| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
SCMI fixes for v5.15
A few fixes addressing:
- Kconfig dependency between VIRTIO and ARM_SCMI_PROTOCOL
- Link-time error with __exit annotation for virtio_scmi_exit
- Unnecessary nested irqsave/irqrestore spinlocks in virtio transport
- Missing SMP barriers to protect accesses to SCMI virtio device
* tag 'scmi-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Add proper barriers to scmi virtio device
firmware: arm_scmi: Simplify spinlocks in virtio transport
firmware: arm_scmi: Remove __exit annotation
firmware: arm_scmi: Fix virtio transport Kconfig dependency
Link: https://lore.kernel.org/r/20211007102822.27886-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.15
Few regression fixes for omaps for the v5.15-rc cycle. There is a fix
for boot time hangs that can happen on some am335x devices that started
when the pruss devicetree nodes were added. The other fixes are less
critical:
- Fix compiler warning for sysc_init_soc() that got recently introduced
- Fix external abort for am335x pruss as otherwise some am335x will hang
- Use CLKDM_NOAUTO quirk also for dra7 dcan1
- Fix older NAND device node regression for omap3-sdp
* tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3430-sdp: Fix NAND device node
bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
soc: ti: omap-prm: Fix external abort for am335x pruss
bus: ti-sysc: Add break in switch statement in sysc_init_soc()
Link: https://lore.kernel.org/r/pull-1633609552-789682@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.15, round 2:
- A couple of fixes from Haibo Chen to update SPI NOR TX bus width for
i.MX6 and i.MX8 boards. This becomes necessary because spi-nor driver
starts using the setting in DT.
- Mark buck2 always-on for i.MX8MM Kontron-n801x-som board to avoid the
core supply being turned off unexpectedly.
- Fix eSDHC2 device tree settings for LS1028A SoC.
- Disable GIC CPU interface before calling stby-poweroff sequence to fix
power-off failure on i.MX6.
- Fix M2_RST# GPIO pinmux on i.MX8M venice-gw7902 boards.
* tag 'imx-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
arm64: dts: ls1028a: fix eSDHC2 node
arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
arm64: dts: imx8: change the spi-nor tx
ARM: dts: imx: change the spi-nor tx
Link: https://lore.kernel.org/r/20211006125734.GA10197@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Only one single SCMI Virtio device is currently supported by this driver
and it is referenced using a static global variable which is initialized
once for all during probing and nullified at virtio device removal.
Add proper SMP barriers to protect accesses to such device reference to
ensure that the initialzation state of such device is correctly observed by
all PEs at any time.
Return -EBUSY, instead of -EINVAL, and a descriptive error message if more
than one SCMI Virtio device is ever found and probed.
Link: https://lore.kernel.org/r/20210916103336.7243-3-cristian.marussi@arm.com
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Remove unneeded nested irqsave/irqrestore spinlocks.
Add also a few descriptive comments to explain better the system behaviour
at shutdown time.
Link: https://lore.kernel.org/r/20210916103336.7243-2-cristian.marussi@arm.com
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Nand is on CS1 so reg properties first field should be 1 not 0.
Fixes: 44e4716499b8 ("ARM: dts: omap3: Fix NAND device nodes")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 94f6345712b3 ("bus: ti-sysc: Implement quirk handling for
CLKDM_NOAUTO") should have also added the quirk for dra7 dcan1 in
addition to dcan2 for errata i893 handling.
Let's also pass the quirk flag for legacy mode booting for if "ti,hwmods"
dts property is used with related dcan hwmod data. This should be only
needed if anybody needs to git bisect earlier stable trees though.
