| Age | Commit message (Collapse) | Author |
|---|
|
An issue was present in the initial driver implementation. The driver
read the power status of all channels before toggling the bit of the
desired one. Using the power status register as a base value introduced
a problem, because only the bit corresponding to the concerned channel ID
should be set in the write-only power enable register. This led to cases
where disabling power for one channel also powered off other channels.
This patch removes the power status read and ensures the value is
limited to the bit matching the channel index of the PI.
Fixes: 20e6d190ffe1 ("net: pse-pd: Add TI TPS23881 PSE controller driver")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241220170400.291705-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Host Port (i.e. CPU facing port) of CPSW receives traffic from Linux
via TX DMA Channels which are Hardware Queues consisting of traffic
categorized according to their priority. The Host Port is configured to
dequeue traffic from these Hardware Queues on the basis of priority i.e.
as long as traffic exists on a Hardware Queue of a higher priority, the
traffic on Hardware Queues of lower priority isn't dequeued. An alternate
operation is also supported wherein traffic can be dequeued by the Host
Port in a Round-Robin manner.
Until commit under Fixes, the am65-cpsw driver enabled a single TX DMA
Channel, due to which, unless modified by user via "ethtool", all traffic
from Linux is transmitted on DMA Channel 0. Therefore, configuring
the Host Port for priority based dequeuing or Round-Robin operation
is identical since there is a single DMA Channel.
Since commit under Fixes, all 8 TX DMA Channels are enabled by default.
Additionally, the default "tc mapping" doesn't take into account
the possibility of different traffic profiles which various users
might have. This results in traffic starvation at the Host Port
due to the priority based dequeuing which has been enabled by default
since the inception of the driver. The traffic starvation triggers
NETDEV WATCHDOG timeout for all TX DMA Channels that haven't been serviced
due to the presence of traffic on the higher priority TX DMA Channels.
Fix this by defaulting to Round-Robin dequeuing at the Host Port, which
shall ensure that traffic is dequeued from all TX DMA Channels irrespective
of the traffic profile. This will address the NETDEV WATCHDOG timeouts.
At the same time, users can still switch from Round-Robin to Priority
based dequeuing at the Host Port with the help of the "p0-rx-ptype-rrobin"
private flag of "ethtool". Users are expected to setup an appropriate
"tc mapping" that suits their traffic profile when switching to priority
based dequeuing at the Host Port.
Fixes: be397ea3473d ("net: ethernet: am65-cpsw: Set default TX channels to maximum")
Cc: <stable@vger.kernel.org>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20241220075618.228202-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While by default max_autoclose equals to INT_MAX / HZ, one may set
net.sctp.max_autoclose to UINT_MAX. There is code in
sctp_association_init() that can consequently trigger overflow.
Cc: stable@vger.kernel.org
Fixes: 9f70f46bd4c7 ("sctp: properly latch and use autoclose value from sock to association")
Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20241219162114.2863827-1-kniv@yandex-team.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Syzkaller reports an uninit value read from ax25cmp when sending raw message
through ieee802154 implementation.
=====================================================
BUG: KMSAN: uninit-value in ax25cmp+0x3a5/0x460 net/ax25/ax25_addr.c:119
ax25cmp+0x3a5/0x460 net/ax25/ax25_addr.c:119
nr_dev_get+0x20e/0x450 net/netrom/nr_route.c:601
nr_route_frame+0x1a2/0xfc0 net/netrom/nr_route.c:774
nr_xmit+0x5a/0x1c0 net/netrom/nr_dev.c:144
__netdev_start_xmit include/linux/netdevice.h:4940 [inline]
netdev_start_xmit include/linux/netdevice.h:4954 [inline]
xmit_one net/core/dev.c:3548 [inline]
dev_hard_start_xmit+0x247/0xa10 net/core/dev.c:3564
__dev_queue_xmit+0x33b8/0x5130 net/core/dev.c:4349
dev_queue_xmit include/linux/netdevice.h:3134 [inline]
raw_sendmsg+0x654/0xc10 net/ieee802154/socket.c:299
ieee802154_sock_sendmsg+0x91/0xc0 net/ieee802154/socket.c:96
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg net/socket.c:745 [inline]
____sys_sendmsg+0x9c2/0xd60 net/socket.c:2584
___sys_sendmsg+0x28d/0x3c0 net/socket.c:2638
__sys_sendmsg net/socket.c:2667 [inline]
__do_sys_sendmsg net/socket.c:2676 [inline]
__se_sys_sendmsg net/socket.c:2674 [inline]
__x64_sys_sendmsg+0x307/0x490 net/socket.c:2674
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x44/0x110 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Uninit was created at:
slab_post_alloc_hook+0x129/0xa70 mm/slab.h:768
slab_alloc_node mm/slub.c:3478 [inline]
kmem_cache_alloc_node+0x5e9/0xb10 mm/slub.c:3523
kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:560
__alloc_skb+0x318/0x740 net/core/skbuff.c:651
alloc_skb include/linux/skbuff.h:1286 [inline]
alloc_skb_with_frags+0xc8/0xbd0 net/core/skbuff.c:6334
sock_alloc_send_pskb+0xa80/0xbf0 net/core/sock.c:2780
sock_alloc_send_skb include/net/sock.h:1884 [inline]
raw_sendmsg+0x36d/0xc10 net/ieee802154/socket.c:282
ieee802154_sock_sendmsg+0x91/0xc0 net/ieee802154/socket.c:96
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg net/socket.c:745 [inline]
____sys_sendmsg+0x9c2/0xd60 net/socket.c:2584
___sys_sendmsg+0x28d/0x3c0 net/socket.c:2638
__sys_sendmsg net/socket.c:2667 [inline]
__do_sys_sendmsg net/socket.c:2676 [inline]
__se_sys_sendmsg net/socket.c:2674 [inline]
__x64_sys_sendmsg+0x307/0x490 net/socket.c:2674
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x44/0x110 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x63/0x6b
CPU: 0 PID: 5037 Comm: syz-executor166 Not tainted 6.7.0-rc7-syzkaller-00003-gfbafc3e621c3 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023
=====================================================
This issue occurs because the skb buffer is too small, and it's actual
allocation is aligned. This hides an actual issue, which is that nr_route_frame
does not validate the buffer size before using it.
