| Age | Commit message (Collapse) | Author |
|---|
|
Add ASP1_FRAME_CONTROL1, ASP1_FRAME_CONTROL5 and the ASP1_TX?_INPUT
registers to the sequence used to initialize the ASP configuration.
Write this sequence to the cache and directly to the registers to
ensure that they match.
A system-specific firmware can patch these registers to values that are
not the silicon default, so that the CS35L56 boots already in the
configuration used by Windows or by "driverless" Windows setups such
as factory tuning.
These may not match how Linux is configuring the HDA codec. And anyway
on Linux the ALSA controls are used to configure routing options.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9caea ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Link: https://msgid.link/r/20240129162737.497-10-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Patch the SDW TX mixer registers to silicon defaults.
CS35L56 is designed for SDCA and a generic SDCA driver would
know nothing about these chip-specific registers. So the
firmware sets up the SDW TX mixer registers to whatever audio
is relevant on a specific system.
This means that the driver cannot assume the initial values
of these registers. But Linux has ALSA controls to configure
routing, so the registers can be patched to silicon default and
the ALSA controls used to select what audio to feed back to the
host capture path.
Backport note:
This won't apply to kernels older than v6.6.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e49611252900 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://msgid.link/r/20240129162737.497-9-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a dummy SUPPLY widget connected to the ASP that forces the
chip registers to match the regmap cache when the ASP is
powered-up.
On a SoundWire system the ASP is free for use as a chip-to-chip
interconnect. This can be either for the firmware on multiple
CS35L56 to share reference audio; or as a bridge to another
device. If it is a firmware interconnect it is owned by the
firmware and the Linux driver should avoid writing the registers.
However. If it is a bridge then Linux may take over and handle
it as a normal codec-to-codec link.
CS35L56 is designed for SDCA and a generic SDCA driver would
know nothing about these chip-specific registers. So if the
ASP is being used on a SoundWire system the firmware sets up the
ASP registers. This means that we can't assume the default
state of the ASP registers. But we don't know the initial state
that the firmware set them to until after the firmware has been
downloaded and booted, which can take several seconds when
downloading multiple amps.
To avoid blocking probe() for several seconds waiting for the
firmware, the silicon defaults are assumed. This allows the machine
driver to setup the ASP configuration during probe() without being
blocked. If the ASP is hooked up and used, the SUPPLY widget
ensures that the chip registers match what was configured in the
regmap cache.
If the machine driver does not hook up the ASP, it is assumed that
it won't call any functions to configure the ASP DAI. Therefore
the regmap cache will be clean for these registers so a
regcache_sync() will not overwrite the chip registers. If the
DAI is not hooked up, the dummy SUPPLY widget will not be
invoked so it will never force-overwrite the chip registers.
Backport note:
This won't apply cleanly to kernels older than v6.6.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e49611252900 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://msgid.link/r/20240129162737.497-8-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove the check of fw_patched from cs35l56_is_fw_reload_needed().
Also remove the redundant check for control of the reset GPIO.
The fw_patched flag is set when cs35l56_dsp_work() has completed its
steps to download firmware and power-up wm_adsp. There was a check in
cs35l56_is_fw_reload_needed() to make a quick exit of 'false' if
!fw_patched. The original idea was that the system might be suspended
before the driver has ever made any attempt to download firmware, and
in that case the driver doesn't need to return to a patched state
because it was never in a patched state.
This check of fw_patched is buggy because it prevented ever recovering
from a failed patch. If a previous attempt to patch and reboot the
silicon had failed it would leave fw_patched==false. This would mean
the driver never attempted another download even though the fault may
have been cleared (by a hard reset, for example).
It is also a redundant check because the calling code already makes
a quick exit if cs35l56_component_probe() has not been called, which
deals with the original intent of this check but in a safer way.
