| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- btusb: Add new VID/PID 13d3/3610 for MT7922
- btusb: Add new VID/PID 13d3/3628 for MT7925
- btusb: Add MT7921e device 13d3:3576
- btusb: Add RTL8851BE device 13d3:3600
- btusb: Add ID 0x2c7c:0x0130 for Qualcomm WCN785x
- btusb: add sysfs attribute to control USB alt setting
- qca: Expand firmware-name property
- qca: Fix poor RF performance for WCN6855
- L2CAP: handle NULL sock pointer in l2cap_sock_alloc
- Allow reset via sysfs
- ISO: Allow BIG re-sync
- dt-bindings: Utilize PMU abstraction for WCN6750
- MGMT: Mark LL Privacy as stable
* tag 'for-net-next-2025-01-15' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (23 commits)
Bluetooth: MGMT: Fix slab-use-after-free Read in mgmt_remove_adv_monitor_sync
Bluetooth: qca: Fix poor RF performance for WCN6855
Bluetooth: Allow reset via sysfs
Bluetooth: Get rid of cmd_timeout and use the reset callback
Bluetooth: Remove the cmd timeout count in btusb
Bluetooth: Use str_enable_disable-like helpers
Bluetooth: btmtk: Remove resetting mt7921 before downloading the fw
Bluetooth: L2CAP: handle NULL sock pointer in l2cap_sock_alloc
Bluetooth: btusb: Add RTL8851BE device 13d3:3600
dt-bindings: bluetooth: Utilize PMU abstraction for WCN6750
Bluetooth: btusb: Add MT7921e device 13d3:3576
Bluetooth: btrtl: check for NULL in btrtl_setup_realtek()
Bluetooth: btbcm: Fix NULL deref in btbcm_get_board_name()
Bluetooth: qca: Expand firmware-name to load specific rampatch
Bluetooth: qca: Update firmware-name to support board specific nvm
dt-bindings: net: bluetooth: qca: Expand firmware-name property
Bluetooth: btusb: Add new VID/PID 13d3/3628 for MT7925
Bluetooth: btusb: Add new VID/PID 13d3/3610 for MT7922
Bluetooth: btusb: add sysfs attribute to control USB alt setting
Bluetooth: btusb: Add ID 0x2c7c:0x0130 for Qualcomm WCN785x
...
====================
Link: https://patch.msgid.link/20250117213203.3921910-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.14
Most likely the last "new features" pull request for v6.14 and this is
a bigger one. Multi-Link Operation (MLO) work continues both in stack
in drivers. Few new devices supported and usual fixes all over.
Major changes:
cfg80211
* Emergency Preparedness Communication Services (EPCS) station mode support
mac80211
* an option to filter a sta from being flushed
* some support for RX Operating Mode Indication (OMI) power saving
* support for adding and removing station links for MLO
iwlwifi
* new device ids
* rework firmware error handling and restart
rtw88
* RTL8812A: RFE type 2 support
* LED support
rtw89
* variant info to support RTL8922AE-VS
mt76
* mt7996: single wiphy multiband support (preparation for MLO)
* mt7996: support for more variants
* mt792x: P2P_DEVICE support
* mt7921u: TP-Link TXE50UH support
ath12k
* enable MLO for QCN9274 (although it seems to be broken with dual
band devices)
* MLO radar detection support
* debugfs: transmit buffer OFDMA, AST entry and puncture stats
* tag 'wireless-next-2025-01-17' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (322 commits)
wifi: brcmfmac: fix NULL pointer dereference in brcmf_txfinalize()
wifi: rtw88: add RTW88_LEDS depends on LEDS_CLASS to Kconfig
wifi: wilc1000: unregister wiphy only after netdev registration
wifi: cfg80211: adjust allocation of colocated AP data
wifi: mac80211: fix memory leak in ieee80211_mgd_assoc_ml_reconf()
wifi: ath12k: fix key cache handling
wifi: ath12k: Fix uninitialized variable access in ath12k_mac_allocate() function
wifi: ath12k: Remove ath12k_get_num_hw() helper function
wifi: ath12k: Refactor the ath12k_hw get helper function argument
wifi: ath12k: Refactor ath12k_hw set helper function argument
wifi: mt76: mt7996: add implicit beamforming support for mt7992
wifi: mt76: mt7996: fix beacon command during disabling
wifi: mt76: mt7996: fix ldpc setting
wifi: mt76: mt7996: fix definition of tx descriptor
wifi: mt76: connac: adjust phy capabilities based on band constraints
wifi: mt76: mt7996: fix incorrect indexing of MIB FW event
wifi: mt76: mt7996: fix HE Phy capability
wifi: mt76: mt7996: fix the capability of reception of EHT MU PPDU
wifi: mt76: mt7996: add max mpdu len capability
wifi: mt76: mt7921: avoid undesired changes of the preset regulatory domain
...