Fix this issue by checking skb->len before accessing any fields in skb->data.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Co-developed-by: Nikita Marushkin <hfggklm@gmail.com>
Signed-off-by: Nikita Marushkin <hfggklm@gmail.com>
Signed-off-by: Ilya Shchipletsov <rabbelkin@mail.ru>
Link: https://patch.msgid.link/20241219082308.3942-1-rabbelkin@mail.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The device denoted by tunnel->parms.link resides in the underlay net
namespace. Therefore pass tunnel->net to ip_tunnel_init_flow().
Fixes: db53cd3d88dc ("net: Handle l3mdev in ip_tunnel_init_flow")
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20241219130336.103839-1-shaw.leon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If inet_csk_reqsk_queue_hash_add() return false, tcp_conn_request() will
return without free the dst memory, which allocated in af_ops->route_req.
Here is the kmemleak stack:
unreferenced object 0xffff8881198631c0 (size 240):
comm "softirq", pid 0, jiffies 4299266571 (age 1802.392s)
hex dump (first 32 bytes):
00 10 9b 03 81 88 ff ff 80 98 da bc ff ff ff ff ................
81 55 18 bb ff ff ff ff 00 00 00 00 00 00 00 00 .U..............
backtrace:
[<ffffffffb93e8d4c>] kmem_cache_alloc+0x60c/0xa80
[<ffffffffba11b4c5>] dst_alloc+0x55/0x250
[<ffffffffba227bf6>] rt_dst_alloc+0x46/0x1d0
[<ffffffffba23050a>] __mkroute_output+0x29a/0xa50
[<ffffffffba23456b>] ip_route_output_key_hash+0x10b/0x240
[<ffffffffba2346bd>] ip_route_output_flow+0x1d/0x90
[<ffffffffba254855>] inet_csk_route_req+0x2c5/0x500
[<ffffffffba26b331>] tcp_conn_request+0x691/0x12c0
[<ffffffffba27bd08>] tcp_rcv_state_process+0x3c8/0x11b0
[<ffffffffba2965c6>] tcp_v4_do_rcv+0x156/0x3b0
[<ffffffffba299c98>] tcp_v4_rcv+0x1cf8/0x1d80
[<ffffffffba239656>] ip_protocol_deliver_rcu+0xf6/0x360
[<ffffffffba2399a6>] ip_local_deliver_finish+0xe6/0x1e0
[<ffffffffba239b8e>] ip_local_deliver+0xee/0x360
[<ffffffffba239ead>] ip_rcv+0xad/0x2f0
[<ffffffffba110943>] __netif_receive_skb_one_core+0x123/0x140
Call dst_release() to free the dst memory when
inet_csk_reqsk_queue_hash_add() return false in tcp_conn_request().
Fixes: ff46e3b44219 ("Fix race for duplicate reqsk on identical SYN")
Signed-off-by: Wang Liang <wangliang74@huawei.com>
Link: https://patch.msgid.link/20241219072859.3783576-1-wangliang74@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Current implementation of stmmac_probe_config_dt() does not release the
OF node reference obtained by of_parse_phandle() in some error paths.
The problem is that some error paths call stmmac_remove_config_dt() to
clean up but others use and unwind ladder. These two types of error
handling have not kept in sync and have been a recurring source of bugs.
Re-write the error handling in stmmac_probe_config_dt() to use an unwind
ladder. Consequently, stmmac_remove_config_dt() is not needed anymore,
thus remove it.
This bug was found by an experimental verification tool that I am
developing.
Fixes: 4838a5405028 ("net: stmmac: Fix wrapper drivers not detecting PHY")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Link: https://patch.msgid.link/20241219024119.2017012-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The CSR dump support leverages the FBNIC_BOUNDS macro, which pads the end
condition for each section by adding an offset of 1. However, the RPC RAM
section, which is dumped differently from other sections, does not rely
on this macro and instead directly uses end boundary address. Hence,
subtracting 1 from the end address results in skipping a register.
Fixes 3d12862b216d (“eth: fbnic: Add support to dump registers”)
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20241218232614.439329-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make sure kernel doesn't respond to GETs for queues and NAPIs when
link is down. Not with valid data, or with empty message, we want
a ENOENT.
