| Age | Commit message (Collapse) | Author |
|---|
|
The new xarray lookup code requires to know complete kcontrol->id before
snd_ctl_add() call. Reorder the code to make the initialization properly.
Cc: stable@kernel.org # v5.19+
Reported-by: Martin Zidek <zidek@master.cz>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230606073122.597491-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When receiving a connect response we should make sure that the DCID is
within the valid range and that we don't already have another channel
allocated for the same DCID.
Missing checks may violate the specification (BLUETOOTH CORE SPECIFICATION
Version 5.4 | Vol 3, Part A, Page 1046).
Fixes: 40624183c202 ("Bluetooth: L2CAP: Add missing checks for invalid LE DCID")
Signed-off-by: Sungwoo Kim <iam@sung-woo.kim>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The order of CIS handle array in Set CIG Parameters response shall match
the order of the CIS_ID array in the command (Core v5.3 Vol 4 Part E Sec
7.8.97). We send CIS_IDs mainly in the order of increasing CIS_ID (but
with "last" CIS first if it has fixed CIG_ID). In handling of the
reply, we currently assume this is also the same as the order of
hci_conn in hdev->conn_hash, but that is not true.
Match the correct hci_conn to the correct handle by matching them based
on the CIG+CIS combination. The CIG+CIS combination shall be unique for
ISO_LINK hci_conn at state >= BT_BOUND, which we maintain in
hci_le_set_cig_params.
Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Consider existing BOUND & CONNECT state CIS to block CIG removal.
Otherwise, under suitable timing conditions we may attempt to remove CIG
while Create CIS is pending, which fails.
Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
L2CAP assumes that the locks conn->chan_lock and chan->lock are
acquired in the order conn->chan_lock, chan->lock to avoid
potential deadlock.
For example, l2sock_shutdown acquires these locks in the order:
mutex_lock(&conn->chan_lock)
l2cap_chan_lock(chan)
However, l2cap_disconnect_req acquires chan->lock in
l2cap_get_chan_by_scid first and then acquires conn->chan_lock
before calling l2cap_chan_del. This means that these locks are
acquired in unexpected order, which leads to potential deadlock:
l2cap_chan_lock(c)
mutex_lock(&conn->chan_lock)
This patch releases chan->lock before acquiring the conn_chan_lock
to avoid the potential deadlock.
Fixes: a2a9339e1c9d ("Bluetooth: L2CAP: Fix use-after-free in l2cap_disconnect_{req,rsp}")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Since commit 3e4be65eb82c ("Bluetooth: hci_qca: Add poweroff support
during hci down for wcn3990"), the setup callback which registers the
debugfs interface can be called multiple times.
This specifically leads to the following error when powering on the
controller:
debugfs: Directory 'ibs' with parent 'hci0' already present!
Add a driver flag to avoid trying to register the debugfs interface more
than once.
Fixes: 3e4be65eb82c ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990")
Cc: stable@vger.kernel.org # 4.20
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Since commit ec6cef9cd98d ("Bluetooth: Fix SMP channel registration for
unconfigured controllers") the debugfs interface for unconfigured
controllers will be created when the controller is configured.
There is however currently nothing preventing a controller from being
configured multiple time (e.g. setting the device address using btmgmt)
which results in failed attempts to register the already registered
debugfs entries:
debugfs: File 'features' in directory 'hci0' already present!
debugfs: File 'manufacturer' in directory 'hci0' already present!
debugfs: File 'hci_version' in directory 'hci0' already present!
...
debugfs: File 'quirk_simultaneous_discovery' in directory 'hci0' already present!
Add a controller flag to avoid trying to register the debugfs interface
more than once.
Fixes: ec6cef9cd98d ("Bluetooth: Fix SMP channel registration for unconfigured controllers")
Cc: stable@vger.kernel.org # 4.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When the HCI_UNREGISTER flag is set, no jobs should be scheduled. Fix
potential race when HCI_UNREGISTER is set after the flag is tested in
hci_cmd_sync_queue.
Fixes: 0b94f2651f56 ("Bluetooth: hci_sync: Fix queuing commands when HCI_UNREGISTER is set")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Similar to commit 0f7d9b31ce7a ("netfilter: nf_tables: fix use-after-free
in nft_set_catchall_destroy()"). We can not access k after kfree_rcu()
call.
Cc: stable@vger.kernel.org
Signed-off-by: Min Li <lm0963hack@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Make CIG auto-allocation to select the first CIG_ID that is still
configurable. Also use correct CIG_ID range (see Core v5.3 Vol 4 Part E
Sec 7.8.97 p.2553).
Previously, it would always select CIG_ID 0 regardless of anything,
because cis_list with data.cis == 0xff (BT_ISO_QOS_CIS_UNSET) would not
count any CIS. Since we are not adding CIS here, use find_cis instead.
Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When looking for CIS blocking CIG removal, consider only the CIS with
the right CIG ID. Don't try to remove CIG with unset CIG ID.
Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The existing documentation refers to memory.high as the "main mechanism
to control memory usage." This seems incorrect to me - memory.high can
result in reclaim pressure which simply leads to stalls unless some
external component observes and actions on it (e.g. systemd-oomd can be
used for this purpose). While this is feasible, users are unaware of
this interaction and are led to believe that memory.high alone is an
effective mechanism for limiting memory.
The documentation should recommend the use of memory.max as the
effective way to enforce memory limits - it triggers reclaim and results
in OOM kills by itself.
Signed-off-by: Dan Schatzberg <schatzberg.dan@gmail.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Chris Down <chris@chrisdown.name>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Memory/pages are not freed, when unloading nullblk driver.
Steps to reproduce issue
1.free -h
total used free shared buff/cache available
Mem: 7.8Gi 260Mi 7.1Gi 3.0Mi 395Mi 7.3Gi
Swap: 0B 0B 0B
2.modprobe null_blk memory_backed=1
3.dd if=/dev/urandom of=/dev/nullb0 oflag=direct bs=1M count=1000
4.modprobe -r null_blk
5.free -h
total used free shared buff/cache available
Mem: 7.8Gi 1.2Gi 6.1Gi 3.0Mi 398Mi 6.3Gi
Swap: 0B 0B 0B
Signed-off-by: Anuj Gupta <anuj20.g@samsung.com>
Signed-off-by: Nitesh Shetty <nj.shetty@samsung.com>
Link: https://lore.kernel.org/r/20230605062354.24785-1-nj.shetty@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Andrii Nakryiko writes:
And we currently don't have an attach type for NETLINK BPF link.
Thankfully it's not too late to add it. I see that link_create() in
kernel/bpf/syscall.c just bypasses attach_type check. We shouldn't
have done that. Instead we need to add BPF_NETLINK attach type to enum
bpf_attach_type. And wire all that properly throughout the kernel and
libbpf itself.
This adds BPF_NETFILTER and uses it. This breaks uabi but this
wasn't in any non-rc release yet, so it should be fine.
v2: check link_attack prog type in link_create too
Fixes: 84601d6ee68a ("bpf: add bpf_link support for BPF_NETFILTER programs")
Suggested-by: Andrii Nakryiko <andrii.nakryiko@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/CAEf4BzZ69YgrQW7DHCJUT_X+GqMq_ZQQPBwopaJJVGFD5=d5Vg@mail.gmail.com/
Link: https://lore.kernel.org/bpf/20230605131445.32016-1-fw@strlen.de
|
|
It seems we forgot the normal case to terminate the retry loop,
making us asking 3 times each command, which is probably a little bit
too much.
And remove the ugly "goto exit" that can be replaced by a simpler "break"
Fixes: 586e8fede795 ("HID: logitech-hidpp: Retry commands when device is busy")
Suggested-by: Mark Lord <mlord@pobox.com>
Tested-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Fixes headset detection on Clevo NS50AU.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230605163834.24653-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for Asus ROG 2024 models using CS35L41 SPI with Internal
Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230605153308.448550-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Several device tree files get the polarity of the pendown-gpios
wrong: this signal is active low. Fix up all incorrect flags, so
that operating systems can rely on the flag being correctly set.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230510105156.1134320-1-linus.walleij@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes
AT91 fixes for 6.4
It contains:
- fix imbalanced reference counter for ethernet devices; without it
system hangs after consecutive suspend/resume cycles;
- fix debounce delay property for shutdown controller; the initial DT
property is not what the driver expects.
* tag 'at91-fixes-6.4' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc
ARM: at91: pm: fix imbalanced reference counter for ethernet devices
Link: https://lore.kernel.org/r/20230530105930.11621-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM64 DeviceTree fixes for 6.4
Register scheme for SM8550 LLCC is corrected to avoid using the wrong
register offsets. SDRAM frequency for misidentified SC7180-lite boards
is handled. The datatype for Soundwire interval on SM8550 is corrected.
The resource controller on SC8280XP is added to the CPU cluster
power-domain to get notified to send cached sleep and wake votes before
going entering the lower power states.
SA8155P power-domains that differ from what's inherited from the SM8150
DeviceTree are adjusted to make the platform boot again.
Remoteproc firmware paths are corrected for Sony Xperia 10 IV.
Cache properties are adjusted across a range of platforms, to meet
changes in the binding.
Panel compatibles are corrected for Xiaomi Mi Pad 5 Pro, to match
binding. Invalid dai-cells are dropped from SC7280 devices, to match
binding.
The incorrect removal of "input-enable" from the LPASS pinctrl node of
SC8280XP was reverted, to get dmic pins in the correct state again.
The incorrect input-enable property is dropped from a msm8974, mdm9615
and apq8026 to resolve a range of DT validation warnings, incorrectly
picked up through the ARM64 tree.
