| Age | Commit message (Collapse) | Author |
|---|
|
The event config is controlled through the IIO events subsystem and
device wakeup is controlled by /sys/devices/.../power/wakeup. Let's keep
those two knobs independent.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-10-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The palmas gpadc block has support for monitoring up to 2 ADC channels
and issue an interrupt if they reach past a set threshold. This change
hooks into the IIO events system and exposes to userspace the ability to
configure these threshold values for each channel, but only allow up to
2 such thresholds to be enabled at any given time. Trying to enable a
third channel will result in an error.
Userspace is expected to input calibrated, as opposed to raw, values as
threshold. However, it is not enough to do the opposite of what is done
when converting the other way around. To account for tolerances in the
ADC, the calculated raw threshold should be adjusted based on the ADC
specifications for the device. These specifications include the integral
nonlinearity (INL), offset, and gain error. To adjust the high
threshold, use the following equation:
(calibrated value + INL) * Gain error + offset = maximum value [1]
Likewise, use the following equation for the low threshold:
(calibrated value - INL) * Gain error - offset = minimum value
The gain error is a combination of gain error, as listed in the
datasheet, and gain error drift due to temperature and supply. The exact
values for these specifications vary between palmas devices. This patch
sets the values found in TWL6035, TWL6037 datasheet.
[1] TI Application Report, SLIA087A, Guide to Using the GPADC in
TPS65903x, TPS65917-Q1, TPS65919-Q1, and TPS65916 Devices.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-9-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This prevents leaving the adc in freerunning mode when removing the
driver.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-8-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
It just makes more sense to have all information regarding adc events in
one place.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-7-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Instead of having high_threshold > 0 as an indicator for upper threshold
event and lower threshold event otherwise, use enum iio_event_direction
instead. This is hopefully less ambiguous.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-6-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The palmas gpadc block has support for monitoring up to 2 ADC channels
and issue an interrupt if they reach past a set threshold. This is
currently used to wake up the system from sleep, but the functionality
is more generic than that. As such, change the naming of functions and
variables to refer to it as events instead, except during suspend and
resume where wakeup still make sense.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-5-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
It does not seem to be used by anyone and later patches in this series
are made simpler by first removing this. There is now a lot of dead code
that cannot be reached, until later patches revive it. Arguably, this is
preferred over removing the code only to add it again.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230408114825.824505-4-risca@dalakolonin.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Review of a recent fix highlighted that this driver could be trivially
converted to be entirely devm managed.
That fix should be applied to resolve the fix in a fashion easy to back port
even though this change removes the relevant code.
[1] https://patchwork.kernel.org/project/linux-iio/patch/20230313205029.1881745-1-risca@dalakolonin.se/
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Patrik Dahlström <risca@dalakolonin.se>
Reviewed-by: Patrik Dahlström <risca@dalakolonin.se>
Link: https://lore.kernel.org/r/20230318163039.56115-1-jic23@kernel.org
|
|
DSDT ROTM method seen in the wild with SMO8B30 _HID.
Making assumption it is similar to that used for bmc150 plus
information from Darrell that the rotation is out by 90 degrees at boot.
Method (ROTM, 0, NotSerialized)
{
Name (RBUF, Package (0x03)
{
"0 -1 0",
"1 0 0",
"0 0 1"
})
Return (RBUF) /* \_SB_.PCI0.I2C5.DEV_.ROTM.RBUF */
}
Reported-by: Darrell Kavanagh <darrell.kavanagh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Darrell Kavanagh <darrell.kavanagh@gmail.org>
Link: https://lore.kernel.org/r/20230130201018.981024-3-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
ID seen in the wild and it is a valid ST micro ID.
An offset of 1 for the device ID enum is needed when adding support for
retrieving the ID from device_get_match_data() to allow detection of
NULL pointer and fallback to i2c_device_id table.
DSDT chunk cropped for relevant parts.
Scope (_SB.PCI0.I2C5)
{
Device (DEV)
{
Name (_HID, EisaId ("SMO8B30")) // _HID: Hardware ID
Name (_CID, EisaId ("SMO8B30")) // _CID: Compatible ID
Name (_UID, Zero) // _UID: Unique ID
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x006A, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C5",
0x00, ResourceConsumer, , Exclusive,
)
})
Return (RBUF) /* \_SB_.PCI0.I2C5.DEV_._CRS.RBUF */
}
Method (ROTM, 0, NotSerialized)
{
Name (RBUF, Package (0x03)
{
"0 -1 0",
"1 0 0",
"0 0 1"
})
Return (RBUF) /* \_SB_.PCI0.I2C5.DEV_.ROTM.RBUF */
}
...