====================
Link: https://patch.msgid.link/20250117203529.72D45C4CEDD@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After 1b23cdbd2bbc ("net: protect netdev->napi_list with netdev_lock()")
it makes sense to iterate through dev->napi_list while holding
the device lock.
Also call synchronize_net() at most one time.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250117232113.1612899-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have some leftovers from the switch to linkmode bitmaps which
- have never been used
- are not used any longer
- have no user outside phy_device.c
So remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/5493b96e-88bb-4230-a911-322659ec5167@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot complained that free_netdev() was calling netif_napi_del()
after dev->lock mutex has been destroyed.
This fires a warning for CONFIG_DEBUG_MUTEXES=y builds.
Move mutex_destroy(&dev->lock) near the end of free_netdev().
[1]
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 0 PID: 5971 at kernel/locking/mutex.c:564 __mutex_lock_common kernel/locking/mutex.c:564 [inline]
WARNING: CPU: 0 PID: 5971 at kernel/locking/mutex.c:564 __mutex_lock+0xdac/0xee0 kernel/locking/mutex.c:735
Modules linked in:
CPU: 0 UID: 0 PID: 5971 Comm: syz-executor Not tainted 6.13.0-rc7-syzkaller-01131-g8d20dcda404d #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 12/27/2024
RIP: 0010:__mutex_lock_common kernel/locking/mutex.c:564 [inline]
RIP: 0010:__mutex_lock+0xdac/0xee0 kernel/locking/mutex.c:735
Code: 0f b6 04 38 84 c0 0f 85 1a 01 00 00 83 3d 6f 40 4c 04 00 75 19 90 48 c7 c7 60 84 0a 8c 48 c7 c6 00 85 0a 8c e8 f5 dc 91 f5 90 <0f> 0b 90 90 90 e9 c7 f3 ff ff 90 0f 0b 90 e9 29 f8 ff ff 90 0f 0b
RSP: 0018:ffffc90003317580 EFLAGS: 00010246
RAX: ee0f97edaf7b7d00 RBX: ffff8880299f8cb0 RCX: ffff8880323c9e00
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffffc90003317710 R08: ffffffff81602ac2 R09: 1ffff110170c519a
R10: dffffc0000000000 R11: ffffed10170c519b R12: 0000000000000000
R13: 0000000000000000 R14: 1ffff92000662ec4 R15: dffffc0000000000
FS: 000055557a046500(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd581d46ff8 CR3: 000000006f870000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
netdev_lock include/linux/netdevice.h:2691 [inline]
__netif_napi_del include/linux/netdevice.h:2829 [inline]
netif_napi_del include/linux/netdevice.h:2848 [inline]
free_netdev+0x2d9/0x610 net/core/dev.c:11621
netdev_run_todo+0xf21/0x10d0 net/core/dev.c:11189
nsim_destroy+0x3c3/0x620 drivers/net/netdevsim/netdev.c:1028
__nsim_dev_port_del+0x14b/0x1b0 drivers/net/netdevsim/dev.c:1428
nsim_dev_port_del_all drivers/net/netdevsim/dev.c:1440 [inline]
nsim_dev_reload_destroy+0x28a/0x490 drivers/net/netdevsim/dev.c:1661
nsim_drv_remove+0x58/0x160 drivers/net/netdevsim/dev.c:1676
device_remove drivers/base/dd.c:567 [inline]
Fixes: 1b23cdbd2bbc ("net: protect netdev->napi_list with netdev_lock()")
Reported-by: syzbot+85ff1051228a04613a32@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/678add43.050a0220.303755.0016.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250117224626.1427577-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds with gcc 14.2.1 report:
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:4193:32: error: ‘%s’ directive output may be truncated writing up to 31 bytes into a region of size 27 [-Werror=format-truncation=]
4193 | "/pkg %s", buf);
It's upset that we let buf be full length but then we use 5
characters for "/pkg ".