* tag 'qcom-arm64-fixes-for-6.4' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sm8550: Use the correct LLCC register scheme
arm64: dts: qcom: sc7180-lite: Fix SDRAM freq for misidentified sc7180-lite boards
arm64: dts: qcom: sm8550: use uint16 for Soundwire interval
arm64: dts: qcom: Split out SA8155P and use correct RPMh power domains
arm64: dts: qcom: sm6375-pdx225: Fix remoteproc firmware paths
arm64: dts: qcom: add missing cache properties
arm64: dts: qcom: use decimal for cache level
arm64: dts: qcom: fix indentation
ARM: dts: qcom: msm8974: remove superfluous "input-enable"
ARM: dts: qcom: mdm9615: remove superfluous "input-enable"
ARM: dts: qcom: apq8026: remove superfluous "input-enable"
arm64: dts: qcom: sm8250-xiaomi-elish-csot: fix panel compatible
arm64: dts: qcom: sm8250-xiaomi-elish-boe: fix panel compatible
arm64: dts: qcom: sc7280-qcard: drop incorrect dai-cells from WCD938x SDW
arm64: dts: qcom: sc7280-idp: drop incorrect dai-cells from WCD938x SDW
arm64: dts: qcom: sc8280xp: Flush RSC sleep & wake votes
arm64: dts: qcom: sc8280xp: Revert "arm64: dts: qcom: sc8280xp: remove superfluous "input-enable""
Link: https://lore.kernel.org/r/20230601142659.2246348-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm driver fixes for 6.4
Error paths is corrected across icc-bwmon, rpmh-rsc, ramp_controller and
rmtfs. The ice module is renamed qcom_ice, to avoid clashing with
existing "ice" driver.
SA8155P-specific RPMh power-domains are introduced to avoid the code
trying to access resources that exists on SM8150, but not on SA8155P.
Lastly, changes to the EDAC driver to fix an issue where the driver
performs mmio based on the wrong register map.
* tag 'qcom-driver-fixes-for-6.4' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
EDAC/qcom: Get rid of hardcoded register offsets
EDAC/qcom: Remove superfluous return variable assignment in qcom_llcc_core_setup()
dt-bindings: cache: qcom,llcc: Fix SM8550 description
soc: qcom: rpmhpd: Add SA8155P power domains
dt-bindings: power: qcom,rpmpd: Add SA8155P
soc: qcom: Rename ice to qcom_ice to avoid module name conflict
soc: qcom: rmtfs: Fix error code in probe()
soc: qcom: ramp_controller: Fix an error handling path in qcom_ramp_controller_probe()
soc: qcom: rpmh-rsc: drop redundant unsigned >=0 comparision
soc: qcom: icc-bwmon: fix incorrect error code passed to dev_err_probe()
Link: https://lore.kernel.org/r/20230601141058.2246039-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM32 fix for 6.4
A range of 32-bit Qualcomm platforms are missing cache-unified, which is
now required by the binding, this is now corrected.
* tag 'qcom-dts-fixes-for-6.4' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: add missing cache properties
Link: https://lore.kernel.org/r/20230601140347.2245680-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/robertosassu/linux
Pull asymmetric keys fix from Roberto Sassu:
"Here is a small fix to make an unconditional copy of the buffer passed
to crypto operations, to take into account the case of the stack not
in the linear mapping area.
It has been tested and verified to fix the bug"
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: David Howells <dhowells@redhat.com>
* tag 'asym-keys-fix-for-linus-v6.4-rc5' of https://github.com/robertosassu/linux:
KEYS: asymmetric: Copy sig and digest in public_key_verify_signature()
|
|
Mat Martineau says:
====================
mptcp: Fixes for address advertisement
Patches 1 and 2 allow address advertisements to be removed without
affecting current connected subflows, and updates associated self tests.
Patches 3 and 4 correctly track (and allow removal of) addresses that
were implicitly announced as part of subflow creation. Also updates
associated self tests.
Patch 5 makes subflow and address announcement counters work consistently
between the userspace and in-kernel path managers.
====================
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increase pm subflows counter on both server side and client side when
userspace pm creates a new subflow, and decrease the counter when it
closes a subflow.
Increase add_addr_signaled counter in mptcp_nl_cmd_announce() when the
address is announced by userspace PM.
This modification is similar to how the in-kernel PM is updating the
counter: when additional subflows are created/removed.
Fixes: 9ab4807c84a4 ("mptcp: netlink: Add MPTCP_PM_CMD_ANNOUNCE")
Fixes: 702c2f646d42 ("mptcp: netlink: allow userspace-driven subflow establishment")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/329
Cc: stable@vger.kernel.org
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To align with what is done by the in-kernel PM, update userspace pm
subflow selftests, by sending the a remove_addrs command together
before the remove_subflows command. This will get a RM_ADDR in
chk_rm_nr().
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE")
Fixes: 5e986ec46874 ("selftests: mptcp: userspace pm subflow tests")
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/379
Cc: stable@vger.kernel.org
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the address into userspace_pm_local_addr_list when the subflow is
created. Make sure it can be found in mptcp_nl_cmd_remove(). And delete
it in the new helper mptcp_userspace_pm_delete_local_addr().
