID flag.
Essentially, the device can facilitate the validation of these packets'
checksums - a process known as RX checksum offloading - removing the need
for the driver to do so.
This scenario is currently not implemented in the driver and requires
correction. The necessary specification correction[1] has been made and
approved in the virtio TC vote.
[1] https://lists.oasis-open.org/archives/virtio-comment/202401/msg00011.html
Fixes: 4f49129be6fa ("virtio-net: Set RXCSUM feature if GUEST_CSUM is available")
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After ecf848eb934b ("net: usb: ax88179_178a: fix link status when link is
set to down/up") to not reset from usbnet_open after the reset from
usbnet_probe at initialization stage to speed up this, some issues have
been reported.
It seems to happen that if the initialization is slower, and some time
passes between the probe operation and the open operation, the second reset
from open is necessary too to have the device working. The reason is that
if there is no activity with the phy, this is "disconnected".
In order to improve this, the solution is to detect when the phy is
"disconnected", and we can use the phy status register for this. So we will
only reset the device from reset operation in this situation, that is, only
if necessary.
The same bahavior is happening when the device is stopped (link set to
down) and later is restarted (link set to up), so if the phy keeps working
we only need to enable the mac again, but if enough time passes between the
device stop and restart, reset is necessary, and we can detect the
situation checking the phy status register too.
cc: stable@vger.kernel.org # 6.6+
Fixes: ecf848eb934b ("net: usb: ax88179_178a: fix link status when link is set to down/up")
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Reported-by: Antje Miederhöfer <a.miederhoefer@gmx.de>
Reported-by: Arne Fitzenreiter <arne_f@ipfire.org>
Tested-by: Yongqin Liu <yongqin.liu@linaro.org>
Tested-by: Antje Miederhöfer <a.miederhoefer@gmx.de>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit
6791e0ea3071 ("x86/resctrl: Access per-rmid structures by index")
adds logic to map individual monitoring groups into a global index space used
for tracking allocated RMIDs.
Attempts to free the default RMID are ignored in free_rmid(), and this works
fine on x86.
With arm64 MPAM, there is a latent bug here however: on platforms with no
monitors exposed through resctrl, each control group still gets a different
monitoring group ID as seen by the hardware, since the CLOSID always forms part
of the monitoring group ID.
This means that when removing a control group, the code may try to free this
group's default monitoring group RMID for real. If there are no monitors
however, the RMID tracking table rmid_ptrs[] would be a waste of memory and is
never allocated, leading to a splat when free_rmid() tries to dereference the
table.
One option would be to treat RMID 0 as special for every CLOSID, but this would
be ugly since bookkeeping still needs to be done for these monitoring group IDs
when there are monitors present in the hardware.
Instead, add a gating check of resctrl_arch_mon_capable() in free_rmid(), and
just do nothing if the hardware doesn't have monitors.
This fix mirrors the gating checks already present in
mkdir_rdt_prepare_rmid_alloc() and elsewhere.
No functional change on x86.
[ bp: Massage commit message. ]
Fixes: 6791e0ea3071 ("x86/resctrl: Access per-rmid structures by index")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://lore.kernel.org/r/20240618140152.83154-1-Dave.Martin@arm.com
|
|
Since commit 2282679fb20b ("mm: submit multipage write for SWP_FS_OPS
swap-space"), we can plug multiple pages then unplug them all together.
That means iov_iter_count(iter) could be way bigger than PAGE_SIZE, it
actually equals the size of iov_iter_npages(iter, INT_MAX).
Note this issue has nothing to do with large folios as we don't support
THP_SWPOUT to non-block devices.
Fixes: 2282679fb20b ("mm: submit multipage write for SWP_FS_OPS swap-space")
Reported-by: Christoph Hellwig <hch@lst.de>
Closes: https://lore.kernel.org/linux-mm/20240614100329.1203579-1-hch@lst.de/
Cc: NeilBrown <neilb@suse.de>
Cc: Anna Schumaker <anna@kernel.org>
Cc: Steve French <sfrench@samba.org>
Cc: Trond Myklebust <trondmy@kernel.org>
Cc: Chuanhua Han <hanchuanhua@oppo.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Chris Li <chrisl@kernel.org>
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Jeff Layton <jlayton@kernel.org>
Cc: Paulo Alcantara <pc@manguebit.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: Shyam Prasad N <sprasad@microsoft.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Bharath SM <bharathsm@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Barry Song <v-songbaohua@oppo.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
commit be27b8965297 ("net: stmmac: replace priv->speed with
the portTransmitRate from the tc-cbs parameters") introduced
a problem. When deleting, it prompts "Invalid portTransmitRate
0 (idleSlope - sendSlope)" and exits. Add judgment on cbs.enable.
Only when offload is enabled, speed divider needs to be calculated.
Fixes: be27b8965297 ("net: stmmac: replace priv->speed with the portTransmitRate from the tc-cbs parameters")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240617013922.1035854-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Get master/slave configuration for initial system start with the link in
down state. This ensures ethtool shows current configuration. Also
fixes link reconfiguration with ethtool while in down state, preventing
ethtool from displaying outdated configuration.
Even though dp83tg720_config_init() is executed periodically as long as
the link is in admin up state but no carrier is detected, this is not
sufficient for the link in admin down state where
dp83tg720_read_status() is not periodically executed. To cover this
case, we need an extra read role configuration in
dp83tg720_config_aneg().
