| Age | Commit message (Collapse) | Author |
|---|
|
u8 forced_speed_duplex from value from igc_mac_info struct is not used.
This patch comes to tidy up the driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
MSI-X PBA Clear register is not used. This patch comes to tidy up the
driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add support for Qbv schedules where one queue stays open
in consecutive entries. Currently that's not supported.
Example schedule:
|tc qdisc replace dev ${INTERFACE} handle 100 parent root taprio num_tc 3 \
| map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
| queues 1@0 1@1 2@2 \
| base-time ${BASETIME} \
| sched-entry S 0x01 300000 \ # Stream High/Low
| sched-entry S 0x06 500000 \ # Management and Best Effort
| sched-entry S 0x04 200000 \ # Best Effort
| flags 0x02
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use netif_napi_add_tx() for NAPI in Tx direction instead of the regular
netif_napi_add() function.
Signed-off-by: Sieng-Piaw Liew <liew.s.piaw@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the of_match_ptr() pointer when dereferencing the
ksz_dt_ids which produce the unused variable warning.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
tls: rx: avoid skb_cow_data()
TLS calls skb_cow_data() on the skb it received from strparser
whenever it needs to hold onto the skb with the decrypted data.
(The alternative being decrypting directly to a user space buffer
in whic case the input skb doesn't get modified or used after.)
TLS needs the decrypted skb:
- almost always with TLS 1.3 (unless the new NoPad is enabled);
- when user space buffer is too small to fit the record;
- when BPF sockmap is enabled.
Most of the time the skb we get out of strparser is a clone of
a 64kB data unit coalsced by GRO. To make things worse skb_cow_data()
tries to output a linear skb and allocates it with GFP_ATOMIC.
This occasionally fails even under moderate memory pressure.
This patch set rejigs the TLS Rx so that we don't expect decryption
in place. The decryption handlers return an skb which may or may not
be the skb from strparser. For TLS 1.3 this results in a 20-30%
performance improvement without NoPad enabled.
v2: rebase after 3d8c51b25a23 ("net/tls: Check for errors in tls_device_init")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently CoW Rx skbs whenever we can't decrypt to a user
space buffer. The skbs can be enormous (64kB) and CoW does
a linear alloc which has a strong chance of failing under
memory pressure. Or even without, skb_cow_data() assumes
GFP_ATOMIC.
Allocate a new frag'd skb and decrypt into it. We finally
take advantage of the decrypted skb getting returned via
darg.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "zero-copy" path in SW TLS will engage either for no skbs or
for all but last. If the recvmsg parameters are right and the
socket can do ZC we'll ZC until the iterator can't fit a full
record at which point we'll decrypt one more record and copy
over the necessary bits to fill up the request.
The only reason we hold onto the ZC skbs which went thru the async
path until the end of recvmsg() is to count bytes. We need an accurate
count of zc'ed bytes so that we can calculate how much of the non-zc'd
data to copy. To allow freeing input skbs on the ZC path count only
how much of the list we'll need to consume.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Async crypto currently benefits from the fact that we decrypt
in place. When we allow input and output to be different skbs
we will have to hang onto the input while we move to the next
record. Clone the inputs and keep them on a list.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Async crypto TLS Rx currently waits for crypto to be done
in order to strip the TLS header and tailer. Simplify
the code by moving the pointers immediately, since only
TLS 1.2 is supported here there is no message padding.
This simplifies the decryption into a new skb in the next
patch as we don't have to worry about input vs output
skb in the decrypt_done() handler any more.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using ctx->recv_pkt after decryption read the skb
from darg.skb. This moves the decision of what the "output skb"
is to the decrypt handlers. For now after decrypt handler returns
successfully ctx->recv_pkt is simply moved to darg.skb, but it
will change soon.
Note that tls_decrypt_sg() cannot clear the ctx->recv_pkt
because it gets called to re-encrypt (i.e. by the device offload).
So we need an awkward temporary if() in tls_rx_one_record().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Callers always pass ctx->recv_pkt into decrypt_skb_update(),
and it propagates it to its callees. This may give someone
the false impression that those functions can accept any valid
skb containing a TLS record. That's not the case, the record
sequence number is read from the context, and they can only
take the next record coming out of the strp.
