| Age | Commit message (Collapse) | Author |
|---|
|
Before attempting to activate a RAID array, it is checked for sufficient
redundancy. That is, we make sure that there are not too many failed
devices - or devices specified for rebuild - to undermine our ability to
activate the array. The current code performs this check twice - once to
ensure there were not too many devices specified for rebuild by the user
('validate_rebuild_devices') and again after possibly experiencing a failure
to read the superblock ('analyse_superblocks'). Neither of these checks are
sufficient. The first check is done properly but with insufficient
information about the possible failure state of the devices to make a good
determination if the array can be activated. The second check is simply
done wrong in the case of RAID10 because it doesn't account for the
independence of the stripes (i.e. mirror sets). The solution is to use the
properly written check ('validate_rebuild_devices'), but perform the check
after the superblocks have been read and we know which devices have failed.
This gives us one check instead of two and performs it in a location where
it can be done right.
Only RAID10 was affected and it was affected in the following ways:
- the code did not properly catch the condition where a user specified
a device for rebuild that already had a failed device in the same mirror
set. (This condition would, however, be caught at a deeper level in MD.)
- the code triggers a false positive and denies activation when devices in
independent mirror sets have failed - counting the failures as though they
were all in the same set.
The most likely place this error was introduced (or this patch should have
been included) is in commit 4ec1e369 - first introduced in v3.7-rc1.
Consequently this fix should also go in v3.7.y, however there is a
small conflict on the .version in raid_target, so I'll submit a
separate patch to -stable.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
"The asm-generic changeset has been ack'ed by Arnd."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up finit_module
asm-generic/dma-mapping-broken.h: Provide dma_alloc_attrs()/dma_free_attrs()
m68k: Provide dma_alloc_attrs()/dma_free_attrs()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- ELF coredump fix (more registers dumped than what user space expects)
- SUBARCH name generation (s/aarch64/arm64/)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: makefile: fix uname munging when setting ARCH on native machine
arm64: elf: fix core dumping to match what glibc expects
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
This patch (as1643b) fixes a build error in ehci-hcd when compiling for
ARM with allmodconfig:
drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition
drivers/usb/host/ehci-mxc.c:280:31: warning: 'ehci_mxc_driver' defined but not used [-Wunused-variable]
drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition
The fix is to convert ehci-mxc over to the new "ehci-hcd is a library"
scheme so that it can coexist peacefully with the ehci-platform
driver. As part of the conversion the ehci_mxc_priv data structure,
which was allocated dynamically, is now placed where it belongs: in
the private area at the end of struct ehci_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This was introduced in commit 6dccd16 "r8169: merge with version
6.001.00 of Realtek's r8169 driver". I did not find the version
6.001.00 online, but in 6.002.00 or any later r8169 from Realtek
this hunk is no longer present.
Also commit 05af214 "r8169: fix Ethernet Hangup for RTL8110SC
rev d" claims to have fixed this issue otherwise.
The magic compare mask of 0xfffe000 is dubious as it masks
parts of the Reserved part, and parts of the VLAN tag. But this
does not make much sense as the VLAN tag parts are perfectly
valid there. In matter of fact this seems to be triggered with
any VLAN tagged packet as RxVlanTag bit is matched. I would
suspect 0xfffe0000 was intended to test reserved part only.
Finally, this hunk is evil as it can cause more packets to be
handled than what was NAPI quota causing net/core/dev.c:
net_rx_action(): WARN_ON_ONCE(work > weight) to trigger, and
mess up the NAPI state causing device to hang.
As result, any system using VLANs and having high receive
traffic (so that NAPI poll budget limits rtl_rx) would result
in device hang.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We create new flow caches when a new flow is identified by tuntap, This may lead
some issues:
- userspace may produce a huge amount of short live flows to exhaust host memory
- the unlimited number of flow caches may produce a long list which increase the
time in the linear searching
Solve this by introducing a limit of total number of flow caches.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A MAX_TAP_QUEUES(1024) queues of tuntap device is always allocated
unconditionally even userspace only requires a single queue device. This is
unnecessary and will lead a very high order of page allocation when has a high
possibility to fail. Solving this by creating a one queue net device when
userspace only use one queue and also reduce MAX_TAP_QUEUES to
DEFAULT_MAX_NUM_RSS_QUEUES which can guarantee the success of
the allocation.