The builds is also clear with clang version 19.1.5 now.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250117183726.1481524-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The number of SYN + MPC retransmissions before falling back to TCP was
fixed to 2. This is certainly a good default value, but having a fixed
number can be a problem in some environments.
The current behaviour means that if all packets are dropped, there will
be:
- The initial SYN + MPC
- 2 retransmissions with MPC
- The next ones will be without MPTCP.
So typically ~3 seconds before falling back to TCP. In some networks
where some temporally blackholes are unfortunately frequent, or when a
client tries to initiate connections while the network is not ready yet,
this can cause new connections not to have MPTCP connections.
In such environments, it is now possible to increase the number of SYN
retransmissions with MPTCP options to make sure MPTCP is used.
Interesting values are:
- 0: the first retransmission will be done without MPTCP options: quite
aggressive, but also a higher risk of detecting false-positive
MPTCP blackholes.
- >= 128: all SYN retransmissions will keep the MPTCP options: back to
the < 6.12 behaviour.
The default behaviour is not changed here.
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250117-net-next-mptcp-syn_retrans_before_tcp_fallback-v1-1-ab4b187099b0@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sean Anderson says:
====================
net: xilinx: axienet: Report an error for bad coalesce settings
====================
Link: https://patch.msgid.link/20250116232954.2696930-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Instead of silently ignoring invalid/unsupported settings, report an
error. Additionally, relax the check for non-zero usecs to apply only
when it will be used (i.e. when frames != 1).
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://patch.msgid.link/20250116232954.2696930-3-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Instead of using literals, add some symbolic constants for the IRQ delay
timer calculation.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://patch.msgid.link/20250116232954.2696930-2-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update header inclusions to follow IWYU (Include What You Use)
principle.
In this case replace of_gpio.h, which is subject to remove by the GPIOLIB
subsystem, with the respective headers that are being used by the driver.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250116153119.148097-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove. The drivers in question
don't use it, simply remove the unused header.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Vladimir Oltean says:
====================
ethtool get_ts_stats() for DSA and ocelot driver
After a recent patch set with fixes and general restructuring, Jakub asked
for the Felix DSA driver to start reporting standardized statistics
for hardware timestamping:
https://lore.kernel.org/netdev/20241207180640.12da60ed@kernel.org/
Testing follows the same procedure as in the aforementioned series, with PTP
packet loss induced through taprio:
$ ethtool -I --show-time-stamping swp3
Time stamping parameters for swp3:
Capabilities:
hardware-transmit
software-transmit
hardware-receive
software-receive
software-system-clock
hardware-raw-clock
PTP Hardware Clock: 1
Hardware Transmit Timestamp Modes:
off
on
onestep-sync
Hardware Receive Filter Modes:
none
ptpv2-l4-event
ptpv2-l2-event
ptpv2-event
Statistics:
tx_pkts: 14591
tx_lost: 85
tx_err: 0
v1: https://lore.kernel.org/20241213140852.1254063-1-vladimir.oltean@nxp.com/
====================
Link: https://patch.msgid.link/20250116104628.123555-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make the linkage between the DSA user port ethtool_ops :: get_ts_info
and the implementation from the Ocelot switch library.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250116104628.123555-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add an u64 hardware timestamping statistics structure for each ocelot
port. Export a function from the common switch library for reporting
them to ethtool. This is called by the ocelot switchdev front-end for
now.
Note that for the switchdev driver, we report the one-step PTP packets
as unconfirmed, even though in principle, for some transmission
mechanisms like FDMA, we may be able to confirm transmission and bump
the "pkts" counter in ocelot_fdma_tx_cleanup() instead. I don't have
access to hardware which uses the switchdev front-end, and I've kept the
implementation simple.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250116104628.123555-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Integrate with the standard infrastructure for reporting hardware packet
timestamping statistics.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250116104628.123555-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For packets with two-step timestamp requests, the hardware timestamp
comes back to the driver through a confirmation mechanism of sorts,
which allows the driver to confidently bump the successful "pkts"
counter.
For one-step PTP, the NIC is supposed to autonomously insert its
hardware TX timestamp in the packet headers while simultaneously
transmitting it. There may be a confirmation that this was done
successfully, or there may not.