Fixes: 94f6345712b3 ("bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Merge in a fix for pruss reset issue caused by enabling pruss for am335x.
|
|
gcc warns that accessing a pointer based on a numeric constant may
be an offset into a NULL pointer, and would therefore has zero
accessible bytes:
arch/arm/common/sharpsl_param.c: In function ‘sharpsl_save_param’:
arch/arm/common/sharpsl_param.c:43:9: error: ‘memcpy’ reading 64 bytes from a region of size 0 [-Werror=stringop-overread]
43 | memcpy(&sharpsl_param, param_start(PARAM_BASE), sizeof(struct sharpsl_param_info));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In this particular case, the warning is bogus since this is the actual
pointer, not an offset on a NULL pointer. Add a local variable to shut
up the warning and hope it doesn't come back.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99578
Link: https://lore.kernel.org/r/20210927145332.2784005-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.15:
- Revert cc8870bf4c3a to fix the regression on i.MX6 that suspend
support becomes broken.
- Add `qca,clk-out-frequency` property to fix Ethernet support on
imx6qdl-pico board.
- Re-enable FB support in imx_v6_v7_defconfig. It gets lost due to
f611b1e7624c ("drm: Avoid circular dependencies for CONFIG_FB").
- Fix LP5562 LED support on imx6dl-yapp4 board.
- Add missing pinctrl-names for panel on M53Menlo board.
- Fix USB host power regulator polarity on M53Menlo board.
* tag 'imx-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: enable fb
ARM: dts: imx6qdl-pico: Fix Ethernet support
ARM: dts: imx: Fix USB host power regulator polarity on M53Menlo
ARM: dts: imx: Add missing pinctrl-names for panel on M53Menlo
Revert "ARM: imx6q: drop of_platform_default_populate() from init_machine"
ARM: dts: imx6dl-yapp4: Fix lp5562 LED driver probe
Link: https://lore.kernel.org/r/20210923063356.GK13480@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The framebuffer is gone on the D-Link DIR-685, restore it.
Fixes: f611b1e7624c ("drm: Avoid circular dependencies for CONFIG_FB")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210922200933.1825752-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This can cause a randconfig warning without the 'inline' flag
that every other platform uses:
In file included from arch/arm/boot/compressed/misc.c:29:
arch/arm/mach-dove/include/mach/uncompress.h:14:13: error: 'putc' defined but not used [-Werror=unused-function]
14 | static void putc(const char c)
| ^~~~
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210927095343.1015422-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 38225f2ef2f4 ("ARM/omap1: switch to use dma_direct_set_offset for
lbus DMA offsets") removed a lot of mach/memory.h, but left the USB
offset handling split into arch/arm/mach-omap1/usb.c and
drivers/usb/host/ohci-omap.c.
This can cause a randconfig build warning that now fails the build
with -Werror:
arch/arm/mach-omap1/usb.c:561:30: error: 'omap_1510_usb_ohci_nb' defined but not used [-Werror=unused-variable]
561 | static struct notifier_block omap_1510_usb_ohci_nb = {
| ^~~~~~~~~~~~~~~~~~~~~
Move it all into the platform file to get rid of the final
location that relies on mach/memory.h.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210927144118.2464881-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm driver fixes for v5.15
This restricts the QCOM_SCM driver to depend on ARCH_QCOM, to reduce
it's presence after becoming a loadable module.
It then fixes a regression in the mdt_loader, where firmware with the
hash segment marked as PT_LOAD would no longer be accepted, preventing
several MSM8974 and SDM660 devices from loading remoteproc firmware.
Lastly it corrects the drvdata associated with the socinfo device during
probe, to match that expected by the remove function.
* tag 'qcom-drivers-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
firmware: qcom_scm: QCOM_SCM should depend on ARCH_QCOM
soc: qcom: mdt_loader: Drop PT_LOAD check on hash segment
soc: qcom: socinfo: Fixed argument passed to platform_set_data()
Link: https://lore.kernel.org/r/20210930025456.1035-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM64 DTS fixes for 5.15
This starts by reverting the SC7280 CPUfreq update, which was merged
before concensus about the associated drivers changes was reached.
It then moves the reserved-memory changes done to get IPA working on the
Lenovo Yoga C630 into the Yoga specific DTS, as changing the memory map
on the platform level did break a couple of the other boards.