The check for reset GPIO is redundant: if the silicon was hard-reset
the FIRMWARE_MISSING flag will be 1. But this check created an
expectation that the suspend/resume code toggles reset. This can't
easily be protected against accidental code breakage. The only reason
for the check was to skip runtime-resuming the driver to read the
PROTECTION_STATUS register when it already knows it reset the silicon.
But in that case the driver will have to be runtime-resumed to do
the firmware download. So it created an assumption for no benefit.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 8a731fd37f8b ("ASoC: cs35l56: Move utility functions to shared file")
Link: https://msgid.link/r/20240129162737.497-7-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the call to cs35l56_set_patch() earlier in cs35l56_init() so
that it only adds the register patch on first-time initialization.
The call was after the post_soft_reset label, so every time this
function was run to re-initialize the hardware after a reset it would
call regmap_register_patch() and add the same reg_sequence again.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 898673b905b9 ("ASoC: cs35l56: Move shared data into a common data structure")
Link: https://msgid.link/r/20240129162737.497-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
cs35l56_component_remove() must call wm_adsp_power_down() and
wm_adsp2_component_remove().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e49611252900 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://msgid.link/r/20240129162737.497-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The cs35l56->component pointer is used by the suspend-resume handling to
know whether the driver is fully instantiated. This is to prevent it
queuing dsp_work which would result in calling wm_adsp when the driver
is not an instantiated ASoC component. So this pointer must be cleared
by cs35l56_component_remove().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e49611252900 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://msgid.link/r/20240129162737.497-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There's no need to overwrite fwf_name with a kstrdup() of the cs_dsp part
name. It is trivial to select either fwf_name or cs_dsp.part as the string
to use when building the filename in wm_adsp_request_firmware_file().
This leaves fwf_name entirely owned by the codec driver.
It also avoids problems with freeing the pointer. With the original code
fwf_name was either a pointer owned by the codec driver, or a kstrdup()
created by wm_adsp. This meant wm_adsp must free it if it set it, but not
if the codec driver set it. The code was handling this by using
devm_kstrdup().
But there is no absolute requirement that wm_adsp_common_init() must be
called from probe(), so this was a pseudo-memory leak - each new call to
wm_adsp_common_init() would allocate another block of memory but these
would only be freed if the owning codec driver was removed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://msgid.link/r/20240129162737.497-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Check for the cases of system-specific bin file without a
wmfw before falling back to looking for a generic wmfw.
All system-specific options should be tried before falling
back to loading a generic wmfw/bin. With the original code,
the presence of a fallback generic wmfw on the filesystem
would prevent using a system-specific tuning with a ROM
firmware.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 0e7d82cbea8b ("ASoC: wm_adsp: Add support for loading bin files without wmfw")
Link: https://msgid.link/r/20240129162737.497-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.8
Quite a lot of fixes that came in since the merge window, a large
portion for for Qualcomm and ES8326.
The 8 DAI support for Qualcomm is just raising a constant to allow for
devies that otherwise only need DTs, and there's a few other device ID
updates for sunxi (Allwinner) and AMD platforms.
|
|
There currently exists two thinkpad headset jack fixups:
ALC285_FIXUP_THINKPAD_NO_BASS_SPK_HEADSET_JACK
ALC285_FIXUP_THINKPAD_HEADSET_JACK
The latter is applied to alc285 and alc287 thinkpads which contain
bass speakers.
However, the former was only being applied to alc285 thinkpads,
leaving non-bass alc287 thinkpads with no headset button controls.
This patch fixes that by adding ALC285_FIXUP_THINKPAD_NO_BASS_SPK_HEADSET_JACK
to the alc287 chains, allowing the detection of headset buttons.
Signed-off-by: José Relvas <josemonsantorelvas@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240131113407.34698-3-josemonsantorelvas@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add 4 missing formats to 'snd_pcm_format_names' array in order to be
able to get their names with 'snd_pcm_format_name' function.