Let the functions get the skb from the context instead of
passing it in. This will also make it cleaner to return
a different skb than ctx->recv_pkt as the decrypted one
later on.
Since we're touching the definition of decrypt_skb_update()
use this as an opportunity to rename it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I already forgot to transform darg from input to output
semantics once on the NIC inline crypto fastpath. To
avoid this happening again create a device equivalent
of decrypt_internal(). A function responsible for decryption
and transforming darg.
While at it rename decrypt_internal() to a hopefully slightly
more meaningful name.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We no longer allow a decrypted skb to remain linked to ctx->recv_pkt.
Anything on the list is decrypted, anything on ctx->recv_pkt needs
to be decrypted.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Detach the skb from ctx->recv_pkt after decryption is done,
even if we can't consume it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I thought that having the skb either always on the ctx->rx_list
or ctx->recv_pkt will simplify the handling, as we would not
have to remember to flip it from one to the other on exit paths.
This became a little harder to justify with the fix for BPF
sockmaps. Subsequent changes will make the situation even worse.
Queue the skbs only when really needed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
recvmsg() in TLS gets data from the skb list (rx_list) or fresh
skbs we read from TCP via strparser. The former holds skbs which were
already decrypted for peek or decrypted and partially consumed.
tls_wait_data() only notices appearance of fresh skbs coming out
of TCP (or psock). It is possible, if there is a concurrent call
to peek() and recv() that the peek() will move the data from input
to rx_list without recv() noticing. recv() will then read data out
of order or never wake up.
This is not a practical use case/concern, but it makes the self
tests less reliable. This patch solves the problem by allowing
only one reader in.
Because having multiple processes calling read()/peek() is not
normal avoid adding a lock and try to fast-path the single reader
case.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wen Gu says:
====================
net/smc: Introduce virtually contiguous buffers for SMC-R
On long-running enterprise production servers, high-order contiguous
memory pages are usually very rare and in most cases we can only get
fragmented pages.
When replacing TCP with SMC-R in such production scenarios, attempting
to allocate high-order physically contiguous sndbufs and RMBs may result
in frequent memory compaction, which will cause unexpected hung issue
and further stability risks.
So this patch set is aimed to allow SMC-R link group to use virtually
contiguous sndbufs and RMBs to avoid potential issues mentioned above.
Whether to use physically or virtually contiguous buffers can be set
by sysctl smcr_buf_type.
Note that using virtually contiguous buffers will bring an acceptable
performance regression, which can be mainly divided into two parts:
1) regression in data path, which is brought by additional address
translation of sndbuf by RNIC in Tx. But in general, translating
address through MTT is fast. According to qperf test, this part
regression is basically less than 10% in latency and bandwidth.
(see patch 5/6 for details)
2) regression in buffer initialization and destruction path, which is
brought by additional MR operations of sndbufs. But thanks to link
group buffer reuse mechanism, the impact of this kind of regression
decreases as times of buffer reuse increases.
Patch set overview:
- Patch 1/6 and 2/6 mainly about simplifying and optimizing DMA sync
operation, which will reduce overhead on the data path, especially
when using virtually contiguous buffers;
- Patch 3/6 and 4/6 introduce a sysctl smcr_buf_type to set the type
of buffers in new created link group;
- Patch 5/6 allows SMC-R to use virtually contiguous sndbufs and RMBs,
including buffer creation, destruction, MR operation and access;
- patch 6/6 extends netlink attribute for buffer type of SMC-R link group;
v1->v2:
- Patch 5/6 fixes build issue on 32bit;
- Patch 3/6 adds description of new sysctl in smc-sysctl.rst;
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend SMC-R link group netlink attribute SMC_GEN_LGR_SMCR.
Introduce SMC_NLA_LGR_R_BUF_TYPE to show the buffer type of
SMC-R link group.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On long-running enterprise production servers, high-order contiguous
memory pages are usually very rare and in most cases we can only get
fragmented pages.