By doing this, the "REMOVE" command also works with subflows that have
been created via the "SUB_CREATE" command instead of restricting to
the addresses that have been announced via the "ANNOUNCE" command.
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE")
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/379
Cc: stable@vger.kernel.org
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is linked to the previous commit ("mptcp: only send RM_ADDR in
nl_cmd_remove").
To align with what is done by the in-kernel PM, update userspace pm addr
selftests, by sending a remove_subflows command together after the
remove_addrs command.
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE")
Fixes: 97040cf9806e ("selftests: mptcp: userspace pm address tests")
Cc: stable@vger.kernel.org
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The specifications from [1] about the "REMOVE" command say:
Announce that an address has been lost to the peer
It was then only supposed to send a RM_ADDR and not trying to delete
associated subflows.
A new helper mptcp_pm_remove_addrs() is then introduced to do just
that, compared to mptcp_pm_remove_addrs_and_subflows() also removing
subflows.
To delete a subflow, the userspace daemon can use the "SUB_DESTROY"
command, see mptcp_nl_cmd_sf_destroy().
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE")
Link: https://github.com/multipath-tcp/mptcp/blob/mptcp_v0.96/include/uapi/linux/mptcp.h [1]
Cc: stable@vger.kernel.org
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW default for wake sync pulses is 18. 10 precharge and 8 preamble. There
is no reason to change this especially as it is causing problems with
certain eDP panels.
v3: Change "Fixes:" commit
v2: Remove "fast wake" repeat from subject
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Fixes: e1c71f8f9180 ("drm/i915: Fix fast wake AUX sync len")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8475
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230530101649.2549949-1-jouni.hogander@intel.com
(cherry picked from commit b29a20f7c4995a059ed764ce42389857426397c7)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
According to Bspec, the voltage level for 480MHz is to be set as 1
instead of 2.
BSpec: 49208
Fixes: 06f1b06dc5b7 ("drm/i915/display: Add 480 MHz CDCLK steps for RPL-U")
v2: rebase
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230529060747.3972259-1-chaitanya.kumar.borah@intel.com
(cherry picked from commit 5a3c46b809d09f8ef59e2fbf2463b1c102aecbaa)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
kernel_context() returns an error pointer. Use pointer-error
conversion functions to evaluate its return value, rather than
checking for a '0' return.
Fixes: eb5c10cbbc2f ("drm/i915: Remove I915_USER_PRIORITY_SHIFT")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v5.13+
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Acked-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526124138.2006110-1-andi.shyti@linux.intel.com
(cherry picked from commit edad9ee94f17adc75d3b13ab51bbe3d615ce1e7e)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
We must not assign plat_dat->dwmac4_addrs unconditionally as for
structures which don't set them, this will result in the core driver
using zeroes everywhere and breaking the driver for older HW. On EMAC < 2
the address should remain NULL.
Fixes: b68376191c69 ("net: stmmac: dwmac-qcom-ethqos: Add EMAC3 support")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There seems to be a bug within the mv64xxx I2C controller, wherein the
status register may not necessarily contain valid value immediately
after the IFLG flag is set in the control register.
My theory is that the controller:
- first sets the IFLG in control register
- then updates the status register
- then raises an interrupt
This may sometime cause weird bugs when in atomic mode, since in this
mode we do not wait for an interrupt, but instead we poll the control
register for IFLG and read status register immediately after.
I encountered -ENXIO from mv64xxx_i2c_fsm() due to this issue when using
this driver in atomic mode.
Note that I've only seen this issue on Armada 385, I don't know whether
other SOCs with this controller are also affected. Also note that this
fix has been in U-Boot for over 4 years [1] without anybody complaining,
so it should not cause regressions.
[1] https://source.denx.de/u-boot/u-boot/-/commit/d50e29662f78
Fixes: 544a8d75f3d6 ("i2c: mv64xxx: Add atomic_xfer method to driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
this is a pull request of 3 patches for net/master.
All 3 patches target the j1939 stack.
The 1st patch is by Oleksij Rempel and fixes the error queue handling
for (E)TP sessions that run into timeouts.
The last 2 patches are by Fedor Pchelkin and fix a potential
use-after-free in j1939_netdev_start() if j1939_can_rx_register()
fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With IC_INTR_RX_FULL slave interrupt handler reads data in a loop until
RX FIFO is empty. When testing with the slave-eeprom, each transaction
has 2 bytes for address/index and 1 byte for value, the address byte
can be written as data byte due to dropping STOP condition.
In the test below, the master continuously writes to the slave, first 2
bytes are index, 3rd byte is value and follow by a STOP condition.
i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D1-D1]
i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D2-D2]
i2c_write: i2c-3 #0 a=04b f=0000 l=3 [00-D3-D3]
Upon receiving STOP condition slave eeprom would reset `idx_write_cnt` so
next 2 bytes can be treated as buffer index for upcoming transaction.
