| Age | Commit message (Collapse) | Author |
|---|
|
One of the pins of i2c2 is actually in use as chip select 0 for spi0.
The chip select 0 is used for an FRAM chip, which will be added in the
next patch.
Remove the i2c2 node from the rk3568-mecsbc device tree.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Jonas Rebmann <jre@pengutronix.de>
Link: https://lore.kernel.org/r/20241219-mb85rs128ty-mecsbc-v1-1-77a0e851ef19@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Edgeble 6TOPS modules has configured the PCIe3.0 with
- 2 lanes on Port1 of pcie3x2 controller for M.2 M-Key
- 2 lanes on Port0 of pcie3x4 controller for B and E-Key
The, current DT uses opposite controller nodes that indeed uses
incorrect reset, regulator nodes.
The configuration also uses refclk oscillator that need to enable
explicitly in DT to avoid the probe hang on while reading DBI.
So, this patch fixes all these essential issues and make this PCIe work
properly.
Issues fixed are,
- Fix the associate controller nodes for M and B, E-Key
- Fix the reset gpio handlings
- Fix the regulator handlings and naming convensions
- Support pcie_refclk oscillator
Fixes: 92eaee21abbd ("arm64: dts: rockchip: Add Edgeble NCM6A-IO M.2 B-Key, E-Key")
Fixes: 5d85d4c7e03b ("arm64: dts: rockchip: Add Edgeble NCM6A-IO M.2 M-Key")
Reported-by: Mitchell Ma <machuang@radxa.com>
Co-developed-by: Mitchell Ma <machuang@radxa.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20241221151758.345257-1-jagan@edgeble.ai
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Radxa E52C[1] is a compact network computer based on the Rockchip
RK3582 SoC:
- Dual Cortex-A76 and quad Cortex-A55 CPU
- 5TOPS NPU
- 2GB/4GB/8GB LPDDR4 RAM
- 16GB/32GB/64GB on-board eMMC
- microSD card slot
- USB 3.0 Type-A HOST port
- USB Type-C debug port
- USB Type-C power port (5V only)
- 2x 2.5GbE ports
[1] https://radxa.com/products/network-computer/e52c
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20241226024630.13702-3-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add devicetree binding for the Radxa E52C.
Radxa E52C is a compact network computer based on the Rockchip RK3582
SoC.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20241226024630.13702-2-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
BigTreeTech CB2 and Pi2 share a lot of hardware configuration, so a
common dtsi file was used to define common nodes and properties. This is
similar to how BigTreeTech CB1 and Pi are implemented.
Signed-off-by: Ivan Sergeev <ivan8215145640@gmail.com>
Link: https://lore.kernel.org/r/20250106-bigtreetech-cb2-v7-2-565567e2c0a4@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
BigTreeTech CB2 and Pi2 are Rockchip RK3566 based boards
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Ivan Sergeev <ivan8215145640@gmail.com>
Link: https://lore.kernel.org/r/20250106-bigtreetech-cb2-v7-1-565567e2c0a4@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Orange Pi 5 Plus has its first USB 3.0 interface on the SoC wired
directly to the USB type C port next to the MASKROM button, and the
second interface wired to a USB 3.0 hub which in turn is connected to
the USB 3.0 host ports on the board, as well as the USB 2.0 connection
on the M.2 E-key slot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20241220161240.109253-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
H96 Max V58 is a compact Rockchip RK3588 based device that ships
with Android and is meant for use as a TV connected media box.
Its hardware includes:
- Rockchip RK3588 SoC with a small aluminium heatsink
- 4GB or 8GB LPDDR4 RAM
- 32GB or 64GB eMMC 5.1 storage (HS400)
- Onboard AP6275P wireless module providing 802.11ax 2x2 MIMO WiFi
over PCIe connection and Bluetooth 5.3 over UART with two external
detachable antennas
- 1x GbE using the onboard GMAC and an RTL8211F PHY
- 1x USB 2.0 Type-A (also serves as the Maskrom port)
- 1x USB 3.0 Type-A
- 1x HDMI 2.1 output
- 1x optical SPDIF output
- LED line display ("88:88" digits plus icons) driven by an FD6551
IC connected over bitbanged I2C (not yet enabled here)
- GPIO connected CIR receiver
- Single Rockchip RK806-1 PMIC
- 12x onboard ambient LEDs lighting up the bottom of the device
- 5v DCIN using a standard round 5.5mm connector
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20250108-rk3588-h96-max-v58-v2-3-522301b905d6@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add Devicetree binding for H96 Max V58: a compact Rockchip RK3588 based
device that ships with Android and is meant for use as a TV connected
media box.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20250108-rk3588-h96-max-v58-v2-1-522301b905d6@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
RK3576 EVB1 board features:
- Rockchip RK3576
- PMIC: RK806-2x2pcs+DiscretePower
- RAM: LPDDR4/4x 2pcsx 32bit
- ROM: eMMC5.1 + UFS
- LAN x 2
- HDMI TX
- SD card slot
- PCIe2 slot
Add support for pmic, eMMC, SD-card, ADC-KEY, PCIE and GMAC.