Link: https://lore.kernel.org/all/20230129182441.082f29d0@jic23-huawei/
Reported-by: Darrell Kavanagh <darrell.kavanagh@gmail.com>
Tested-by: Darrell Kavanagh <darrell.kavanagh@gmail.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230130201018.981024-2-jic23@kernel.org
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanups for the 6.4 cycle.
New device support
* bosch,bmp280
- Add support for BMP580 - includes significant refactoring and general
driver cleanup + support for non-volatile memory for trimming and config
parameters.
* rohm BU27034
- New driver for this 3 channel ambient light sensor.
- New support library for devices where both integration time and
amplifier gain are configurable. In these cases a scale change
may require changing bother underlying values. This library module
provides code to help with this.
* st,accel
- Add support for IIS328DQ (ID only as compatible wtih LIS331DL)
* st,lsm6dsx
- Add support for ASM330LHB automotive MEMS sensor.
* ti,ads1100, ads1000
- New driver for these 16 bit ADCs.
* ti,tmp117
- Add support for older tmp116 device. Includes some general driver cleanup.
Staging driver drops
* adi,ade7854
- Driver was a very long way from compliant with IIO infrastructure and ABI.
If anyone wants a non staging version of this driver they are better off
starting from scratch. Hence drop it and the associated meter.h header.
Features
* adi,ad7441r
- Add DT binding to set sink current for digital input.
* semtech,sx9324,9360
- Support older register mapping from firmware designed for windows.
Core improvements.
* Move iio_trigger_poll() docs to next to the implementation and add a note
on expected caller context.
* Rename iio_trigger_poll_chained() to iio_trigger_poll_nested() so
as to use more standard / common terminology.
* Improve main ABI docs references to offset and scale for raw values by
making them consistent and clear.
Cleanups and minor fixes:
* adi,ad5592r
- Add GPIO names - useful for debug.
* adi,ad7441r
- Fix current input, loop powered mode configuration setup.
* adi,adis16475
- Fix wrong commented value for minimum advised lower rate.
* adi,admv1013
- Use devm_clk_get_enabled() to reduce boilerplate.
* adi,ads1210
- Fix wrong bits for writing config register (late fix and has
been broken a long time so not rushed upstream)
* amlogic,meson-saradc
- Improve cleanup in error handling if BL30 handshake fails.
* apex-embedded,stx104
- Migrate to regmap and use regmap_read_poll_timeout() to neatly handle
retries.
- Add local mutex to close various races.
- Use define U16_MAX rather than value for limit.
- Improve code readability with minor reorganization.
* atmel,ad91-sama5d2
- Drop trivial dead code.
* kionix,kx022a
- Drop unused structure element.
* linear,ltc2983
- Reorganize bindings doc to enable unevaluatedProperties to be set
in one place for all child nodes.
- Make binding for adi,custom-thermocouple accept signed values.
* maxim,max44000
- Add OF Device matching (of_match_table was not correctly set).
* maxim,max5522
- Missing static
* measurement-computing,cio-dac
- Fix wrong part name in comments.
- Migrate to regmap.
- Improve includes by replacing bitops.h with more direct bits.h
* qcom,pm8xxx-xoadc
- Remove a check that can never fail.
* renesas,rcar-gyroadc
- DT binding documentation improvements.
- Tidy up an unused warning with __maybe_unused.
* semtech,sx_common
- Drop docs for a structure element that doesn't exist.
* semtech,sx9500
- Drop ACPI_PTR() and of_match_ptr() protections that just complicate
the code / block some firmware registration types that would otherwise
work.
* sensiron,sps30
- Comment formatting tidy up.
* st,sensors
- Drop duplicate text in DT binding.
* st,stm32-adc
- Add some missing static markings.
* ti,ads1100
- Use correct return code in dev_err_probe() call.
* x-powers,axp20x_adc - precursor series to simplify addition of AXP192.
- General code cleanup / minor refactoring for better readabilty of code.
