| Age | Commit message (Collapse) | Author |
|---|
|
PCIe island clock frequency is used when converting coalescing
parameters from usecs to NFP timestamps. Most chips don't run
at 1200MHz, allow FW to provide us with the real frequency.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP is entirely programmable, including the PCI data interface.
Using a fixed control BAR layout certainly makes implementations
easier, but require careful considerations when space is allocated.
Once BAR area is allocated to one feature nothing else can use it.
Allocating space statically also requires it to be sized upfront,
which leads to either unnecessary limitation or wastage.
We currently have a 32bit capability word defined which tells drivers
which application FW features are supported. Most of the bits
are exhausted. The same bits are also reused for enabling specific
features. Bulk of capabilities don't have a need for an enable bit,
however, leading to confusion and wastage.
TLVs seems like a better fit for expressing capabilities of applications
running on programmable hardware.
This patch leaves the front of the BAR as is, and declares a TLV
capability start at offset 0x58. Most of the space up to 0x0d90
is already allocated, but the used space can be wrapped with RESERVED
TLVs. E.g.:
Address Type Length
0x0058 RESERVED 0xe00 /* Wrap basic structures */
0x0e5c FEATURE_A 0x004
0x0e64 FEATURE_B 0x004
0x0e6c RESERVED 0x990 /* Wrap qeueue stats */
0x1800 FEATURE_C 0x100
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When driver app matching loaded FW is not found users are faced with:
nfp: failed to find app with ID 0x%02x
This message does not properly explain that matching driver code is
either not built into the driver or the driver is too old.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Representors are grouped in sets by type. Currently the whole
sets are under RCU protection, but individual representor pointers
are not. This causes some inconveniences when representors have
to be destroyed, because we have to allocate new sets to remove
any representors. Protect the individual pointers with RCU.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The write side of repr tables is always done under pf->lock.
Add a helper to dereference repr table pointers under protection
of that lock.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Devlink used to have two global locks: devlink lock and port lock,
our lock ordering looked like this:
devlink lock -> driver's pf->lock -> devlink port lock
After recent changes port lock was replaced with per-instance
lock. Unfortunately, new per-instance lock is taken on most
operations now. This means we can only grab the pf->lock from
the port split/unsplit ops. Lock ordering looks like this:
devlink lock -> driver's pf->lock -> devlink instance lock
Since we can't take pf->lock from most devlink ops, make sure
nfp_apps are prepared to service them as soon as devlink is
registered. Locking the pf must be pushed down after
nfp_app_init() callback.
The init order looks like this:
nfp_app_init
devlink_register
nfp_app_start
netdev/port_register
As soon as app_init is done nfp_apps must be ready to service
devlink-related callbacks. apps can only register their own
devlink objects from nfp_app_start.
Fixes: 2406e7e546b2 ("devlink: Add per devlink instance lock")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP app is currently shut down as soon as all the vNICs are gone.
This means we can't depend on the app existing throughout the
lifetime of the device. Free the app only from PCI remove path.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the helpers for accessing 4 or 8 byte values over
the CPP bus return the length of IO on success. If the IO
was short caller has to deal with error handling. The short
IO for 4/8B values is completely impractical. Make the
helpers return an error if full access was not possible.
Fix the few places which are actually dealing with errors
correctly, most call sites already only deal with negative
return codes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the packets return true for is_last_ethertype_ip, surround it
with likely compiler hint.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Extend the stats group API to have an update_stats() callback which
will be used to fetch the hardware or software counters data.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Merge the per priority traffic and pfc groups into one group, because
both groups share the same update_stats() callback which will be
introduced in the upcoming patch.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add per-channel counter ch#_eq_rearm to monitor how many lost interrupt
recovery actions happened upon TX timeouts.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
recovery
Up until this patch, on every TX timeout we would try to do channels
recovery. However, in case of a lost interrupt for an EQ, the channel
associated to it cannot be recovered if reopened as it would never get
another interrupt on sent/received traffic, and eventually ends up with
another TX timeout (Restarting the EQ is not part of channel recovery).
This patch adds a mechanism for explicitly polling EQ in case of a TX
timeout in order to recover from a lost interrupt. If this is not the
case (no pending EQEs), perform a channels full recovery as usual.