When replacing TCP with SMC-R in such production scenarios, attempting
to allocate high-order physically contiguous sndbufs and RMBs may result
in frequent memory compaction, which will cause unexpected hung issue
and further stability risks.
So this patch is aimed to allow SMC-R link group to use virtually
contiguous sndbufs and RMBs to avoid potential issues mentioned above.
Whether to use physically or virtually contiguous buffers can be set
by sysctl smcr_buf_type.
Note that using virtually contiguous buffers will bring an acceptable
performance regression, which can be mainly divided into two parts:
1) regression in data path, which is brought by additional address
translation of sndbuf by RNIC in Tx. But in general, translating
address through MTT is fast.
Taking 256KB sndbuf and RMB as an example, the comparisons in qperf
latency and bandwidth test with physically and virtually contiguous
buffers are as follows:
- client:
smc_run taskset -c <cpu> qperf <server> -oo msg_size:1:64K:*2\
-t 5 -vu tcp_{bw|lat}
- server:
smc_run taskset -c <cpu> qperf
[latency]
msgsize tcp smcr smcr-use-virt-buf
1 11.17 us 7.56 us 7.51 us (-0.67%)
2 10.65 us 7.74 us 7.56 us (-2.31%)
4 11.11 us 7.52 us 7.59 us ( 0.84%)
8 10.83 us 7.55 us 7.51 us (-0.48%)
16 11.21 us 7.46 us 7.51 us ( 0.71%)
32 10.65 us 7.53 us 7.58 us ( 0.61%)
64 10.95 us 7.74 us 7.80 us ( 0.76%)
128 11.14 us 7.83 us 7.87 us ( 0.47%)
256 10.97 us 7.94 us 7.92 us (-0.28%)
512 11.23 us 7.94 us 8.20 us ( 3.25%)
1024 11.60 us 8.12 us 8.20 us ( 0.96%)
2048 14.04 us 8.30 us 8.51 us ( 2.49%)
4096 16.88 us 9.13 us 9.07 us (-0.64%)
8192 22.50 us 10.56 us 11.22 us ( 6.26%)
16384 28.99 us 12.88 us 13.83 us ( 7.37%)
32768 40.13 us 16.76 us 16.95 us ( 1.16%)
65536 68.70 us 24.68 us 24.85 us ( 0.68%)
[bandwidth]
msgsize tcp smcr smcr-use-virt-buf
1 1.65 MB/s 1.59 MB/s 1.53 MB/s (-3.88%)
2 3.32 MB/s 3.17 MB/s 3.08 MB/s (-2.67%)
4 6.66 MB/s 6.33 MB/s 6.09 MB/s (-3.85%)
8 13.67 MB/s 13.45 MB/s 11.97 MB/s (-10.99%)
16 25.36 MB/s 27.15 MB/s 24.16 MB/s (-11.01%)
32 48.22 MB/s 54.24 MB/s 49.41 MB/s (-8.89%)
64 106.79 MB/s 107.32 MB/s 99.05 MB/s (-7.71%)
128 210.21 MB/s 202.46 MB/s 201.02 MB/s (-0.71%)
256 400.81 MB/s 416.81 MB/s 393.52 MB/s (-5.59%)
512 746.49 MB/s 834.12 MB/s 809.99 MB/s (-2.89%)
1024 1292.33 MB/s 1641.96 MB/s 1571.82 MB/s (-4.27%)
2048 2007.64 MB/s 2760.44 MB/s 2717.68 MB/s (-1.55%)
4096 2665.17 MB/s 4157.44 MB/s 4070.76 MB/s (-2.09%)
8192 3159.72 MB/s 4361.57 MB/s 4270.65 MB/s (-2.08%)
16384 4186.70 MB/s 4574.13 MB/s 4501.17 MB/s (-1.60%)
32768 4093.21 MB/s 4487.42 MB/s 4322.43 MB/s (-3.68%)
65536 4057.14 MB/s 4735.61 MB/s 4555.17 MB/s (-3.81%)
2) regression in buffer initialization and destruction path, which is
brought by additional MR operations of sndbufs. But thanks to link
group buffer reuse mechanism, the impact of this kind of regression
decreases as times of buffer reuse increases.