Link: https://patch.msgid.link/20241219032833.1165433-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Empty netlink responses from do() are not correct (as opposed to
dump() where not dumping anything is perfectly fine).
We should return an error if the target object does not exist,
in this case if the netdev is down we "hide" the NAPI instances.
Fixes: 27f91aaf49b3 ("netdev-genl: Add netlink framework functions for napi")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241219032833.1165433-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the blamed commit, we require mausezahn because send_raw() uses it.
Remove the "REQUIRE_MZ=no" line, which overwrites the default of requiring it.
Fixes: 237979504264 ("selftests: net: local_termination: add PTP frames to the mix")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241219155410.1856868-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Joshua Washington says:
====================
gve: various XDP fixes
This patch series contains the following XDP fixes:
- clean up XDP tx queue when stopping rings
- use RCU synchronization to guard existence of XDP queues
- perform XSK TX as part of RX NAPI to fix busy polling
- fix XDP allocation issues when non-XDP configurations occur
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a number of consistency issues in the queue allocation
path related to XDP.
As it stands, the number of allocated XDP queues changes in three
different scenarios.
1) Adding an XDP program while the interface is up via
gve_add_xdp_queues
2) Removing an XDP program while the interface is up via
gve_remove_xdp_queues
3) After queues have been allocated and the old queue memory has been
removed in gve_queues_start.
However, the requirement for the interface to be up for
gve_(add|remove)_xdp_queues to be called, in conjunction with the fact
that the number of queues stored in priv isn't updated until _after_ XDP
queues have been allocated in the normal queue allocation path means
that if an XDP program is added while the interface is down, XDP queues
won't be added until the _second_ if_up, not the first.
Given the expectation that the number of XDP queues is equal to the
number of RX queues, scenario (3) has another problematic implication.
When changing the number of queues while an XDP program is loaded, the
number of XDP queues must be updated as well, as there is logic in the
driver (gve_xdp_tx_queue_id()) which relies on every RX queue having a
corresponding XDP TX queue. However, the number of XDP queues stored in
priv would not be updated until _after_ a close/open leading to a
mismatch in the number of XDP queues reported vs the number of XDP
queues which actually exist after the queue count update completes.
This patch remedies these issues by doing the following:
1) The allocation config getter function is set up to retrieve the
_expected_ number of XDP queues to allocate instead of relying
on the value stored in `priv` which is only updated once the queues
have been allocated.
2) When adjusting queues, XDP queues are adjusted to match the number of
RX queues when XDP is enabled. This only works in the case when
queues are live, so part (1) of the fix must still be available in
the case that queues are adjusted when there is an XDP program and
the interface is down.
Fixes: 5f08cd3d6423 ("gve: Alloc before freeing when adjusting queues")
Cc: stable@vger.kernel.org
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Shailend Chand <shailend@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When busy polling is enabled, xsk_sendmsg for AF_XDP zero copy marks
the NAPI ID corresponding to the memory pool allocated for the socket.
In GVE, this NAPI ID will never correspond to a NAPI ID of one of the
dedicated XDP TX queues registered with the umem because XDP TX is not
set up to share a NAPI with a corresponding RX queue.
This patch moves XSK TX descriptor processing from the TX NAPI to the RX
NAPI, and the gve_xsk_wakeup callback is updated to use the RX NAPI
instead of the TX NAPI, accordingly. The branch on if the wakeup is for
TX is removed, as the NAPI poll should be invoked whether the wakeup is
for TX or for RX.
Fixes: fd8e40321a12 ("gve: Add AF_XDP zero-copy support for GQI-QPL format")
Cc: stable@vger.kernel.org
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch predicates the enabling and disabling of XSK pools on the
existence of queues. As it stands, if the interface is down, disabling
or enabling XSK pools would result in a crash, as the RX queue pointer
would be NULL. XSK pool registration will occur as part of the next
interface up.
Similarly, xsk_wakeup needs be guarded against queues disappearing
while the function is executing, so a check against the
GVE_PRIV_FLAGS_NAPI_ENABLED flag is added to synchronize with the
disabling of the bit and the synchronize_net() in gve_turndown.
Fixes: fd8e40321a12 ("gve: Add AF_XDP zero-copy support for GQI-QPL format")
Cc: stable@vger.kernel.org
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Shailend Chand <shailend@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In GVE, dedicated XDP queues only exist when an XDP program is installed
and the interface is up. As such, the NDO XDP XMIT callback should
return early if either of these conditions are false.
In the case of no loaded XDP program, priv->num_xdp_queues=0 which can
cause a divide-by-zero error, and in the case of interface down,
num_xdp_queues remains untouched to persist XDP queue count for the next
interface up, but the TX pointer itself would be NULL.
The XDP xmit callback also needs to synchronize with a device
transitioning from open to close. This synchronization will happen via
the GVE_PRIV_FLAGS_NAPI_ENABLED bit along with a synchronize_net() call,
which waits for any RCU critical sections at call-time to complete.
Fixes: 39a7f4aa3e4a ("gve: Add XDP REDIRECT support for GQI-QPL format")
Cc: stable@vger.kernel.org
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Shailend Chand <shailend@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When stopping XDP TX rings, the XDP clean function needs to be called to
clean out the entire queue, similar to what happens in the normal TX
queue case. Otherwise, the FIFO won't be cleared correctly, and
xsk_tx_completed won't be reported.