Reported-by: Dirk Hohndel <dirk@hohndel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reverting 328d7b8 and instead adding an exception for the
Sierra Wireless MC7710.
commit 328d7b8 (net: cdc_mbim: send ZLP after max sized NTBs)
added a workaround for an issue observed on one specific device.
Concerns were raised that this workaround adds a performance
penalty to all devices based on questionable, if not buggy,
behaviour of a single device:
"If you add ZLP for NTBs of dwNtbOutMaxSize, you are heavily affecting CPU
load, increasing interrupt load by factor of 2 in high load traffic
scenario and possibly decreasing throughput for all other devices
which behaves correctly."
"The idea of NCM was to avoid extra ZLPs. If your transfer is exactly
dwNtbOutMaxSize, it's known, you can submit such request on the receiver
side and you do not need any EOT indicatation, so the frametime can be
used for useful data."
Adding a device specific exception to prevent the workaround from
affecting well behaved devices.
The assumption here is that needing a ZLP is truly an *exception*.
We do not yet have enough data to verify this. The generic
workaround in commit 328d7b8 should be considered acceptable despite
the performance penalty if the exception list becomes a maintainance
hassle.
Cc: Alexey ORISHKO <alexey.orishko@stericsson.com>
Cc: Yauheni Kaliuta <y.kaliuta@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Only a few small HD-audio fixes:
- Addition of new Conexant codec IDs
- Two one-liners to add fixups for Realtek codecs
- A last-minute regression fix for auto-mute with power-saving mode
(regressed since 3.8-rc1)"
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix inconsistent pin states after resume
ALSA: hda - Add Conexant CX20755/20756/20757 codec IDs
ALSA: hda - Add fixup for Acer AO725 laptop
ALSA: hda - Fix mute led for another HP machine
|
|
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The commit [26a6cb6c: ALSA: hda - Implement a poll loop for jacks as a
module parameter] introduced the polling jack detection code, but it
also moved the call of snd_hda_jack_set_dirty_all() in the resume path
after resume/init ops call. This caused a regression when the jack
state has been changed during power-down (e.g. in the power save
mode). Since the driver doesn't probe the new jack state but keeps
using the cached value due to no dirty flag, the pin state remains
also as if the jack is still plugged.
The fix is simply moving snd_hda_jack_set_dirty_all() to the original
position.
Reported-by: Manolo Díaz <diaz.manolo@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Concerning pinctrl_macb0_rmii_mii, values were okay, but not comments.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Reported-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
No need for this cmdline option as we are using DT.
Moreover this defconfig is targeted to multiple SoC/boards: this option
was nonsense.
Reported-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This patch overrides default macb pinctrl config defined in
at91sam9260.dtsi (pinctrl_macb_rmii) with kizbox board config
(pinctrl_macb_rmii + pinctrl_macb_rmii_mii_alt).
Signed-off-by: Boris BREZILLON <linux-arm@overkiz.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Make BGA as the default version as we are supposed to just have
to specify when we use the PQFP version.
Issue was existing since commit:
3e90772 (ARM: at91: fix at91rm9200 soc subtype handling).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org> [v3.3]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The SCK pins where missing in usarts pinctrl.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The PIN_BANK 3 is for PDxx pins, not PCxx pins.
And PIN_BANK 1 is for PBxx, not PIN_BANK 0.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The relation between PIN_BANK numbers and pio letters wasn't made very
clear.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
When it goes to error through line 144, the memory allocated to *devname is
not freed, and the caller doesn't free it either in line 250. So we free the
memroy of *devname in function cifs_compose_mount_options() when it goes to
error.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
CC: stable <stable@kernel.org>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
This reverts commit eccf2979b2c034b516e01b8a104c3739f7ef07d1.