Taking 256KB sndbuf and RMB as an example, latency of some key SMC-R
buffer-related function obtained by bpftrace are as follows:
Function Phys-bufs Virt-bufs
smcr_new_buf_create() 67154 ns 79164 ns
smc_ib_buf_map_sg() 525 ns 928 ns
smc_ib_get_memory_region() 162294 ns 161191 ns
smc_wr_reg_send() 9957 ns 9635 ns
smc_ib_put_memory_region() 203548 ns 198374 ns
smc_ib_buf_unmap_sg() 508 ns 1158 ns
------------
Test environment notes:
1. Above tests run on 2 VMs within the same Host.
2. The NIC is ConnectX-4Lx, using SRIOV and passing through 2 VFs to
the each VM respectively.
3. VMs' vCPUs are binded to different physical CPUs, and the binded
physical CPUs are isolated by `isolcpus=xxx` cmdline.
4. NICs' queue number are set to 1.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces a new SMC-R specific element buf_type
in struct smc_link_group, for recording the value of sysctl
smcr_buf_type when link group is created.
New created link group will create and reuse buffers of the
type specified by buf_type.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces the sysctl smcr_buf_type for setting
the type of SMC-R sndbufs and RMBs.
Valid values includes:
- SMCR_PHYS_CONT_BUFS, which means use physically contiguous
buffers for better performance and is the default value.
- SMCR_VIRT_CONT_BUFS, which means use virtually contiguous
buffers in case of physically contiguous memory is scarce.
- SMCR_MIXED_BUFS, which means first try to use physically
contiguous buffers. If not available, then use virtually
contiguous buffers.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some CPU, such as Xeon, can guarantee DMA cache coherency.
So it is no need to use dma sync APIs to flush cache on such CPUs.
In order to avoid calling dma sync APIs on the IO path, use the
dma_need_sync to check whether smc_buf_desc needs dma sync when
creating smc_buf_desc.
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smc_ib_sync_sg_for_cpu/device are the ops used for dma memory cache
consistency. Smc sndbufs are dma buffers, where CPU writes data to
it and PCIE device reads data from it. So for sndbufs,
smc_ib_sync_sg_for_device is needed and smc_ib_sync_sg_for_cpu is
redundant as PCIE device will not write the buffers. Smc rmbs
are dma buffers, where PCIE device write data to it and CPU read
data from it. So for rmbs, smc_ib_sync_sg_for_cpu is needed and
smc_ib_sync_sg_for_device is redundant as CPU will not write the buffers.
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'net-ipv4-ipv6-new-option-to-accept-garp-untracked-na-only-if-in-network'
Jaehee Park says:
====================
net: ipv4/ipv6: new option to accept garp/untracked na only if in-network
The first patch adds an option to learn a neighbor from garp only if
the source ip is in the same subnet as an address configured on the
interface that received the garp message. The option has been added
to arp_accept in ipv4.
The same feature has been added to ndisc (patch 2). For ipv6, the
subnet filtering knob is an extension of the accept_untracked_na
option introduced in these patches:
https://lore.kernel.org/all/642672cb-8b11-c78f-8975-f287ece9e89e@gmail.com/t/
https://lore.kernel.org/netdev/20220530101414.65439-1-aajith@arista.com/T/
The third patch contains selftests for testing the different options
for accepting arp and neighbor advertisements.
====================
Link: https://lore.kernel.org/r/cover.1657755188.git.jhpark1013@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
accept_untracked_na
ipv4 arp_accept has a new option '2' to create new neighbor entries
only if the src ip is in the same subnet as an address configured on
the interface that received the garp message. This selftest tests all
options in arp_accept.
ipv6 has a sysctl endpoint, accept_untracked_na, that defines the
behavior for accepting untracked neighbor advertisements. A new option
similar to that of arp_accept for learning only from the same subnet is
added to accept_untracked_na. This selftest tests this new feature.
Signed-off-by: Jaehee Park <jhpark1013@gmail.com>
Suggested-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds a third knob, '2', which extends the
accept_untracked_na option to learn a neighbor only if the src ip is
in the same subnet as an address configured on the interface that
received the neighbor advertisement. This is similar to the arp_accept
configuration for ipv4.