It fixes the HDMI audio on Trogdor and add missing Aggre2 NOC qos clocks
on SDM6{30,36,60} which prevented some boards from booting.
Lastly it enables the PON module on SM8250/QRB5165, as the lack thereof
is blocking automated testing in LKFT.
* tag 'qcom-arm64-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sdm630: Add missing a2noc qos clocks
arm64: dts: qcom: qrb5165-rb5: enabled pwrkey and resin nodes
arm64: dts: qcom: pm8150: specify reboot mode magics
arm64: dts: qcom: pm8150: use qcom,pm8998-pon binding
arm64: dts: qcom: sc7180-trogdor: Fix lpass dai link for HDMI
arm64: dts: qcom: sdm850-yoga: Reshuffle IPA memory mappings
Revert "arm64: dts: qcom: sc7280: Fixup the cpufreq node"
Link: https://lore.kernel.org/r/20210930025509.1091-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Juno/Vexpress fixes for v5.15
Bunch of DTS fixes to resolve addressing issues with some of the device
nodes, dropping unused/undocumented properties in various nodes, and
aligning node names with dtschema.
* tag 'juno-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm: dts: vexpress: Fix motherboard bus 'interrupt-map'
arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes
arm: dts: vexpress-v2p-ca9: Fix the SMB unit-address
arm: dts: vexpress: Drop unused properties from motherboard node
arm64: dts: arm: drop unused interrupt-names in MHU
ARM: dts: arm: align watchdog and mmc node names with dtschema
arm64: dts: arm: align watchdog and mmc node names with dtschema
arm64: dts: fvp: Remove panel timings
Link: https://lore.kernel.org/r/20210927105249.3583380-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm DTS fixes for v5.15
This corrects the use of depricated chipid and clock names, for which
support was finally dropped from the driver. It also ensures that the
DSI PLL is fed by the correct clock, now that it's being migrated to not
rely on global clock names.
* tag 'qcom-dts-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: apq8064: update Adreno clock names
ARM: dts: qcom: apq8064: Use 27MHz PXO clock as DSI PLL reference
ARM: dts: qcom: apq8064: use compatible which contains chipid
Link: https://lore.kernel.org/r/20210930025526.1146-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes
AT91 fixes #2 for 5.15:
- More fixes for AT91 platform power management code related to the
introduction of sama7g5:
- management of DDR3L regulator rails for sama7g5ek
- loading of TLB on different cores
- PIO controller slew-rate settings for sama7g5ek: be aligned with
datasheet requirements.
* tag 'at91-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
ARM: at91: pm: preload base address of controllers in tlb
ARM: at91: pm: group constants and addresses loading
ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail
Link: https://lore.kernel.org/r/20211004114344.19304-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add Vignesh to TI K3 platform maintainership. We will rotate roles for
each kernel version to help spread the work load a little better.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210915121308.26795-1-nm@ti.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes
Fix OP-TEE shm_pool lint warning
* tag 'optee-fix-for-v5.15' of git://git.linaro.org/people/jens.wiklander/linux-tee:
tee/optee/shm_pool: fix application of sizeof to pointer
Link: https://lore.kernel.org/r/20210915113813.GA509196@jade
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix invalid M2_RST# gpio pinmux.
Fixes: ef484dfcf6f7 ("arm64: dts: imx: Add i.mx8mm/imx8mn Gateworks gw7902 dts support")
Cc: stable@vger.kernel.org
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Any pending interrupt can prevent entering standby based power off state.
To avoid it, disable the GIC CPU interface.
Fixes: 8148d2136002 ("ARM: imx6: register pm_power_off handler if "fsl,pmic-stby-poweroff" is set")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On the LS1028A this instance of the eSDHC controller is intended for
either an eMMC or eSDIO card. It doesn't provide a card detect pin and
its IO voltage is fixed at 1.8V.
Remove the bogus broken-cd property, instead add the non-removable
property. Fix the voltage-ranges property and set it to 1.8V only.