- Switch from boolean value to mask for adc_en2 field to avoid hard coding
a mask that will be different in AXP192
* tag 'iio-for-6.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (63 commits)
MAINTAINERS: Add ROHM BU27034
iio: light: ROHM BU27034 Ambient Light Sensor
dt-bindings: iio: light: Support ROHM BU27034
MAINTAINERS: Add IIO gain-time-scale helpers
iio: light: Add gain-time-scale helpers
doc: Make sysfs-bus-iio doc more exact
iio: dac: set variable max5522_channels storage-class-specifier to static
dt-bindings: iio: temperature: ltc2983: Make 'adi,custom-thermocouple' signed
dt-bindings: iio: temperature: ltc2983: Fix child node unevaluated properties
iio: addac: stx104: Use regmap_read_poll_timeout() for conversion poll
iio: addac: stx104: Migrate to the regmap API
iio: addac: stx104: Improve indentation in stx104_write_raw()
iio: addac: stx104: Use define rather than hardcoded limit for write val
iio: addac: stx104: Fix race condition when converting analog-to-digital
iio: addac: stx104: Fix race condition for stx104_write_raw()
dt-bindings: iio: st-sensors: Fix repeated text
staging: iio: resolver: ads1210: fix config mode
iio: adc: ti-ads1100: fix error code in probe()
iio: accel: add support for IIS328DQ variant
dt-bindings: iio: st-sensors: Add IIS328DQ accelerometer
...
|
|
Add myself as a maintainer for ROHM BU27034 ALS driver.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/eac4b5f7fc8adcaac59ffa73e46cd7bb9c90edfa.1680263956.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
ROHM BU27034 is an ambient light sensor with 3 channels and 3 photo diodes
capable of detecting a very wide range of illuminance. Typical application
is adjusting LCD and backlight power of TVs and mobile phones.
Add initial support for the ROHM BU27034 ambient light sensor.
NOTE:
- Driver exposes 4 channels. One IIO_LIGHT channel providing the
calculated lux values based on measured data from diodes #0 and
#1. In addition, 3 IIO_INTENSITY channels are emitting the raw
register data from all diodes for more intense user-space
computations.
- Sensor has GAIN values that can be adjusted from 1x to 4096x.
- Sensor has adjustible measurement times of 5, 55, 100, 200 and
400 mS. Driver does not support 5 mS which has special
limitations.
- Driver exposes standard 'scale' adjustment which is
implemented by:
1) Trying to adjust only the GAIN
2) If GAIN adjustment alone can't provide requested
scale, adjusting both the time and the gain is
attempted.
- Driver exposes writable INT_TIME property that can be used
for adjusting the measurement time. Time adjustment will also
cause the driver to try to adjust the GAIN so that the
overall scale is kept as close to the original as possible.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/2a7efb6f335da5526fbe34b95137c5e45db5c5d3.1680263956.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
ROHM BU27034 is an ambient light sesnor with 3 channels and 3 photo diodes
capable of detecting a very wide range of illuminance. Typical application
is adjusting LCD and backlight power of TVs and mobile phones.
Add dt-bindings.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/66a222574176ee2adbfccf6d9a591c04571a18d9.1680263956.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add myself as a maintainer for IIO light sensor helpers (helpers for
maintaining the scale while adjusting intergration time or gain) and
related Kunit tests.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/d46414eabe8dd4cd3edb15f859f3b93cd406d9aa.1680263956.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Some light sensors can adjust both the HW-gain and integration time.
There are cases where adjusting the integration time has similar impact
to the scale of the reported values as gain setting has.
IIO users do typically expect to handle scale by a single writable 'scale'
entry. Driver should then adjust the gain/time accordingly.
It however is difficult for a driver to know whether it should change
gain or integration time to meet the requested scale. Usually it is
preferred to have longer integration time which usually improves
accuracy, but there may be use-cases where long measurement times can be
an issue. Thus it can be preferable to allow also changing the
integration time - but mitigate the scale impact by also changing the gain
underneath. Eg, if integration time change doubles the measured values,
the driver can reduce the HW-gain to half.
The theory of the computations of gain-time-scale is simple. However,
some people (undersigned) got that implemented wrong for more than once.
