| Age | Commit message (Collapse) | Author |
|---|
|
Add binding document for serial bluetooth chips using Qualcomm protocol.
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add a new serial node for the Qualcomm BT controller QCA6174. This
allows automatic probing and hci registration through the serdev
framework instead of relying on the userspace helpers.
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch enables regulators and gpios for the Qualcomm QCA6174 BT/WLAN
combo controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The node name for a PCIe host bridge must be "pcie" as required by
the binging. dtc now warns about it:
arch/arm64/boot/dts/qcom/apq8096-db820c.dtb: Warning (pci_bridge): /soc/agnoc@0/qcom,pcie@610000: node name is not "pci" or "pcie"
arch/arm64/boot/dts/qcom/apq8096-db820c.dtb: Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
arch/arm64/boot/dts/qcom/msm8996-mtp.dtb: Warning (pci_bridge): /soc/agnoc@0/qcom,pcie@610000: node name is not "pci" or "pcie"
arch/arm64/boot/dts/qcom/msm8996-mtp.dtb: Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
This renames the nodes as appropriate.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
With the addition of this ramoops node it enables post mortem
analysis if a debug cable is not attached and/or not available.
All addresses and values were extracted from CAF AOSP marshmallow
DR 1.6.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add a skeletal sdm845 SoC dtsi and MTP board dts/dtsi files
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This enables SDHCI on the Nexus 5X as well creates common smd_rpm node
which can be shared between both 5X and 6P as per HW design.
Given the lack of documentation, only downstream code was used as a reference
and it eludes to the fact that 8994-rpm-regulator is common between both msm8992
& msm8994. [ see msm.git branch: msm-angler-3.10-marshmallow-mr1, msm8992.dtsi]
At this early stage of development it makes sense for the 8994-rpm-regulator
to be common until data / documentation suggests otherwise.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
With the new rev.E of A20-SOM-EVB, there is option for 16GB eMMC.
Currently used card is KLMAG2GEND, wired to MMC2 slot.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
To avoid regressions, this patch changes the DTS files for the only two
users of this driver that didn't have this property yet.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On RDU1, sdhc1 is used for eMMC, and that is 3.3V only.
Thus configure device node not to probe it as SD/SDIO and not try 1.8V.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Vybrid has single internal temperature sensor connected to both internal
ADC modules.
vf610-zii-dev already has ADC0 enabled. Now, to get temperature sensor
captured by iio_hwmon driver, need to configure iio_hwmon node to use
that ADC.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch uses "operating-points-v2" instead of
"operating-points" to be more fit with cpufreq-dt
driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX7S does NOT support CPU frequency scaling, so no
need to specify the CPU regulator supply.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Correct CPU supply name to meet cpufreq-dt driver's
requirement for voltage scaling.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On RDU1, imx51 usbh1 interface is either not used, or used via external
block that breaks USB2 signalling.
To keep things working if high-speed device gets connected to that
block, use ChipIdea feature to limit port to full speed.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove unit-address and reg property from anatop regulators to fix
the following DTC warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddcore@20c8140: duplicate unit-address (also used in node /soc/aips-bus@2000000/anatop@20c8000/regulator-vddpu@20c8140)
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddcore@20c8140: duplicate unit-address (also used in node /soc/aips-bus@2000000/anatop@20c8000/regulator-vddsoc@20c8140)
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddpu@20c8140: duplicate unit-address (also used in node /soc/aips-bus@2000000/anatop@20c8000/regulator-vddsoc@20c8140)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are some LED's attached to the GPIO expander, and
there are is a bank of switches attached to the GPIO expander.
This patch associates the LED and the switches to it.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There is a tca6416 GPIO expander on i2c2. This patch enables the
GPIO expander which has several LED's and some connected DIP
switches
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add pin control information for the NAND interface on the Armada
98DX3236 and variants.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This allows to reference these gpio controller as interrupt parent. Also
add a comment which cpu line names are managed by the controllers
because "nb" and "sb" usually doesn't appear in schematics, but MPPX_Y
do.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This patch adds a fixed-link node to the 10G interface of the 7040-db
board. This is required as the mvpp2 driver now uses phylink. The best
solution would have been to describe the SFP cage but they are not
wired correctly, and thus unusable, so we chose to use fixed-link
instead.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This patch adds a fixed-link node to both 10G interfaces of the 8040-db
board. This is required as the mvpp2 driver now uses phylink. The best
solution would have been to describe the SFP cages but they are not
wired correctly, and thus unusable, so we chose to use fixed-link
instead.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This patch enables the fourth network interface on the Marvell
Macchiatobin. It is configured in the 2500Base-X PHY mode. The SFP cage
is also described.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This patch adds the SFP cage description in the Marvell Armada 8040
mcbin, for both 10G interfaces.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[Antoine: small reworks, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The Bananapi M2 Ultra has a Realtek RTL8211E RGMII PHY tied to the GMAC.