Fixes: 75eaae158b1b ("gve: Add XDP DROP and TX support for GQI-QPL format")
Cc: stable@vger.kernel.org
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.13-rc5
Few minor fixes this time, nothing special.
* tag 'wireless-2024-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: cw1200: Fix potential NULL dereference
wifi: iwlwifi: mvm: Fix __counted_by usage in cfg80211_wowlan_nd_*
MAINTAINERS: wifi: ath: add Jeff Johnson as maintainer
wifi: iwlwifi: fix CRF name for Bz
====================
Link: https://patch.msgid.link/20241219185042.662B6C4CECE@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'net-dsa-microchip-fix-set_ageing_time-function-for-ksz9477-and-lan937x-switches'
Tristram Ha says:
====================
net: dsa: microchip: Fix set_ageing_time function for KSZ9477 and LAN937X switches
The aging count is not a simple number that is broken into two parts and
programmed into 2 registers. These patches correct the programming for
KSZ9477 and LAN937X switches.
====================
Link: https://patch.msgid.link/20241218020224.70590-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The aging count is not a simple 20-bit value but comprises a 3-bit
multiplier and a 20-bit second time. The code tries to use the
original multiplier which is 4 as the second count is still 300 seconds
by default.
As the 20-bit number is now too large for practical use there is an option
to interpret it as microseconds instead of seconds.
Fixes: 2c119d9982b1 ("net: dsa: microchip: add the support for set_ageing_time")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218020224.70590-3-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The aging count is not a simple 11-bit value but comprises a 3-bit
multiplier and an 8-bit second count. The code tries to use the
original multiplier which is 4 as the second count is still 300 seconds
by default.
Fixes: 2c119d9982b1 ("net: dsa: microchip: add the support for set_ageing_time")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218020224.70590-2-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On the i.MX6ULL-14x14-EVK board, enet1_ref and enet2_ref are used as the
clock sources for two external KSZ PHYs. However, after closing the two
FEC ports, the clk_enable_count of the enet1_ref and enet2_ref clocks is
not 0. The root cause is that since the commit 985329462723 ("net: phy:
micrel: use devm_clk_get_optional_enabled for the rmii-ref clock"), the
external clock of KSZ PHY has been enabled when the PHY driver probes,
and it can only be disabled when the PHY driver is removed. This causes
the clock to continue working when the system is suspended or the network
port is down.
Although Heiko explained in the commit message that the patch was because
some clock suppliers need to enable the clock to get the valid clock rate
, it seems that the simple fix is to disable the clock after getting the
clock rate to solve the current problem. This is indeed true, but we need
to admit that Heiko's patch has been applied for more than a year, and we
cannot guarantee whether there are platforms that only enable rmii-ref in
the KSZ PHY driver during this period. If this is the case, disabling
rmii-ref will cause RMII on these platforms to not work.
Secondly, commit 99ac4cbcc2a5 ("net: phy: micrel: allow usage of generic
ethernet-phy clock") just simply enables the generic clock permanently,
which seems like the generic clock may only be enabled in the PHY driver.
If we simply disable the generic clock, RMII may not work. If we keep it
as it is, the platform using the generic clock will have the same problem
as the i.MX6ULL platform.
To solve this problem, the clock is enabled when phy_driver::resume() is
called, and the clock is disabled when phy_driver::suspend() is called.
Since phy_driver::resume() and phy_driver::suspend() are not called in
pairs, an additional clk_enable flag is added. When phy_driver::suspend()
is called, the clock is disabled only if clk_enable is true. Conversely,
when phy_driver::resume() is called, the clock is enabled if clk_enable
is false.
The changes that introduced the problem were only a few lines, while the
current fix is about a hundred lines, which seems out of proportion, but
it is necessary because kszphy_probe() is used by multiple KSZ PHYs and
we need to fix all of them.
Fixes: 985329462723 ("net: phy: micrel: use devm_clk_get_optional_enabled for the rmii-ref clock")
Fixes: 99ac4cbcc2a5 ("net: phy: micrel: allow usage of generic ethernet-phy clock")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241217063500.1424011-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can and netfilter.