Once a lost EQE is recovered, it triggers the NAPI to run and handle all
pending completions. This will free some budget in the bql (via calling
netdev_tx_completed_queue) or by clearing pending TXWQEs and waking up
the queue. One of the above actions will move the queue to be ready for
transmit again.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When TX timeout occurs, EQ consumer index and irqn can help in debug for
understanding the SW state of EQ. Add them to the logger prints for the
relevant EQ only.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When driver callback for TX timeout is being called, it handles all
stopped xmit queues (not only the ones which their timeout expired).
Add usecs since last transmit to TX timeout logs per send queue in order
to monitor if the queue timeout expired.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For a given hairpin packet buffer size, different queue sizes
(values of log_hairpin_num_packets) determine how the data is broken
to strides on the RQ. Currently the chosen value is set to 64B strides.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Allow to specify the size of the hairpin queues along with the
packet buffer data size from the core setup code.
If the driver doesn't provide this, the FW applies proper value that
matches the provided data size and a FW chosen RQ stride size.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Support RSS for hairpin traffic. We create multiple hairpin RQ/SQ pairs
and RSS TTC table per hairpin instance and steer the related flows
through that table so they are spread between the pairs.
We open one pair per 50Gbs link speed, for all speeds <= 50Gbs, there
is one pair and no RSS while for 100Gbs ports two RSSed pairs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Enhance the hairpin setup code at the core to support a set of N
(RQ,SQ) pairs. This will be later used by the caller to set RSS
spreading among the different RQs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This will allow to be able and set TC rule whose steering dest is
RSS TTC steering table.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to use RSS for hairpin, we refactor the code that deals with
setup of the TTC steering tables. This is done using an interim ttc
params object that has the flow table attributes, TIR numbers, etc.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
As part of the QoS model, on xmit, the HW mandates that all packets going
through a given SQ have the same priority. To align hairpin SQs with that,
we use the priority given as part of the matching for the hairpin hash key.
This ensures that flows/packets mapped to different HW priorities will
go through different hairpin instances. If no priority is given for
matching, we treat that as an 8th priority, this is in order not to
harm cases where priority is specified.
Only the PCP priority trust model is supported.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The peer vhca id spans less bits vs the ifindex and can
well serve for the hairpin hash key, move to use that.
This is a pre-step to put more info into the hairpin hash
key in downstream patch while keeping it at 32 bits.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Yuchung Cheng says:
====================
tcp: do not use RTT from delayed ACKs for min-RTT
This patch set prevents TCP sender from using RTT samples from
(suspected) delayed ACKs as the minimum RTT, to avoid unbounded
over-estimation of the network path delay. This issue is common
when a connection has extended periods of one packet chit-chat
beyond the min RTT filter window. The first patch does that for TCP
general min RTT estimation. The second patch addresses specifically
the BBR congestion control's min RTT filter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A persistent connection may send tiny amount of data (e.g. health-check)
for a long period of time. BBR's windowed min RTT filter may only see
RTT samples from delayed ACKs causing BBR to grossly over-estimate
the path delay depending how much the ACK was delayed at the receiver.
This patch skips RTT samples that are likely coming from delayed ACKs. Note
that it is possible the sender never obtains a valid measure to set the
min RTT. In this case BBR will continue to set cwnd to initial window
which seems fine because the connection is thin stream.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids having TCP sender or congestion control
overestimate the min RTT by orders of magnitude. This happens when
all the samples in the windowed filter are one-packet transfer
like small request and health-check like chit-chat, which is farily
common for applications using persistent connections. This patch
tries to conservatively labels and skip RTT samples obtained from
this type of workload.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Letting tipc_poll() dereference a socket's pointer to struct tipc_group
entails a race risk, as the group item may be deleted in a concurrent
tipc_sk_join() or tipc_sk_leave() thread.
We now move the 'open' flag in struct tipc_group to struct tipc_sock,
and let the former retain only a pointer to the moved field. This will
eliminate the race risk.