Signed-off-by: Jaehee Park <jhpark1013@gmail.com>
Suggested-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In many deployments, we want the option to not learn a neighbor from
garp if the src ip is not in the same subnet as an address configured
on the interface that received the garp message. net.ipv4.arp_accept
sysctl is currently used to control creation of a neigh from a
received garp packet. This patch adds a new option '2' to
net.ipv4.arp_accept which extends option '1' by including the subnet
check.
Signed-off-by: Jaehee Park <jhpark1013@gmail.com>
Suggested-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When number of LMACs active on a CGX/RPM are 3, then
current NIX link credit config based on per lmac fifo
length which inturn is calculated as
'lmac_fifo_len = total_fifo_len / 3', is incorrect. In HW
one of the LMAC gets half of the FIFO and rest gets 1/4th.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha Sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes smatch static tool warning reported by smatch tool.
rvu_npc_hash.c:1232 rvu_npc_exact_del_table_entry_by_id() error:
uninitialized symbol 'drop_mcam_idx'.
rvu_npc_hash.c:1312 rvu_npc_exact_add_table_entry() error:
uninitialized symbol 'drop_mcam_idx'.
rvu_npc_hash.c:1391 rvu_npc_exact_update_table_entry() error:
uninitialized symbol 'hash_index'.
rvu_npc_hash.c:1428 rvu_npc_exact_promisc_disable() error:
uninitialized symbol 'drop_mcam_idx'.
rvu_npc_hash.c:1473 rvu_npc_exact_promisc_enable() error:
uninitialized symbol 'drop_mcam_idx'.
otx2_dmac_flt.c:191 otx2_dmacflt_update() error: 'rsp'
dereferencing possible ERR_PTR()
otx2_dmac_flt.c:60 otx2_dmacflt_add_pfmac() error: 'rsp'
dereferencing possible ERR_PTR()
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move qca8k driver to qca dir in preparation for code split and
introduction of ipq4019 switch based on qca8k.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
delay_timer has been unused since commit c3498d34dd36 ("cbq: remove
TCA_CBQ_OVL_STRATEGY support"). Delete it.
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2022-07-13
1) Support 802.1ad for bridge offloads
Vlad Buslov Says:
=================
Current mlx5 bridge VLAN offload implementation only supports 802.1Q VLAN
Ethernet protocol. That protocol type is assumed by default and
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL notification is ignored.
In order to support dynamically setting VLAN protocol handle
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL notification by flushing FDB and
re-creating VLAN modify header actions with a new protocol. Implement support
for 802.1ad protocol by saving the current VLAN protocol to per-bridge variable
and re-create the necessary flow groups according to its current value (either
use cvlan or svlan flow fields).
==================
2) debugfs to count ongoing FW commands
3) debugfs to query eswitch vport firmware diagnostic counters
4) Add missing meter configuration in flow action
5) Some misc cleanup
* tag 'mlx5-updates-2022-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Remove the duplicating check for striding RQ when enabling LRO
net/mlx5e: Move the LRO-XSK check to mlx5e_fix_features
net/mlx5e: Extend flower police validation
net/mlx5e: configure meter in flow action
net/mlx5e: Removed useless code in function
net/mlx5: Bridge, implement QinQ support
net/mlx5: Bridge, implement infrastructure for VLAN protocol change
net/mlx5: Bridge, extract VLAN push/pop actions creation
net/mlx5: Bridge, rename filter fg to vlan_filter
net/mlx5: Bridge, refactor groups sizes and indices
net/mlx5: debugfs, Add num of in-use FW command interface slots
net/mlx5: Expose vnic diagnostic counters for eswitch managed vports
net/mlx5: Use software VHCA id when it's supported
net/mlx5: Introduce ifc bits for using software vhca id
net/mlx5: Use the bitmap API to allocate bitmaps
====================
Link: https://lore.kernel.org/r/20220713225859.401241-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jiri Pirko says:
====================
net: devlink: couple of trivial fixes
Just a couple of trivial fixes I found on the way.