Supposedly the slave eeprom buffer would be written as
EEPROM[0x00D1] = 0xD1
EEPROM[0x00D2] = 0xD2
EEPROM[0x00D3] = 0xD3
When CPU load is high the slave irq handler may not read fast enough,
the interrupt status can be seen as 0x204 with both DW_IC_INTR_STOP_DET
(0x200) and DW_IC_INTR_RX_FULL (0x4) bits. The slave device may see
the transactions below.
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1794 : INTR_STAT=0x204
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x1790 : INTR_STAT=0x200
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x1594 : INTR_STAT=0x4
After `D1` is received, read loop continues to read `00` which is the
first bype of next index. Since STOP condition is ignored by the loop,
eeprom buffer index increased to `D2` and `00` is written as value.
So the slave eeprom buffer becomes
EEPROM[0x00D1] = 0xD1
EEPROM[0x00D2] = 0x00
EEPROM[0x00D3] = 0xD3
The fix is to use `FIRST_DATA_BYTE` (bit 11) in `IC_DATA_CMD` to split
the transactions. The first index byte in this case would have bit 11
set. Check this indication to inject I2C_SLAVE_WRITE_REQUESTED event
which will reset `idx_write_cnt` in slave eeprom.
Signed-off-by: David Zheng <david.zheng@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
We got multiple syzbot reports, all duplicates of the following [1]
syzbot managed to install fq_pie with a zero TCA_FQ_PIE_QUANTUM,
thus triggering infinite loops.
Use limits similar to sch_fq, with commits
3725a269815b ("pkt_sched: fq: avoid hang when quantum 0") and
d9e15a273306 ("pkt_sched: fq: do not accept silly TCA_FQ_QUANTUM")
[1]
watchdog: BUG: soft lockup - CPU#0 stuck for 26s! [swapper/0:0]
Modules linked in:
irq event stamp: 172817
hardirqs last enabled at (172816): [<ffff80001242fde4>] __el1_irq arch/arm64/kernel/entry-common.c:476 [inline]
hardirqs last enabled at (172816): [<ffff80001242fde4>] el1_interrupt+0x58/0x68 arch/arm64/kernel/entry-common.c:486
hardirqs last disabled at (172817): [<ffff80001242fdb0>] __el1_irq arch/arm64/kernel/entry-common.c:468 [inline]
hardirqs last disabled at (172817): [<ffff80001242fdb0>] el1_interrupt+0x24/0x68 arch/arm64/kernel/entry-common.c:486
softirqs last enabled at (167634): [<ffff800008020c1c>] softirq_handle_end kernel/softirq.c:414 [inline]
softirqs last enabled at (167634): [<ffff800008020c1c>] __do_softirq+0xac0/0xd54 kernel/softirq.c:600
softirqs last disabled at (167701): [<ffff80000802a660>] ____do_softirq+0x14/0x20 arch/arm64/kernel/irq.c:80
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.4.0-rc3-syzkaller-geb0f1697d729 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/28/2023
pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : fq_pie_qdisc_dequeue+0x10c/0x8ac net/sched/sch_fq_pie.c:246
lr : fq_pie_qdisc_dequeue+0xe4/0x8ac net/sched/sch_fq_pie.c:240
sp : ffff800008007210
x29: ffff800008007280 x28: ffff0000c86f7890 x27: ffff0000cb20c2e8
x26: ffff0000cb20c2f0 x25: dfff800000000000 x24: ffff0000cb20c2e0
x23: ffff0000c86f7880 x22: 0000000000000040 x21: 1fffe000190def10
x20: ffff0000cb20c2e0 x19: ffff0000cb20c2e0 x18: ffff800008006e60
x17: 0000000000000000 x16: ffff80000850af6c x15: 0000000000000302
x14: 0000000000000100 x13: 0000000000000000 x12: 0000000000000001
x11: 0000000000000302 x10: 0000000000000100 x9 : 0000000000000000
x8 : 0000000000000000 x7 : ffff80000841c468 x6 : 0000000000000000
x5 : 0000000000000001 x4 : 0000000000000001 x3 : 0000000000000000
x2 : ffff0000cb20c2e0 x1 : ffff0000cb20c2e0 x0 : 0000000000000001
Call trace:
fq_pie_qdisc_dequeue+0x10c/0x8ac net/sched/sch_fq_pie.c:246
dequeue_skb net/sched/sch_generic.c:292 [inline]
qdisc_restart net/sched/sch_generic.c:397 [inline]
__qdisc_run+0x1fc/0x231c net/sched/sch_generic.c:415
__dev_xmit_skb net/core/dev.c:3868 [inline]
__dev_queue_xmit+0xc80/0x3318 net/core/dev.c:4210
dev_queue_xmit include/linux/netdevice.h:3085 [inline]
neigh_connected_output+0x2f8/0x38c net/core/neighbour.c:1581
neigh_output include/net/neighbour.h:544 [inline]
ip6_finish_output2+0xd60/0x1a1c net/ipv6/ip6_output.c:134
__ip6_finish_output net/ipv6/ip6_output.c:195 [inline]
ip6_finish_output+0x538/0x8c8 net/ipv6/ip6_output.c:206
NF_HOOK_COND include/linux/netfilter.h:292 [inline]