Fixes: cb80ee2f9bee1 ("net: phy: Add support for the DP83TG720S Ethernet PHY")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240614094516.1481231-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case this PHY is bootstrapped for managed mode, we need to manually
wake it. Otherwise no link will be detected.
Cc: stable@vger.kernel.org
Fixes: cb80ee2f9bee1 ("net: phy: Add support for the DP83TG720S Ethernet PHY")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240614094516.1481231-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Milkv Duo does not have a write-protect pin, so disable write protect
to prevent SDcards misdetected as read-only.
Fixes: 89a7056ed4f7 ("riscv: dts: sophgo: add sdcard support for milkv duo")
Signed-off-by: Haylen Chu <heylenay@outlook.com>
Link: https://lore.kernel.org/r/SEYPR01MB4221943C7B101DD2318DA0D3D7CE2@SEYPR01MB4221.apcprd01.prod.exchangelabs.com
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
- filesystems: warn_unused_result warnings
- seccomp: format-zero-length warnings
- fchmodat2: clang build warnings due to-static-libasan
- openat2: clang build warnings due to static-libasan, LOCAL_HDRS
* tag 'linux_kselftest-fixes-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/fchmodat2: fix clang build failure due to -static-libasan
selftests/openat2: fix clang build failures: -static-libasan, LOCAL_HDRS
selftests: seccomp: fix format-zero-length warnings
selftests: filesystems: fix warn_unused_result build warnings
|
|
openvswitch.sh makes use of substitutions of the form ${ns:0:1}, to
obtain the first character of $ns. Empirically, this is works with bash
but not dash. When run with dash these evaluate to an empty string and
printing an error to stdout.
# dash -c 'ns=client; echo "${ns:0:1}"' 2>error
# cat error
dash: 1: Bad substitution
# bash -c 'ns=client; echo "${ns:0:1}"' 2>error
c
# cat error
This leads to tests that neither pass nor fail.
F.e.
TEST: arp_ping [START]
adding sandbox 'test_arp_ping'
Adding DP/Bridge IF: sbx:test_arp_ping dp:arpping {, , }
create namespaces
./openvswitch.sh: 282: eval: Bad substitution
TEST: ct_connect_v4 [START]
adding sandbox 'test_ct_connect_v4'
Adding DP/Bridge IF: sbx:test_ct_connect_v4 dp:ct4 {, , }
./openvswitch.sh: 322: eval: Bad substitution
create namespaces
Resolve this by making openvswitch.sh a bash script.
Fixes: 918423fda910 ("selftests: openvswitch: add an initial flow programming case")
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20240617-ovs-selftest-bash-v1-1-7ae6ccd3617b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On 32bit systems, the "4 * max" multiply can overflow. Use kcalloc()
to do the allocation to prevent this.
Fixes: 44c494c8e30e ("ptp: track available ptp vclocks information")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Link: https://lore.kernel.org/r/ee8110ed-6619-4bd7-9024-28c1f2ac24f4@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While adding a SPI device, the SPI core ensures that multiple logical CS
doesn't map to the same physical CS. For example, spi->chip_select[0] !=
spi->chip_select[1] and so forth. However, unlike the SPI master, the SPI
slave doesn't have the list of chip selects, this leads to probe failure
when the SPI controller is configured as slave. Update the
__spi_add_device() function to perform this check only if the SPI
controller is configured as master.
Fixes: 4d8ff6b0991d ("spi: Add multi-cs memories support in SPI core")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://msgid.link/r/20240617153052.26636-1-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Hardcoding the number of CPUs at compile time does improve code
generation, but if you get it wrong the result will be confusion.
We already limited this earlier to only "experts" (see commit
fe5759d5bfda "cpumask: limit visibility of FORCE_NR_CPUS"), but with
distro kernel configs often having EXPERT enabled, that turns out to not
be much of a limit.
To quote the philosophers at Disney: "Everyone can be an expert. And
when everyone's an expert, no one will be".
There's a runtime warning if you then set nr_cpus to anything but the
forced number, but apparently that can be ignored too [1] and by then
it's pretty much too late anyway.
If we had some real way to limit this to "embedded only", maybe it would
be worth it, but let's see if anybody even notices that the option is
gone. We need to simplify kernel configuration anyway.
Link: https://lore.kernel.org/all/20240618105036.208a8860@rorschach.local.home/ [1]
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Paul McKenney <paulmck@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Bail from outer address space loop, not just the inner memslot loop, when
a "null" handler is encountered by __kvm_handle_hva_range(), which is the
intended behavior. On x86, which has multiple address spaces thanks to
SMM emulation, breaking from just the memslot loop results in undefined
behavior due to assigning the non-existent return value from kvm_null_fn()
to a bool.
In practice, the bug is benign as kvm_mmu_notifier_invalidate_range_end()
is the only caller that passes handler=kvm_null_fn, and it doesn't set
flush_on_ret, i.e. assigning garbage to r.ret is ultimately ignored. And
for most configuration the compiler elides the entire sequence, i.e. there
is no undefined behavior at runtime.