Add some gain-time-scale helpers in order to not dublicate errors in all
drivers needing these computations.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/268d418e7cffcdaa2ece6738478bbc57692c213e.1680263956.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
A few IIC channel descriptions explained used units as:
data is in foo "that can be processed into an" [unit] value. The "can be
processed into" is quite broad statement as it does not really explain
what this processing means. This makes units pretty much useless.
After discussion with Jonathan, it seems the units for these channels
should also be well-defined as for all other channels. The processing
means the standard scale and offset application that is used throughout
the IIO. Let's make it more obvious by stating that the units are [unit]
after scale ane offset are applied.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/41eafb0caa510cddf650cf5ff940639a184f3005.1677331779.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
smatch reports
drivers/iio/dac/max5522.c:55:28: warning: symbol
'max5522_channels' was not declared. Should it be static?
This variable is only used in one file so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230404013828.1914523-1-trix@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The 'adi,custom-thermocouple' property is signed based on the example
and driver, so it's type should be int64-matrix rather than
uint64-matrix.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230404205014.644336-2-robh@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The child node schemas are missing 'unevaluatedProperties' constraints,
so any unknown properties are allowed. The current structure with
multiple patternProperties schemas doesn't work for
unevaluatedProperties as each sub-schema is evaluated independently. To
fix this, move the sub-schema for all child nodes to a $defs entry and
reference it from each named child node.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230404205014.644336-1-robh@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
ADC sample captures take a certain amount of time to complete after
initiated; this conversion time range can be anywhere from 5
microseconds to 53.68 seconds depending on the configuration of the
Analog Input Frame Timer register. When the conversion is in progress,
the ADC Status register CNV bit is high. Call regmap_read_poll_timeout()
to poll until the ADC conversion is completed (or timeout if more than
53.68 seconds passes).
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/9ef433f107afd1d4dcd2d97ef0e932d7045c2bbd.1680790580.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
In addition, to improve code organization in stx104_probe(), the
devm_iio_device_register() call is moved above GPIO configuration in
order to keep relevant code closer together.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/0bcdfc4738cc019fb2ff83f61eb46a3488bc166d.1680790580.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
By bailing out early if chan->output is false for the IIO_CHAN_INFO_RAW,
indentation can be decreased by a tab and code readability improved.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/487d17da9e2612f3e6b2bd1c3def2fa1b955db9b.1680790580.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The DAC register is 16 bits wide, so the value passed by write_raw()
should be checked against that limit. Rather than hardcoding the 16-bit
maximum value limit, use a define to improve readability and make the
intention of the code clearer. The explicit cast is also avoided by
instead explicitly checking for negative values.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/4c9f4f1b4a270d133be70c82a091351b531b5e3e.1680790580.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ADC conversion procedure requires several device I/O operations
performed in a particular sequence. If stx104_read_raw() is called
concurrently, the ADC conversion procedure could be clobbered. Prevent
such a race condition by utilizing a mutex.
Fixes: 4075a283ae83 ("iio: stx104: Add IIO support for the ADC channels")
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/2ae5e40eed5006ca735e4c12181a9ff5ced65547.1680790580.git.william.gray@linaro.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The priv->chan_out_states array and actual DAC value can become
mismatched if stx104_write_raw() is called concurrently. Prevent such a
race condition by utilizing a mutex.
Fixes: 97a445dad37a ("iio: Add IIO support for the DAC on the Apex Embedded Systems STX104")
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/c95c9a77fcef36b2a052282146950f23bbc1ebdc.1680790580.git.william.gray@linaro.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The description oddly contains a copy of the initial paragraph.
Let's not repeat ourselves.
Suggested-by: Diederik de Haas <didi.debian@cknow.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230329074614.1037625-1-linus.walleij@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
As stated in the device datasheet [1], bits a0 and a1 have to be set to
1 for the configuration mode.
[1]: https://www.analog.com/media/en/technical-documentation/data-sheets/ad2s1210.pdf
Fixes: b19e9ad5e2cb9 ("staging:iio:resolver:ad2s1210 general driver cleanup")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230327145414.1505537-1-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This code has a copy and paste bug so it accidentally returns
"PTR_ERR(data->reg_vdd)" which is a valid pointer cast to int. It
should return "ret" instead.