NOTE: The board has a hardware mux design for
- PCIe slot(pcie1)
- USB3 host(usb_drd1_dwc3)
and default state is switch to USB3. To enable PCIe slot:
- hardware: Switch the mux to PCIe side;
- dts: disable usb_drd1_dwc3 and enable pcie1;
Signed-off-by: Liang Chen <cl@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20250107074911.550057-8-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add device tree documentation for rk3576-evb1-v10.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250107074911.550057-7-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The board entries should be sort in correct order by the description
string.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250107074911.550057-6-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This adds USB and USB-PHY related nodes for RK3576 SoC.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20250107074911.550057-5-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
rk3576 has two naneng combo phys:
- combophy0 is used for one of pcie and sata;
- combophy1 is used for one of pcie, sata and usb3;
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20250107074911.550057-2-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add hdptxphy grf syscon compatibles for rk3576.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241231091841.252103-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The automatically generated names for the LEDs from color and function
do not match nicely for the 4 hdds, so set them manually per the label
property to also match the LEDs generated from the MCU.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241107114712.538976-10-heiko@sntech.de
|
|
The MCU is an important part of the device functionality. It provides
functionality like fan-control, more leds, etc and even more important
without it, the NAS-device cannot even fully turned off.
Hook up the serial device to its uart and hook into the thermal
management to control the fan according to the cpu temperature.
While the MCU also provides a temperature sensor for the case, this one
is just polled and does not provide functionality for handling trip
points in hardware, so a lot of polling would be involved.
As the cpu is only cooled passively in these devices, it's temperature
rising will indicate the temperature level of the system just earlier.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241107114712.538976-9-heiko@sntech.de
|
|
BootROM leave GPIO4_D6 configured as SDMMC_PWREN function and DW MCI
driver set PRWEN high on MMC_POWER_UP and low on MMC_POWER_OFF.
Similarly U-Boot also set PRWEN high before accessing mmc.
However, HW revision prior to v1.2 must pull GPIO4_D6 low to access
sdmmc. For HW revision v1.2 the state of GPIO4_D6 has no impact.
Model an always-on active low fixed regulator using GPIO4_D6 to fix
use of sdmmc on older HW revisions of the board.
Fixes: adeb5d2a4ba4 ("arm64: dts: rockchip: Add Radxa ROCK S0")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20241119230838.4137130-1-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Commit cd81d3a0695c ("arm64: dts: rockchip: add rk3588 pcie and php
IOMMUs") added the rk3588 SoC's pcie IOMMU and php IOMMU as disabled.
The mmu600_pcie is connected with the five PCIe controllers.
See 8.2 Block Diagram, in rk3588 TRM (Technical Reference Manual).
The five PCIe controllers are:
pcie3x4, pcie3x2, pcie2x1l0, pcie2x1l1, pcie2x1l2.
pcie3x4 can run in either Root Complex mode or Endpoint mode, the other
four PCIe controllers can only run in Root Complex mode. To describe this
we thus have six different device nodes in the device tree.
A PCIe controller in Root Complex mode needs to specify an iommu-map, such
that the device knows how to convert a Requester ID (PCI BDF) to an IOMMU
master ID (stream ID). (A PCIe controller in Endpoint mode should use the
iommus property, just like a regular device.)
If you look at the device tree bindings for msi-map and iommu-map, you can
see that the conversion from Requester ID to MSI-specifier data is the same
as the conversion from Requester ID to IOMMU specifier data. Thus it is
sensible to define the iommu-map property value similar to the msi-map,
such that the conversion will be identical.