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20240125223522.1122765-1-ivan.orlov0322@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Adds sound support for ASUS Zenbook UM3402YAR with missing DSD
Signed-off-by: Chhayly Leang <clw.leang@gmail.com>
Link: https://lore.kernel.org/r/20240126080912.87422-1-clw.leang@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add new model entry into configuration table.
Signed-off-by: Kenzo Gomez <kenzo.sgomez@gmail.com>
Link: https://lore.kernel.org/r/20240127164621.26431-1-kenzo.sgomez@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Previous commit that added support for Huawei MateBook D16 2021
with Ryzen 4600H (HVY-WXX9 M1010) was incomplete.
To activate support for this laptop, the DMI table in
acp3x-es83xx machine driver must also be updated.
Fixes: b5338b1b901e ("ASoC: amd: acp: Add support for a new Huawei Matebook laptop")
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Link: https://msgid.link/r/20240128172229.657142-1-posteuca@mutex.one
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Chen-Yu Tsai <wens@kernel.org>:
This series adds SPDIF controllers for the H616 and H618.
There's also a fix for SPDIF on H6: the controller also has a
receiver that was not correctly modeled.
|
|
The SPDIF hardware block found in the H616 SoC has the same layout as
the one found in the H6 SoC, except that it is missing the receiver
side.
Add a new compatible string for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://msgid.link/r/20240127163247.384439-3-wens@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the H6 was added to the bindings, only the TX DMA channel was
added. As the hardware supports both transmit and receive functions,
the binding is missing the RX DMA channel and is thus incorrect.
Also, the reset control was not made mandatory.
Add the RX DMA channel for SPDIF on H6 by removing the compatible from
the list of compatibles that should only have a TX DMA channel. And add
the H6 compatible to the list of compatibles that require the reset
control to be present.
Fixes: b20453031472 ("dt-bindings: sound: sun4i-spdif: Add Allwinner H6 compatible")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://msgid.link/r/20240127163247.384439-2-wens@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SPDIF hardware block found in the H616 SoC has the same layout as
the one found in the H6 SoC, except that it is missing the receiver
side.
Since the driver currently only supports the transmit function, support
for the H616 is identical to what is currently done for the H6.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://msgid.link/r/20240127163247.384439-4-wens@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The laptop requires a quirk ID to enable its internal microphone. Add
it to the DMI quirk table.
Reported-by: Techno Mooney <techno.mooney@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218402
Cc: stable@vger.kernel.org
Signed-off-by: Techno Mooney <techno.mooney@gmail.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://msgid.link/r/20240129081148.1044891-1-bagasdotme@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Many devices with a single alternate setting do not have a Valid
Alternate Setting Control and validation performed by
validate_sample_rate_table_v2v3() doesn't work on them and is not
really needed. So check the presense of control before sending
altsetting validation requests.
MOTU Microbook IIc is suffering the most without this check. It
takes up to 40 seconds to bootup due to how slow it switches
sampling rates:
[ 2659.164824] usb 3-2: New USB device found, idVendor=07fd, idProduct=0004, bcdDevice= 0.60
[ 2659.164827] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2659.164829] usb 3-2: Product: MicroBook IIc
[ 2659.164830] usb 3-2: Manufacturer: MOTU
[ 2659.166204] usb 3-2: Found last interface = 3
[ 2679.322298] usb 3-2: No valid sample rate available for 1:1, assuming a firmware bug
[ 2679.322306] usb 3-2: 1:1: add audio endpoint 0x3
[ 2679.322321] usb 3-2: Creating new data endpoint #3
[ 2679.322552] usb 3-2: 1:1 Set sample rate 96000, clock 1
[ 2684.362250] usb 3-2: 2:1: cannot get freq (v2/v3): err -110
[ 2694.444700] usb 3-2: No valid sample rate available for 2:1, assuming a firmware bug
[ 2694.444707] usb 3-2: 2:1: add audio endpoint 0x84
[ 2694.444721] usb 3-2: Creating new data endpoint #84
[ 2699.482103] usb 3-2: 2:1 Set sample rate 96000, clock 1
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20240129121254.3454481-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This reverts commit 67794f882adca00d043899ac248bc002751da9f6.