None of the current drivers which implement ethtool_ops :: get_ts_stats()
also support HWTSTAMP_TX_ONESTEP_SYNC or HWTSTAMP_TX_ONESTEP_SYNC, so it
is a bit unclear which model to follow. But there are NICs, such as DSA,
where there is no transmit confirmation at all. Here, it would be wrong /
misleading to increment the successful "pkts" counter, because one-step
PTP packets can be dropped on TX just like any other packets.
So introduce a special counter which signifies "yes, an attempt was made,
but we don't know whether it also exited the port or not". I expect that
for one-step PTP packets where a confirmation is available, the "pkts"
counter would be bumped.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250116104628.123555-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Petr Machata says:
====================
mlxsw: Move Tx header handling to PCI driver
Amit Cohen writes:
Tx header should be added to all packets transmitted from the CPU to
Spectrum ASICs. Historically, handling this header was added as a driver
function, as Tx header is different between Spectrum and Switch-X.
From May 2021, there is no support for SwitchX-2 ASIC, and all the relevant
code was removed.
For now, there is no justification to handle Tx header as part of
spectrum.c, we can handle this as part of PCI, in skb_transmit().
This change will also be useful when XDP support will be added to mlxsw,
as for XDP_TX and XDP_REDIRECT actions, Tx header should be added before
transmitting the packet.
Patch set overview:
Patches #1-#2 add structure to store Tx header info and initialize it
Patch #3 moves definitions of Tx header fields to txheader.h
Patch #4 moves Tx header handling to PCI driver
Patch #5 removes unnecessary attribute
====================
Link: https://patch.msgid.link/cover.1737044384.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tx header handling was moved to PCI code, as there is no several drivers
which configure Tx header differently. Tx header length is stored as driver
parameter, this is not really necessary as it always stores the same value.
Remove this field and use the macro MLXSW_TXHDR_LEN explicitly.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/1fb7b3f007de4d311e559c8a954b673d0895d5e9.1737044384.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tx header should be added to all packets transmitted from the CPU to
Spectrum ASICs. Historically, handling this header was added as a driver
function, as Tx header is different between Spectrum and Switch-X. See
SwitchX implementation in commit 31557f0f9755 ("mlxsw: Introduce
Mellanox SwitchX-2 ASIC support"). From May 2021, there is no support
for SwitchX-2 ASIC, and all the relevant code was removed.
For now, there is no justification to handle Tx header as part of
spectrum.c, we can handle this as part of PCI, in skb_transmit().
A future patch set will add support for XDP in mlxsw driver, to support
XDP_TX and XDP_REDIRECT actions, Tx header should be added before
transmitting the packet. As preparation for this, move Tx header handling
to PCI driver, so then XDP code will not have to call API from spectrum.c.
This also improves the code as now Tx header is pushed just before
transmitting, so it is not done from many flows which might miss something.
Note that for PTP, we should configure Tx header differently, use the
fields from mlxsw_txhdr_info to configure the packets correctly in PCI
driver. Handle VLAN tagging in switch driver, verify that packet which
should be transmitted as data is tagged, otherwise, tag it.
Remove the calls for thxdr_construct() functions, as now this is done as
part of skb_transmit().
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/293a81e6f7d59a8ec9f9592edb7745536649ff11.1737044384.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The next patch will move Tx header constructing to pci.c. As preparation,
move the definitions of Tx header fields from spectrum.c to txheader.h,
so pci.c will include this header and can access the fields.
Remove 'etclass' which is not used.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/2250b5cb3998ab4850fc8251c3a0f5926d32e194.1737044384.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A next patch will construct Tx header as part of pci.c. The switch driver
(mlxsw_spectrum.ko) should encapsulate all the differences between the
different ASICs and the bus driver (mlxsw_pci.ko) should remain unaware.
As preparation, add the relevant info as part of mlxsw_txhdr_info
structure, so later bus driver will merely construct the Tx header based on
information passed from the switch driver.
Most of the packets are transmitted as control packets, but PTP packets in
Spectrum-2 and Spectrum-3 should be handled differently. The driver
transmits them as data packets, and the default VLAN tag (4095) is added if
the packet is not already tagged.
Extend PTP operations to store a boolean which indicates whether packets
should be transmitted as data packets. Set it for Spectrum-2 and
Spectrum-3 only. Extend mlxsw_txhdr_info to store fields which will be used
later to construct Tx header. Initialize such fields according to the new
boolean which is stored in PTP operations.