ip6_output+0x270/0x594 net/ipv6/ip6_output.c:227
dst_output include/net/dst.h:458 [inline]
NF_HOOK include/linux/netfilter.h:303 [inline]
ndisc_send_skb+0xc30/0x1790 net/ipv6/ndisc.c:508
ndisc_send_rs+0x47c/0x5d4 net/ipv6/ndisc.c:718
addrconf_rs_timer+0x300/0x58c net/ipv6/addrconf.c:3936
call_timer_fn+0x19c/0x8cc kernel/time/timer.c:1700
expire_timers kernel/time/timer.c:1751 [inline]
__run_timers+0x55c/0x734 kernel/time/timer.c:2022
run_timer_softirq+0x7c/0x114 kernel/time/timer.c:2035
__do_softirq+0x2d0/0xd54 kernel/softirq.c:571
____do_softirq+0x14/0x20 arch/arm64/kernel/irq.c:80
call_on_irq_stack+0x24/0x4c arch/arm64/kernel/entry.S:882
do_softirq_own_stack+0x20/0x2c arch/arm64/kernel/irq.c:85
invoke_softirq kernel/softirq.c:452 [inline]
__irq_exit_rcu+0x28c/0x534 kernel/softirq.c:650
irq_exit_rcu+0x14/0x84 kernel/softirq.c:662
__el1_irq arch/arm64/kernel/entry-common.c:472 [inline]
el1_interrupt+0x38/0x68 arch/arm64/kernel/entry-common.c:486
el1h_64_irq_handler+0x18/0x24 arch/arm64/kernel/entry-common.c:491
el1h_64_irq+0x64/0x68 arch/arm64/kernel/entry.S:587
__daif_local_irq_enable arch/arm64/include/asm/irqflags.h:33 [inline]
arch_local_irq_enable+0x8/0xc arch/arm64/include/asm/irqflags.h:55
cpuidle_idle_call kernel/sched/idle.c:170 [inline]
do_idle+0x1f0/0x4e8 kernel/sched/idle.c:282
cpu_startup_entry+0x24/0x28 kernel/sched/idle.c:379
rest_init+0x2dc/0x2f4 init/main.c:735
start_kernel+0x0/0x55c init/main.c:834
start_kernel+0x3f0/0x55c init/main.c:1088
__primary_switched+0xb8/0xc0 arch/arm64/kernel/head.S:523
Fixes: ec97ecf1ebe4 ("net: sched: add Flow Queue PIE packet scheduler")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than casting pci1xxxx_i2c_shutdown to an incompatible function type,
update the type to match that expected by __devm_add_action.
Reported by clang-16 with W-1:
.../i2c-mchp-pci1xxxx.c:1159:29: error: cast from 'void (*)(struct pci1xxxx_i2c *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
ret = devm_add_action(dev, (void (*)(void *))pci1xxxx_i2c_shutdown, i2c);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/device.h:251:29: note: expanded from macro 'devm_add_action'
__devm_add_action(release, action, data, #action)
^~~~~~
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Tharun Kumar P<tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
There is a spelling mistake in a comment. Fix it.
Signed-off-by: Christian Heusel <christian@heusel.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
I will help Wolfram out with the i2c controllers patches.
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add "Intel Reference boad" and "Intel NUC 13" SSID in the alc256.
Enable jack headset volume buttons
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Sayed, Karimuddin <karimuddin.sayed@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230602193812.66768-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Headset microphone on this platform does not work without
ALC897_FIXUP_HEADSET_MIC_PIN fixup.
Signed-off-by: RenHai <kean0048@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230602003604.975892-1-kean0048@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a quirk for HP Slim Desktop S01 to fixup headset MIC no presence.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230526094704.14597-1-aichao@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
GCC 11.3.0 issues warnings in this module about wrong sizes of format
specifiers:
pcm-test.c: In function ‘test_pcm_time’:
pcm-test.c:384:68: warning: format ‘%ld’ expects argument of type ‘long int’, but argument 5 \
has type ‘unsigned int’ [-Wformat=]
384 | snprintf(msg, sizeof(msg), "rate mismatch %ld != %ld", rate, rrate);
pcm-test.c:455:53: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has \
type ‘long int’ [-Wformat=]
455 | "expected %d, wrote %li", rate, frames);
pcm-test.c:462:53: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has \
type ‘long int’ [-Wformat=]
462 | "expected %d, wrote %li", rate, frames);
pcm-test.c:467:53: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has \
type ‘long int’ [-Wformat=]
467 | "expected %d, wrote %li", rate, frames);
Simple fix according to compiler's suggestion removed the warnings.
Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230524191528.13203-1-mirsad.todorovac@alu.unizg.hr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
j1939_can_rx_register fails"
Fedor Pchelkin <pchelkin@ispras.ru> says:
The patch series fixes a possible racy use-after-free scenario
described in 2/2: if j1939_can_rx_register() fails then the concurrent
thread may have already read the invalid priv structure.
The 1/2 makes j1939_netdev_lock a mutex so that access to
j1939_can_rx_register() can be serialized without changing GFP_KERNEL
to GFP_ATOMIC inside can_rx_register(). This seems to be safe.
Note that the patch series has been tested only via Syzkaller and not
with a real device.
Link: https://lore.kernel.org/r/20230526171910.227615-1-pchelkin@ispras.ru
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Syzkaller reports the following failure:
BUG: KASAN: use-after-free in kref_put include/linux/kref.h:64 [inline]
BUG: KASAN: use-after-free in j1939_priv_put+0x25/0xa0 net/can/j1939/main.c:172
Write of size 4 at addr ffff888141c15058 by task swapper/3/0
CPU: 3 PID: 0 Comm: swapper/3 Not tainted 5.10.144-syzkaller #0
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x107/0x167 lib/dump_stack.c:118
print_address_description.constprop.0+0x1c/0x220 mm/kasan/report.c:385
__kasan_report mm/kasan/report.c:545 [inline]
kasan_report.cold+0x1f/0x37 mm/kasan/report.c:562
check_memory_region_inline mm/kasan/generic.c:186 [inline]
check_memory_region+0x145/0x190 mm/kasan/generic.c:192
instrument_atomic_read_write include/linux/instrumented.h:101 [inline]
atomic_fetch_sub_release include/asm-generic/atomic-instrumented.h:220 [inline]
__refcount_sub_and_test include/linux/refcount.h:272 [inline]
__refcount_dec_and_test include/linux/refcount.h:315 [inline]
refcount_dec_and_test include/linux/refcount.h:333 [inline]
kref_put include/linux/kref.h:64 [inline]
j1939_priv_put+0x25/0xa0 net/can/j1939/main.c:172
j1939_sk_sock_destruct+0x44/0x90 net/can/j1939/socket.c:374
__sk_destruct+0x4e/0x820 net/core/sock.c:1784
rcu_do_batch kernel/rcu/tree.c:2485 [inline]
rcu_core+0xb35/0x1a30 kernel/rcu/tree.c:2726
__do_softirq+0x289/0x9a3 kernel/softirq.c:298
asm_call_irq_on_stack+0x12/0x20
</IRQ>
__run_on_irqstack arch/x86/include/asm/irq_stack.h:26 [inline]
run_on_irqstack_cond arch/x86/include/asm/irq_stack.h:77 [inline]
do_softirq_own_stack+0xaa/0xe0 arch/x86/kernel/irq_64.c:77
invoke_softirq kernel/softirq.c:393 [inline]
__irq_exit_rcu kernel/softirq.c:423 [inline]
irq_exit_rcu+0x136/0x200 kernel/softirq.c:435
sysvec_apic_timer_interrupt+0x4d/0x100 arch/x86/kernel/apic/apic.c:1095
asm_sysvec_apic_timer_interrupt+0x12/0x20 arch/x86/include/asm/idtentry.h:635
Allocated by task 1141:
kasan_save_stack+0x1b/0x40 mm/kasan/common.c:48
kasan_set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc.constprop.0+0xc9/0xd0 mm/kasan/common.c:461
kmalloc include/linux/slab.h:552 [inline]
kzalloc include/linux/slab.h:664 [inline]
j1939_priv_create net/can/j1939/main.c:131 [inline]
j1939_netdev_start+0x111/0x860 net/can/j1939/main.c:268
j1939_sk_bind+0x8ea/0xd30 net/can/j1939/socket.c:485
__sys_bind+0x1f2/0x260 net/socket.c:1645
__do_sys_bind net/socket.c:1656 [inline]
__se_sys_bind net/socket.c:1654 [inline]
__x64_sys_bind+0x6f/0xb0 net/socket.c:1654
do_syscall_64+0x33/0x40 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x61/0xc6
Freed by task 1141:
kasan_save_stack+0x1b/0x40 mm/kasan/common.c:48
kasan_set_track+0x1c/0x30 mm/kasan/common.c:56
kasan_set_free_info+0x1b/0x30 mm/kasan/generic.c:355
__kasan_slab_free+0x112/0x170 mm/kasan/common.c:422
slab_free_hook mm/slub.c:1542 [inline]
slab_free_freelist_hook+0xad/0x190 mm/slub.c:1576
slab_free mm/slub.c:3149 [inline]
kfree+0xd9/0x3b0 mm/slub.c:4125
j1939_netdev_start+0x5ee/0x860 net/can/j1939/main.c:300
j1939_sk_bind+0x8ea/0xd30 net/can/j1939/socket.c:485
__sys_bind+0x1f2/0x260 net/socket.c:1645
__do_sys_bind net/socket.c:1656 [inline]
__se_sys_bind net/socket.c:1654 [inline]
__x64_sys_bind+0x6f/0xb0 net/socket.c:1654
do_syscall_64+0x33/0x40 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x61/0xc6
It can be caused by this scenario:
CPU0 CPU1
j1939_sk_bind(socket0, ndev0, ...)