The PMIC's DC1SW output provides power for the PHY, while the ALDO2
output provides I/O voltages on both sides.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The R40 SoC has a GMAC (gigabit capable Ethernet controller). Add a
device node for it. The only publicly available board for this SoC
uses an RGMII PHY. Add a pinmux node for it as well.
Since this SoC also has an old 10/100 Mbps EMAC, which also has an
MDIO bus controller, the MDIO bus for the GMAC is labeled "gmac_mdio".
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The device nodes dereference (&foo) usages should be sorted by the label
names, barring any parsing order issues such as the #include statement
for the PMIC's .dtsi file that must come after the PMIC.
Move the mmc and ohci blocks in front of the PMIC's regulator blocks.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The legacy mode uses the write protect and card detect but DT does not.
This patch enables Write-Protect and Card-Detect pins for the MMC card, and
the gpio-ranges property sets the gpio pinmuxing for those respective pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
All iommus got their clocks added and rk3399 got support for its
usb3-phy otg-port and better ajustment for the cpll child clocks.
On the board side, all rk3399 got their typec phys enabled - which
is needed for better usb support, the sapphire board got some more
properties moved to the excavator baseboard where they really belong,
kevin got a fix to use a real devicetree compatible and puma-haikou
got its hdmi port enabled.
* tag 'v4.18-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: enable hdmi on rk3399-puma-haikou
arm64: dts: rockchip: use canonical compatible for touchpad/touchscreen on gru-kevin
arm64: dts: rockchip: add clocks in iommu nodes
arm64: dts: rockchip: add usb3-phy otg-port support for rk3399
arm64: dts: rockchip: remove PCIe assigned-clocks in excavator baseboard
arm64: dts: rockchip: move rk3399-sapphire PCIe to excavator baseboard
arm64: dts: rockchip: assign clock rate for cpll child clocks on rk3399
arm64: dts: rockchip: enable typec-phy0 for rk3399-puma-haikou
arm64: dts: rockchip: enable typec-phy1 for rk3399-puma
arm64: dts: rockchip: enable typec-phy for rk3399-firefly
arm64: dts: rockchip: enable typec-phy for rk3399-sapphire
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Fixed pin numbers for uart4 on rk3288, iommu clocks and small changes
over multiple boards like default serial setting for rk3288-tinker,
output selection for the dp83867 on the phycore-som and the newly
added pwm-backlight delay properties for veyron boards.
* tag 'v4.18-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: default serial for rk3288 Tinker Board
ARM: dts: rockchip: set PWM delay backlight settings for Minnie
ARM: dts: rockchip: set PWM delay backlight settings for Veyron
ARM: dts: rockchip: add clocks in iommu nodes
ARM: dts: rockchip: Add dp83867 CLK_OUT muxing on rk3288-phycore-som
ARM: dts: rockchip: fix uart4 pin-numbers for rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
ARMv8 Juno/Vexpress updates/cleanups for v4.18
1. Add the missing connections to the STM output port as all endpoint
connections must be bidirectional.