We need to explicitly set up the clock selector to workaround a problem
with the Behringer mixers. This was originally done in d2e8f641257d
("ALSA: usb-audio: Explicitly set up the clock selector")
The problem with MOTU M Series mentioned in commit message was fixed in
a different way by checking control capabilities of clock selectors.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20240128132338.819273-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This HP Laptop uses ALC236 codec with COEF 0x07 controlling the
mute LED. Enable existing quirk for this device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240128155704.2333812-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
1 SF114-32
If you connect an external headset/microphone to the 3.5mm jack on the
Acer Swift 1 SF114-32 it does not recognize the microphone. This fixes
that and gives the user the ability to choose between internal and
headset mic.
Signed-off-by: David Senoner <seda18@rolmail.net>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240126155626.2304465-1-seda18@rolmail.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Dan Williams:
"A build regression fix, a device compatibility fix, and an original
bug preventing creation of large (16 device) interleave sets:
- Fix unit test build regression fallout from global
"missing-prototypes" change
- Fix compatibility with devices that do not support interrupts
- Fix overflow when calculating the capacity of large interleave sets"
* tag 'cxl-fixes-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/region：Fix overflow issue in alloc_hpa()
cxl/pci: Skip irq features if MSI/MSI-X are not supported
tools/testing/nvdimm: Disable "missing prototypes / declarations" warnings
tools/testing/cxl: Disable "missing prototypes / declarations" warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- fix boot issue on single core Lantiq Danube devices
- fix boot issue on Loongson64 platforms
- fix improper FPU setup
- fix missing prototypes issues
* tag 'mips-fixes_6.8_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mips: Call lose_fpu(0) before initializing fcr31 in mips_set_personality_nan
MIPS: loongson64: set nid for reserved memblock region
Revert "MIPS: loongson64: set nid for reserved memblock region"
MIPS: lantiq: register smp_ops on non-smp platforms
MIPS: loongson64: set nid for reserved memblock region
MIPS: reserve exception vector space ONLY ONCE
MIPS: BCM63XX: Fix missing prototypes
MIPS: sgi-ip32: Fix missing prototypes
MIPS: sgi-ip30: Fix missing prototypes
MIPS: fw arc: Fix missing prototypes
MIPS: sgi-ip27: Fix missing prototypes
MIPS: Alchemy: Fix missing prototypes
MIPS: Cobalt: Fix missing prototypes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Borislav Petkov:
- Prevent an inconsistent futex operation leading to stale state
exposure
* tag 'locking_urgent_for_v6.8_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Prevent the reuse of stale pi_state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
- Initialize the resend node of each IRQ descriptor, not only the first
one
* tag 'irq_urgent_for_v6.8_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Initialize resend_node hlist for all interrupt descriptors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Borislav Petkov:
- Preserve the number of idle calls and sleep entries across CPU
hotplug events in order to be able to compute correct averages
- Limit the duration of the clocksource watchdog checking interval as
too long intervals lead to wrongly marking the TSC as unstable
* tag 'timers_urgent_for_v6.8_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/sched: Preserve number of idle sleeps across CPU hotplug events
clocksource: Skip watchdog check for large watchdog intervals
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Make sure 32-bit syscall registers are properly sign-extended
- Add detection for AMD's Zen5 generation CPUs and Intel's Clearwater
Forest CPU model number
- Make a stub function export non-GPL because it is part of the
paravirt alternatives and that can be used by non-GPL code
* tag 'x86_urgent_for_v6.8_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Add more models to X86_FEATURE_ZEN5
x86/entry/ia32: Ensure s32 is sign extended to s64
x86/cpu: Add model number for Intel Clearwater Forest processor
x86/CPU/AMD: Add X86_FEATURE_ZEN5
x86/paravirt: Make BUG_func() usable by non-GPL modules
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock
Pull memblock fix from Mike Rapoport:
"Fix crash when reserved memory is not added to memory.