Fixes: 491d3a3fc113 ("arm64: dts: ls1028a: Add esdhc node in dts")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The buck2 output of the PMIC is the VDD core voltage of the cpu.
Switching off this will poweroff the CPU. Add the 'regulator-always-on'
property to avoid this.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
With commit c709135e576b ("pinctrl: at91-pio4: add support for slew-rate")
and commit cbde6c823bfa ("pinctrl: at91-pio4: Fix slew rate disablement")
the slew-rate is enabled by default for each configured pin. The datasheet
specifies at chapter "Output Driver AC Characteristics" that HSIO
drivers (use in SDMMCx and QSPI0 peripherals), don't have a slewrate
setting but are rather calibrated against an external 1% resistor mounted
on the SDMMCx_CAL or QSPI0_CAL pins. Depending on the target signal
frequency and the external load, it is possible to adjust their target
output impedance. Thus set slew-rate = <0> for SDMMC (QSPI is not enabled
at the moment in device tree).
Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-3-claudiu.beznea@microchip.com
|
|
Datasheet chapter "EMAC Timings" specifies that while in 3.3V domain
GMAC's MDIO pins should be configured with slew-rate enabled, while the
data + signaling pins should be configured with slew-rate disabled when
GMAC works in RGMII or RMII modes. The pin controller for SAMA7G5 sets
the slew-rate as enabled for all pins. Adapt the device tree to comply
with these.
Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-2-claudiu.beznea@microchip.com
|
|
In suspend/resume procedure for AT91 architecture different controllers
(PMC, SHDWC, RAM, RAM PHY, SFRBU) are accessed to do the proper settings
for power saving. Commit f0bbf17958e8 ("ARM: at91: pm: add self-refresh
support for sama7g5") introduced the access to RAMC PHY controller for
SAMA7G5. The access to this controller is done after RAMC ports are
closed, thus any TLB walk necessary for RAMC PHY virtual address will
fail. In the development branch this was not encountered. However, on
current kernel the issue is reproducible.
To solve the issue the previous mechanism of pre-loading the TLB with
the RAMC PHY virtual address has been used. However, only the addition
of this new pre-load breaks the functionality for ARMv5 based
devices (SAM9X60). This behavior has been encountered previously
while debugging this code and using the same mechanism for pre-loading
address for different controllers (e.g. pin controller, the assumption
being that other requested translations are replaced from TLB).
To solve this new issue the TLB flush + the extension of pre-loading
the rest of controllers to TLB (e.g. PMC, RAMC) has been added. The
rest of the controllers should have been pre-loaded previously, anyway.
Fixes: f0bbf17958e8 ("ARM: at91: pm: add self-refresh support for sama7g5")
Depends-on: e42cbbe5c9a2 ("ARM: at91: pm: group constants and addresses loading")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-4-claudiu.beznea@microchip.com
|
|
Group constants and addresses loading. This commit prepares the field for
the next one.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-3-claudiu.beznea@microchip.com
|
|
SAMA7G5-EK board has DDR3L type of memory soldered. This needs 1.35V. The
1.35V for DDR3L rail at run-time is selected by the proper configuration
on SELV2 pin (for 1.35V it needs to be in high-z state). When suspended
the MCP16502 PMIC soldered on SAMA7G5-EK will use different sets of
configuration registers to provide proper voltages on its rail. Run-time
configuration registers could be configured differently than suspend
configuration register for MCP16502 (VSEL2 affects only run-time
configuration). In suspend states the DDR3L memory soldered on SAMA7G5-EK
switches to self-refresh. Even on self-refresh it needs to be powered by
a 1.35V rail. Thus, make sure the PMIC is configured properly when system
is suspended.
Fixes: 7540629e2fc7 (ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-2-claudiu.beznea@microchip.com
|
|
Before commit 0e30f47232ab5 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.
qspi and fspi host controller do not support read 1-4-4 mode. so need to
set the tx to 1, let the common code finally select read 1-1-4 mode.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 0e30f47232ab ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Before commit 0e30f47232ab5 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.