Note that for now, mlxsw_txhdr_info structure is initialized, but not used,
a next patch will use it.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/efcaacd4bedef524e840a0c29f96cebf2c4bc0e0.1737044384.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mlxsw_tx_info structure is used to store information that is needed to
process Tx completions when Tx time stamps are requested. A next patch
will move Tx header handling from spectrum.c to pci.c. For that, some
additional fields which are related to Tx should be passed to pci driver.
As preparation, create an extended structure, called mlxsw_txhdr_info,
and store mlxsw_tx_info inside. The new fields should not be added to
mlxsw_tx_info structure as it is stored in the SKB control block which is
of limited size.
The next patch will extend the new structure with some fields which are
needed in order to construct Tx header.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/93aed1961f046f79f46869bab37a3faa5027751d.1737044384.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Shifting dest_attr->vport.vhca_id << 16 results in a promotion from an
unsigned 16 bit integer to a 32 bit signed integer, this is then sign
extended to a 64 bit unsigned long on 64 bitarchitectures. If vhca_id is
greater than 0x7fff then this leads to a sign extended result where all
the upper 32 bits of idx are set to 1. Fix this by casting vhca_id
to the same type as idx before performing the shift.
Fixes: 8e2e08a6d1e0 ("net/mlx5: fs, add support for dest vport HWS action")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Moshe Shemesh <moshe@nvidia.com>
Link: https://patch.msgid.link/20250116181700.96437-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The existing error message ("Invalid qdisc name") is confusing
because it suggests that there is no qdisc with the given name. In
fact, the name does refer to a valid qdisc, but it doesn't match
the kind of an existing qdisc being modified or replaced. The
new error message provides more detail to eliminate confusion.
Signed-off-by: John Ousterhout <ouster@cs.stanford.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20250116195642.2794-1-ouster@cs.stanford.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
ice: support FW Recovery Mode
Konrad Knitter says:
Enable update of card in FW Recovery Mode
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: support FW Recovery Mode
devlink: add devl guard
pldmfw: enable selected component update
====================
Link: https://patch.msgid.link/20250116212059.1254349-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace the deprecated one-element array with a modern flexible array
member in the struct nvsp_1_message_send_receive_buffer_complete.
Use struct_size_t(,,1) instead of sizeof() to maintain the same size.
Compile-tested only.
Link: https://github.com/KSPP/linux/issues/79
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Tested-by: Roman Kisel <romank@linux.microsoft.com>
Reviewed-by: Roman Kisel <romank@linux.microsoft.com>
Link: https://patch.msgid.link/20250116211932.139564-2-thorsten.blum@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use inet_sk_dscp() to get the socket DSCP value as dscp_t, instead of
ip_sock_rt_tos() which returns a __u8. This will ease the conversion
of fl4->flowi4_tos to dscp_t, which now just becomes a matter of
dropping the inet_dscp_to_dsfield() call.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/06bdb310a075355ff059cd32da2efc29a63981c9.1737034675.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use inet_sk_dscp() to get the socket DSCP value as dscp_t, instead of
ip_sock_rt_tos() which returns a __u8. This will ease the conversion
of fl4->flowi4_tos to dscp_t, which now just becomes a matter of
dropping the inet_dscp_to_dsfield() call.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/208dc5ca28bb5595d7a545de026bba18b1d63bda.1737032802.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit b9d5f5711dd8 ("selftests: net: increase the delay for relative
cmsg_time.sh test") widened the accepted value range 8x but we still
see flakes (at a rate of around 7%).
Return XFAIL for the most timing sensitive test on slow machines.
Before:
# ./cmsg_time.sh
Case UDPv4 - TXTIME rel returned '8074us - 7397us < 4000', expected 'OK'
FAIL - 1/36 cases failed
After:
# ./cmsg_time.sh
Case UDPv4 - TXTIME rel returned '1123us - 941us < 500', expected 'OK' (XFAIL)
Case UDPv6 - TXTIME rel returned '1227us - 776us < 500', expected 'OK' (XFAIL)
OK
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250116020105.931338-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reduce duplicate code by using netlink helpers which return the
soft/hard interface directly. Instead of returning an interface index
which we are typically not interested in.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Divya Koppera says:
====================
Add PEROUT library for RDS PTP supported phys
Adds support for PEROUT library, where phy can generate
periodic output signal on supported pin out.