Fixes: 541880542f2b ("iio: adc: Add TI ADS1100 and ADS1000")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/36fa2aeb-f392-4793-8b38-ae15514033c8@kili.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We need it here to apply other char/misc driver changes to.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Fix "same task" check when redirecting event output
- Do not wait unconditionally for RCU on the event migration path if
there are no events to migrate
* tag 'perf_urgent_for_v6.3_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix the same task check in perf_event_set_output
perf: Optimize perf_pmu_migrate_context()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Add a new Intel Arrow Lake CPU model number
- Fix a confusion about how to check the version of the ACPI spec which
supports a "online capable" bit in the MADT table which lead to a
bunch of boot breakages with Zen1 systems and VMs
* tag 'x86_urgent_for_v6.3_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add model number for Intel Arrow Lake processor
x86/acpi/boot: Correct acpi_is_processor_usable() check
x86/ACPI/boot: Use FADT version to check support for online capable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull compute express link (cxl) fixes from Dan Williams:
"Several fixes for driver startup regressions that landed during the
merge window as well as some older bugs.
The regressions were due to a lack of testing with what the CXL
specification calls Restricted CXL Host (RCH) topologies compared to
the testing with Virtual Host (VH) CXL topologies. A VH topology is
typical PCIe while RCH topologies map CXL endpoints as Root Complex
Integrated endpoints. The impact is some driver crashes on startup.
This merge window also added compatibility for range registers (the
mechanism that CXL 1.1 defined for mapping memory) to treat them like
HDM decoders (the mechanism that CXL 2.0 defined for mapping
Host-managed Device Memory). That work collided with the new region
enumeration code that was tested with CXL 2.0 setups, and fails with
crashes at startup.
Lastly, the DOE (Data Object Exchange) implementation for retrieving
an ACPI-like data table from CXL devices is being reworked for v6.4.
Several fixes fell out of that work that are suitable for v6.3.
All of this has been in linux-next for a while, and all reported
issues [1] have been addressed.
Summary:
- Fix several issues with region enumeration in RCH topologies that
can trigger crashes on driver startup or shutdown.
- Fix CXL DVSEC range register compatibility versus region
enumeration that leads to startup crashes
- Fix CDAT endiannes handling
- Fix multiple buffer handling boundary conditions
- Fix Data Object Exchange (DOE) workqueue usage vs
CONFIG_DEBUG_OBJECTS warn splats"
Link: http://lore.kernel.org/r/20230405075704.33de8121@canb.auug.org.au [1]
* tag 'cxl-fixes-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/hdm: Extend DVSEC range register emulation for region enumeration
cxl/hdm: Limit emulation to the number of range registers
cxl/region: Move coherence tracking into cxl_region_attach()
cxl/region: Fix region setup/teardown for RCDs
cxl/port: Fix find_cxl_root() for RCDs and simplify it
cxl/hdm: Skip emulation when driver manages mem_enable
cxl/hdm: Fix double allocation of @cxlhdm
PCI/DOE: Fix memory leak with CONFIG_DEBUG_OBJECTS=y
PCI/DOE: Silence WARN splat with CONFIG_DEBUG_OBJECTS=y
cxl/pci: Handle excessive CDAT length
cxl/pci: Handle truncated CDAT entries
cxl/pci: Handle truncated CDAT header
cxl/pci: Fix CDAT retrieval on big endian
|
|
git://git.samba.org/sfrench/cifs-2.6
Pull cifs client fixes from Steve French:
"Two cifs/smb3 client fixes, one for stable:
- double lock fix for a cifs/smb1 reconnect path
- DFS prefixpath fix for reconnect when server moved"
* tag '6.3-rc5-smb3-cifs-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: double lock in cifs_reconnect_tcon()
cifs: sanitize paths in cifs_update_super_prepath.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a small set of various small driver changes for 6.3-rc6.
