| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.7-rc cycle:
- Two boot warning fixes from the RCU tree that should have gotten
merged several weeks ago already but did not because of issues
with who merges them. Paul has now split the RCU warning fixes into
sets for various maintainers.
- Fix ams-delta FIQ regression caused by omap1 sparse IRQ changes
- Fix PM for omap3 boards using timer12 and gptimer, like the
original beagleboard
- Fix hangs on am437x-sk-evm by lowering the I2C bus speed
* tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
ARM: OMAP2+: timer: add probe for clocksources
ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
arm: Use _rcuidle for smp_cross_call() tracepoints
arm: Use _rcuidle tracepoint to allow use from idle
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch fixes a non-booting issue in Mainline.
When booting with a compressed kernel, we need to be careful how we
populate memory close to DDR start. AUTO_ZRELADDR is enabled by default
in multi-arch enabled configurations, which place some restrictions on
where the kernel is placed and where it will be uncompressed to on boot.
AUTO_ZRELADDR takes the decompressor code's start address and masks out
the bottom 28 bits to obtain an address to uncompress the kernel to
(thus a load address of 0x42000000 means that the kernel will be
uncompressed to 0x40000000 i.e. DDR START on this platform).
Even changing the load address to after the co-processor's shared memory
won't render a booting platform, since the AUTO_ZRELADDR algorithm still
ensures the kernel is uncompressed into memory shared with the first
co-processor (0x40000000).
Another option would be to move loading to 0x4A000000, since this will
mean the decompressor will decompress the kernel to 0x48000000. However,
this would mean a large chunk (0x44000000 => 0x48000000 (64MB)) of
memory would essentially be wasted for no good reason.
Until we can work with ST to find a suitable memory location to
relocate co-processor shared memory, let's disable the shared memory
nodes. This will ensure a working platform in the mean time.
NB: The more observant of you will notice that we're leaving the DMU
shared memory node enabled; this is because a) it is the only one in
active use at the time of this writing and b) it is not affected by
the current default behaviour which is causing issues.
Fixes: fe135c6 (ARM: dts: STiH407: Move over to using the 'reserved-memory' API for obtaining DMA memory)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.7:
- Correct Micrel PHY mask to fix the issue that i.MX6UL ethernet works
in U-Boot but not in kernel.
* tag 'imx-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6ul: Fix Micrel PHY mask
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When OpenSFS took over lustre.org, there was some reshuffling.
FIDs on ZFS document is now at
http://wiki.old.lustre.org/index.php/Architecture_-_Interoperability_fids_zfs
instead of the old location, so update comments accordingly.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes all checkpatch occurences of
"CHECK: No space is necessary after a cast"
in Lustre code.
Signed-off-by: Emoly Liu <emoly.liu@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes all checkpatch occurences of
"CHECK: Logical continuations should be on the previous line"
in Lustre code.
Signed-off-by: Emoly Liu <emoly.liu@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes one checkpatch warning in lustre:
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Emoly Liu <emoly.liu@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The semaphore 'rf_sem' in rtl8192u has no users, hence removing it.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The semaphore 'scan_sem' in rtl8192u is a simple mutex, so it should
be written as one. Semaphores are going away in the future.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The semaphore 'wx_sem' in ieee80211_device is a simple mutex,
so it should be written as one. Semaphores are going away in the future.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The semaphore 'wx_sem' in r8192_priv is a simple mutex, so
it should be written as one. Semaphores are going away in the future.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Propagate errors from kzalloc and usb_control_msg and change the
return type of write_nic_dword from void to int.
Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Propagate errors from kzalloc and usb_control_msg and change the
return type of write_nic_word from void to int.
Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Propagate errors from kzalloc and usb_control_msg and change the
return type of write_nic_byte_E from void to int.
Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Propagate errors from kzalloc and usb_control_msg and change the
return type of write_nic_byte from void to int.
Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The call of rtl8192_read_eeprom_info may fail, therefore its return
value must be checked and propagated in the case of error
Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Propagate error from eprom_read and change the return type of
rtl8192_read_eeprom_info from void to int.
Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The call of eprom_read may fail, therefore its return value must be
checked
Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Propagate error from eprom_r and change the return type of eprom_read
from u32 to int.
Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The call of read_nic_word_E may fail, therefore its return value must be
checked and propagated in the case of error.
Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
enc->rx_seq[] and enc->key[] are arrays, not pointers and they can't be
NULL. Let's remove these NULL checks.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We are upstream now, we don't need seperate driver versioning.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Until we switch to cfg80211 (if ever), we must do this manually.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no need to continue then. Also, this enables us to remove an
ugly static variable.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move read/write functions to the top and driver struct to the end, so we
can remove all forward declarations.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
No 79xx anymore, this is confusing. Add a comment saying that old
versions were probably named 7910/79xx.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
So the module will be loaded automatically on card insertion. Rename the
array while here.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Includes probably need a driver-wide clean up, but for now let's at
least group all includes from the sdio file together.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
I verified that all but two settings from the config file can be set up
also via 'iwconfig' or 'iwpriv'. The two missing are ROM_FILE and
PhyInformationTimer. ROM_FILE can be easily dropped. There is only one
known firmware floating on the net, so, the name is fix and we can make
this constant. Frankly, I don't know when PhyInformationTimer needs to
be set to non-zero. But if we need it somewhen, there is already
(currently commented out) code to add this as another private method, so
we could use that. Summa summarum: We can remove the config file
handling and the example config file. The only useful action,
initialization of the configuration struct, is now moved to the sdio
main file.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull ARM fixes from Russell King:
"A couple of fixes for pmd_mknotpresent()/pmd_present() for LPAE
systems"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8579/1: mm: Fix definition of pmd_mknotpresent
ARM: 8578/1: mm: ensure pmd_present only checks the valid bit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a bunch (65) of USB fixes for 4.7-rc4. Sorry about the
quantity, I've been slow in getting these out.
The majority are the "normal" gadget, musb, and xhci fixes, that we
all are used to. There are also a few other tiny fixes resolving a
number of reported issues that showed up in 4.7-rc1.
All of these have been in linux-next"
* tag 'usb-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
usbip: rate limit get_frame_number message
usb: musb: sunxi: Remove bogus "Frees glue" comment
usb: musb: sunxi: Fix NULL ptr deref when gadget is registered before musb
usb: echi-hcd: Add ehci_setup check before echi_shutdown
usb: host: ehci-msm: Conditionally call ehci suspend/resume
MAINTAINERS: Add file patterns for usb device tree bindings
usb: host: ehci-tegra: Avoid getting the same reset twice
usb: host: ehci-tegra: Grab the correct UTMI pads reset
USB: mos7720: delete parport
USB: OHCI: Don't mark EDs as ED_OPER if scheduling fails
phy: ti-pipe3: Program the DPLL even if it was already locked
usb: musb: Stop bulk endpoint while queue is rotated
usb: musb: Ensure rx reinit occurs for shared_fifo endpoints
usb: musb: host: correct cppi dma channel for isoch transfer
usb: musb: only restore devctl when session was set in backup
usb: phy: Check initial state for twl6030
usb: musb: Use normal module_init for 2430 glue
usb: musb: Remove pm_runtime_set_irq_safe
usb: musb: Remove extra PM runtime calls from 2430 glue layer
usb: musb: Return error value from musb_mailbox
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO and staging fixes from Greg KH:
"Here are a number of IIO and staging bugfixes for 4.7-rc4.
Nothing huge, the normal amount of iio driver fixes, and some small
staging driver bugfixes for some reported problems (2 are reverts of
patches that went into 4.7-rc1). All have been in linux-next with no
reported issues"
* tag 'staging-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (24 commits)
Revert "Staging: rtl8188eu: rtw_efuse: Use sizeof type *pointer instead of sizeof type."
Revert "Staging: drivers: rtl8188eu: use sizeof(*ptr) instead of sizeof(struct)"
staging: lustre: lnet: Don't access NULL NI on failure path
iio: hudmidity: hdc100x: fix incorrect shifting and scaling
iio: light apds9960: Add the missing dev.parent
iio: Fix error handling in iio_trigger_attach_poll_func
iio: st_sensors: Disable DRDY at init time
iio: st_sensors: Init trigger before irq request
iio: st_sensors: switch to a threaded interrupt
iio: light: bh1780: assign a static name
iio: bh1780: dereference the client properly
iio: humidity: hdc100x: fix IIO_TEMP channel reporting
iio:st_pressure: fix sampling gains (bring inline with ABI)
iio: proximity: as3935: fix buffer stack trashing
iio: proximity: as3935: remove triggered buffer processing
iio: proximity: as3935: correct IIO_CHAN_INFO_RAW output
max44000: Remove scale from proximity
iio: humidity: am2315: Remove a stray unlock
iio: humidity: hdc100x: correct humidity integration time mask
iio: pressure: bmp280: fix error message for wrong chip id
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are a small number of debugfs, ISA, and one driver core fix for
4.7-rc4.
All of these resolve reported issues. The ISA ones have spent the
least amount of time in linux-next, sorry about that, I didn't realize
they were regressions that needed to get in now (thanks to Thorsten
for the prodding!) but they do all pass the 0-day bot tests. The
others have been in linux-next for a while now.