The reason is that it broke TI WiLink shared transport on Panda.
Also, callback functions should not be added to board files anymore,
so revert to implementing the power functions in the driver itself.
Additionally, changed a variable name ('status' to 'err') so that this
revert compiles properly.
Cc: stable <stable@vger.kernel.org> [3.7]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The gpio controller on kirkwood can provide interrupts but is missing
the #interrupt-cells property. This patch just adds it to both gpio
controllers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
There are a number of bugs in the error paths of this driver. Make
use of devm_ functions to simplify the cleanup on error.
Based on a patch by Russell King.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
the variable cpuclk and clk_name should be properly freed when error happens.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"The most important is a fix for a pciehp deadlock that occurs when
unplugging a Thunderbolt adapter. We also applied the same fix to
shpchp, removed CONFIG_EXPERIMENTAL dependencies, fixed a
pcie_aspm=force problem, and fixed a refcount leak.
Details:
- Hotplug
PCI: pciehp: Use per-slot workqueues to avoid deadlock
PCI: shpchp: Make shpchp_wq non-ordered
PCI: shpchp: Handle push button event asynchronously
PCI: shpchp: Use per-slot workqueues to avoid deadlock
- Power management
PCI: Allow pcie_aspm=force even when FADT indicates it is unsupported
- Misc
PCI/AER: pci_get_domain_bus_and_slot() call missing required pci_dev_put()
PCI: remove depends on CONFIG_EXPERIMENTAL"
* tag '3.8-pci-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: remove depends on CONFIG_EXPERIMENTAL
PCI: Allow pcie_aspm=force even when FADT indicates it is unsupported
PCI: shpchp: Use per-slot workqueues to avoid deadlock
PCI: shpchp: Handle push button event asynchronously
PCI: shpchp: Make shpchp_wq non-ordered
PCI/AER: pci_get_domain_bus_and_slot() call missing required pci_dev_put()
PCI: pciehp: Use per-slot workqueues to avoid deadlock
|
|
Commit 083b804c4d3e ("async: use workqueue for worker pool") made it
possible that async jobs are moved from pending to running out-of-order.
While pending async jobs will be queued and dispatched for execution in
the same order, nothing guarantees they'll enter "1) move self to the
running queue" of async_run_entry_fn() in the same order.
Before the conversion, async implemented its own worker pool. An async
worker, upon being woken up, fetches the first item from the pending
list, which kept the executing lists sorted. The conversion to
workqueue was done by adding work_struct to each async_entry and async
just schedules the work item. The queueing and dispatching of such work
items are still in order but now each worker thread is associated with a
specific async_entry and moves that specific async_entry to the
executing list. So, depending on which worker reaches that point
earlier, which is non-deterministic, we may end up moving an async_entry
with larger cookie before one with smaller one.
This broke __lowest_in_progress(). running->domain may not be properly
sorted and is not guaranteed to contain lower cookies than pending list
when not empty. Fix it by ensuring sort-inserting to the running list
and always looking at both pending and running when trying to determine
the lowest cookie.
Over time, the async synchronization implementation became quite messy.
We better restructure it such that each async_entry is linked to two
lists - one global and one per domain - and not move it when execution
starts. There's no reason to distinguish pending and running. They
behave the same for synchronization purposes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
. revert 20b279 - require exclude_guest to use PEBS - kernel side, now
older binaries will continue working for things like cycles:pp
without needing to pass extra modifiers, from David Ahern.
. Fix building from 'make perf-*-src-pkg' tarballs, broken by UAPI,
from Sebastian Andrzej Siewior
[ Pulling directly, Ingo would normally pull but has been unresponsive ]
* tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf tools: Fix building from 'make perf-*-src-pkg' tarballs
perf x86: revert 20b279 - require exclude_guest to use PEBS - kernel side
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Improve the stability of the linux kernel on the parisc architecture"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: sigaltstack doesn't round ss.ss_sp as required
parisc: improve ptrace support for gdb single-step
parisc: don't claim cpu irqs more than once
parisc: avoid undefined shift in cnv_float.h
|
|
The acpi core will call request_module("acpi-cpufreq") on subsystem init,
but this will fail if the module isn't available at that stage of boot.