Included in here are:
- iio driver fixes for reported problems
- coresight hwtracing bugfix for reported problem
- small counter driver bugfixes
All have been in linux-next for a while with no reported problems"
* tag 'char-misc-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
coresight: etm4x: Do not access TRCIDR1 for identification
coresight-etm4: Fix for() loop drvdata->nr_addr_cmp range bug
iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip
iio: adc: palmas_gpadc: fix NULL dereference on rmmod
counter: 104-quad-8: Fix Synapse action reported for Index signals
counter: 104-quad-8: Fix race condition between FLAG and CNTR reads
iio: adc: max11410: fix read_poll_timeout() usage
iio: dac: cio-dac: Fix max DAC write value check for 12-bit
iio: light: cm32181: Unregister second I2C client if present
iio: accel: kionix-kx022a: Get the timestamp from the driver's private data in the trigger_handler
iio: adc: ad7791: fix IRQ flags
iio: buffer: make sure O_NONBLOCK is respected
iio: buffer: correctly return bytes written in output buffers
iio: light: vcnl4000: Fix WARN_ON on uninitialized lock
iio: adis16480: select CONFIG_CRC32
drivers: iio: adc: ltc2497: fix LSB shift
iio: adc: qcom-spmi-adc5: Fix the channel name
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for some reported
problems:
- fsl_uart driver bugfixes
- sh-sci serial driver bugfixes
- renesas serial driver DT binding bugfixes
- 8250 DMA bugfix
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: sh-sci: Fix Rx on RZ/G2L SCI
tty: serial: fsl_lpuart: fix crash in lpuart_uport_is_active
tty: serial: fsl_lpuart: avoid checking for transfer complete when UARTCTRL_SBK is asserted in lpuart32_tx_empty
serial: 8250: Prevent starting up DMA Rx on THRI interrupt
dt-bindings: serial: renesas,scif: Fix 4th IRQ for 4-IRQ SCIFs
tty: serial: sh-sci: Fix transmit end interrupt handler
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB bugfixes from Greg KH:
"Here are some small USB bugfixes for 6.3-rc6 that have been in my
tree, and in linux-next, for a while. Included in here are:
- new usb-serial driver device ids
- xhci bugfixes for reported problems
- gadget driver bugfixes for reported problems
- dwc3 new device id
All have been in linux-next with no reported problems"
* tag 'usb-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: cdnsp: Fixes error: uninitialized symbol 'len'
usb: gadgetfs: Fix ep_read_iter to handle ITER_UBUF
usb: gadget: f_fs: Fix ffs_epfile_read_iter to handle ITER_UBUF
usb: typec: altmodes/displayport: Fix configure initial pin assignment
usb: dwc3: pci: add support for the Intel Meteor Lake-S
xhci: Free the command allocated for setting LPM if we return early
Revert "usb: xhci-pci: Set PROBE_PREFER_ASYNCHRONOUS"
xhci: also avoid the XHCI_ZERO_64B_REGS quirk with a passthrough iommu
USB: serial: option: add Quectel RM500U-CN modem
usb: xhci: tegra: fix sleep in atomic call
USB: serial: option: add Telit FE990 compositions
USB: serial: cp210x: add Silicon Labs IFS-USB-DATACABLE IDs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes, all in drivers. They're all one or two lines except
for the ufs one, but that's a simple revert of a previous feature"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi_tcp: Check that sock is valid before iscsi_set_param()
scsi: qla2xxx: Fix memory leak in qla2x00_probe_one()
scsi: mpi3mr: Handle soft reset in progress fault code (0xF002)
scsi: Revert "scsi: ufs: core: Initialize devfreq synchronously"
|
|
Pull block fixes from Jens Axboe:
- Ensure that ublk always reads the whole sqe upfront (me)
- Fix for a block size probing issue with ublk (Ming)
- Fix for the bio based polling (Keith)
- NVMe pull request via Christoph:
- fix discard support without oncs (Keith Busch)
- Partition scan error handling regression fix (Yu)
* tag 'block-6.3-2023-04-06' of git://git.kernel.dk/linux:
block: don't set GD_NEED_PART_SCAN if scan partition failed
block: ublk: make sure that block size is set correctly
ublk: read any SQE values upfront
nvme: fix discard support without oncs
blk-mq: directly poll requests
|
|
Pull io_uring fixes from Jens Axboe:
"Just two minor fixes for provided buffers - one where we could
potentially leak a buffer, and one where the returned values was
off-by-one in some cases"
* tag 'io_uring-6.3-2023-04-06' of git://git.kernel.dk/linux:
io_uring: fix memory leak when removing provided buffers
io_uring: fix return value when removing provided buffers
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fix from Christoph Hellwig:
- fix a braino in the swiotlb alignment check fix (Petr Tesarik)
* tag 'dma-mapping-6.3-2023-04-08' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: fix a braino in the alignment check fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
"A couple more minor fixes:
- Reset direct->addr back to its original value on error in updating
the direct trampoline code
- Make lastcmd_mutex static"
* tag 'trace-v6.3-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/synthetic: Make lastcmd_mutex static
ftrace: Fix issue that 'direct->addr' not restored in modify_ftrace_direct()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM fixes from Andrew Morton:
"28 hotfixes.
