summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-08-13ath10k: Enable MU MIMO txbf support for QCA99X0Vivek Natarajan
This patch enables MU-MIMO transmit beamforming support for QCA99X0 chipsets. Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-13ath10k: Support different txbf configuration schemesVivek Natarajan
qca61x4 uses the vdev param as a sole sufficient configuration for txbf while qca99x0 enables txbf during peer assoc by combining the vdev param value with peer assoc's vht capabilities This patch gets the appropriate txbf configuration scheme before passing the wmi command to enable the same in the firmware. Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-13ath10k: reject 11b tx fragmentation configurationMichal Kazior
Even though there's a WMI enum for fragmentation threshold no known firmware actually implements it. Moreover it is not possible to rely frame fragmentation to mac80211 because firmware clears the "more fragments" bit in frame control making it impossible for remote devices to reassemble frames. Hence implement a dummy callback just to say fragmentation isn't supported. This effectively prevents mac80211 from doing frame fragmentation in software. This fixes Tx becoming broken after setting fragmentation threshold. Fixes: 1010ba4c5d1c ("ath10k: unregister and remove frag_threshold callback") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-13ath10k: remove futile fragmentation threshold configMichal Kazior
Commit 1010ba4c5d1c ("ath10k: unregister and remove frag_threshold callback") didn't remove all instances of (futile) fragmentation threshold configuration. No known firmware supports the parameter so don't even bother setting it. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-10ath: Make ath_opmode_to_string understand OCB modeBertold Van den Bergh
Make ath_opmode_to_string return "OCB" for NL80211_IFTYPE_OCB. Currently it will return "UNKNOWN". Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10bcma: fix access to host_pdev for PCIe devicesHauke Mehrtens
bus->host_pdev is part of a union so bus->host_pdev != NULL is probably also true for PCIe devices, because there it accesses bus->host_pci. If we access the dev member at the offset defined in struct platform_device in struct pci_dev instead we probably get something else. This patch adds a new function which returns the host dev struct and NULL if we do not have a host dev. When this gets registered on MIPS brcm47xx we do not have a host dev in some situations. This function could also be used in other places. This problem was introduced in this commit: commit cae761b5a6bdc597ba476a040fdcd5b4bc559b85 Author: Rafa? Mi?ecki <zajec5@gmail.com> Date: Sun Jun 28 17:17:13 2015 +0200 bcma: populate bus DT subnodes as platform_device-s Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10mt7601u: lock out rx path and tx status reportingJakub Kicinski
mac80211 requires that rx path does not run concurrently with tx status reporting. Add a spinlock which will ensure that. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10mt7601u: fix tx status reporting contextsJakub Kicinski
mac80211 requires that rx path does not run concurrently with tx status reporting. Since rx path is run in driver tasklet, tx status cannot be reported directly from interrupt context (there would be no way to lock it out). Add tasklet for tx and move all possible code from irq handler there. Note: tx tasklet is needed because workqueue is queued very rarely and that kills TCP performance. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10mt7601u: use correct ieee80211_rx variantJakub Kicinski
Rx is run inside a tasklet so ieee80211_rx() should be used instead of ieee80211_rx_ni(). Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10mt7601u: fix dma from stack addressJakub Kicinski
DMA to variables located on the stack is a bad idea. For simplicity and to avoid frequent allocations create a buffer inside the device structure. Protect this buffer with vendor_req_mutex. Don't protect vendor requests which don't use this buffer. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10wlcore: add p2p device supportEliad Peller
When starting a p2p mgmt interface, enable its device role. This allows us to keep the sta role disabled and scan on the dev role. In general, p2p management interfaces cannot send vif-specific commands to FW, as the vif role id is invalid. Only off-channel data and scans happen on this vif, so most ops are not relevant. If the vif is a p2p mgmt vif, block some mac80211 ops. Configure rate policies for p2p mgmt interface, as otherwise p2p packets come out with arbitrary rates. Since wpa_supplicant currently doesn't support standalone p2p device mode (without another attached managed interface), add p2p device to the allowed interface combinations without decreasing the allowed station count. Moreover, increase the station count in some cases, as AP mode usually starts as station interface, and the AP interface is now different from the p2p management one). Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10wlcore: add generic_cfg_feature command definitionsEliad Peller