Add some module aliases to ensure that udev can load the module on Intel
and AMD systems with the appropriate feature bits - I /think/ that this
will also work on VIA systems, but haven't verified that.
References: http://lkml.kernel.org/r/1448223.sdUJnNSRz4@vostro.rjw.lan
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Tested-by: Leonid Isaev <lisaev@umail.iu.edu>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"This contain a bugfix for CUSE and miscellaneous small fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: remove unused variable in fuse_try_move_page()
fuse: make fuse_file_fallocate() static
fuse: Move CUSE Kconfig entry from fs/Kconfig into fs/fuse/Kconfig
cuse: fix uninitialized variable warnings
cuse: do not register multiple devices with identical names
cuse: use mutex as registration lock instead of spinlocks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here are some GPIO fixes I stacked up in my GPIO tree:
- Remove a bad #include from the Samsung driver
- Some Kconfig hazzle for the Samsungs
- Skip gpiolib registration on EXYNOS5440
- Don't free the MVEBU label"
* tag 'fixes-for-v3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mvebu: Don't free chip label memory
gpio: samsung: skip gpio lib registration for EXYNOS5440
gpio: samsung: silent build warning for EXYNOS5 SoCs
gpio: samsung: fix pinctrl condition for exynos and exynos5440
gpio: samsung: remove inclusion <mach/regs-clock.h>
|
|
Add missing "!" as we are supposed to check "!card->adapter"
in PCIe suspend handler.
Cc: "3.2+" <stable@vger.kernel.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Sergey V. <sftp.mtuci@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Chain swapping should only be enabled when the EEPROM chainmask is set to 5,
regardless of what the runtime chainmask is.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The kbuild test robot reports the following warning with x86_64-randconfig-x955:
warning: (RTL8192CE && RTL8192SE && RTL8192DE && RTL8723AE && RTL8192CU) selects
RTLWIFI which has unmet direct dependencies (NETDEVICES && WLAN &&
(RTL8192CE || RTL8192CU || RTL8192SE || RTL8192DE))
This warning was introduced in commit a290593, "rtlwifi: Modify files for addition
of rtl8723ae", and is d ue to a missing dependence of RTLWIFI on RTL8723AE.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: kbuild test robot <fengguang.wu@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We do not correctly change interface type when switching from
IBSS mode to STA mode, that results in microcode errors.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=886946
Reported-by: Jaroslav Skarvada <jskarvad@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git commit 9cb3a50c (ipv4: Invalidate the socket cached route on
pmtu events if possible) introduced a refcount problem. We don't
get a refcount on the route if we get it from__sk_dst_get(), but
we need one if we want to reuse this route because __sk_dst_set()
releases the refcount of the old route. This patch adds proper
refcount handling for that case. We introduce a 'new' flag to
indicate that we are going to use a new route and we release the
old route only if we replace it by a new one.
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Minimal omap fixes for the -rc series:
- A build fix for recently merged omap DRM changes
- Regression fixes from the common clock framework conversion
for omap4 audio and omap2 reboot
- Regression fix for pandaboard WLAN control UART muxing caused by
u-boot only muxing essential pins nowadays
- Timer iteration fix for CONFIG_OF_DYNAMIC
- A section mismatch fix for ocp2scp init
* tag 'omap-for-v3.8-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (306 commits)
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
ARM: OMAP4: hwmod_data: Correct IDLEMODE for McPDM
ARM: OMAP4: clock data: Lock ABE DPLL on all revisions
+ Linux 3.8-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
1) The transport header did not point to the right place after
esp/ah processing on tunnel mode in the receive path. As a
result, the ECN field of the inner header was not set correctly,
fixes from Li RongQing.