====================
Link: https://lore.kernel.org/r/20220713141853.2992014-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Return directly without intermediate value store at the end of
devlink_port_new_notify() function.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the typo in a name of devlink_port_new_notifiy() function.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The return value is not used, so change the return value type to void.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
include/net/sock.h
310731e2f161 ("net: Fix data-races around sysctl_mem.")
e70f3c701276 ("Revert "net: set SK_MEM_QUANTUM to 4096"")
https://lore.kernel.org/all/20220711120211.7c8b7cba@canb.auug.org.au/
net/ipv4/fib_semantics.c
747c14307214 ("ip: fix dflt addr selection for connected nexthop")
d62607c3fe45 ("net: rename reference+tracking helpers")
net/tls/tls.h
include/net/tls.h
3d8c51b25a23 ("net/tls: Check for errors in tls_device_init")
587903142308 ("tls: create an internal header")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clang warns:
arch/x86/kernel/cpu/bugs.c:58:21: error: section attribute is specified on redeclared variable [-Werror,-Wsection]
DEFINE_PER_CPU(u64, x86_spec_ctrl_current);
^
arch/x86/include/asm/nospec-branch.h:283:12: note: previous declaration is here
extern u64 x86_spec_ctrl_current;
^
1 error generated.
The declaration should be using DECLARE_PER_CPU instead so all
attributes stay in sync.
Cc: stable@vger.kernel.org
Fixes: fc02735b14ff ("KVM: VMX: Prevent guest RSB poisoning attacks with eIBRS")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, bpf and wireless.
Still no major regressions, the release continues to be calm. An
uptick of fixes this time around due to trivial data race fixes and
patches flowing down from subtrees.
There has been a few driver fixes (particularly a few fixes for false
positives due to 66e4c8d95008 which went into -next in May!) that make
me worry the wide testing is not exactly fully through.
So "calm" but not "let's just cut the final ASAP" vibes over here.
Current release - regressions:
- wifi: rtw88: fix write to const table of channel parameters
Current release - new code bugs:
- mac80211: add gfp_t arg to ieeee80211_obss_color_collision_notify
- mlx5:
- TC, allow offload from uplink to other PF's VF
- Lag, decouple FDB selection and shared FDB
- Lag, correct get the port select mode str
- bnxt_en: fix and simplify XDP transmit path
- r8152: fix accessing unset transport header
Previous releases - regressions:
- conntrack: fix crash due to confirmed bit load reordering (after
atomic -> refcount conversion)
- stmmac: dwc-qos: disable split header for Tegra194
Previous releases - always broken:
- mlx5e: ring the TX doorbell on DMA errors
- bpf: make sure mac_header was set before using it
- mac80211: do not wake queues on a vif that is being stopped
- mac80211: fix queue selection for mesh/OCB interfaces
- ip: fix dflt addr selection for connected nexthop
- seg6: fix skb checksums for SRH encapsulation/insertion
- xdp: fix spurious packet loss in generic XDP TX path
- bunch of sysctl data race fixes
- nf_log: incorrect offset to network header
Misc:
- bpf: add flags arg to bpf_dynptr_read and bpf_dynptr_write APIs"
* tag 'net-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
nfp: flower: configure tunnel neighbour on cmsg rx
net/tls: Check for errors in tls_device_init
MAINTAINERS: Add an additional maintainer to the AMD XGBE driver
xen/netback: avoid entering xenvif_rx_next_skb() with an empty rx queue
selftests/net: test nexthop without gw
ip: fix dflt addr selection for connected nexthop
net: atlantic: remove aq_nic_deinit() when resume
net: atlantic: remove deep parameter on suspend/resume functions
sfc: fix kernel panic when creating VF
seg6: bpf: fix skb checksum in bpf_push_seg6_encap()
seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps behaviors
seg6: fix skb checksum evaluation in SRH encapsulation/insertion
sfc: fix use after free when disabling sriov
net: sunhme: output link status with a single print.
r8152: fix accessing unset transport header
net: stmmac: fix leaks in probe
net: ftgmac100: Hold reference returned by of_get_child_by_name()
nexthop: Fix data-races around nexthop_compat_mode.
ipv4: Fix data-races around sysctl_ip_dynaddr.
tcp: Fix a data-race around sysctl_tcp_ecn_fallback.