Add the proper iommu device tree properties for these six device nodes
connected to the mmu600_pcie, so that we can enable the mmu600_pcie IOMMU.
(The mmu600_php IOMMU is not touched, so it is still disabled.)
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20241107123732.1160063-2-cassel@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c component probing support from Wolfram Sang:
"Add OF component probing.
Some devices are designed and manufactured with some components having
multiple drop-in replacement options. These components are often
connected to the mainboard via ribbon cables, having the same signals
and pin assignments across all options. These may include the display
panel and touchscreen on laptops and tablets, and the trackpad on
laptops. Sometimes which component option is used in a particular
device can be detected by some firmware provided identifier, other
times that information is not available, and the kernel has to try to
probe each device.
Instead of a delicate dance between drivers and device tree quirks,
this change introduces a simple I2C component probe function. For a
given class of devices on the same I2C bus, it will go through all of
them, doing a simple I2C read transfer and see which one of them
responds. It will then enable the device that responds"
* tag 'i2c-for-6.13-rc1-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: fix typo in I2C OF COMPONENT PROBER
of: base: Document prefix argument for of_get_next_child_with_prefix()
i2c: Fix whitespace style issue
arm64: dts: mediatek: mt8173-elm-hana: Mark touchscreens and trackpads as fail
platform/chrome: Introduce device tree hardware prober
i2c: of-prober: Add GPIO support to simple helpers
i2c: of-prober: Add simple helpers for regulator support
i2c: Introduce OF component probe function
of: base: Add for_each_child_of_node_with_prefix()
of: dynamic: Add of_changeset_update_prop_string
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull bprintf() removal from Steven Rostedt:
- Remove unused bprintf() function, that was added with the rest of the
"bin-printf" functions.
These are functions that are used by trace_printk() that allows to
quickly save the format and arguments into the ring buffer without
the expensive processing of converting numbers to ASCII. Then on
output, at a much later time, the ring buffer is read and the string
processing occurs then. The bprintf() was added for consistency but
was never used. It can be safely removed.
* tag 'trace-printf-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
printf: Remove unused 'bprintf'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Borislav Petkov:
- Fix a case where posix timers with a thread-group-wide target would
miss signals if some of the group's threads are exiting
- Fix a hang caused by ndelay() calling the wrong delay function
__udelay()
- Fix a wrong offset calculation in adjtimex(2) when using ADJ_MICRO
(microsecond resolution) and a negative offset
* tag 'timers_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Target group sigqueue to current task only if not exiting
delay: Fix ndelay() spuriously treated as udelay()
ntp: Remove invalid cast in time offset math
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Move the ->select callback to the correct ops structure in
irq-mvebu-sei to fix some Marvell Armada platforms
- Add a workaround for Hisilicon ITS erratum 162100801 which can cause
some virtual interrupts to get lost
- More platform_driver::remove() conversion
* tag 'irq_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Switch back to struct platform_driver::remove()
irqchip/gicv3-its: Add workaround for hip09 ITS erratum 162100801
irqchip/irq-mvebu-sei: Move misplaced select() callback to SEI CP domain
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Add a terminating zero end-element to the array describing AMD CPUs
affected by erratum 1386 so that the matching loop actually
terminates instead of going off into the weeds
- Update the boot protocol documentation to mention the fact that the
preferred address to load the kernel to is considered in the
relocatable kernel case too
- Flush the memory buffer containing the microcode patch after applying
microcode on AMD Zen1 and Zen2, to avoid unnecessary slowdowns
- Make sure the PPIN CPU feature flag is cleared on all CPUs if PPIN
has been disabled
* tag 'x86_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Terminate the erratum_1386_microcode array
x86/Documentation: Update algo in init_size description of boot protocol
x86/microcode/AMD: Flush patch buffer mapping after application
x86/mm: Carve out INVLPG inline asm for use by others
x86/cpu: Fix PPIN initialization
|
|
The point behind strscpy() was to once and for all avoid all the
problems with 'strncpy()' and later broken "fixed" versions like
strlcpy() that just made things worse.
So strscpy not only guarantees NUL-termination (unlike strncpy), it also
doesn't do unnecessary padding at the destination. But at the same time
also avoids byte-at-a-time reads and writes by _allowing_ some extra NUL
writes - within the size, of course - so that the whole copy can be done
with word operations.