Add definitions and function prototypes for generic_cfg command. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10wl18xx: use long intervals in sched scanEliad Peller
Add support for long intervals on sched scan. If configured, the original request interval will be used num_short_interval times, and then the long interval will be used. While on it, fix the scan command field names to reflect the expected value is in ms (rather than secs). These values will be taken from the conf file, so bump its version accordingly. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10wlcore/wl18xx : add time sync event handlingMachani, Yaniv
Added support for a new time sync event the event data contains the WiLink TSF value. To trigger the event, a HW modification is required, so as a supporting firmware binary. Signed-off-by: Yaniv Machani <yanivma@ti.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10mwifiex: correct TDLS link delete failure message priorityAmitkumar Karwar
Commit d8d2f19feb16 ("mwifiex: silence TDLS link delete failure for nonexistent link") lowers the priority of error message when TDLS link is already deleted. But it had got increased by commit acebe8c10a6e ("mwifiex: change dbg print func to mwifiex_dbg") Reported-by: Nicholas Mc Guire <der.herr@hofr.at> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-07ath9k: fix build with CONFIG_ATH9K_STATION_STATISTICS=yFelix Fietkau
kbuild bot reported that commit 592fa228f213 ("ath9k: remove struct ath_atx_ac") broke the build when CONFIG_ATH9K_STATION_STATISTICS is y. Reported-by: kbuild test robot <fengguang.wu@intel.com> Fixes: 592fa228f213 ("ath9k: remove struct ath_atx_ac") Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06Merge tag 'iwlwifi-next-for-kalle-2015-08-04' of ↵Kalle Valo
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next * Deprecate -10.ucode * Clean ups towards multiple Rx queues * Add support for longer CMD IDs. This will be required by new firmwares since we are getting close to the u8 limit. * bugfixes for the D0i3 power state * Add basic support for FTM * More random that doesn't really stand out
2015-08-06wlcore: add antenna diversity reading commentsGuy Mishol
add comments to the antenna diversity reading Signed-off-by: Guy Mishol <guym@ti.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06mwifiex: add missing skb_push() in mwifiex_check_uap_capabiltiesAmitkumar Karwar
For PCIe/USB chipsets, preallocated skb buffers are reused for event handling. mwifiex_check_uap_capabilties() performs skb_pull(). This patch adds missing skb_push() to restore skb's data pointer/length. This bug was introduced by commit debfc6008169 ("mwifiex: update AP WMM settings from BSS_START event") Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06wl18xx: add dynamic fw tracesGuy Mishol
add option to dynamically configure the fw which debug traces to open Signed-off-by: Guy Mishol <guym@ti.com> Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06mwifiex: corrections in PCIe event skb handlingAmitkumar Karwar
Preallocated event SKBs are getting reused for PCIe chipset. Their physical addresses are shared with firmware so that firmware can write data into them. This patch makes sure that SKB is cleared and length is set to default while submitting it to firmware. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Zhaoyang Liu <liuzy@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06mwifiex: fix system crash observed during initialisationZhaoyang Liu
System crash was observed if one of the driver initialisation commands is timed out. The reason is our timeout handler triggers firmware dump, meanwhile driver initialisation error paths have already freed the adapter structure. Firmware hasn't yet completely initialized. So collecting firmware dump is not needed in this case. Command timeout handler is modified in this patch to fix the crash issue. Signed-off-by: Zhaoyang Liu <liuzy@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06mwifiex: fix command timeout for PCIe chipsetsZhaoyang Liu
When WLAN interface is up and running, driver unload and load was causing command timeout error. We enable Rx data by updating RX ring read pointer in init_fw_port(). It should be done when FW is completely intialialised. Command timeout is fixed in this patch by moving init_fw_port() call to mwifiex_init_fw_complete(). Signed-off-by: Zhaoyang Liu <liuzy@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06mwifiex: using right aid value for tdls action frameXinming Hu
Variable pos is u8 here, so memcpy is needed to store u16 aid. At the same time, aid should be platform independent, upper layer utility(wpa_supplicant,etc.,) parse it as le16, so keep it le16 here. Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06ath9k: remove the sched field in struct ath_atx_tidFelix Fietkau
Use list_empty(&tid->list) instead Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06ath9k: remove struct ath_atx_acFelix Fietkau