Reported-by: syzbot+799dafde0286795858ac@syzkaller.appspotmail.com
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the switch block in l2tp_nl_cmd_session_create() that
checks pseudowire-specific parameters since just L2TP_PWTYPE_ETH and
L2TP_PWTYPE_PPP are currently supported and no actual checks are
performed. Moreover the L2TP_PWTYPE_IP/default case presents a harmless
issue in error handling (break instead of goto out_tunnel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
on T6, IPv6 filter would occupy 2 tids instead of 4.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lorenzo Bianconi says:
====================
l2tp: set l2specific_len based on l2specific_type
Do not rely on l2specific_len value provided by userspace but set sublayer
length according to l2specific_type.
Mark L2TP_ATTR_L2SPEC_LEN attribute as not used
Changes since v2:
- drop the patch related to a fix in the switch default case in
l2tp_nl_cmd_session_create()
- use L2SPECTYPE_NONE as default case in l2tp_get_l2specific_len()
Changes since v1:
- remove l2specific_len parameter
- add sanity check on l2specific_type provided by userspace
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove l2specific_len configuration parameter since now L2-Specific
Sublayer length is computed according to l2specific_type provided by
userspace.
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove l2specific_len dependency while building l2tpv3 header or
parsing the received frame since default L2-Specific Sublayer is
always four bytes long and we don't need to rely on a user supplied
value.
Moreover in l2tp netlink code there are no sanity checks to
enforce the relation between l2specific_len and l2specific_type,
so sending a malformed netlink message is possible to set
l2specific_type to L2TP_L2SPECTYPE_DEFAULT (or even
L2TP_L2SPECTYPE_NONE) and set l2specific_len to a value greater than
4 leaking memory on the wire and sending corrupted frames.
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add sanity check on l2specific_type provided by userspace in
l2tp_nl_cmd_session_create() since just L2TP_L2SPECTYPE_DEFAULT and
L2TP_L2SPECTYPE_NONE are currently supported.
Moreover explicitly set l2specific_type to L2TP_L2SPECTYPE_DEFAULT
only if the userspace does not provide a value for it
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rahul Lakkireddy says:
====================
cxgb4: reduce memory footprint for collecting firmware dump
Firmware dump can be large (upto 2 GB). In low memory conditions,
ethtool fails to allocate such large memory. So, use zlib deflate
to compress collected firmware dump.
Patch 1 updates collection logic to use compression.
Patch 2 adds zlib deflate to compress collected firmware dump.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use zlib deflate to compress firmware dump. Collect and compress
as much firmware dump as possible into a 32 MB buffer.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update firmware dump collection logic to use compression when available.
Let collection logic attempt to do compression, instead of returning out
of memory early.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Helmut reported a bug about devision by zero while
running traffic and doing physical cable pull test.
When the cable unplugged the ppms become zero, so when
dividing the current ppms by the previous ppms in the
next dim iteration there is devision by zero.
This patch prevent this division for both ppms and epms.
Fixes: c3164d2fc48f ("net/mlx5e: Added BW check for DIM decision mechanism")
Fixes: 4c4dbb4a7363 ("net/mlx5e: Move dynamic interrupt coalescing code to include/linux")
Reported-by: Helmut Grauer <helmut.grauer@de.ibm.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Two more small fixes
- The conversion of enums into their actual numbers to display in the
event format file had an off-by-one bug, that could cause an enum
not to be converted, and break user space parsing tools.
- A fix to a previous fix to bring back the context recursion checks.
The interrupt case checks for NMI, IRQ and softirq, but the softirq
returned the same number regardless if it was set or not, although
the logic would force it to be set if it were hit"
* tag 'trace-v4.15-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix converting enum's from the map in trace_event_eval_update()
ring-buffer: Fix duplicate results in mapping context to bits in recursive lock
|
|
Fixes the following sparse warnings:
net/core/devlink.c:2297:25: warning:
symbol 'devlink_resource_find' was not declared. Should it be static?