====================
Link: https://patch.msgid.link/20250115090634.12941-1-divya.koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
supported Microchip phys
Adds PEROUT feature for RDS PTP supported phys where
we can generate periodic output signal on supported
pin out
Signed-off-by: Divya Koppera <divya.koppera@microchip.com>
Link: https://patch.msgid.link/20250115090634.12941-4-divya.koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adds support for enabling pin out that is required
to generate periodic output signal on lan887x phy.
Signed-off-by: Divya Koppera <divya.koppera@microchip.com>
Link: https://patch.msgid.link/20250115090634.12941-3-divya.koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This ptp header file library changes will cover PEROUT
macros that are required to generate periodic output
from pin out
Signed-off-by: Divya Koppera <divya.koppera@microchip.com>
Link: https://patch.msgid.link/20250115090634.12941-2-divya.koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The following tests are failing on debug kernels:
tcp_tcp_info_tcp-info-rwnd-limited.pkt
tcp_tcp_info_tcp-info-sndbuf-limited.pkt
with reports like:
assert 19000 <= tcpi_sndbuf_limited <= 21000, tcpi_sndbuf_limited; \
AssertionError: 18000
and:
assert 348000 <= tcpi_busy_time <= 360000, tcpi_busy_time
AssertionError: 362000
Extend commit 912d6f669725 ("selftests/net: packetdrill: report benign
debug flakes as xfail") to cover them.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250115232129.845884-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Russell King says:
====================
net: add phylink managed EEE support
Adding managed EEE support to phylink has been on the cards ever since
the idea in phylib was mooted. This overly large series attempts to do
so. I've included all the patches as it's important to get the driver
patches out there.
Patch 1 adds a definition for the clock stop capable bit in the PCS
MMD status register.
Patch 2 adds a phylib API to query whether the PHY allows the transmit
xMII clock to be stopped while in LPI mode. This capability is for MAC
drivers to save power when LPI is active, to allow them to stop their
transmit clock.
Patch 3 extracts a phylink internal helper for determining whether the
link is up.
Patch 4 adds basic phylink managed EEE support. Two new MAC APIs are
added, to enable and disable LPI. The enable method is passed the LPI
timer setting which it is expected to program into the hardware, and
also a flag ehther the transmit clock should be stopped.
I have taken the decision to make enable_tx_lpi() to return an error
code, but not do much with it other than report it - the intention
being that we can later use it to extend functionality if needed
without reworking loads of drivers.
I have also dropped the validation/limitation of the LPI timer, and
left that in the driver code prior to calling phylink_ethtool_set_eee().
The remainder of the patches convert mvneta, lan743x and stmmac, and
add support for mvneta.
====================
Link: https://patch.msgid.link/Z4gdtOaGsBhQCZXn@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert stmmac to use phylink managed EEE support rather than delving
into phylib:
1. Move the stmmac_eee_init() calls out of mac_link_down() and
mac_link_up() methods into the new mac_{enable,disable}_lpi()
methods. We leave the calls to stmmac_set_eee_pls() in place as
these change bits which tell the EEE hardware when the link came
up or down, and is used for a separate hardware timer. However,
symmetrically conditionalise this with priv->dma_cap.eee.
2. Update the current LPI timer each time LPI is enabled - which we
need for software-timed LPI.
3. With phylink managed EEE, phylink manages the receive clock stop
configuration via phylink_config.eee_rx_clk_stop_enable. Set this
appropriately which makes the call to phy_eee_rx_clock_stop()
redundant.
4. From what I can work out, all supported interfaces support LPI
signalling on stmmac (there's no restriction implemented.) It
also appears to support LPI at all full duplex speeds at or over
100M. Set these capabilities.
5. The default timer appears to be derived from a module parameter.
Set this the same, although we keep code that reconfigures the
timer in stmmac_init_phy().
6. Remove the direct call to phy_support_eee(), which phylink will do
on the drivers behalf if phylink_config.eee_enabled_default is set.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYAEG-0014QH-9O@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert lan743x to phylink managed EEE:
- Set the lpi_capabilties.
- Move the call to lan743x_mac_eee_enable() into the enable/disable
tx_lpi functions.
- Ensure that EEEEN is clear during probe.
- Move the setting of the LPI timer into mac_enable_tx_lpi().
- Move reading of LPI timer to phylink initialisation to set the
default timer value.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYAEB-0014QB-4s@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the netdev that we already have in lan743x_phylink_mac_link_down().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYAE5-0014Q5-Up@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add EEE support for mvpp2, using phylink's EEE implementation, which
means we just need to implement the two methods for LPI control, and
with the initial configuration. Only SGMII mode is supported, so only
100M and 1G speeds.