struct ath_atx_ac contains a list of active TIDs belonging to one WMM AC. This patch changes the code to track active station TIDs in the txq directly. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06ath9k: add fast-xmit supportFelix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06ath9k: setup rxfilter when offchannelJanusz.Dziedzic@tieto.com
Setup rxfiler correctly for offchannel ctx. This fix problem we didn't configure rxfilter, next didn't receive probe requests and next failed p2p_find. This was seen when ath9k loaded with use_chanctx=1 Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06ath9k: setup rxfilter for all chanctxJanusz.Dziedzic@tieto.com
While mac80211 setup this per HW, set same rxfilter configuration for all chanctx. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06ath9k: handle RoC cancel correctlyJanusz.Dziedzic@tieto.com
In case we will get ROC cancel from mac80211 we should not call ieee80211_remain_on_channel_expired(). In other case I hit such warning on MIPS and p2p negotiation failed (tested with use_chanctx=1). ath: phy0: Starting RoC period ath: phy0: Channel definition created: 2412 MHz ath: phy0: Assigned next_chan to 2412 MHz ath: phy0: Offchannel duration for chan 2412 MHz : 506632 ath: phy0: ath_chanctx_set_next: current: 2412 MHz, next: 2412 MHz ath: phy0: Stopping current chanctx: 2412 ath: phy0: Flush timeout: 200 ath: phy0: ath_chanctx_set_next: Set channel 2412 MHz ath: phy0: Set channel: 2412 MHz width: 0 ath: phy0: Reset to 2412 MHz, HT40: 0 fastcc: 0 ath: phy0: cur_chan: 2412 MHz, event: ATH_CHANCTX_EVENT_TSF_TIMER, state: ATH_CHANCTX_STATE_IDLE ath: phy0: ath_offchannel_channel_change: offchannel state: ATH_OFFCHANNEL_ROC_START ath: phy0: cur_chan: 2412 MHz, event: ATH_CHANCTX_EVENT_SWITCH, state: ATH_CHANCTX_STATE_IDLE ath: phy0: Cancel RoC ath: phy0: RoC aborted ath: phy0: RoC request on vif: 00:03:7f:4e:a0:cd, type: 1 duration: 500 ath: phy0: Starting RoC period ath: phy0: Channel definition created: 2412 MHz ath: phy0: Assigned next_chan to 2412 MHz ath: phy0: Offchannel duration for chan 2412 MHz : 506705 ath: phy0: ath_chanctx_set_next: current: 2412 MHz, next: 2412 MHz ath: phy0: ath_offchannel_channel_change: offchannel state: ATH_OFFCHANNEL_ROC_START ath: phy0: cur_chan: 2412 MHz, event: ATH_CHANCTX_EVENT_SWITCH, state: ATH_CHANCTX_STATE_IDLE ------------[ cut here ]------------ WARNING: CPU: 0 PID: 3312 at drivers/net/wireless/ath/ath9k/main.c:2319 Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06ath9k: advertise p2p dev support when chanctxJanusz.Dziedzic@tieto.com
Advertise p2p device support when ath9k loaded with use_chanctx=1. This will fix problem, when first interface is an AP and next we would like to run p2p_find. Before p2p find (scan phase) failed with EOPNOTSUPP. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06mwifiex: simplify mwifiex_complete_cmdAndreas Fenkart
600f5d909a54("mwifiex: cleanup ioctl wait queue and abstraction layer") introduced the wakeup_interruptible suppression in mwifiex_complete_cmd b1a47aa5e1e1("mwifiex: fix system hang issue in cmd timeout error case") then added wakup_interruptible to mwifiex_cmd_timeout_func the single place setting a status of ETIMEDOUT. Instead of doing extra work, using the standard call-chain will have the same effect: mwifiex_cancel_pending_ioctl -> mwifiex_recycle_cmd_node -> mwifiex_insert_cmd_to_free_q -> mwifiex_complete_cmd -> wake_up_interruptible The difference is that previously the condition was not set to true, but that's probably just an oversight in b1a47aa5e1e1 and shouldn't have any consequence Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06mwifiex: remove CMD_F_CANCELED flagAndreas Fenkart
CMD_F_CANCELED was used to abort mwifiex_process_cmdresp in case it already started or starts processing the cmd. But this was probably not working the way intended: - it is racy: mwifiex_process_cmdresp might already have passed that test and is continuing to use the cmd node being recycled - mwifiex_process_cmdresp repeatedly uses adapter->curr_cmd which we just set to NULL - mwifiex_recycle_cmd_node will clear the flag The reason why it probably works is that mwifiex_cancel_pending_ioctl is only called from mwifiex_cmd_timeout_func, where the there is little chance of a command response still arriving Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06mwifiex: remove redundant reset of cmd_wait_q statusAndreas Fenkart
mwifiex_cancel_pending_ioctl is called only from mwifiex_cmd_timeout_func. There the wait_q status is set to -ETIMEDWAIT before calling this function. Whether we reset the status to -1 or leave it at -ETIMEDWAIT at end doesn't matter since both are != 0 hence mean failure Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06mwifiex: remove explicit mwifiex_complete_cmd callsAndreas Fenkart
standard call chain when releasing a cmd node: mwifiex_recycle_cmd_node -> mwifiex_insert_cmd_to_free_q -> mwifiex_complete_cmd, if wait_q_enabled calling mwifiex_complete_cmd explicitly and setting wait_q_enabled = false is redundant Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06mwifiex: sdio: reset adapter using mmc_hw_resetAndreas Fenkart