2. Replace all the custom OF graph endpoint node names with the standard
'endpoint'
3. Cleanup to replace all underscores('_') with hyphens('-') in the
device node names
4. Syntactic restructuring of motherboard include file so that it can be
included at the top of any other DTS file as it should be rather than
existing include in the middle of the file at a specific location
* tag 'juno-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno/rtsm: re-structure motherboard includes
arm64: dts: juno: replace '_' with '-' in node names
arm64: dts: juno: Fix "debounce-interval" property misspelling
arm64: dts: juno: fix OF graph endpoint node names
arm64: dts: juno: fix missing Coresight STM graph connection
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
ARMv7 Vexpress updates/cleanups for v4.18
1. Syntactic restructuring of motherboard include file so that it can be
included at the top of any other DTS file as it should be rather than
existing include in the middle of the file at a specific location
2. Use of standard GPIO controller bindings for few sysreg components
like LED, MMC Write Protect/Card Detect and Flash Write Protect
to fix some of the new DTC warnings
3. Cleanup to replace all underscores('_') with hyphens('-') in the
device node names
* tag 'vexpress-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: replace '_' with '-' in node names
ARM: dts: vexpress: use standard gpio bindings for sys_{led,mci,flash}
ARM: dts: vexpress: Restructure motherboard includes
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/dt
STi DT update:
_ Fix complain about IRQ_TYPE_NONE_usage
* tag 'sti-dt-for-v4.18-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: stihxxx-b2120: Fix complain about IRQ_TYPE_NONE usage
ARM: dts: stih410: Fix complain about IRQ_TYPE_NONE usage
ARM: dts: stih407: Fix complain about IRQ_TYPE_NONE usage
ARM: dts: stih407-pinctrl: Fix complain about IRQ_TYPE_NONE usage
ARM: dts: stih407-family: Fix complain about IRQ_TYPE_NONE usage
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/dt
- add clock and pinctrl nodes for mt2712e
- add High-Speed DMA and audio nodes for mt7622
* tag 'v4.17-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt7622: add audio related device nodes
arm64: dts: mt7622: add High-Speed DMA device nodes
arm64: dts: mt2712: add pintcrl device node.
arm64: dts: mt2712: add pintcrl file
arm64: dts: add clock device nodes of MT2712
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/dt
convert to SPDX IDs
mt7623:
- add audio, bluetooth, highspees DMA and SPI-NOR nodes
- fix invalid memory nodes by not using skeleton64.dtsi
- fix memory size for bananapi-r2
- fix dtc warnings
- refactor dts and dtsi to aviod code duplication
- add mt7623n and mt7623a reference boards
* tag 'v4.17-next-dts32' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm: dts: mt7623: add MT7623N reference board with eMMC
arm: dts: mt7623: add MT7623A reference boards
arm: dts: mt7623: add MT7623A SoC level DTS
arm: dts: mt7623: extend common file reused by all boards with MT7623 SoCs
arm: dts: mt6323: move node mt6323 leds to mt6323.dtsi
arm: dts: mt7623: add BTIF, HSDMA and SPI-NOR device nodes
arm: dts: mt7623: fix all Warnings (unit_address_vs_reg)
arm: dts: mt7623: fix available memory size on bananapi-r2
arm: dts: mt7623: fix invalid memory node being generated
arm: dts: mediatek: converted to using SPDX identifiers
arm: dts: mediatek: modify audio related nodes for both MT2701 and MT7623
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The touchscreen patch did not apply to this branch correctly and
inadvertently got placed onto I2C2 when it should be on I2C3. This fixes
the issue.
Fixes: 121685b14624 ("ARM: dts: logicpd-som-lv: Enable Touchscreen
controller")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The SOM used in the am3517-evm has a s35390a onboard. This
patch allows the s35390a to be used as the RTC.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
enable mmc3 used for wlan and uart1 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The AM3517-EVM by Logic PD has a Logic PD type 15 display LCD
attached to the baseboard, and the SOM itself has an integrated
touchscreen controller. This patch enables both the LCD and
the tsc2004 on the SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The am3517-som is powered by vdd_core_reg, so let's add the
'cpu' device-tree node with the 'vdd_core' regulator as the core
supply.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This commit adds the common voltage regulators used on LogicPD's
AM3517 System-On-Modules.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The am3517-evm consists of an am3517 SOM-M2 and a baseboard.
As items are added that are unique to the baseboard, let's place
them in a file called am3517-som.dtsi. These items will be
common for all variants of the SOM.
Anything unique to the baseboard will be placed into
am3517-evm.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The boardboard supports card detect and write protect, so let's
enable those pins.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The board uses 26MHz oscillator for the twl4030 HFCLK. This way we will
not depend on the bootloader to configure the CFG_BOOT:HFCLK_FREQ
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The board uses 26MHz oscillator for the twl4030 HFCLK.
This way we will not depend on the bootloader to configure the
CFG_BOOT:HFCLK_FREQ
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Replace magic number with the proper IRQ_TYPE specifier to improve DT
readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