Full details about them are in the shortlog below"
* tag 'driver-core-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
isa: Dummy isa_register_driver should return error code
isa: Call isa_bus_init before dependent ISA bus drivers register
watchdog: ebc-c384_wdt: Allow build for X86_64
iio: stx104: Allow build for X86_64
gpio: Allow PC/104 devices on X86_64
isa: Allow ISA-style drivers on modern systems
base: make module_create_drivers_dir race-free
debugfs: open_proxy_open(): avoid double fops release
debugfs: full_proxy_open(): free proxy on ->open() failure
kernel/kcov: unproxify debugfs file's fops
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a small number of char and misc driver fixes for 4.7-rc4.
They resolve some minor issues that have been reported, and have all
been in linux-next"
* tag 'char-misc-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
coresight: Handle build path error
coresight: Fix erroneous memset in tmc_read_unprepare_etr
coresight: Fix tmc_read_unprepare_etr
coresight: Fix NULL pointer dereference in _coresight_build_path
extcon: palmas: Fix boot up state of VBUS when using GPIO detection
mcb: Acquire reference to carrier module in core
mcb: Acquire reference to device in probe
mei: don't use wake_up_interruptible for wr_ctrl
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"The most user visible change here is a fix for our recent superblock
validation checks that were causing problems on non-4k pagesized
systems"
* 'for-linus-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: btrfs_check_super_valid: Allow 4096 as stripesize
btrfs: remove build fixup for qgroup_account_snapshot
btrfs: use new error message helper in qgroup_account_snapshot
btrfs: avoid blocking open_ctree from cleaner_kthread
Btrfs: don't BUG_ON() in btrfs_orphan_add
btrfs: account for non-CoW'd blocks in btrfs_abort_transaction
Btrfs: check if extent buffer is aligned to sectorsize
btrfs: Use correct format specifier
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Revert a recent ACPICA commit that introduced a suspend-to-RAM
regression on one system due to incorrect information in its ACPI
tables that had not been taken into consideration at all before (and
everything worked), but the commit in question started to use it"
* tag 'acpi-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPICA: ACPI 2.0, Hardware: Add access_width/bit_offset support for acpi_hw_write()"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fixes for two recent regressions that may lead to degraded performance
(operating performance points framework, intel_pstate).
Specifics:
- Fix a recent regression in the intel_pstate driver that may lead to
degraded performance on some systems due to missing turbo state
entry in the table returned by the ACPI _PSS object (Srinivas
Pandruvada).
- Fix a recent regression in the OPP (operating performance points)
framework that may lead to degraded performance on some systems
where the OPP table is created too early (Viresh Kumar)"
* tag 'pm-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / OPP: Add 'UNKNOWN' status for shared_opp in struct opp_table
cpufreq: intel_pstate: Adjust _PSS[0] freqeuency if needed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID subsystem fixes from Jiri Kosina:
- kernel panic fix in hid-elo from Oliver Neukum
- Surface Pro 3 device quirk from Benjamin Tissoires
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: multitouch: Add MT_QUIRK_NOT_SEEN_MEANS_UP to Surface Pro 3
HID: elo: kill not flush the work
|
|
Since commit 49d200deaa68 ("debugfs: prevent access to removed files'
private data"), a debugfs file's file_operations methods get proxied
through lifetime aware wrappers.
However, only a certain subset of the file_operations members is supported
by debugfs and ->compat_ioctl isn't among them -- it appears to be NULL
from the VFS layer's perspective.
This behaviour breaks the /sys/kernel/debug/sync/sw_sync file introduced
concurrently with commit a44eb74cd413 ("staging/android: move SW_SYNC_USER
to a debugfs file").
Since that file never gets removed, there is no file removal race and thus,
a lifetime checking proxy isn't needed.
Avoid the proxying for /sys/kernel/debug/sync/sw_sync by creating it via
debugfs_create_file_unsafe() rather than debugfs_create_file().
For consistency, do the same for /sys/kernel/debug/sync/info.
Fixes: 49d200deaa68 ("debugfs: prevent access to removed files' private data")
Fixes: a44eb74cd413 ("staging/android: move SW_SYNC_USER to a debugfs file")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SW_SYNC only works with DEBUG_FS so state it in the Kconfig file.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This header file only contains information for debugging and SW_SYNC, so
rename it to sync_debug.h instead of having a more generic name.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As it is internal to sw_sync now this value will always be "sw_sync".
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This function was just used by the file release function, so we just fold
its content there and remove sync_timeline_destroy().
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'destroyed' was set but not used ny anyone.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We don't want to export this from the kernel. This is interface is only
for testing and debug. So testers shall copy the ioctl info in their own
projects.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The only use sync_timeline will have in upstream kernel is for debugging
through the SW_SYNC interface. So make it internal to SW_SYNC to avoid
people use it in the future.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Most of the includes there are not necessary anymore.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Split sync_debug and sw_sync in two different files.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move the list_head members from sync_pt to struct fence was a mistake,
they will not be used by struct fence as planned before, so here we create
sync_pt again to bring the list heads back.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