------------[ cut here ]------------
UBSAN: invalid-load in arch/x86/kvm/../../../virt/kvm/kvm_main.c:655:10
load of value 160 is not a valid value for type '_Bool'
CPU: 370 PID: 8246 Comm: CPU 0/KVM Not tainted 6.8.2-amdsos-build58-ubuntu-22.04+ #1
Hardware name: AMD Corporation Sh54p/Sh54p, BIOS WPC4429N 04/25/2024
Call Trace:
<TASK>
dump_stack_lvl+0x48/0x60
ubsan_epilogue+0x5/0x30
__ubsan_handle_load_invalid_value+0x79/0x80
kvm_mmu_notifier_invalidate_range_end.cold+0x18/0x4f [kvm]
__mmu_notifier_invalidate_range_end+0x63/0xe0
__split_huge_pmd+0x367/0xfc0
do_huge_pmd_wp_page+0x1cc/0x380
__handle_mm_fault+0x8ee/0xe50
handle_mm_fault+0xe4/0x4a0
__get_user_pages+0x190/0x840
get_user_pages_unlocked+0xe0/0x590
hva_to_pfn+0x114/0x550 [kvm]
kvm_faultin_pfn+0xed/0x5b0 [kvm]
kvm_tdp_page_fault+0x123/0x170 [kvm]
kvm_mmu_page_fault+0x244/0xaa0 [kvm]
vcpu_enter_guest+0x592/0x1070 [kvm]
kvm_arch_vcpu_ioctl_run+0x145/0x8a0 [kvm]
kvm_vcpu_ioctl+0x288/0x6d0 [kvm]
__x64_sys_ioctl+0x8f/0xd0
do_syscall_64+0x77/0x120
entry_SYSCALL_64_after_hwframe+0x6e/0x76
</TASK>
---[ end trace ]---
Fixes: 071064f14d87 ("KVM: Don't take mmu_lock for range invalidation unless necessary")
Signed-off-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/b8723d39903b64c241c50f5513f804390c7b5eec.1718203311.git.babu.moger@amd.com
[sean: massage changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
"Another small set of EFI fixes. Only the x86 one is likely to affect
any actual users (and has a cc:stable), but the issue it fixes was
only observed in an unusual context (kexec in a confidential VM).
- Ensure that EFI runtime services are not unmapped by PAN on ARM
- Avoid freeing the memory holding the EFI memory map inadvertently
on x86
- Avoid a false positive kmemleak warning on arm64"
* tag 'efi-fixes-for-v6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi/arm64: Fix kmemleak false positive in arm64_efi_rt_init()
efi/x86: Free EFI memory map only when installing a new one.
efi/arm: Disable LPAE PAN when calling EFI runtime services
|
|
Add OCTAL mode support.
Issue detected using "--octal" spidev_test's option.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://msgid.link/r/20240618132951.2743935-4-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In case usage of OCTAL mode, buswidth parameter can take the value 8.
As return value of stm32_qspi_get_mode() is used to configure fields
of CCR registers that are 2 bits only (fields IMODE, ADMODE, ADSIZE,
DMODE), clamp return value of stm32_qspi_get_mode() to 4.
Fixes: a557fca630cc ("spi: stm32_qspi: Add transfer_one_message() spi callback")
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://msgid.link/r/20240618132951.2743935-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Misplaced parenthesis make test of mode wrong in case mode is equal to
SPI_TX_OCTAL or SPI_RX_OCTAL.
Simplify this sanity test, if one of this bit is set, property
cs-gpio must be present in DT.
Fixes: a557fca630cc ("spi: stm32_qspi: Add transfer_one_message() spi callback")
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://msgid.link/r/20240618132951.2743935-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
zones_ht is a global hashtable for flow_table with zone as key. However,
it does not consider netns when getting a flow_table from zones_ht in
tcf_ct_init(), and it means an act_ct action in netns A may get a
flow_table that belongs to netns B if it has the same zone value.
In Shuang's test with the TOPO:
tcf2_c <---> tcf2_sw1 <---> tcf2_sw2 <---> tcf2_s
tcf2_sw1 and tcf2_sw2 saw the same flow and used the same flow table,
which caused their ct entries entering unexpected states and the
TCP connection not able to end normally.
This patch fixes the issue simply by adding netns into the key of
tcf_ct_flow_table so that an act_ct action gets a flow_table that
belongs to its own netns in tcf_ct_init().
Note that for easy coding we don't use tcf_ct_flow_table.nf_ft.net,
as the ct_ft is initialized after inserting it to the hashtable in
tcf_ct_flow_table_get() and also it requires to implement several
functions in rhashtable_params including hashfn, obj_hashfn and
obj_cmpfn.
Fixes: 64ff70b80fd4 ("net/sched: act_ct: Offload established connections to flow table")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1db5b6cc6902c5fc6f8c6cbd85494a2008087be5.1718488050.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As it says in commit 3bc07321ccc2 ("xfrm: Force a dst refcount before
entering the xfrm type handlers"):
"Crypto requests might return asynchronous. In this case we leave the
rcu protected region, so force a refcount on the skb's destination
entry before we enter the xfrm type input/output handlers."
On TIPC decryption path it has the same problem, and skb_dst_force()
should be called before doing decryption to avoid a possible crash.