Current release - regressions:
- rtnetlink: try the outer netns attribute in rtnl_get_peer_net()
- rust: net::phy fix module autoloading
Current release - new code bugs:
- phy: avoid undefined behavior in *_led_polarity_set()
- eth: octeontx2-pf: fix netdev memory leak in rvu_rep_create()
Previous releases - regressions:
- smc: check sndbuf_space again after NOSPACE flag is set in smc_poll
- ipvs: fix clamp() of ip_vs_conn_tab on small memory systems
- dsa: restore dsa_software_vlan_untag() ability to operate on
VLAN-untagged traffic
- eth:
- tun: fix tun_napi_alloc_frags()
- ionic: no double destroy workqueue
- idpf: trigger SW interrupt when exiting wb_on_itr mode
- rswitch: rework ts tags management
- team: fix feature exposure when no ports are present
Previous releases - always broken:
- core: fix repeated netlink messages in queue dump
- mdiobus: fix an OF node reference leak
- smc: check iparea_offset and ipv6_prefixes_cnt when receiving
proposal msg
- can: fix missed interrupts with m_can_pci
- eth: oa_tc6: fix infinite loop error when tx credits becomes 0"
* tag 'net-6.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (45 commits)
net: mctp: handle skb cleanup on sock_queue failures
net: mdiobus: fix an OF node reference leak
octeontx2-pf: fix error handling of devlink port in rvu_rep_create()
octeontx2-pf: fix netdev memory leak in rvu_rep_create()
psample: adjust size if rate_as_probability is set
netdev-genl: avoid empty messages in queue dump
net: dsa: restore dsa_software_vlan_untag() ability to operate on VLAN-untagged traffic
selftests: openvswitch: fix tcpdump execution
net: usb: qmi_wwan: add Quectel RG255C
net: phy: avoid undefined behavior in *_led_polarity_set()
netfilter: ipset: Fix for recursive locking warning
ipvs: Fix clamp() of ip_vs_conn_tab on small memory systems
can: m_can: fix missed interrupts with m_can_pci
can: m_can: set init flag earlier in probe
rtnetlink: Try the outer netns attribute in rtnl_get_peer_net().
net: netdevsim: fix nsim_pp_hold_write()
idpf: trigger SW interrupt when exiting wb_on_itr mode
idpf: add support for SW triggered interrupts
qed: fix possible uninit pointer read in qed_mcp_nvm_info_populate()
net: ethernet: bgmac-platform: fix an OF node reference leak
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- mtk-sd: Cleanup the wakeup configuration in error/remove-path
- sdhci-tegra: Correct quirk for ADMA2 length
* tag 'mmc-v6.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mtk-sd: disable wakeup in .remove() and in the error path of .probe()
mmc: sdhci-tegra: Remove SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC quirk
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fix from Uwe Kleine-König:
"Fix regression in pwm-stm32 driver when converting to new waveform
support
Fabrice Gasnier found and fixed a regression I introduced with
v6.13-rc1 when converting the stm32 pwm driver to support the new
waveform stuff. On some hardware variants this completely broke the
driver"
* tag 'pwm/for-6.13-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: stm32: Fix complementary output in round_waveform_tohw()
|
|
Pull smb server fixes from Steve French:
- Two fixes for better handling maximum outstanding requests
- Fix simultaneous negotiate protocol race
* tag 'v6.13-rc3-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: conn lock to serialize smb2 negotiate
ksmbd: fix broken transfers when exceeding max simultaneous operations
ksmbd: count all requests in req_running counter
|
|
Currently, we don't use the return value from sock_queue_rcv_skb, which
means we may leak skbs if a message is not successfully queued to a
socket.
Instead, ensure that we're freeing the skb where the sock hasn't
otherwise taken ownership of the skb by adding checks on the
sock_queue_rcv_skb() to invoke a kfree on failure.
In doing so, rather than using the 'rc' value to trigger the
kfree_skb(), use the skb pointer itself, which is more explicit.
Also, add a kunit test for the sock delivery failure cases.
Fixes: 4a992bbd3650 ("mctp: Implement message fragmentation & reassembly")
Cc: stable@vger.kernel.org
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20241218-mctp-next-v2-1-1c1729645eaa@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
fwnode_find_mii_timestamper() calls of_parse_phandle_with_fixed_args()
but does not decrement the refcount of the obtained OF node. Add an
of_node_put() call before returning from the function.
This bug was detected by an experimental static analysis tool that I am
developing.
Fixes: bc1bee3b87ee ("net: mdiobus: Introduce fwnode_mdiobus_register_phy()")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218035106.1436405-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following series contains two fixes for Netfilter/IPVS:
1) Possible build failure in IPVS on systems with less than 512MB
memory due to incorrect use of clamp(), from David Laight.
2) Fix bogus lockdep nesting splat with ipset list:set type,
from Phil Sutter.
netfilter pull request 24-12-19
* tag 'nf-24-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: ipset: Fix for recursive locking warning
ipvs: Fix clamp() of ip_vs_conn_tab on small memory systems
====================
Link: https://patch.msgid.link/20241218234137.1687288-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Unregister the devlink port when register_netdev() fails.
Fixes: 9ed0343f561e ("octeontx2-pf: Add devlink port support")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://patch.msgid.link/20241217052326.1086191-2-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When rvu_rep_devlink_port_register() fails, free_netdev(ndev) for this
incomplete iteration before going to "exit:" label.
Fixes: 9ed0343f561e ("octeontx2-pf: Add devlink port support")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://patch.msgid.link/20241217052326.1086191-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If PSAMPLE_ATTR_SAMPLE_PROBABILITY flag is to be sent, the available
size for the packet data has to be adjusted accordingly.
Also, check the error code returned by nla_put_flag.
Fixes: 7b1b2b60c63f ("net: psample: allow using rate as probability")
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20241217113739.3929300-1-amorenoz@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Empty netlink responses from do() are not correct (as opposed to
dump() where not dumping anything is perfectly fine).
We should return an error if the target object does not exist,
in this case if the netdev is down it has no queues.