It is also stable in the face of a mutable source string: it explicitly
does not read the source buffer multiple times (so an implementation
using "strnlen()+memcpy()" would be wrong), and does not read the source
buffer past the size (like the mis-design that is strlcpy does).
Finally, the return value is designed to be simple and unambiguous: if
the string cannot be copied fully, it returns an actual negative error,
making error handling clearer and simpler (and the caller already knows
the size of the buffer). Otherwise it returns the string length of the
result.
However, there was one final stability issue that can be important to
callers: the stability of the destination buffer.
In particular, the same way we shouldn't read the source buffer more
than once, we should avoid doing multiple writes to the destination
buffer: first writing a potentially non-terminated string, and then
terminating it with NUL at the end does not result in a stable result
buffer.
Yes, it gives the right result in the end, but if the rule for the
destination buffer was that it is _always_ NUL-terminated even when
accessed concurrently with updates, the final byte of the buffer needs
to always _stay_ as a NUL byte.
[ Note that "final byte is NUL" here is literally about the final byte
in the destination array, not the terminating NUL at the end of the
string itself. There is no attempt to try to make concurrent reads and
writes give any kind of consistent string length or contents, but we
do want to guarantee that there is always at least that final
terminating NUL character at the end of the destination array if it
existed before ]
This is relevant in the kernel for the tsk->comm[] array, for example.
Even without locking (for either readers or writers), we want to know
that while the buffer contents may be garbled, it is always a valid C
string and always has a NUL character at 'comm[TASK_COMM_LEN-1]' (and
never has any "out of thin air" data).
So avoid any "copy possibly non-terminated string, and terminate later"
behavior, and write the destination buffer only once.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
bprintf() is unused. Remove it. It was added in the commit 4370aa4aa753
("vsprintf: add binary printf") but as far as I can see was never used,
unlike the other two functions in that patch.
Link: https://lore.kernel.org/20241002173147.210107-1-linux@treblig.org
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Acked-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- assorted minor bug fixes
- assorted platform specific tweaks
- initial RAPL PSYS (SysWatt) support
* tag 'turbostat-2024.11.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: 2024.11.30
tools/power turbostat: Add RAPL psys as a built-in counter
tools/power turbostat: Fix child's argument forwarding
tools/power turbostat: Force --no-perf in --dump mode
tools/power turbostat: Add support for /sys/class/drm/card1
tools/power turbostat: Cache graphics sysfs file descriptors during probe
tools/power turbostat: Consolidate graphics sysfs access
tools/power turbostat: Remove unnecessary fflush() call
tools/power turbostat: Enhance platform divergence description
tools/power turbostat: Add initial support for GraniteRapids-D
tools/power turbostat: Remove PC3 support on Lunarlake
tools/power turbostat: Rename arl_features to lnl_features
tools/power turbostat: Add back PC8 support on Arrowlake
tools/power turbostat: Remove PC7/PC9 support on MTL
tools/power turbostat: Honor --show CPU, even when even when num_cpus=1
tools/power turbostat: Fix trailing '\n' parsing
tools/power turbostat: Allow using cpu device in perf counters on hybrid platforms
tools/power turbostat: Fix column printing for PMT xtal_time counters
tools/power turbostat: fix GCC9 build regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fix from Bjorn Helgaas:
- When removing a PCI device, only look up and remove a platform device
if there is an associated device node for which there could be a
platform device, to fix a merge window regression (Brian Norris)
* tag 'pci-v6.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/pwrctrl: Unregister platform device only if one actually exists
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm
Pull ima fix from Paul Moore:
"One small patch to fix a function parameter / local variable naming
snafu that went up to you in the current merge window"
* tag 'lsm-pr-20241129' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
ima: uncover hidden variable in ima_match_rules()
|
|
Pull more block updates from Jens Axboe:
- NVMe pull request via Keith:
- Use correct srcu list traversal (Breno)
- Scatter-gather support for metadata (Keith)
- Fabrics shutdown race condition fix (Nilay)
- Persistent reservations updates (Guixin)
- Add the required bits for MD atomic write support for raid0/1/10
- Correct return value for unknown opcode in ublk
- Fix deadlock with zone revalidation
- Fix for the io priority request vs bio cleanups
- Use the correct unsigned int type for various limit helpers
- Fix for a race in loop
- Cleanup blk_rq_prep_clone() to prevent uninit-value warning and make
it easier for actual humans to read
- Fix potential UAF when iterating tags
- A few fixes for bfq-iosched UAF issues
- Fix for brd discard not decrementing the allocated page count
- Various little fixes and cleanups
* tag 'block-6.13-20242901' of git://git.kernel.dk/linux: (36 commits)
brd: decrease the number of allocated pages which discarded
block, bfq: fix bfqq uaf in bfq_limit_depth()
block: Don't allow an atomic write be truncated in blkdev_write_iter()
mq-deadline: don't call req_get_ioprio from the I/O completion handler
block: Prevent potential deadlock in blk_revalidate_disk_zones()
block: Remove extra part pointer NULLify in blk_rq_init()
nvme: tuning pr code by using defined structs and macros
nvme: introduce change ptpl and iekey definition
block: return bool from get_disk_ro and bdev_read_only
block: remove a duplicate definition for bdev_read_only
block: return bool from blk_rq_aligned
block: return unsigned int from blk_lim_dma_alignment_and_pad
block: return unsigned int from queue_dma_alignment
block: return unsigned int from bdev_io_opt
block: req->bio is always set in the merge code
block: don't bother checking the data direction for merges
block: blk-mq: fix uninit-value in blk_rq_prep_clone and refactor
Revert "block, bfq: merge bfq_release_process_ref() into bfq_put_cooperator()"
md/raid10: Atomic write support
md/raid1: Atomic write support
...
|
|
Pull more io_uring updates from Jens Axboe:
- Remove a leftover struct from when the cqwait registered waiting was
transitioned to regions.
- Fix for an issue introduced in this merge window, where nop->fd might
be used uninitialized. Ensure it's always set.
- Add capping of the task_work run in local task_work mode, to prevent
bursty and long chains from adding too much latency.
- Work around xa_store() leaving ->head non-NULL if it encounters an
allocation error during storing. Just a debug trigger, and can go
away once xa_store() behaves in a more expected way for this
condition. Not a major thing as it basically requires fault injection
to trigger it.
- Fix a few mapping corner cases
- Fix KCSAN complaint on reading the table size post unlock. Again not
a "real" issue, but it's easy to silence by just keeping the reading
inside the lock that protects it.
* tag 'io_uring-6.13-20242901' of git://git.kernel.dk/linux:
io_uring/tctx: work around xa_store() allocation error issue
io_uring: fix corner case forgetting to vunmap
io_uring: fix task_work cap overshooting
io_uring: check for overflows in io_pin_pages
io_uring/nop: ensure nop->fd is always initialized
io_uring: limit local tw done
io_uring: add io_local_work_pending()
io_uring/region: return negative -E2BIG in io_create_region()
io_uring: protect register tracing
io_uring: remove io_uring_cqwait_reg_arg
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fix from Christoph Hellwig:
- fix physical address calculation for struct dma_debug_entry (Fedor
Pchelkin)
* tag 'dma-mapping-6.13-2024-11-30' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: fix physical address calculation for struct dma_debug_entry
|
|
Pull more kvm updates from Paolo Bonzini:
- ARM fixes
- RISC-V Svade and Svadu (accessed and dirty bit) extension support for
host and guest
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: riscv: selftests: Add Svade and Svadu Extension to get-reg-list test
RISC-V: KVM: Add Svade and Svadu Extensions Support for Guest/VM
dt-bindings: riscv: Add Svade and Svadu Entries
RISC-V: Add Svade and Svadu Extensions Support
KVM: arm64: Use MDCR_EL2.HPME to evaluate overflow of hyp counters
KVM: arm64: Ignore PMCNTENSET_EL0 while checking for overflow status
KVM: arm64: Mark set_sysreg_masks() as inline to avoid build failure
KVM: arm64: vgic-its: Add stronger type-checking to the ITS entry sizes
KVM: arm64: vgic: Kill VGIC_MAX_PRIVATE definition
KVM: arm64: vgic: Make vgic_get_irq() more robust
KVM: arm64: vgic-v3: Sanitise guest writes to GICR_INVLPIR
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Two small fixes.