When CONFIG_DEFERRED_STRUCT_PAGE_INIT is enabled, the initialization
of reserved pages may cause access of NODE_DATA() with invalid nid and
crash.
Add a fall back to early_pfn_to_nid() in memmap_init_reserved_pages()
to ensure a valid node id is always passed to init_reserved_page()"
* tag 'fixes-2024-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
memblock: fix crash when reserved memory is not added to memory
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- WMI bus driver fixes
- Second attempt (previously reverted) at P2SB PCI rescan deadlock fix
- AMD PMF driver improvements
- MAINTAINERS updates
- Misc other small fixes and hw-id additions
* tag 'platform-drivers-x86-v6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: touchscreen_dmi: Add info for the TECLAST X16 Plus tablet
platform/x86/intel/ifs: Call release_firmware() when handling errors.
platform/x86/amd/pmf: Fix memory leak in amd_pmf_get_pb_data()
platform/x86/amd/pmf: Get ambient light information from AMD SFH driver
platform/x86/amd/pmf: Get Human presence information from AMD SFH driver
platform/mellanox: mlxbf-pmc: Fix offset calculation for crspace events
platform/mellanox: mlxbf-tmfifo: Drop Tx network packet when Tx TmFIFO is full
MAINTAINERS: remove defunct acpi4asus project info from asus notebooks section
MAINTAINERS: add Luke Jones as maintainer for asus notebooks
MAINTAINERS: Remove Perry Yuan as DELL WMI HARDWARE PRIVACY SUPPORT maintainer
platform/x86: silicom-platform: Add missing "Description:" for power_cycle sysfs attr
platform/x86: intel-wmi-sbl-fw-update: Fix function name in error message
platform/x86: p2sb: Use pci_resource_n() in p2sb_read_bar0()
platform/x86: p2sb: Allow p2sb_bar() calls during PCI device probe
platform/x86: intel-uncore-freq: Fix types in sysfs callbacks
platform/x86: wmi: Fix wmi_dev_probe()
platform/x86: wmi: Fix notify callback locking
platform/x86: wmi: Decouple legacy WMI notify handlers from wmi_block_list
platform/x86: wmi: Return immediately if an suitable WMI event is found
platform/x86: wmi: Fix error handling in legacy WMI notify handler functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix boot failure on machines with more than 8 nodes, and fix two build
errors about KVM"
* tag 'loongarch-fixes-6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: KVM: Add returns to SIMD stubs
LoongArch: KVM: Fix build due to API changes
LoongArch/smp: Call rcutree_report_cpu_starting() at tlb_init()
|
|
Pull xfs fix from Chandan Babu:
- Fix read only mounts when using fsopen mount API
* tag 'xfs-6.8-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: read only mounts with fsopen mount API are busted
|
|
Pull bcachefs fixes from Kent Overstreet:
- fix for REQ_OP_FLUSH usage; this fixes filesystems going read only
with -EOPNOTSUPP from the block layer.
(this really should have gone in with the block layer patch causing
the -EOPNOTSUPP, or should have gone in before).