Since 1fb654fd97ff("mmc: sdio: add reset callback to bus operations"), sdio cards can be power cycled using mmc_hw_reset. The use mmc_remove_host/mmc_add_host is discouraged, because these are internal functions to the mmc core and should only be used by mmc hosts Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-06wil6210: support future boot loadersVladimir Kondratiev
Boot loader versions as backward compatible, starting from v1 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: report boot loader errorVladimir Kondratiev
Boot loader reports error starting from the struct v2. Print error info before reset (power up state) in debug mode, and print same info as error if target reset timed out. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: system power managementVladimir Kondratiev
Support for the system suspend/resume. In preparation for the run-time PM, implementation made run-time PM friendly: common for system and run-time PM code factored out as generic functions, albeit is_runtime parameter value is always false currently. For debug purposes, "PM" debug category introduced. Policy: AP-like interface can't be suspended; otherwise suspend is allowed. Hardware brought down if interface was up. Connection, if existed, get lost. Interface will be brought up upon resume if it was up before suspend. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: allow to handle Rx on 2 coresVladimir Shulman
Allow network stack part of Rx processing to run on separate core, relaxing CPU utilization on the core used for Rx NAPI. If RXHASH feature is enabled, the driver sets rxhash of each skb to 1 to enable RPS. The core for processing the rx skb is determined by RPS mechanism according to rx_cpus bit mask which is configured at user level. For processing skbs on different core from the core which processes the interrupts, it is recommended not to enable core 0 in rx_cpus bit mask. Signed-off-by: Vladimir Shulman <QCA_shulmanv@QCA.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: use inline functions for register accessVladimir Kondratiev
Replace macros like "R", "W", "S", "C", defined multiple times, with inline functions "wil_[rwsc]". Use "readl" and "writel" instead of "ioread32" and "iowrite32" since it is granted that memory transactions are used, not port ones like IN/OUT Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: remove 3-MSI supportVladimir Kondratiev
In the recent kernel versions, multiple MSI is not well supported. In particular, it is not supported on x86 and ARM architectures. Also, internal interrupt handling logic is simpler and more effective when using single interrupt. Remove support for 3 MSI, convert module parameter "use_msi" from int with range [0,1,3] to boolean. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: detailed statistics for Rx reorder dropVladimir Kondratiev
Rx drops may be for 2 reasons: frame is old, or it is duplicate. On the debugfs "stations" entry, provide counters per reorder buffer for total frames processed, drops for these 2 reasons. Also add debug print for dropped frames. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: unify wmi_set_ie() error handlingVladimir Kondratiev
When printing error message, provide string describing IE kind. Derive it from IE type This allows removing of error messages printing in callers Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: sort IEs handlingVladimir Kondratiev
sort overall IE's handling prepare code (disabled for now) to add IEs for the beacon Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: treat "unhandled event" as warning instead of errorDedy Lansky
FW is allowed to generate WMI events that are not handled by this driver. Treat such case as warning instead of error. Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: improve mgmt frame handlingVladimir Kondratiev
Check event length; hex dump both Rx and Tx frames Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: TSO implementationVladimir Kondratiev
Driver report supported TSO (v4 & v6) and IP checksum offload in addition to previously supported features. In data path skbs are checked for non-zero gso_size, and when detected sent to additional function for processing TSO SKBs. Since HW does not fully support TSO, additional effort is required from the driver. Driver partitions the data into mss sized descriptors which are then DMAed to the HW. Signed-off-by: Vladimir Shulman <QCA_shulmanv@QCA.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: skip HW version check for chip debuggingVladimir Kondratiev
When loading with debug_fw flag, do not bail out on unknown chipId Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-06wil6210: use wil_fw_error_recovery()Vladimir Kondratiev
Use function wil_fw_error_recovery() instead of inline equivalent code Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-29 08:47:50 +0000