Shuang reported this issue when this warning is triggered:
[] WARNING: include/net/dst.h:337 tipc_sk_rcv+0x1055/0x1ea0 [tipc]
[] Kdump: loaded Tainted: G W --------- - - 4.18.0-496.el8.x86_64+debug
[] Workqueue: crypto cryptd_queue_worker
[] RIP: 0010:tipc_sk_rcv+0x1055/0x1ea0 [tipc]
[] Call Trace:
[] tipc_sk_mcast_rcv+0x548/0xea0 [tipc]
[] tipc_rcv+0xcf5/0x1060 [tipc]
[] tipc_aead_decrypt_done+0x215/0x2e0 [tipc]
[] cryptd_aead_crypt+0xdb/0x190
[] cryptd_queue_worker+0xed/0x190
[] process_one_work+0x93d/0x17e0
Fixes: fc1b6d6de220 ("tipc: introduce TIPC encryption & authentication")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/fbe3195fad6997a4eec62d9bf076b2ad03ac336b.1718476040.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
syzbot found hanging tasks waiting on rtnl_lock [1]
A reproducer is available in the syzbot bug.
When a request to add multiple actions with the same index is sent, the
second request will block forever on the first request. This holds
rtnl_lock, and causes tasks to hang.
Return -EAGAIN to prevent infinite looping, while keeping documented
behavior.
[1]
INFO: task kworker/1:0:5088 blocked for more than 143 seconds.
Not tainted 6.9.0-rc4-syzkaller-00173-g3cdb45594619 #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/1:0 state:D stack:23744 pid:5088 tgid:5088 ppid:2 flags:0x00004000
Workqueue: events_power_efficient reg_check_chans_work
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5409 [inline]
__schedule+0xf15/0x5d00 kernel/sched/core.c:6746
__schedule_loop kernel/sched/core.c:6823 [inline]
schedule+0xe7/0x350 kernel/sched/core.c:6838
schedule_preempt_disabled+0x13/0x30 kernel/sched/core.c:6895
__mutex_lock_common kernel/locking/mutex.c:684 [inline]
__mutex_lock+0x5b8/0x9c0 kernel/locking/mutex.c:752
wiphy_lock include/net/cfg80211.h:5953 [inline]
reg_leave_invalid_chans net/wireless/reg.c:2466 [inline]
reg_check_chans_work+0x10a/0x10e0 net/wireless/reg.c:2481
Fixes: 0190c1d452a9 ("net: sched: atomically check-allocate action")
Reported-by: syzbot+b87c222546179f4513a7@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=b87c222546179f4513a7
Signed-off-by: David Ruth <druth@chromium.org>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20240614190326.1349786-1-druth@chromium.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Raju Lakkaraju says:
====================
net: lan743x: Fixes for multiple WOL related issues
This patch series implement the following fixes:
1. Disable WOL upon resume in order to restore full data path operation
2. Support WOL at both the PHY and MAC appropriately
3. Remove interrupt mask clearing from config_init
Patch-3 was sent seperately earlier. Review comments in link:
https://lore.kernel.org/lkml/4a565d54-f468-4e32-8a2c-102c1203f72c@lunn.ch/T/
====================
Link: https://lore.kernel.org/r/20240614171157.190871-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When the system resumes from sleep, the phy_init_hw() function invokes
config_init(), which clears all interrupt masks and causes wake events to be
lost in subsequent wake sequences. Remove interrupt mask clearing from
config_init() and preserve relevant masks in config_intr().
Fixes: 7d901a1e878a ("net: phy: add Maxlinear GPY115/21x/24x driver")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Prevent options not supported by the PHY from being requested to it by the MAC
Whenever a WOL option is supported by both, the PHY is given priority
since that usually leads to better power savings.
Fixes: e9e13b6adc33 ("lan743x: fix for potential NULL pointer dereference with bare card")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When Wake-on-LAN (WoL) is active and the system is in suspend mode, triggering
a system event can wake the system from sleep, which may block the data path.
To restore normal data path functionality after waking, disable all wake-up
events. Furthermore, clear all Write 1 to Clear (W1C) status bits by writing
1's to them.
Fixes: 4d94282afd95 ("lan743x: Add power management support")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If it enter to runtime D3 state, it didn't shutup Headset MIC pin.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/8d86f61e7d6f4a03b311e4eb4e5caaef@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
With ARCH=m68k, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in sound/oss/dmasound/dmasound_core.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/20240617-md-m68k-sound-oss-dmasound-v1-1-5c19306be930@quicinc.com
|
|
The whole mechanism to remember occurred SPI interrupts is not atomic,
which could lead to unexpected behavior. So fix this by using atomic bit
operations instead.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20240614145030.7781-1-wahrenst@gmx.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Syzkaller hit a warning:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 3 PID: 7890 at lib/refcount.c:25 refcount_warn_saturate+0xdf/0x1d0
Modules linked in:
CPU: 3 PID: 7890 Comm: tun Not tainted 6.10.0-rc3-00100-gcaa4f9578aba-dirty #310
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:refcount_warn_saturate+0xdf/0x1d0