23 are cc:stable and the other five address issues which were
introduced during this merge cycle.
20 are for MM and the remainder are for other subsystems"
* tag 'mm-hotfixes-stable-2023-04-07-16-23' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (28 commits)
maple_tree: fix a potential concurrency bug in RCU mode
maple_tree: fix get wrong data_end in mtree_lookup_walk()
mm/swap: fix swap_info_struct race between swapoff and get_swap_pages()
nilfs2: fix sysfs interface lifetime
mm: take a page reference when removing device exclusive entries
mm: vmalloc: avoid warn_alloc noise caused by fatal signal
nilfs2: initialize "struct nilfs_binfo_dat"->bi_pad field
nilfs2: fix potential UAF of struct nilfs_sc_info in nilfs_segctor_thread()
zsmalloc: document freeable stats
zsmalloc: document new fullness grouping
fsdax: force clear dirty mark if CoW
mm/hugetlb: fix uffd wr-protection for CoW optimization path
mm: enable maple tree RCU mode by default
maple_tree: add RCU lock checking to rcu callback functions
maple_tree: add smp_rmb() to dead node detection
maple_tree: fix write memory barrier of nodes once dead for RCU mode
maple_tree: remove extra smp_wmb() from mas_dead_leaves()
maple_tree: fix freeing of nodes in rcu mode
maple_tree: detect dead nodes in mas_start()
maple_tree: be more cautious about dead nodes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix irq handling in gpio-davinci
- fix Kconfig dependencies for gpio-regmap
* tag 'gpio-fixes-for-v6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: davinci: Add irq chip flag to skip set wake
gpio: davinci: Do not clear the bank intr enable bit in save_context
gpio: GPIO_REGMAP: select REGMAP instead of depending on it
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"Fix the ACPI backlight override mechanism for the cases when
acpi_backlight=video is set through the kernel command line or a DMI
quirk and add backlight quirks for Apple iMac14,1 and iMac14,2 and
Lenovo ThinkPad W530 (Hans de Goede)"
* tag 'acpi-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: video: Add acpi_backlight=video quirk for Lenovo ThinkPad W530
ACPI: video: Add acpi_backlight=video quirk for Apple iMac14,1 and iMac14,2
ACPI: video: Make acpi_backlight=video work independent from GPU driver
ACPI: video: Add auto_detect arg to __acpi_video_get_backlight_type()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Fix uninitialised variable warning (from smatch) in the arm64 compat
alignment fixup code"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: compat: Work around uninitialized variable warning
|
|
Pull ksmbd server fixes from Steve French:
"Four fixes, three for stable:
- slab out of bounds fix
- lock cancellation fix
- minor cleanup to address clang warning
- fix for xfstest 551 (wrong parms passed to kvmalloc)"
* tag '6.3-rc5-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: fix slab-out-of-bounds in init_smb2_rsp_hdr
ksmbd: delete asynchronous work from list
ksmbd: remove unused is_char_allowed function
ksmbd: do not call kvmalloc() with __GFP_NORETRY | __GFP_NO_WARN
|
|
This lock was supposed to be an unlock.
Fixes: 6cc041e90c17 ("cifs: avoid races in parallel reconnects in smb1")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Currently if disk_scan_partitions() failed, GD_NEED_PART_SCAN will still
set, and partition scan will be proceed again when blkdev_get_by_dev()
is called. However, this will cause a problem that re-assemble partitioned
raid device will creat partition for underlying disk.
Test procedure:
mdadm -CR /dev/md0 -l 1 -n 2 /dev/sda /dev/sdb -e 1.0
sgdisk -n 0:0:+100MiB /dev/md0
blockdev --rereadpt /dev/sda
blockdev --rereadpt /dev/sdb
mdadm -S /dev/md0
mdadm -A /dev/md0 /dev/sda /dev/sdb
Test result: underlying disk partition and raid partition can be
observed at the same time
Note that this can still happen in come corner cases that
GD_NEED_PART_SCAN can be set for underlying disk while re-assemble raid
device.
Fixes: e5cfefa97bcc ("block: fix scan partition for exclusively open device again")
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