...
|
|
Pull cifs fixes from Steve French:
"Three smb3 client fixes:
- two multichannel fixes: fix a potential deadlock freeing a channel,
and fix a race condition on failed creation of a new channel
- mount failure fix: work around a server bug in some common older
Samba servers by avoiding padding at the end of the negotiate
protocol request"
* tag '5.19-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb3: workaround negprot bug in some Samba servers
cifs: remove unnecessary locking of chan_lock while freeing session
cifs: fix race condition with delayed threads
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Notable regression fixes:
- Enable SETATTR(time_create) to fix regression with Mac OS clients
- Fix a lockd crasher and broken NLM UNLCK behavior"
* tag 'nfsd-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
lockd: fix nlm_close_files
lockd: set fl_owner when unlocking files
NFSD: Decode NFSv4 birth time attribute
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity fixes from Mimi Zohar:
"Here are a number of fixes for recently found bugs.
Only 'ima: fix violation measurement list record' was introduced in
the current release. The rest address existing bugs"
* tag 'integrity-v5.19-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: Fix potential memory leak in ima_init_crypto()
ima: force signature verification when CONFIG_KEXEC_SIG is configured
ima: Fix a potential integer overflow in ima_appraise_measurement
ima: fix violation measurement list record
Revert "evm: Fix memleak in init_desc"
|
|
Pull ARM fixes from Russell King:
- quieten the spectre-bhb prints
- mark flattened device tree sections as shareable
- remove some obsolete CPU domain code and help text
- fix thumb unaligned access abort emulation
- fix amba_device_add() refcount underflow
- fix literal placement
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9208/1: entry: add .ltorg directive to keep literals in range
ARM: 9207/1: amba: fix refcount underflow if amba_device_add() fails
ARM: 9214/1: alignment: advance IT state after emulating Thumb instruction
ARM: 9213/1: Print message about disabled Spectre workarounds only once
ARM: 9212/1: domain: Modify Kconfig help text
ARM: 9211/1: domain: drop modify_domain()
ARM: 9210/1: Mark the FDT_FIXED sections as shareable
ARM: 9209/1: Spectre-BHB: avoid pr_info() every time a CPU comes out of idle
|
|
The UML function names to_virt() and to_phys() are exposed by UML
headers, and are very generic and may be defined by drivers. As it
turns out, commit 9409c9b6709e ("pmem: refactor pmem_clear_poison()")
did exactly that.
This results in build errors such as the following when trying to build
um:allmodconfig:
drivers/nvdimm/pmem.c: In function ‘pmem_dax_zero_page_range’:
./arch/um/include/asm/page.h:105:20: error: too few arguments to function ‘to_phys’
105 | #define __pa(virt) to_phys((void *) (unsigned long) (virt))
| ^~~~~~~
Use less generic function names for the um specific to_phys() and
to_virt() functions to fix the problem and to avoid similar problems in
the future.
Fixes: 9409c9b6709e ("pmem: refactor pmem_clear_poison()")
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the last one for 5.19. This became bigger than wished, but
all changes are pretty device-specific small fixes, which look less
worrisome.
The majority of changes are about various ASoC fixes, while the usual
HD-audio quirks are included as well"
* tag 'sound-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (28 commits)
ALSA: hda/realtek - Enable the headset-mic on a Xiaomi's laptop
ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc221
ALSA: hda/realtek: fix mute/micmute LEDs for HP machines
ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
ALSA: hda - Add fixup for Dell Latitidue E5430
ALSA: hda/conexant: Apply quirk for another HP ProDesk 600 G3 model
ALSA: hda/realtek: Fix headset mic for Acer SF313-51
ASoC: Intel: Skylake: Correct the handling of fmt_config flexible array
ASoC: Intel: Skylake: Correct the ssp rate discovery in skl_get_ssp_clks()
ASoC: rt5640: Fix the wrong state of JD1 and JD2
ASoC: Intel: sof_rt5682: fix out-of-bounds array access
ASoC: qdsp6: fix potential memory leak in q6apm_get_audioreach_graph()
ASoC: tas2764: Fix amp gain register offset & default
ASoC: tas2764: Correct playback volume range
ASoC: tas2764: Fix and extend FSYNC polarity handling
ASoC: tas2764: Add post reset delays
ASoC: dt-bindings: Fix description for msm8916
ASoC: doc: Capitalize RESET line name
ASoC: arizona: Update arizona_aif_cfg_changed to use RX_BCLK_RATE
ASoC: cs47l92: Fix event generation for OUT1 demux
...