- fix an allocation in non-sleepable context
- fix one source of srcu lock latency, on devices with terrible discard
latency
- fix a reattach_inode() issue in fsck
* tag 'bcachefs-2024-01-26' of https://evilpiepirate.org/git/bcachefs:
bcachefs: __lookup_dirent() works in snapshot, not subvol
bcachefs: discard path uses unlock_long()
bcachefs: fix incorrect usage of REQ_OP_FLUSH
bcachefs: Add gfp flags param to bch2_prt_task_backtrace()
|
|
Pull smb server fixes from Steve French:
- Fix netlink OOB
- Minor kernel doc fix
* tag '6.8-rc2-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: fix global oob in ksmbd_nl_policy
smb: Fix some kernel-doc comments
|
|
Pull smb client fixes from Steve French:
"Nine cifs/smb client fixes
- Four network error fixes (three relating to replays of requests
that need to be retried, and one fixing some places where we were
returning the wrong rc up the stack on network errors)
- Two multichannel fixes including locking fix and case where subset
of channels need reconnect
- netfs integration fixup: share remote i_size with netfslib
- Two small cleanups (one for addressing a clang warning)"
* tag '6.8-rc1-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix stray unlock in cifs_chan_skip_or_disable
cifs: set replay flag for retries of write command
cifs: commands that are retried should have replay flag set
cifs: helper function to check replayable error codes
cifs: translate network errors on send to -ECONNABORTED
cifs: cifs_pick_channel should try selecting active channels
cifs: Share server EOF pos with netfslib
smb: Work around Clang __bdos() type confusion
smb: client: delete "true", "false" defines
|
|
If we still own the FPU after initializing fcr31, when we are preempted
the dirty value in the FPU will be read out and stored into fcr31,
clobbering our setting. This can cause an improper floating-point
environment after execve(). For example:
zsh% cat measure.c
#include <fenv.h>
int main() { return fetestexcept(FE_INEXACT); }
zsh% cc measure.c -o measure -lm
zsh% echo $((1.0/3)) # raising FE_INEXACT
0.33333333333333331
zsh% while ./measure; do ; done
(stopped in seconds)
Call lose_fpu(0) before setting fcr31 to prevent this.
Closes: https://lore.kernel.org/linux-mips/7a6aa1bbdbbe2e63ae96ff163fab0349f58f1b9e.camel@xry111.site/
Fixes: 9b26616c8d9d ("MIPS: Respect the ISA level in FCSR handling")
Cc: stable@vger.kernel.org
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Commit 61167ad5fecd("mm: pass nid to reserve_bootmem_region()") reveals
that reserved memblock regions have no valid node id set, just set it
right since loongson64 firmware makes it clear in memory layout info.
This works around booting failure on 3A1000+ since commit 61167ad5fecd
("mm: pass nid to reserve_bootmem_region()") under
CONFIG_DEFERRED_STRUCT_PAGE_INIT.
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
This reverts commit ce7b1b97776ec0b068c4dd6b6dbb48ae09a23519.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata updates from Niklas Cassel:
- Fix an incorrect link_power_management_policy sysfs attribute value.
We were previously using the same attribute value for two different
LPM policies (me)
- Add a ASMedia ASM1166 quirk.
The SATA host controller always reports that it has 32 ports, even
though it only has six ports. Add a quirk that overrides the value
reported by the controller (Conrad)
- Add a ASMedia ASM1061 quirk.
The SATA host controller completely ignores the upper 21 bits of the
DMA address. This causes IOMMU error events when a (valid) DMA
address actually has any of the upper 21 bits set. Add a quirk that
limits the dma_mask to 43-bits (Lennert)
* tag 'ata-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ahci: add 43-bit DMA address quirk for ASMedia ASM1061 controllers
ahci: asm1166: correct count of reported ports
ata: libata-sata: improve sysfs description for ATA_LPM_UNKNOWN
|
|
Pull block fixes from Jens Axboe:
- RCU warning fix for md (Mikulas)
- Fix for an aoe issue that lockdep rightfully complained about
(Maksim)
- Fix for an error code change in partitioning that caused a regression
with some tools (Li)
- Fix for a data direction warning with bi-direction commands
(Christian)
* tag 'block-6.8-2024-01-26' of git://git.kernel.dk/linux:
md: fix a suspicious RCU usage warning
aoe: avoid potential deadlock at set_capacity
block: Fix WARNING in _copy_from_iter
block: Move checking GENHD_FL_NO_PART to bdev_add_partition()
|
|
Pull io_uring fix from Jens Axboe:
"Just a single tweak to the newly added IORING_OP_FIXED_FD_INSTALL from
Paul, ensuring it goes via the audit path and playing it safe by
excluding it from using registered creds"
* tag 'io_uring-6.8-2024-01-26' of git://git.kernel.dk/linux:
io_uring: enable audit and restrict cred override for IORING_OP_FIXED_FD_INSTALL
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control update from Rafael Wysocki:
"Remove some dead code from the Intel powerclamp thermal control driver
(Srinivas Pandruvada)"
* tag 'thermal-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel: powerclamp: Remove dead code for target mwait value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two cpufreq drivers and the cpupower utility.