The first one by Huacai Chen addresses a runtime warning when
CONFIG_CPUMASK_OFFSTACK and CONFIG_DEBUG_PER_CPU_MAPS are selected
which occurs because the cpuinfo code on sh incorrectly uses NR_CPUS
when iterating CPUs instead of the runtime limit nr_cpu_ids.
A second fix by Dan Carpenter fixes a use-after-free bug in
register_intc_controller() which occurred as a result of improper
error handling in the interrupt controller driver code when
registering an interrupt controller during plat_irq_setup() on sh"
* tag 'sh-for-v6.13-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: intc: Fix use-after-free bug in register_intc_controller()
sh: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Deselect ARCH_CORRECT_STACKTRACE_ON_KRETPROBE so that tests depending
on it don't run (and fail) on arm64
- Fix lockdep assert in the Arm SMMUv3 PMU driver
- Fix the port and device ID bits setting in the Arm CMN perf driver
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
perf/arm-cmn: Ensure port and device id bits are set properly
perf/arm-smmuv3: Fix lockdep assert in ->event_init()
arm64: disable ARCH_CORRECT_STACKTRACE_ON_KRETPROBE tests
|
|
since 2024.07.26:
assorted minor bug fixes
assorted platform specific tweaks
initial RAPL PSYS (SysWatt) support
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Introduce the counter as a part of global, platform counters structure.
We open the counter for only one cpu, but otherwise treat it as an
ordinary RAPL counter, allowing for grouped perf read.
The counter is disabled by default, because it's interpretation may
require additional, platform specific information, making it unsuitable
for general use.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add '+' to optstring when early scanning for --no-msr and --no-perf.
It causes option processing to stop as soon as a nonoption argument is
encountered, effectively skipping child's arguments.
Fixes: 3e4048466c39 ("tools/power turbostat: Add --no-msr option")
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Force the --no-perf early to prevent using it as a source. User asks for
raw values, but perf returns them relative to the opening of the file
descriptor.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
On some machines, the graphics device is enumerated as
/sys/class/drm/card1 instead of /sys/class/drm/card0. The current
implementation does not handle this scenario, resulting in the loss of
graphics C6 residency and frequency information.
Add support for /sys/class/drm/card1, ensuring that turbostat can
retrieve and display the graphics columns for these platforms.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Snapshots of the graphics sysfs knobs are taken based on file
descriptors. To optimize this process, open the files and cache the file
descriptors during the graphics probe phase. As a result, the previously
cached pathnames become redundant and are removed.
This change aims to streamline the code without altering its functionality.
No functional change intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Currently, there is an inconsistency in how graphics sysfs knobs are
accessed: graphics residency sysfs knobs are opened and closed for each
read, while graphics frequency sysfs knobs are opened once and remain
open until turbostat exits. This inconsistency is confusing and adds
unnecessary code complexity.
Consolidate the access method by opening the sysfs files once and
reusing the file pointers for subsequent accesses. This approach
simplifies the code and ensures a consistent method for accessing
graphics sysfs knobs.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The graphics sysfs knobs are read-only, making the use of fflush()
before reading them redundant.
Remove the unnecessary fflush() call.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
In various generations, platforms often share a majority of features,
diverging only in a few specific aspects. The current approach of using
hardcoded values in 'platform_features' structure fails to effectively
represent these divergences.
To improve the description of platform divergence:
1. Each newly introduced 'platform_features' structure must have a base,
typically derived from the previous generation.
2. Platform feature values should be inherited from the base structure
rather than being hardcoded.
This approach ensures a more accurate and maintainable representation of
platform-specific features across different generations.
Converts `adl_features` and `lnl_features` to follow this new scheme.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add initial support for GraniteRapids-D. It shares the same features
with SapphireRapids.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Lunarlake supports CC1/CC6/CC7/PC2/PC6/PC10.
Remove PC3 support on Lunarlake.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
As ARL shares the same features with ADL/RPL/MTL, now 'arl_features' is
used by Lunarlake platform only.
Rename 'arl_features' to 'lnl_features'.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Similar to ADL/RPL/MTL, ARL supports CC1/CC6/CC7/PC2/PC3/PC6/PC8/PC10.
Add back PC8 support on Arrowlake.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Similar to ADL/RPL, MTL support CC1/CC6/CC7/PC2/PC3/PC6/PC8/CP10.
Remove PC7/PC9 support on MTL.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