Disabling LPI requires clearing a single bit. Enabling LPI needs a full
configuration of several values, as the timer values are dependent on
the MAC operating speed.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYAE0-0014Pz-R9@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert mvneta to use phylink's EEE implementation by implementing the
two LPI control methods, and adding the initial configuration and
capabilities.
Although disabling LPI requires clearing a single bit, for safety we
clear the manual mode and force bits to ensure that auto mode will be
used.
Enabling LPI needs a full configuration of several values, as the timer
values are dependent on the MAC operating speed, as per the original
code.
As Armada 388 states that EEE is only supported in "SGMII" modes, mark
this in lpi_interfaces. Testing with RGMII on the Clearfog platform
indicates that the receive path fails to detect LPI over RGMII.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYADv-0014Pt-NO@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add EEE management to phylink, making use of the phylib implementation.
This will only be used where a MAC driver populates the methods and
capabilities bitfield, otherwise we keep our old behaviour.
Phylink will keep track of the EEE configuration, including the clock
stop abilities at each end of the MAC to PHY link, programming the PHY
appropriately and preserving the LPI configuration should the PHY go
away.
Phylink will call into the MAC driver when LPI needs to be enabled or
disabled, with the requirement that the MAC have LPI disabled prior
to the netdev being brought up (in other words, it will only call
mac_disable_tx_lpi() if it has already called mac_enable_tx_lpi().)
Support for phylink managed EEE is enabled by populating both tx_lpi
MAC operations method pointers, and filling in both LPI interfaces
and capabilities. If the methods are provided but the LPI interfaces
or capabilities remain empty, this indicates to phylink that EEE is
implemented by the driver but the hardware it is driving does not
support EEE, and thus the ethtool set_eee() and get_eee() methods will
return EOPNOTSUPP.
No validation of the LPI timer value is performed by this patch.
For interface modes which do not support LPI, we make no attempt to
manipulate the phylib EEE advertisement, but instead refuse to
activate LPI at the MAC, noting it at debug message level.
We also restrict the advertisement and reported userspace support
linkmode masks according to the lpi_capabilities provided to
phylink by the MAC driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYADq-0014Pn-J1@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a helper to determine whether the link is up or down. Currently
this is only used in one location, but becomes necessary to test
when reconfiguring EEE.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYADl-0014Ph-EV@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for querying whether the PHY allows the transmit xMII clock
to be stopped while in LPI mode. This will be used by phylink to pass
to the MAC driver so it can configure the generation of the xMII clock
appropriately.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYADg-0014Pb-AJ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a definition for the clock stop capable bit in the PCS MMD. This
bit indicates whether the MAC is able to stop the transmit xMII clock
while it is signalling LPI.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1tYADb-0014PV-6T@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Kuniyuki Iwashima says:
====================
dev: Covnert dev_change_name() to per-netns RTNL.
Patch 1 adds a missing netdev_rename_lock in dev_change_name()
and Patch 2 removes unnecessary devnet_rename_sem there.
Patch 3 replaces RTNL with rtnl_net_lock() in dev_ifsioc(),
and now dev_change_name() is always called under per-netns RTNL.
Given it's close to -rc8 and Patch 1 touches the trivial unlikely
path, can Patch 1 go into net-next ? Otherwise I'll post Patch 2 & 3
separately in the next cycle.
====================
Link: https://patch.msgid.link/20250115095545.52709-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Basically, dev_ifsioc() operates on the passed single netns (except
for netdev notifier chains with lower/upper devices for which we will
need more changes).
Let's hold rtnl_net_lock() for dev_ifsioc().
Now that NETDEV_CHANGENAME is always triggered under rtnl_net_lock()
of the device's netns. (do_setlink() and dev_ifsioc())
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250115095545.52709-4-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
devnet_rename_sem is no longer used since commit
0840556e5a3a ("net: Protect dev->name by seqlock.").
Also, RTNL serialises dev_change_name().
Let's remove devnet_rename_sem.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250115095545.52709-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The cited commit forgot to add netdev_rename_lock in one of the
error paths in dev_change_name().
Let's hold netdev_rename_lock before restoring the old dev->name.
Fixes: 0840556e5a3a ("net: Protect dev->name by seqlock.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250115095545.52709-2-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