Code: 41 49 04 31 ff 89 de e8 9f 1e cd fe 84 db 75 9c e8 76 26 cd fe c6 05 b6 41 49 04 01 90 48 c7 c7 b8 8e 25 86 e8 d2 05 b5 fe 90 <0f> 0b 90 90 e9 79 ff ff ff e8 53 26 cd fe 0f b6 1
RSP: 0018:ffff8881067b7da0 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff811c72ac
RDX: ffff8881026a2140 RSI: ffffffff811c72b5 RDI: 0000000000000001
RBP: ffff8881067b7db0 R08: 0000000000000000 R09: 205b5d3730353139
R10: 0000000000000000 R11: 205d303938375420 R12: ffff8881086500c4
R13: ffff8881086500c4 R14: ffff8881086500b0 R15: ffff888108650040
FS: 00007f5b2961a4c0(0000) GS:ffff88823bd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055d7ed36fd18 CR3: 00000001482f6000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? show_regs+0xa3/0xc0
? __warn+0xa5/0x1c0
? refcount_warn_saturate+0xdf/0x1d0
? report_bug+0x1fc/0x2d0
? refcount_warn_saturate+0xdf/0x1d0
? handle_bug+0xa1/0x110
? exc_invalid_op+0x3c/0xb0
? asm_exc_invalid_op+0x1f/0x30
? __warn_printk+0xcc/0x140
? __warn_printk+0xd5/0x140
? refcount_warn_saturate+0xdf/0x1d0
get_net_ns+0xa4/0xc0
? __pfx_get_net_ns+0x10/0x10
open_related_ns+0x5a/0x130
__tun_chr_ioctl+0x1616/0x2370
? __sanitizer_cov_trace_switch+0x58/0xa0
? __sanitizer_cov_trace_const_cmp2+0x1c/0x30
? __pfx_tun_chr_ioctl+0x10/0x10
tun_chr_ioctl+0x2f/0x40
__x64_sys_ioctl+0x11b/0x160
x64_sys_call+0x1211/0x20d0
do_syscall_64+0x9e/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f5b28f165d7
Code: b3 66 90 48 8b 05 b1 48 2d 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 81 48 2d 00 8
RSP: 002b:00007ffc2b59c5e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f5b28f165d7
RDX: 0000000000000000 RSI: 00000000000054e3 RDI: 0000000000000003
RBP: 00007ffc2b59c650 R08: 00007f5b291ed8c0 R09: 00007f5b2961a4c0
R10: 0000000029690010 R11: 0000000000000246 R12: 0000000000400730
R13: 00007ffc2b59cf40 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Kernel panic - not syncing: kernel: panic_on_warn set ...
This is trigger as below:
ns0 ns1
tun_set_iff() //dev is tun0
tun->dev = dev
//ip link set tun0 netns ns1
put_net() //ref is 0
__tun_chr_ioctl() //TUNGETDEVNETNS
net = dev_net(tun->dev);
open_related_ns(&net->ns, get_net_ns); //ns1
get_net_ns()
get_net() //addition on 0
Use maybe_get_net() in get_net_ns in case net's ref is zero to fix this
Fixes: 0c3e0e3bb623 ("tun: Add ioctl() TUNGETDEVNETNS cmd to allow obtaining real net ns of tun device")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20240614131302.2698509-1-yuehaibing@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm
Pull lsm fix from Paul Moore:
"A single LSM/IMA patch to fix a problem caused by sleeping while in a
RCU critical section"
* tag 'lsm-pr-20240617' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
ima: Avoid blocking in RCU read-side critical section
|
|
ip6_dst_idev() can return NULL, xfrm6_get_saddr() must act accordingly.
syzbot reported:
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 1 PID: 12 Comm: kworker/u8:1 Not tainted 6.10.0-rc2-syzkaller-00383-gb8481381d4e2 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
Workqueue: wg-kex-wg1 wg_packet_handshake_send_worker
RIP: 0010:xfrm6_get_saddr+0x93/0x130 net/ipv6/xfrm6_policy.c:64
Code: df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 97 00 00 00 4c 8b ab d8 00 00 00 48 b8 00 00 00 00 00 fc ff df 4c 89 ea 48 c1 ea 03 <80> 3c 02 00 0f 85 86 00 00 00 4d 8b 6d 00 e8 ca 13 47 01 48 b8 00
RSP: 0018:ffffc90000117378 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff88807b079dc0 RCX: ffffffff89a0d6d7
RDX: 0000000000000000 RSI: ffffffff89a0d6e9 RDI: ffff88807b079e98
RBP: ffff88807ad73248 R08: 0000000000000007 R09: fffffffffffff000
R10: ffff88807b079dc0 R11: 0000000000000007 R12: ffffc90000117480
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8880b9300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f4586d00440 CR3: 0000000079042000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
xfrm_get_saddr net/xfrm/xfrm_policy.c:2452 [inline]
xfrm_tmpl_resolve_one net/xfrm/xfrm_policy.c:2481 [inline]
xfrm_tmpl_resolve+0xa26/0xf10 net/xfrm/xfrm_policy.c:2541
xfrm_resolve_and_create_bundle+0x140/0x2570 net/xfrm/xfrm_policy.c:2835
xfrm_bundle_lookup net/xfrm/xfrm_policy.c:3070 [inline]
xfrm_lookup_with_ifid+0x4d1/0x1e60 net/xfrm/xfrm_policy.c:3201
xfrm_lookup net/xfrm/xfrm_policy.c:3298 [inline]
xfrm_lookup_route+0x3b/0x200 net/xfrm/xfrm_policy.c:3309
ip6_dst_lookup_flow+0x15c/0x1d0 net/ipv6/ip6_output.c:1256
send6+0x611/0xd20 drivers/net/wireguard/socket.c:139
wg_socket_send_skb_to_peer+0xf9/0x220 drivers/net/wireguard/socket.c:178
wg_socket_send_buffer_to_peer+0x12b/0x190 drivers/net/wireguard/socket.c:200
wg_packet_send_handshake_initiation+0x227/0x360 drivers/net/wireguard/send.c:40
wg_packet_handshake_send_worker+0x1c/0x30 drivers/net/wireguard/send.c:51
process_one_work+0x9fb/0x1b60 kernel/workqueue.c:3231
process_scheduled_works kernel/workqueue.c:3312 [inline]
worker_thread+0x6c8/0xf70 kernel/workqueue.c:3393
kthread+0x2c1/0x3a0 kernel/kthread.c:389
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240615154231.234442-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot caught a NULL dereference in rt6_probe() [1]
Bail out if __in6_dev_get() returns NULL.