Specifics:
- Fix the handling of scaling_max/min_freq sysfs attributes in the
AMD P-state cpufreq driver (Mario Limonciello)
- Make the intel_pstate cpufreq driver avoid unnecessary computation
of the HWP performance level corresponding to a given frequency in
the cases when it is known already, which also helps to avoid
reducing the maximum CPU capacity artificially on some systems
(Rafael J. Wysocki)
- Fix compilation of the cpupower utility when CFLAGS is passed as a
make argument for cpupower, but it does not take effect as expected
due to mishandling (Stanley Chan)"
* tag 'pm-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq/amd-pstate: Fix setting scaling max/min freq values
cpufreq: intel_pstate: Refine computation of P-state for given frequency
tools cpupower bench: Override CFLAGS assignments
|
|
Pull documentation fixes from Jonathan Corbet:
"A handful of relatively boring documentation fixes"
* tag 'docs-6.8-fixes' of git://git.lwn.net/linux:
docs: admin-guide: remove obsolete advice related to SLAB allocator
doc: admin-guide/kernel-parameters: remove useless comment
docs/accel: correct links to mailing list archives
docs/sphinx: Fix TOC scroll hack for the home page
|
|
Pull drm fixes from Dave Airlie:
"Lots going on for rc2, ivpu has a bunch of stabilisation and debugging
work, then amdgpu and xe are the main fixes. i915, exynos have a few,
then some misc panel and bridge fixes.
Worth mentioning are three regressions. One of the nouveau fixes in
6.7 for a serious deadlock had side effects, so I guess we will bring
back the deadlock until I can figure out what should be done properly.
There was a scheduler regression vs amdgpu which was reported in a few
places and is now fixed. There was an i915 vs simpledrm problem
resulting in black screens, that is reverted also.
I'll be working on a proper nouveau fix, it kinda looks like one of
those cases where someone tried to use an atomic where they should
have probably used a lock, but I'll see.
fb:
- fix simpledrm/i915 regression by reverting change
scheduler:
- fix regression affecting amdgpu users due to sched draining
nouveau:
- revert 6.7 deadlock fix as it has side effects
dp:
- fix documentation warning
ttm:
- fix dummy page read on some platforms
bridge:
- anx7625 suspend fix
- sii902x: fix probing and audio registration
- parade-ps8640: fix suspend of bridge, aux fixes
- samsung-dsim: avoid using FORCE_STOP_STATE
panel:
- simple add missing bus flags
- fix samsung-s6d7aa0 flags
amdgpu:
- AC/DC power supply tracking fix
- Don't show invalid vram vendor data
- SMU 13.0.x fixes
- GART fix for umr on systems without VRAM
- GFX 10/11 UNORD_DISPATCH fixes
- IPS display fixes (required for S0ix on some platforms)
- Misc fixes
i915:
- DSI sequence revert to fix GitLab #10071 and DP test-pattern fix
- Drop -Wstringop-overflow (broken on GCC11)
ivpu:
- fix recovery/reset support
- improve submit ioctl stability
- fix dev open/close races on unbind
- PLL disable reset fix
- deprecate context priority param
- improve debug buffer logging
- disable buffer sharing across VPU contexts
- free buffer sgt on unbind
- fix missing lock around shmem vmap
- add better boot diagnostics
- add more debug prints around mapping
- dump MMU events in case of timeout
v3d:
- NULL ptr dereference fix
exynos:
- fix stack usage
- fix incorrect type
- fix dt typo
- fix gsc runtime resume
xe:
- Make an ops struct static
- Fix an implicit 0 to NULL conversion
- A couple of 32-bit fixes
- A migration coherency fix for Lunar Lake.