Fixes: 6b6171db7fc8 ("netdev-genl: Add netlink framework functions for queue")
Reported-by: syzbot+0a884bc2d304ce4af70f@syzkaller.appspotmail.com
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20241218022508.815344-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VLAN-untagged traffic
Robert Hodaszi reports that locally terminated traffic towards
VLAN-unaware bridge ports is broken with ocelot-8021q. He is describing
the same symptoms as for commit 1f9fc48fd302 ("net: dsa: sja1105: fix
reception from VLAN-unaware bridges").
For context, the set merged as "VLAN fixes for Ocelot driver":
https://lore.kernel.org/netdev/20240815000707.2006121-1-vladimir.oltean@nxp.com/
was developed in a slightly different form earlier this year, in January.
Initially, the switch was unconditionally configured to set OCELOT_ES0_TAG
when using ocelot-8021q, regardless of port operating mode.
This led to the situation where VLAN-unaware bridge ports would always
push their PVID - see ocelot_vlan_unaware_pvid() - a negligible value
anyway - into RX packets. To strip this in software, we would have needed
DSA to know what private VID the switch chose for VLAN-unaware bridge
ports, and pushed into the packets. This was implemented downstream, and
a remnant of it remains in the form of a comment mentioning
ds->ops->get_private_vid(), as something which would maybe need to be
considered in the future.
However, for upstream, it was deemed inappropriate, because it would
mean introducing yet another behavior for stripping VLAN tags from
VLAN-unaware bridge ports, when one already existed (ds->untag_bridge_pvid).
The latter has been marked as obsolete along with an explanation why it
is logically broken, but still, it would have been confusing.
So, for upstream, felix_update_tag_8021q_rx_rule() was developed, which
essentially changed the state of affairs from "Felix with ocelot-8021q
delivers all packets as VLAN-tagged towards the CPU" into "Felix with
ocelot-8021q delivers all packets from VLAN-aware bridge ports towards
the CPU". This was done on the premise that in VLAN-unaware mode,
there's nothing useful in the VLAN tags, and we can avoid introducing
ds->ops->get_private_vid() in the DSA receive path if we configure the
switch to not push those VLAN tags into packets in the first place.
Unfortunately, and this is when the trainwreck started, the selftests
developed initially and posted with the series were not re-ran.
dsa_software_vlan_untag() was initially written given the assumption
that users of this feature would send _all_ traffic as VLAN-tagged.
It was only partially adapted to the new scheme, by removing
ds->ops->get_private_vid(), which also used to be necessary in
standalone ports mode.
Where the trainwreck became even worse is that I had a second opportunity
to think about this, when the dsa_software_vlan_untag() logic change
initially broke sja1105, in commit 1f9fc48fd302 ("net: dsa: sja1105: fix
reception from VLAN-unaware bridges"). I did not connect the dots that
it also breaks ocelot-8021q, for pretty much the same reason that not
all received packets will be VLAN-tagged.
To be compatible with the optimized Felix control path which runs
felix_update_tag_8021q_rx_rule() to only push VLAN tags when useful (in
VLAN-aware mode), we need to restore the old dsa_software_vlan_untag()
logic. The blamed commit introduced the assumption that
dsa_software_vlan_untag() will see only VLAN-tagged packets, assumption
which is false. What corrupts RX traffic is the fact that we call
skb_vlan_untag() on packets which are not VLAN-tagged in the first
place.
Fixes: 93e4649efa96 ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Reported-by: Robert Hodaszi <robert.hodaszi@digi.com>
Closes: https://lore.kernel.org/netdev/20241215163334.615427-1-robert.hodaszi@digi.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241216135059.1258266-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
idpf: trigger SW interrupt when exiting wb_on_itr mode
Joshua Hay says:
This patch series introduces SW triggered interrupt support for idpf,
then uses said interrupt to fix a race condition between completion
writebacks and re-enabling interrupts.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: trigger SW interrupt when exiting wb_on_itr mode
idpf: add support for SW triggered interrupts
====================
Link: https://patch.msgid.link/20241217225715.4005644-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the way tcpdump is executed by:
- Using the right variable for the namespace. Currently the use of the
empty "ns" makes the command fail.
- Waiting until it starts to capture to ensure the interesting traffic
is caught on slow systems.
- Using line-buffered output to ensure logs are available when the test
is paused with "-p". Otherwise the last chunk of data might only be
written when tcpdump is killed.
Fixes: 74cc26f416b9 ("selftests: openvswitch: add interface support")
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://patch.msgid.link/20241217211652.483016-1-amorenoz@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2024-12-18
There are 2 patches by Matthias Schiffer for the m_can_pci driver that
handles the m_can cores found on the Intel Elkhart Lake processor.
They fix the initialization and the interrupt handling under high CAN
bus load.
* tag 'linux-can-fixes-for-6.13-20241218' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: fix missed interrupts with m_can_pci
can: m_can: set init flag earlier in probe
====================
Link: https://patch.msgid.link/20241218121722.2311963-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for Quectel RG255C which is based on Qualcomm SDX35 chip.
The composition is DM / NMEA / AT / QMI.
T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0316 Rev= 5.15
S: Manufacturer=Quectel
S: Product=RG255C-CN
S: SerialNumber=c68192c1
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Martin Hou <martin.hou@foxmail.com>
Link: https://patch.msgid.link/tencent_17DDD787B48E8A5AB8379ED69E23A0CD9309@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gcc runs into undefined behavior at the end of the three led_polarity_set()
callback functions if it were called with a zero 'modes' argument and it
just ends the function there without returning from it.