[1]
Oops: general protection fault, probably for non-canonical address 0xdffffc00000000cb: 0000 [#1] PREEMPT SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000658-0x000000000000065f]
CPU: 1 PID: 22444 Comm: syz-executor.0 Not tainted 6.10.0-rc2-syzkaller-00383-gb8481381d4e2 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
RIP: 0010:rt6_probe net/ipv6/route.c:656 [inline]
RIP: 0010:find_match+0x8c4/0xf50 net/ipv6/route.c:758
Code: 14 fd f7 48 8b 85 38 ff ff ff 48 c7 45 b0 00 00 00 00 48 8d b8 5c 06 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 19
RSP: 0018:ffffc900034af070 EFLAGS: 00010203
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffc90004521000
RDX: 00000000000000cb RSI: ffffffff8990d0cd RDI: 000000000000065c
RBP: ffffc900034af150 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000002 R12: 000000000000000a
R13: 1ffff92000695e18 R14: ffff8880244a1d20 R15: 0000000000000000
FS: 00007f4844a5a6c0(0000) GS:ffff8880b9300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b31b27000 CR3: 000000002d42c000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
rt6_nh_find_match+0xfa/0x1a0 net/ipv6/route.c:784
nexthop_for_each_fib6_nh+0x26d/0x4a0 net/ipv4/nexthop.c:1496
__find_rr_leaf+0x6e7/0xe00 net/ipv6/route.c:825
find_rr_leaf net/ipv6/route.c:853 [inline]
rt6_select net/ipv6/route.c:897 [inline]
fib6_table_lookup+0x57e/0xa30 net/ipv6/route.c:2195
ip6_pol_route+0x1cd/0x1150 net/ipv6/route.c:2231
pol_lookup_func include/net/ip6_fib.h:616 [inline]
fib6_rule_lookup+0x386/0x720 net/ipv6/fib6_rules.c:121
ip6_route_output_flags_noref net/ipv6/route.c:2639 [inline]
ip6_route_output_flags+0x1d0/0x640 net/ipv6/route.c:2651
ip6_dst_lookup_tail.constprop.0+0x961/0x1760 net/ipv6/ip6_output.c:1147
ip6_dst_lookup_flow+0x99/0x1d0 net/ipv6/ip6_output.c:1250
rawv6_sendmsg+0xdab/0x4340 net/ipv6/raw.c:898
inet_sendmsg+0x119/0x140 net/ipv4/af_inet.c:853
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg net/socket.c:745 [inline]
sock_write_iter+0x4b8/0x5c0 net/socket.c:1160
new_sync_write fs/read_write.c:497 [inline]
vfs_write+0x6b6/0x1140 fs/read_write.c:590
ksys_write+0x1f8/0x260 fs/read_write.c:643
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: 52e1635631b3 ("[IPV6]: ROUTE: Add router_probe_interval sysctl.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240615151454.166404-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reminds us that in6_dev_get() can return NULL.
fib6_nh_init()
ip6_validate_gw( &idev )
ip6_route_check_nh( idev )
*idev = in6_dev_get(dev); // can be NULL
Oops: general protection fault, probably for non-canonical address 0xdffffc00000000bc: 0000 [#1] PREEMPT SMP KASAN PTI
KASAN: null-ptr-deref in range [0x00000000000005e0-0x00000000000005e7]
CPU: 0 PID: 11237 Comm: syz-executor.3 Not tainted 6.10.0-rc2-syzkaller-00249-gbe27b8965297 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/07/2024
RIP: 0010:fib6_nh_init+0x640/0x2160 net/ipv6/route.c:3606
Code: 00 00 fc ff df 4c 8b 64 24 58 48 8b 44 24 28 4c 8b 74 24 30 48 89 c1 48 89 44 24 28 48 8d 98 e0 05 00 00 48 89 d8 48 c1 e8 03 <42> 0f b6 04 38 84 c0 0f 85 b3 17 00 00 8b 1b 31 ff 89 de e8 b8 8b
RSP: 0018:ffffc900032775a0 EFLAGS: 00010202
RAX: 00000000000000bc RBX: 00000000000005e0 RCX: 0000000000000000
RDX: 0000000000000010 RSI: ffffc90003277a54 RDI: ffff88802b3a08d8
RBP: ffffc900032778b0 R08: 00000000000002fc R09: 0000000000000000
R10: 00000000000002fc R11: 0000000000000000 R12: ffff88802b3a08b8
R13: 1ffff9200064eec8 R14: ffffc90003277a00 R15: dffffc0000000000
FS: 00007f940feb06c0(0000) GS:ffff8880b9400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000000245e8000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
ip6_route_info_create+0x99e/0x12b0 net/ipv6/route.c:3809
ip6_route_add+0x28/0x160 net/ipv6/route.c:3853
ipv6_route_ioctl+0x588/0x870 net/ipv6/route.c:4483
inet6_ioctl+0x21a/0x280 net/ipv6/af_inet6.c:579
sock_do_ioctl+0x158/0x460 net/socket.c:1222
sock_ioctl+0x629/0x8e0 net/socket.c:1341
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f940f07cea9
Fixes: 428604fb118f ("ipv6: do not set routes if disable_ipv6 has been enabled")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240614082002.26407-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is important to have fixed (sub)test names in TAP, because these
names are used to identify them. If they are not fixed, tracking cannot
be done.