net/core/devlink.c:2322:6: warning:
symbol 'devlink_resource_validate_children' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- a fix for use-after-free in Synaptics RMI4 driver
- correction to multitouch contact tracking on certain ALPS touchpads
(which got broken when we tried to fix the 2-finger scrolling)
- touchpad on Lenovo T640p is switched over to SMbus/RMI
- a few device node refcount fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - prevent UAF reported by KASAN
Input: ALPS - fix multi-touch decoding on SS4 plus touchpads
Input: synaptics - Lenovo Thinkpad T460p devices should use RMI
Input: of_touchscreen - add MODULE_LICENSE
Input: 88pm860x-ts - fix child-node lookup
Input: twl6040-vibra - fix child-node lookup
Input: twl4030-vibra - fix sibling-node lookup
|
|
Fixes the following sparse warning:
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:289:5: warning:
symbol 'mlxsw_sp_kvdl_part_occ' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable miistat is not used. So it is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two bugfixes for the I2C core: Lixing Wang fixed a refcounting problem
with DT nodes. Jeremy Compostella fixed a buffer overflow possibility
when using a 'don't use' ioctl interface directly"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core-smbus: prevent stack corruption on read I2C_BLOCK_DATA
i2c: core: decrease reference count of device node in i2c_unregister_device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixlet from Tejun Heo:
"This just adds one more entry for liteon optical drives to the device
blacklist for large IOs.
The change is very low risk"
* 'for-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: apply MAX_SEC_1024 to all LITEON EP1 series devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"cgroup.threads should be delegatable (ie. a container should be able
to write to it from inside) but was missing the flag.
The change is very low risk"
* 'for-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: make cgroup.threads delegatable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixlet from Tejun Heo:
"One patch to add touch_nmi_watchdog() while dumping workqueue debug
messages to avoid triggering the lockup detector spuriously.
The change is very low risk"
* 'for-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: avoid hard lockups in show_workqueue_state()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"We have various small DT fixes, and one important regression fix:
The recent device tree bugfixes that were intended to address issues
that 'dtc' started warning about in 4.15 fixed various USB PHY device
nodes, but it turns out that we had code that depended on those nodes
being incorrect and the probe failing with a particular error code.
With the workaround we can also deal with correct device nodes.
The DT fixes include:
- Allwinner A10 and A20 had the display pipeline set up incorrectly
(introduced in v4.15)
- The Altera PMU lacked an interrupt-parent (never worked)
- Pin muxing on the Openblocks A7 (never worked)
- Clocks might get set up wrong on Armada 7K/8K (4.15 regression)
We now have additional device tree patches to address all the
remaining warnings introduced in 4.15, but decided to queue them for
4.16 instead, to avoid risking another regression like the USB PHY
thing mentioned above.
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
phy: work around 'phys' references to usb-nop-xceiv devices
ARM: sunxi_defconfig: Enable CMA
arm64: dts: socfpga: add missing interrupt-parent
ARM: dts: sun[47]i: Fix display backend 1 output to TCON0 remote endpoint
ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
ARM: dts: da850-lcdk: Remove leading 0x and 0s from unit address
ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"More than we'd like after rc8, but nothing very alarming either, just
tying up loose ends before the release:
Since we changed powernv to use cpufreq_get() from show_cpuinfo(), we
see warnings with PREEMPT enabled. But the preempt_disable() in
show_cpuinfo() doesn't actually prevent CPU hotplug as it suggests, so
remove it.
Two updates to the recently merged RFI flush code. Wire up the generic
sysfs file to report the status, and add a debugfs file to allow
enabling/disabling it at runtime.
Two updates to xmon, one to add the RFI flush related fields to the
paca dump, and another to not use hashed pointers in the paca dump.
And one minor fix to add a missing include of linux/types.h in
asm/hvcall.h, not seen to break the build in upstream, but correct
anyway.
Thanks to: Benjamin Herrenschmidt, Michal Suchanek, Nicholas Piggin"
* tag 'powerpc-4.15-8' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: include linux/types.h in asm/hvcall.h
powerpc/64s: Allow control of RFI flush via debugfs
powerpc/64s: Wire up cpu_show_meltdown()
powerpc: Don't preempt_disable() in show_cpuinfo()
powerpc/xmon: Don't print hashed pointers in paca dump
powerpc/xmon: Add RFI flush related fields to paca dump
|
|
Since commit 41033f029e39 ("snmp: Remove duplicate OUTMCAST stat
increment") one line of code became unneeded.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