This gets flagged by 'objtool' as a function that continues on
to the next one:
drivers/net/phy/aquantia/aquantia_leds.o: warning: objtool: aqr_phy_led_polarity_set+0xf: can't find jump dest instruction at .text+0x5d9
drivers/net/phy/intel-xway.o: warning: objtool: xway_gphy_led_polarity_set() falls through to next function xway_gphy_config_init()
drivers/net/phy/mxl-gpy.o: warning: objtool: gpy_led_polarity_set() falls through to next function gpy_led_hw_control_get()
There is no point to micro-optimize the behavior here to save a single-digit
number of bytes in the kernel, so just change this to a "return -EINVAL"
as we do when any unexpected bits are set.
Fixes: 1758af47b98c ("net: phy: intel-xway: add support for PHY LEDs")
Fixes: 9d55e68b19f2 ("net: phy: aquantia: correctly describe LED polarity override")
Fixes: eb89c79c1b8f ("net: phy: mxl-gpy: correctly describe LED polarity")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241217081056.238792-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With CONFIG_PROVE_LOCKING, when creating a set of type bitmap:ip, adding
it to a set of type list:set and populating it from iptables SET target
triggers a kernel warning:
| WARNING: possible recursive locking detected
| 6.12.0-rc7-01692-g5e9a28f41134-dirty #594 Not tainted
| --------------------------------------------
| ping/4018 is trying to acquire lock:
| ffff8881094a6848 (&set->lock){+.-.}-{2:2}, at: ip_set_add+0x28c/0x360 [ip_set]
|
| but task is already holding lock:
| ffff88811034c048 (&set->lock){+.-.}-{2:2}, at: ip_set_add+0x28c/0x360 [ip_set]
This is a false alarm: ipset does not allow nested list:set type, so the
loop in list_set_kadd() can never encounter the outer set itself. No
other set type supports embedded sets, so this is the only case to
consider.
To avoid the false report, create a distinct lock class for list:set
type ipset locks.
Fixes: f830837f0eed ("netfilter: ipset: list:set set type support")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The 'max_avail' value is calculated from the system memory
size using order_base_2().
order_base_2(x) is defined as '(x) ? fn(x) : 0'.
The compiler generates two copies of the code that follows
and then expands clamp(max, min, PAGE_SHIFT - 12) (11 on 32bit).
This triggers a compile-time assert since min is 5.
In reality a system would have to have less than 512MB memory
for the bounds passed to clamp to be reversed.
Swap the order of the arguments to clamp() to avoid the warning.
Replace the clamp_val() on the line below with clamp().
clamp_val() is just 'an accident waiting to happen' and not needed here.
Detected by compile time checks added to clamp(), specifically:
minmax.h: use BUILD_BUG_ON_MSG() for the lo < hi test in clamp()
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Closes: https://lore.kernel.org/all/CA+G9fYsT34UkGFKxus63H6UVpYi5GRZkezT9MRLfAbM3f6ke0g@mail.gmail.com/
Fixes: 4f325e26277b ("ipvs: dynamically limit the connection hash table")
Tested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- tree-checker catches invalid number of inline extent references
- zoned mode fixes:
- enhance zone append IO command so it also detects emulated writes
- handle bio splitting at sectorsize boundary
- when deleting a snapshot, fix a condition for visiting nodes in reloc
trees
* tag 'for-6.13-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: tree-checker: reject inline extent items with 0 ref count
btrfs: split bios to the fs sector size boundary
btrfs: use bio_is_zone_append() in the completion handler
btrfs: fix improper generation check in snapshot delete
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Ira Weiny:
- prevent probe failure when non-critical RAS unmasking fails
- fix CXL 1.1 link status sysfs attribute
- fix 4 way (and greater) switch interleave region creation
* tag 'cxl-fixes-6.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/region: Fix region creation for greater than x2 switches
cxl/pci: Check dport->regs.rcd_pcie_cap availability before accessing
cxl/pci: Fix potential bogus return value upon successful probing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fix from Paul Moore:
"One small SELinux patch to get rid improve our handling of unknown
extended permissions by safely ignoring them.
Not only does this make it easier to support newer SELinux policy
on older kernels in the future, it removes to BUG() calls from the
SELinux code."
* tag 'selinux-pr-20241217' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: ignore unknown extended permissions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
"Replace trace_check_vprintf() with test_event_printk() and
ignore_event()
The function test_event_printk() checks on boot up if the trace event
printf() formats dereference any pointers, and if they do, it then
looks at the arguments to make sure that the pointers they dereference
will exist in the event on the ring buffer. If they do not, it issues
a WARN_ON() as it is a likely bug.
But this isn't the case for the strings that can be dereferenced with
"%s", as some trace events (notably RCU and some IPI events) save a
pointer to a static string in the ring buffer. As the string it points
to lives as long as the kernel is running, it is not a bug to
reference it, as it is guaranteed to be there when the event is read.
But it is also possible (and a common bug) to point to some allocated
string that could be freed before the trace event is read and the
dereference is to bad memory. This case requires a run time check.