2) We did a null check too late in one of the xfrm_replay advance
functions. This can lead to a division by zero, fix from
Nickolai Zeldovich.
3) The size calculation of the hash table missed the muiltplication
with the actual struct size when the hash table is freed.
We might call the wrong free function, fix from Michal Kubecek.
4) On IPsec pmtu events we can't access the transport headers of
the original packet, so force a relookup for all routes
to notify about the pmtu event.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 6a328d8c6f03501657ad580f6f98bf9a42583ff7 changed the update
logic for the socket but it does not update the SCM_RIGHTS update
as well. This patch is based on the net_prio fix commit
48a87cc26c13b68f6cce4e9d769fcb17a6b3e4b8
net: netprio: fd passed in SCM_RIGHTS datagram not set correctly
A socket fd passed in a SCM_RIGHTS datagram was not getting
updated with the new tasks cgrp prioidx. This leaves IO on
the socket tagged with the old tasks priority.
To fix this add a check in the scm recvmsg path to update the
sock cgrp prioidx with the new tasks value.
Let's apply the same fix for net_cls.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Reported-by: Li Zefan <lizefan@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: netdev@vger.kernel.org
Cc: cgroups@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Christoph Paasch found netxen could trigger a BUG in its dismantle
phase, in netxen_release_tx_buffer(), using full size TSO packets.
cmd_buf->frag_count includes the skb->data part, so the loop must
start at index 1 instead of 0, or else we can make an out
of bound access to cmd_buff->frag_array[MAX_SKB_FRAGS + 2]
Christoph provided the fixes in netxen_map_tx_skb() function.
In case of a dma mapping error, its better to clear the dma fields
so that we don't try to unmap them again in netxen_release_tx_buffer()
Reported-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs fixes from Jaegeuk Kim:
o Support swap file and link generic_file_remap_pages
o Enhance the bio streaming flow and free section control
o Major bug fix on recovery routine
o Minor bug/warning fixes and code cleanups
* tag 'f2fs-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (22 commits)
f2fs: use _safe() version of list_for_each
f2fs: add comments of start_bidx_of_node
f2fs: avoid issuing small bios due to several dirty node pages
f2fs: support swapfile
f2fs: add remap_pages as generic_file_remap_pages
f2fs: add __init to functions in init_f2fs_fs
f2fs: fix the debugfs entry creation path
f2fs: add global mutex_lock to protect f2fs_stat_list
f2fs: remove the blk_plug usage in f2fs_write_data_pages
f2fs: avoid redundant time update for parent directory in f2fs_delete_entry
f2fs: remove redundant call to set_blocksize in f2fs_fill_super
f2fs: move f2fs_balance_fs to punch_hole
f2fs: add f2fs_balance_fs in several interfaces
f2fs: revisit the f2fs_gc flow
f2fs: check return value during recovery
f2fs: avoid null dereference in f2fs_acl_from_disk
f2fs: initialize newly allocated dnode structure
f2fs: update f2fs partition info about SIT/NAT layout
f2fs: update f2fs document to reflect SIT/NAT layout correctly
f2fs: remove unneeded INIT_LIST_HEAD at few places
...
|
|
Pull vfio fix from Alex Williamson.
"vfio-pci: Fix buffer overfill"
* tag 'vfio-for-v3.8-rc5' of git://github.com/awilliam/linux-vfio:
vfio-pci: Fix buffer overfill
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"Kprobes now uses the function tracer if it can. That is, if a probe
is placed on a function mcount/nop location, and the arch supports it,
instead of adding a breakpoint, kprobes will register a function
callback as that is much more efficient.
The function tracer requires to update modules before they run, and
uses the module notifier to do so. But if something else in the
module notifiers registers a kprobe at one of these locations, before
ftrace can get to it, then the system could fail.
The function tracer must be initialized early, otherwise module
notifiers that probe will only work by chance."
* tag 'trace-3.8-rc4-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Be first to run code modification on modules
|