|
|
nfp_tun_write_neigh() function will configure a tunnel neighbour when
calling nfp_tun_neigh_event_handler() or nfp_flower_cmsg_process_one_rx()
(with no tunnel neighbour type) from firmware.
When configuring IP on physical port as a tunnel endpoint, no operation
will be performed after receiving the cmsg mentioned above.
Therefore, add a progress to configure tunnel neighbour in this case.
v2: Correct format of fixes tag.
Fixes: f1df7956c11f ("nfp: flower: rework tunnel neighbour configuration")
Signed-off-by: Tianyu Yuan <tianyu.yuan@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220714081915.148378-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add missing error checks in tls_device_init.
Fixes: e8f69799810c ("net/tls: Add generic NIC offload infrastructure")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220714070754.1428-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add Shyam Sundar S K as an additional maintainer to support the AMD XGBE
network device driver.
Cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/db367f24089c2bbbcd1cec8e21af49922017a110.1657751501.git.thomas.lendacky@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xenvif_rx_next_skb() is expecting the rx queue not being empty, but
in case the loop in xenvif_rx_action() is doing multiple iterations,
the availability of another skb in the rx queue is not being checked.
This can lead to crashes:
[40072.537261] BUG: unable to handle kernel NULL pointer dereference at 0000000000000080
[40072.537407] IP: xenvif_rx_skb+0x23/0x590 [xen_netback]
[40072.537534] PGD 0 P4D 0
[40072.537644] Oops: 0000 [#1] SMP NOPTI
[40072.537749] CPU: 0 PID: 12505 Comm: v1-c40247-q2-gu Not tainted 4.12.14-122.121-default #1 SLE12-SP5
[40072.537867] Hardware name: HP ProLiant DL580 Gen9/ProLiant DL580 Gen9, BIOS U17 11/23/2021
[40072.537999] task: ffff880433b38100 task.stack: ffffc90043d40000
[40072.538112] RIP: e030:xenvif_rx_skb+0x23/0x590 [xen_netback]
[40072.538217] RSP: e02b:ffffc90043d43de0 EFLAGS: 00010246
[40072.538319] RAX: 0000000000000000 RBX: ffffc90043cd7cd0 RCX: 00000000000000f7
[40072.538430] RDX: 0000000000000000 RSI: 0000000000000006 RDI: ffffc90043d43df8
[40072.538531] RBP: 000000000000003f R08: 000077ff80000000 R09: 0000000000000008
[40072.538644] R10: 0000000000007ff0 R11: 00000000000008f6 R12: ffffc90043ce2708
[40072.538745] R13: 0000000000000000 R14: ffffc90043d43ed0 R15: ffff88043ea748c0
[40072.538861] FS: 0000000000000000(0000) GS:ffff880484600000(0000) knlGS:0000000000000000
[40072.538988] CS: e033 DS: 0000 ES: 0000 CR0: 0000000080050033
[40072.539088] CR2: 0000000000000080 CR3: 0000000407ac8000 CR4: 0000000000040660
[40072.539211] Call Trace:
[40072.539319] xenvif_rx_action+0x71/0x90 [xen_netback]
[40072.539429] xenvif_kthread_guest_rx+0x14a/0x29c [xen_netback]
Fix that by stopping the loop in case the rx queue becomes empty.
Cc: stable@vger.kernel.org
Fixes: 98f6d57ced73 ("xen-netback: process guest rx packets in batches")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20220713135322.19616-1-jgross@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