The previous way to handle this was with trace_check_vprintf() that
would process the printf format piece by piece and send what it didn't
care about to vsnprintf() to handle arguments that were not strings.
This kept it from having to reimplement vsnprintf(). But it relied on
va_list implementation and for architectures that copied the va_list
and did not pass it by reference, it wasn't even possible to do this
check and it would be skipped. As 64bit x86 passed va_list by
reference, most events were tested and this kept out bugs where
strings would have been dereferenced after being freed.
Instead of relying on the implementation of va_list, extend the boot
up test_event_printk() function to validate all the "%s" strings that
can be validated at boot, and for the few events that point to strings
outside the ring buffer, flag both the event and the field that is
dereferenced as "needs_test". Then before the event is printed, a call
to ignore_event() is made, and if the event has the flag set, it
iterates all its fields and for every field that is to be tested, it
will read the pointer directly from the event in the ring buffer and
make sure that it is valid. If the pointer is not valid, it will print
a WARN_ON(), print out to the trace that the event has unsafe memory
and ignore the print format.
With this new update, the trace_check_vprintf() can be safely removed
and now all events can be verified regardless of architecture"
* tag 'trace-v6.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Check "%s" dereference via the field and not the TP_printk format
tracing: Add "%s" check in test_event_printk()
tracing: Add missing helper functions in event pointer dereference check
tracing: Fix test_event_printk() to process entire print argument
|
|
A recent refactoring was identified by smatch to cause another potential NULL
dereference:
drivers/net/wireless/st/cw1200/cw1200_spi.c:440 cw1200_spi_disconnect() error: we previously assumed 'self' could be null (see line 433)
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202411271742.Xa7CNVh1-lkp@intel.com/
Fixes: 2719a9e7156c ("wifi: cw1200: Convert to GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217-cw1200-fix-v1-1-911e6b5823ec@linaro.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Various fixes to Hyper-V tools in the kernel tree (Dexuan Cui, Olaf
Hering, Vitaly Kuznetsov)
- Fix a bug in the Hyper-V TSC page based sched_clock() (Naman Jain)
- Two bug fixes in the Hyper-V utility functions (Michael Kelley)
- Convert open-coded timeouts to secs_to_jiffies() in Hyper-V drivers
(Easwar Hariharan)
* tag 'hyperv-fixes-signed-20241217' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
tools/hv: reduce resource usage in hv_kvp_daemon
tools/hv: add a .gitignore file
tools/hv: reduce resouce usage in hv_get_dns_info helper
hv/hv_kvp_daemon: Pass NIC name to hv_get_dns_info as well
Drivers: hv: util: Avoid accessing a ringbuffer not initialized yet
Drivers: hv: util: Don't force error code to ENODEV in util_probe()
tools/hv: terminate fcopy daemon if read from uio fails
drivers: hv: Convert open-coded timeouts to secs_to_jiffies()
tools: hv: change permissions of NetworkManager configuration file
x86/hyperv: Fix hv tsc page based sched_clock for hibernation
tools: hv: Fix a complier warning in the fcopy uio daemon
|
|
In 32-bit x86 builds CONFIG_STATIC_CALL_INLINE isn't set, leading to
static_call_initialized not being available.
Define it as "0" in that case.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 0ef8047b737d ("x86/static-call: provide a way to do very early static-call updates")
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Both struct cfg80211_wowlan_nd_match and struct cfg80211_wowlan_nd_info
pre-allocate space for channels and matches, but then may end up using
fewer that the full allocation. Shrink the associated counter
(n_channels and n_matches) after counting the results. This avoids
compile-time (and run-time) warnings from __counted_by. (The counter
member needs to be updated _before_ accessing the array index.)
Seen with coming GCC 15:
drivers/net/wireless/intel/iwlwifi/mvm/d3.c: In function 'iwl_mvm_query_set_freqs':
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2877:66: warning: operation on 'match->n_channels' may be undefined [-Wsequence-point]
2877 | match->channels[match->n_channels++] =
| ~~~~~~~~~~~~~~~~~^~
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2885:66: warning: operation on 'match->n_channels' may be undefined [-Wsequence-point]
2885 | match->channels[match->n_channels++] =
| ~~~~~~~~~~~~~~~~~^~
drivers/net/wireless/intel/iwlwifi/mvm/d3.c: In function 'iwl_mvm_query_netdetect_reasons':
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2982:58: warning: operation on 'net_detect->n_matches' may be undefined [-Wsequence-point]
2982 | net_detect->matches[net_detect->n_matches++] = match;
| ~~~~~~~~~~~~~~~~~~~~~^~
Cc: stable@vger.kernel.org
Fixes: aa4ec06c455d ("wifi: cfg80211: use __counted_by where appropriate")
Signed-off-by: Kees Cook <kees@kernel.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/20240619211233.work.355-kees@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the timer supports complementary output, the CCxNE bit must be set
additionally to the CCxE bit. So to not overwrite the latter use |=
instead of = to set the former.
Fixes: deaba9cff809 ("pwm: stm32: Implementation of the waveform callbacks")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20241217150021.2030213-1-fabrice.gasnier@foss.st.com
[ukleinek: Slightly improve commit log]
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
|