Some subtests from the userspace_pm selftest were using random numbers
in their names: the client and server address IDs from $RANDOM, and the
client port number randomly picked by the kernel when creating the
connection. These values have been replaced by 'client' and 'server'
words: that's even more helpful than showing random numbers. Note that
the addresses IDs are incremented and decremented in the test: +1 or -1
are then displayed in these cases.
Not to loose info that can be useful for debugging in case of issues,
these random numbers are now displayed at the beginning of the test.
Fixes: f589234e1af0 ("selftests: mptcp: userspace_pm: format subtests results in TAP")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240614-upstream-net-20240614-selftests-mptcp-uspace-pm-fixed-test-names-v1-1-460ad3edb429@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some applications were reporting ETIMEDOUT errors on apparently
good looking flows, according to packet dumps.
We were able to root cause the issue to an accidental setting
of tp->retrans_stamp in the following scenario:
- client sends TFO SYN with data.
- server has TFO disabled, ACKs only SYN but not payload.
- client receives SYNACK covering only SYN.
- tcp_ack() eats SYN and sets tp->retrans_stamp to 0.
- tcp_rcv_fastopen_synack() calls tcp_xmit_retransmit_queue()
to retransmit TFO payload w/o SYN, sets tp->retrans_stamp to "now",
but we are not in any loss recovery state.
- TFO payload is ACKed.
- we are not in any loss recovery state, and don't see any dupacks,
so we don't get to any code path that clears tp->retrans_stamp.
- tp->retrans_stamp stays non-zero for the lifetime of the connection.
- after first RTO, tcp_clamp_rto_to_user_timeout() clamps second RTO
to 1 jiffy due to bogus tp->retrans_stamp.
- on clamped RTO with non-zero icsk_retransmits, retransmits_timed_out()
sets start_ts from tp->retrans_stamp from TFO payload retransmit
hours/days ago, and computes bogus long elapsed time for loss recovery,
and suffers ETIMEDOUT early.
Fixes: a7abf3cd76e1 ("tcp: consider using standard rtx logic in tcp_rcv_fastopen_synack()")
CC: stable@vger.kernel.org
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Co-developed-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240614130615.396837-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mmap_base by default"
This reverts commit 3afb76a66b5559a7b595155803ce23801558a7a9.
This was a wrongheaded workaround for an issue that had already been
fixed much better by commit 4ef9ad19e176 ("mm: huge_memory: don't force
huge page alignment on 32 bit").
Asking users questions at kernel compile time that they can't make sense
of is not a viable strategy. And the fact that even the kernel VM
maintainers apparently didn't catch that this "fix" is not a fix any
more pretty much proves the point that people can't be expected to
understand the implications of the question.
It may well be the case that we could improve things further, and that
__thp_get_unmapped_area() should take the mapping randomization into
account even for 64-bit kernels. Maybe we should not be so eager to use
THP mappings.
But in no case should this be a kernel config option.
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch over to using the new Intel CPU model defines, as the old ones
are going away.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Raptor Lake models
Dell laptops with IPU6 camera (the Tiger Lake, Alder Lake and Raptor
Lake generations) have broken ACPI MIPI DISCO information (this results
from an OEM attempt to make Linux work by supplying it with custom data
in the ACPI tables which has never been supported in the mainline).
Instead of adding a lot of DMI quirks for this, check for Dell platforms
based on the processor generations in question and drop the ACPI graph
port nodes, likely to be created with the help of invalid data, on all
of them.
Fixes: bd721b934323 ("ACPI: scan: Extract CSI-2 connection graph from _CRS")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"Mainly MM singleton fixes. And a couple of ocfs2 regression fixes"
* tag 'mm-hotfixes-stable-2024-06-17-11-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
kcov: don't lose track of remote references during softirqs
mm: shmem: fix getting incorrect lruvec when replacing a shmem folio
mm/debug_vm_pgtable: drop RANDOM_ORVALUE trick
mm: fix possible OOB in numa_rebuild_large_mapping()
mm/migrate: fix kernel BUG at mm/compaction.c:2761!
selftests: mm: make map_fixed_noreplace test names stable
mm/memfd: add documentation for MFD_NOEXEC_SEAL MFD_EXEC
mm: mmap: allow for the maximum number of bits for randomizing mmap_base by default
gcov: add support for GCC 14
zap_pid_ns_processes: clear TIF_NOTIFY_SIGNAL along with TIF_SIGPENDING
mm: huge_memory: fix misused mapping_large_folio_support() for anon folios
lib/alloc_tag: fix RCU imbalance in pgalloc_tag_get()
lib/alloc_tag: do not register sysctl interface when CONFIG_SYSCTL=n
MAINTAINERS: remove Lorenzo as vmalloc reviewer
Revert "mm: init_mlocked_on_free_v3"
mm/page_table_check: fix crash on ZONE_DEVICE
gcc: disable '-Warray-bounds' for gcc-9
ocfs2: fix NULL pointer dereference in ocfs2_abort_trigger()
ocfs2: fix NULL pointer dereference in ocfs2_journal_dirty()
|
|
Undo the modifications made in commit d410ee5109a1 ("ACPICA: avoid
"Info: mapping multiple BARs. Your kernel is fine.""). The initial
purpose of this commit was to stop memory mappings for operation
regions from overlapping page boundaries, as it can trigger warnings
if different page attributes are present.