j1939_netdev_start()
j1939_sk_bind(socket1, ndev0, ...)
j1939_netdev_start()
mutex_lock(&j1939_netdev_lock)
j1939_priv_set(ndev0, priv)
mutex_unlock(&j1939_netdev_lock)
if (priv_new)
kref_get(&priv_new->rx_kref)
return priv_new;
/* inside j1939_sk_bind() */
jsk->priv = priv
j1939_can_rx_register(priv) // fails
j1939_priv_set(ndev, NULL)
kfree(priv)
j1939_sk_sock_destruct()
j1939_priv_put() // <- uaf
To avoid this, call j1939_can_rx_register() under j1939_netdev_lock so
that a concurrent thread cannot process j1939_priv before
j1939_can_rx_register() returns.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20230526171910.227615-3-pchelkin@ispras.ru
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
It turns out access to j1939_can_rx_register() needs to be serialized,
otherwise j1939_priv can be corrupted when parallel threads call
j1939_netdev_start() and j1939_can_rx_register() fails. This issue is
thoroughly covered in other commit which serializes access to
j1939_can_rx_register().
Change j1939_netdev_lock type to mutex so that we do not need to remove
GFP_KERNEL from can_rx_register().
j1939_netdev_lock seems to be used in normal contexts where mutex usage
is not prohibited.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Suggested-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20230526171910.227615-2-pchelkin@ispras.ru
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
J1939 Socket
This patch addresses an issue within the j1939_sk_send_loop_abort()
function in the j1939/socket.c file, specifically in the context of
Transport Protocol (TP) sessions.
Without this patch, when a TP session is initiated and a Clear To Send
(CTS) frame is received from the remote side requesting one data packet,
the kernel dispatches the first Data Transport (DT) frame and then waits
for the next CTS. If the remote side doesn't respond with another CTS,
the kernel aborts due to a timeout. This leads to the user-space
receiving an EPOLLERR on the socket, and the socket becomes active.
However, when trying to read the error queue from the socket with
sock.recvmsg(, , socket.MSG_ERRQUEUE), it returns -EAGAIN,
given that the socket is non-blocking. This situation results in an
infinite loop: the user-space repeatedly calls epoll(), epoll() returns
the socket file descriptor with EPOLLERR, but the socket then blocks on
the recv() of ERRQUEUE.
This patch introduces an additional check for the J1939_SOCK_ERRQUEUE
flag within the j1939_sk_send_loop_abort() function. If the flag is set,
it indicates that the application has subscribed to receive error queue
messages. In such cases, the kernel can communicate the current transfer
state via the error queue. This allows for the function to return early,
preventing the unnecessary setting of the socket into an error state,
and breaking the infinite loop. It is crucial to note that a socket
error is only needed if the application isn't using the error queue, as,
without it, the application wouldn't be aware of transfer issues.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Reported-by: David Jander <david@protonic.nl>
Tested-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20230526081946.715190-1-o.rempel@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Unlinked list recovery requires errors removing the inode the from
the unlinked list get fed back to the main recovery loop. Now that
we offload the unlinking to the inodegc work, we don't get errors
being fed back when we trip over a corruption that prevents the
inode from being removed from the unlinked list.
This means we never clear the corrupt unlinked list bucket,
resulting in runtime operations eventually tripping over it and
shutting down.
Fix this by collecting inodegc worker errors and feed them
back to the flush caller. This is largely best effort - the only
context that really cares is log recovery, and it only flushes a
single inode at a time so we don't need complex synchronised
handling. Essentially the inodegc workers will capture the first
error that occurs and the next flush will gather them and clear
them. The flush itself will only report the first gathered error.
In the cases where callers can return errors, propagate the
collected inodegc flush error up the error handling chain.
In the case of inode unlinked list recovery, there are several
superfluous calls to flush queued unlinked inodes -
xlog_recover_iunlink_bucket() guarantees that it has flushed the
inodegc and collected errors before it returns. Hence nothing in the
calling path needs to run a flush, even when an error is returned.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
Bad things happen in defered extent freeing operations if it is
passed a bad block number in the xefi. This can come from a bogus
agno/agbno pair from deferred agfl freeing, or just a bad fsbno
being passed to __xfs_free_extent_later(). Either way, it's very
difficult to diagnose where a null perag oops in EFI creation
is coming from when the operation that queued the xefi has already
been completed and there's no longer any trace of it around....
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