Though the spi-nor device on imx6sx-sdb/imx6ul(l/z)-14x14-evk board
do not support PP-1-4-4/PP-1-1-4, but if tx is 4 in dts file, it will also
impact the read mode selection. For the spi-nor device on the upper mentioned
boards, they support read 1-4-4 mode and read 1-1-4 mode according to the
device internal sfdp register. But qspi host controller do not support
read 1-4-4 mode. so need to set the tx to 1, let the common code finally
select read 1-1-4 mode, PP-1-1-1 mode.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 0e30f47232ab ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Starting with v5.15-rc1, we may now see some am335x beaglebone black
device produce the following error on pruss probe:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xe0326000
This has started with the enabling of pruss for am335x in the dts files.
Turns out the is caused by the PRM reset handling not waiting for the
reset bit to clear. To fix the issue, let's always wait for the reset
bit to clear, even if there is a separate reset status register.
We attempted to fix a similar issue for dra7 iva with a udelay() in
commit effe89e40037 ("soc: ti: omap-prm: Fix occasional abort on reset
deassert for dra7 iva"). There is no longer a need for the udelay()
for dra7 iva reset either with the check added for reset bit clearing.
Cc: Drew Fustini <pdp7pdp7@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Yongqin Liu <yongqin.liu@linaro.org>
Fixes: effe89e40037 ("soc: ti: omap-prm: Fix occasional abort on reset deassert for dra7 iva")
Reported-by: Matti Vaittinen <mazziesaccount@gmail.com>
Tested-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 078fb7aa6a83 ("arm: dts: vexpress: Fix addressing issues with
'motherboard-bus' nodes") broke booting on a couple of 32-bit VExpress
boards. The problem is #address-cells size changed, but interrupt-map
was not updated. This results in the timer interrupt (and all the
other motherboard interrupts) not getting mapped.
As the 'interrupt-map' properties are all just duplicates across boards,
just move them into vexpress-v2m.dtsi and vexpress-v2m-rs1.dtsi.
Strictly speaking, 'interrupt-map' is dependent on the parent
interrupt controller, but it's not likely we'll ever have a different
parent than GICv2 on these old platforms. If there was one,
'interrupt-map' can still be overridden.
Link: https://lore.kernel.org/r/20210924214221.1877686-1-robh@kernel.org
Fixes: 078fb7aa6a83 ("arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes")
Cc: Guillaume Tucker <guillaume.tucker@collabora.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Reported-by: Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
It adds the missing a2noc clocks required for QoS registers programming
per downstream kernel[1].
[1] https://source.codeaurora.org/quic/la/kernel/msm-4.4/tree/arch/arm/boot/dts/qcom/sdm660-bus.dtsi?h=LA.UM.8.2.r1-04800-sdm660.0#n43
Fixes: 045547a02252 ("arm64: dts: qcom: sdm630: Add interconnect provider nodes")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210824043435.23190-4-shawn.guo@linaro.org
|
|
Enable powerkey and resin nodes to let the board handle POWER and
Volume- keys properly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210916151341.1797512-3-dmitry.baryshkov@linaro.org
|
|
Specify recovery and bootloader magic values to be programmed by the
qcom-pon driver. This allows the bootloader to handle
reboot-to-bootloader functionality.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210916151341.1797512-2-dmitry.baryshkov@linaro.org
|
|
Change pm8150 to use the qcom,pm8998-pon compatible string for the pon
in order to pass reboot mode properly.
Fixes: 5101f22a5c37 ("arm64: dts: qcom: pm8150: Add base dts file")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210916151341.1797512-1-dmitry.baryshkov@linaro.org
|
|
Enable CONFIG_FB which is nowadays required for CONFIG_DRM_PANEL_LVDS,
CONFIG_DRM_PANEL_SIMPLE, CONFIG_DRM_PANEL_SEIKO_43WVF1G,
CONFIG_FB_MODE_HELPERS, CONFIG_BACKLIGHT_PWM, CONFIG_BACKLIGHT_GPIO,
CONFIG_FRAMEBUFFER_CONSOLE, CONFIG_LOGO, CONFIG_FONTS, CONFIG_FONT_8x8
and CONFIG_FONT_8x16.