- An error path vm id leak fix
- Remove PVC references in kunit tests"
* tag 'drm-fixes-2024-01-27' of git://anongit.freedesktop.org/drm/drm: (66 commits)
Revert "nouveau: push event block/allowing out of the fence context"
drm: bridge: samsung-dsim: Don't use FORCE_STOP_STATE
drm/sched: Drain all entities in DRM sched run job worker
drm/amd/display: "Enable IPS by default"
drm/amd: Add a DC debug mask for IPS
drm/amd/display: Disable ips before dc interrupt setting
drm/amd/display: Replay + IPS + ABM in Full Screen VPB
drm/amd/display: Add IPS checks before dcn register access
drm/amd/display: Add Replay IPS register for DMUB command table
drm/amd/display: Allow IPS2 during Replay
drm/amdgpu/gfx11: set UNORD_DISPATCH in compute MQDs
drm/amdgpu/gfx10: set UNORD_DISPATCH in compute MQDs
drm/amd/amdgpu: Assign GART pages to AMD device mapping
drm/amd/pm: Fetch current power limit from FW
drm/amdgpu: Fix null pointer dereference
drm/amdgpu: Show vram vendor only if available
drm/amd/pm: update the power cap setting
drm/amdgpu: Avoid fetching vram vendor information
drm/amdgpu/pm: Fix the power source flag error
drm/amd/display: Fix uninitialized variable usage in core_link_ 'read_dpcd() & write_dpcd()' functions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic update from Arnd Bergmann:
"Just one patch this time, adding Andreas Larsson as co-maintainer for
arch/sparc. He is volunteering to help since David Miller has become
much less active over the past few years.
In turn, I'm helping Andreas get set up as a new maintainer, starting
with the entry in the MAINTAINERS file"
* tag 'asm-generic-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
MAINTAINERS: Add Andreas Larsson as co-maintainer for arch/sparc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull arm SoC fixes from Arnd Bergmann:
"There are a couple of devicetree fixes for samsung, riscv/sophgo, and
for TPM device nodes on a couple of platforms.
Both the Arm FF-A and the SCMI firmware drivers get a number of code
fixes, addressing minor implementation bugs and compatibility with
firmware implementations. Most of these bugs relate to the usage of
xarray and rwlock structures and are fixed by Cristian Marussi"
* tag 'arm-fixes-6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
riscv: dts: sophgo: separate sg2042 mtime and mtimecmp to fit aclint format
arm64: dts: Fix TPM schema violations
ARM: dts: Fix TPM schema violations
ARM: dts: exynos4212-tab3: add samsung,invert-vclk flag to fimd
arm64: dts: exynos: gs101: comply with the new cmu_misc clock names
firmware: arm_ffa: Handle partitions setup failures
firmware: arm_ffa: Use xa_insert() and check for result
firmware: arm_ffa: Simplify ffa_partitions_cleanup()
firmware: arm_ffa: Check xa_load() return value
firmware: arm_ffa: Add missing rwlock_init() for the driver partition
firmware: arm_ffa: Add missing rwlock_init() in ffa_setup_partitions()
firmware: arm_scmi: Fix the clock protocol supported version
firmware: arm_scmi: Fix the clock protocol version for v3.2
firmware: arm_scmi: Use xa_insert() when saving raw queues
firmware: arm_scmi: Use xa_insert() to store opps
firmware: arm_scmi: Replace asm-generic/bug.h with linux/bug.h
firmware: arm_scmi: Check mailbox/SMT channel for consistency
|