However, it was found that when this situation arises, mapping
continues until the boundary's end, but there is still an attempt to
read/write the entire length of the map, leading to a NULL pointer
deference. For example, if a four-byte mapping request is made but
only one byte is mapped because it hits the current page boundary's
end, a four-byte read/write attempt is still made, resulting in a NULL
pointer deference.
Instead, map the entire length, as the ACPI specification does not
mandate that it must be within the same page boundary. It is
permissible for it to be mapped across different regions.
Link: https://github.com/acpica/acpica/pull/954
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218849
Fixes: d410ee5109a1 ("ACPICA: avoid "Info: mapping multiple BARs. Your kernel is fine."")
Co-developed-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
- yama: document function parameter (Christian Göttsche)
- mm/util: Swap kmemdup_array() arguments (Jean-Philippe Brucker)
- kunit/overflow: Adjust for __counted_by with DEFINE_RAW_FLEX()
- MAINTAINERS: Update entries for Kees Cook
* tag 'hardening-v6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
MAINTAINERS: Update entries for Kees Cook
kunit/overflow: Adjust for __counted_by with DEFINE_RAW_FLEX()
yama: document function parameter
mm/util: Swap kmemdup_array() arguments
|
|
Update current email address for Kees Cook in the MAINTAINER file to
match the change from commit 4e173c825b19 ("mailmap: update entry for
Kees Cook").
Link: https://lore.kernel.org/r/20240617181257.work.206-kees@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V fixes from Wei Liu:
- Some cosmetic changes for hv.c and balloon.c (Aditya Nagesh)
- Two documentation updates (Michael Kelley)
- Suppress the invalid warning for packed member alignment (Saurabh
Sengar)
- Two hv_balloon fixes (Michael Kelley)
* tag 'hyperv-fixes-signed-20240616' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
Drivers: hv: Cosmetic changes for hv.c and balloon.c
Documentation: hyperv: Improve synic and interrupt handling description
Documentation: hyperv: Update spelling and fix typo
tools: hv: suppress the invalid warning for packed member alignment
hv_balloon: Enable hot-add for memblock sizes > 128 MiB
hv_balloon: Use kernel macros to simplify open coded sequences
|
|
Grab nfsd_mutex lock in nfsd_nl_rpc_status_get_dumpit routine and remove
nfsd_nl_rpc_status_get_start() and nfsd_nl_rpc_status_get_done(). This
patch fix the syzbot log reported below:
INFO: task syz-executor.1:17770 blocked for more than 143 seconds.
Not tainted 6.10.0-rc3-syzkaller-00022-gcea2a26553ac #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz-executor.1 state:D stack:23800 pid:17770 tgid:17767 ppid:11381 flags:0x00000006
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5408 [inline]
__schedule+0x17e8/0x4a20 kernel/sched/core.c:6745
__schedule_loop kernel/sched/core.c:6822 [inline]
schedule+0x14b/0x320 kernel/sched/core.c:6837
schedule_preempt_disabled+0x13/0x30 kernel/sched/core.c:6894
__mutex_lock_common kernel/locking/mutex.c:684 [inline]
__mutex_lock+0x6a4/0xd70 kernel/locking/mutex.c:752
nfsd_nl_listener_get_doit+0x115/0x5d0 fs/nfsd/nfsctl.c:2124
genl_family_rcv_msg_doit net/netlink/genetlink.c:1115 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline]
genl_rcv_msg+0xb16/0xec0 net/netlink/genetlink.c:1210
netlink_rcv_skb+0x1e5/0x430 net/netlink/af_netlink.c:2564
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219
netlink_unicast_kernel net/netlink/af_netlink.c:1335 [inline]
netlink_unicast+0x7ec/0x980 net/netlink/af_netlink.c:1361
netlink_sendmsg+0x8db/0xcb0 net/netlink/af_netlink.c:1905
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x223/0x270 net/socket.c:745
____sys_sendmsg+0x525/0x7d0 net/socket.c:2585
___sys_sendmsg net/socket.c:2639 [inline]
__sys_sendmsg+0x2b0/0x3a0 net/socket.c:2668
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f24ed27cea9
RSP: 002b:00007f24ee0080c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f24ed3b3f80 RCX: 00007f24ed27cea9
RDX: 0000000000000000 RSI: 0000000020000100 RDI: 0000000000000005
RBP: 00007f24ed2ebff4 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
Fixes: 1bd773b4f0c9 ("nfsd: hold nfsd_mutex across entire netlink operation")
Fixes: bd9d6a3efa97 ("NFSD: add rpc_status netlink support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
Sourbh reported an oops that is triggerable by trying to read the
pool_stats procfile before nfsd had been started. Move the check for a
NULL serv in svc_pool_stats_start above the mutex acquisition, and fix
the stop routine not to unlock the mutex if there is no serv yet.
Fixes: 7b207ccd9833 ("svc: don't hold reference for poolstats, only mutex.")
Reported-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Tested-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