Fixes: f611b1e7624c ("drm: Avoid circular dependencies for CONFIG_FB")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently, it is no longer possible to retrieve a DHCP address
on the imx6qdl-pico board.
This issue has been exposed by commit f5d9aa79dfdf ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 98670a0bb0ef14bbb3 ("ARM: dts: imx6qdl: Add imx6qdl-pico support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The MIC2025 switch input signal nEN is active low, describe it as such
in the DT. The previous change to this regulator polarity was incorrectly
influenced by broken quirks in gpiolib-of.c, which is now long fixed. So
fix this regulator polarity setting here once and for all.
Fixes: 3c3601cd6a6d3 ("ARM: dts: imx53: Update USB configuration on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The panel already contains pinctrl-0 phandle, but it is missing
the default pinctrl-names property, so the pin configuration is
ignored. Fill in the missing pinctrl-names property, so the pin
configuration is applied.
Fixes: d81765d693db6 ("ARM: dts: imx53: Update LCD panel node on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This reverts commit cc8870bf4c3ab0af385538460500a9d342ed945f.
Since commit cc8870bf4c3a ("ARM: imx6q: drop of_platform_default_populate()
from init_machine") the following errors are seen on boot:
[ 0.123372] imx6q_suspend_init: failed to find ocram device!
[ 0.123537] imx6_pm_common_init: No DDR LPM support with suspend -19!
, which break suspend/resume on imx6q/dl.
Revert the offeding commit to avoid the regression.
Thanks to Tim Harvey for bisecting this problem.
Cc: stable@vger.kernel.org
Fixes: cc8870bf4c3a ("ARM: imx6q: drop of_platform_default_populate() from init_machine")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since the LED multicolor framework support was added in commit
92a81562e695 ("leds: lp55xx: Add multicolor framework support to lp55xx")
LEDs on this platform stopped working.
Author of the framework attempted to accommodate this DT to the
framework in commit b86d3d21cd4c ("ARM: dts: imx6dl-yapp4: Add reg property
to the lp5562 channel node") but that is not sufficient. A color property
is now required even if the multicolor framework is not used, otherwise
the driver probe fails:
lp5562: probe of 1-0030 failed with error -22
Add the color property to fix this.
Fixes: 92a81562e695 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Cc: <stable@vger.kernel.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
virtio_scmi_exit() is only called from __exit function, so the annotation
is correct, but when the driver is built-in, the section gets discarded
and the reference from a callback pointer causes a link-time error:
`virtio_scmi_exit' referenced in section `.rodata' of drivers/firmware/arm_scmi/virtio.o:
defined in discarded section `.exit.text' of drivers/firmware/arm_scmi/virtio.o
I could not figure out a better workaround, so let's just remove that
annotation even if it wastes a couple of bytes in .text.
Link: https://lore.kernel.org/r/20210920100301.1466486-2-arnd@kernel.org
Fixes: 46abe13b5e3d ("firmware: arm_scmi: Add virtio transport")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
ARM_SCMI_TRANSPORT_VIRTIO is a 'bool' Kconfig used to include support for
the SCMI virtio transport inside the core SCMI stack; a bare transport
dependency attached here to this option, though, cannot be properly
propagated to the parent ARM_SCMI_PROTOCOL option and, as a result, it is
currently possible to configure a Kernel where SCMI core is builtin
and includes support for virtio while VirtIO core is =m.
This allowed combination breaks linking:
ARM_SCMI_PROTOCOL=y
ARM_SCMI_TRANSPORT_VIRTIO=y
VIRTIO=m
Bind the dependency in ARM_SCMI_TRANSPORT_VIRTIO to the chosen kind of
compilation of ARM_SCMI_PROTOCOL.
Link: https://lore.kernel.org/r/20210816141609.41751-1-cristian.marussi@arm.com
Fixes: 46abe13b5e3d ("firmware: arm_scmi: Add virtio transport")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
This should be the dai for display port. Without this set properly we
fail to get audio routed through external displays on trogdor. It looks
like we picked up v4[1] of this patch when there was a v7[2]. The v7
patch still had the wrong sound-dai but at least we can fix all this up
and audio works.
Cc: Srinivasa Rao Mandadapu <srivasam@qti.qualcomm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: b22d313e1772 ("arm64: dts: qcom: sc7180-trogdor: Add lpass dai link for HDMI")
Link: https://lore.kernel.org/r/20210721080549.28822-3-srivasam@qti.qualcomm.com [1]
Link: https://lore.kernel.org/r/20210726120910.20335-3-srivasam@codeaurora.org [2]
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210811224141.1110495-1-swboyd@chromium.org
|
|
The legacy clock names (including the _clk suffix) was dropped from the
driver, so update the dts accordingly).
Tested on Nexus 7 2013, no functional changes.
Signed-off-by: David Heidelberg <david@ixit.cz>
[bjorn: Updated commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210829133918.57780-2-david@ixit.cz
|
|
The Qualcomm Secure Channel Manager (SCM) is only present on Qualcomm
SoCs. All drivers using it select QCOM_SCM, and depend on ARCH_QCOM.
Until recently, QCOM_SCM was an invisible symbol, but this was changed
by adding loadable module support, exposing it to all ARM and ARM64
users. Hence add a dependency on ARCH_QCOM, to prevent asking the user
about this driver when configuring a kernel without Qualcomm SoC
support.
While at it, drop the dependency on ARM || ARM64, as that is implied by
HAVE_ARM_SMCCC.
Fixes: b42000e4b8741bf6 ("firmware: qcom_scm: Allow qcom_scm driver to be loadable as a permenent module")
Fixes: 2954a6f12f250890 ("firmware: qcom-scm: Fix QCOM_SCM configuration")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/5cda77085c07dc2e8d2195507b287457cb2f09e9.1629807831.git.geert+renesas@glider.be
|
|
PT_LOAD type denotes that the segment should be loaded into the final
firmware memory region. Hash segment is not one such, because it's only
needed for PAS init and shouldn't be in the final firmware memory region.
That's why mdt_phdr_valid() explicitly reject non PT_LOAD segment and
hash segment. This actually makes the hash segment type check in
qcom_mdt_read_metadata() unnecessary and redundant. For a hash segment,
it won't be loaded into firmware memory region anyway, due to the
QCOM_MDT_TYPE_HASH check in mdt_phdr_valid(), even if it has a PT_LOAD
type for some reason (misusing or abusing?).
Some firmware files on Sony phones are such examples, e.g WCNSS firmware
of Sony Xperia M4 Aqua phone. The type of hash segment is just PT_LOAD.
Drop the unnecessary hash segment type check in qcom_mdt_read_metadata()
to fix firmware loading failure on these phones, while hash segment is
still kept away from the final firmware memory region.
Fixes: 498b98e93900 ("soc: qcom: mdt_loader: Support loading non-split images")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210828070202.7033-1-shawn.guo@linaro.org
|
|
Upstream commit 2e01e0c21459 ("arm64: dts: qcom: sdm850-yoga:
Enable IPA") shuffled reserved memory regions in sdm845.dtsi
to make firmware loading succeed and enable the ipa device on
sdm845-yoga but it broke the other common users of those
memory regions like Xiaomi Pocophone F1.
So this patch effectively revert those upstream commit changes
and move all the relevant changes to sdm850-lenovo-yoga-c630.dts
instead.
Fixes: 2e01e0c21459 ("arm64: dts: qcom: sdm850-yoga: Enable IPA")
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210916200554.2434439-1-amit.pundir@linaro.org
|
