| Age | Commit message (Collapse) | Author |
|---|
|
On Qualcomm chipsets not all GPIOs are wakeup capable. Those GPIOs do not
have a corresponding MPM pin and should not be handled inside the MPM
driver. The IRQ domain hierarchy is always applied, so it's required to
explicitly disconnect the hierarchy for those. The pinctrl-msm driver marks
these with GPIO_NO_WAKE_IRQ. qcom-pdc has a check for this, but
irq-qcom-mpm is currently missing the check. This is causing crashes when
setting up interrupts for non-wake GPIOs:
root@rb1:~# gpiomon -c gpiochip1 10
irq: IRQ159: trimming hierarchy from :soc@0:interrupt-controller@f200000-1
Unable to handle kernel paging request at virtual address ffff8000a1dc3820
Hardware name: Qualcomm Technologies, Inc. Robotics RB1 (DT)
pc : mpm_set_type+0x80/0xcc
lr : mpm_set_type+0x5c/0xcc
Call trace:
mpm_set_type+0x80/0xcc (P)
qcom_mpm_set_type+0x64/0x158
irq_chip_set_type_parent+0x20/0x38
msm_gpio_irq_set_type+0x50/0x530
__irq_set_trigger+0x60/0x184
__setup_irq+0x304/0x6bc
request_threaded_irq+0xc8/0x19c
edge_detector_setup+0x260/0x364
linereq_create+0x420/0x5a8
gpio_ioctl+0x2d4/0x6c0
Fix this by copying the check for GPIO_NO_WAKE_IRQ from qcom-pdc.c, so that
MPM is removed entirely from the hierarchy for non-wake GPIOs.
Fixes: a6199bb514d8 ("irqchip: Add Qualcomm MPM controller driver")
Reported-by: Alexey Klimov <alexey.klimov@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250502-irq-qcom-mpm-fix-no-wake-v1-1-8a1eafcd28d4@linaro.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two minor updates, both in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Remove redundant query_complete trace
scsi: myrb: Fix spelling mistake "statux" -> "status"
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request via Christoph:
- fix queue unquiesce check on PCI slot_reset (Keith Busch)
- fix premature queue removal and I/O failover in nvme-tcp (Michael
Liang)
- don't restore null sk_state_change (Alistair Francis)
- select CONFIG_TLS where needed (Alistair Francis)
- always free derived key data (Hannes Reinecke)
- more quirks (Wentao Guan)
- ublk zero copy fix
- ublk selftest fix for UBLK_F_NEED_GET_DATA
* tag 'block-6.15-20250502' of git://git.kernel.dk/linux:
nvmet-auth: always free derived key data
nvmet-tcp: don't restore null sk_state_change
nvmet-tcp: select CONFIG_TLS from CONFIG_NVME_TARGET_TCP_TLS
nvme-tcp: select CONFIG_TLS from CONFIG_NVME_TCP_TLS
nvme-tcp: fix premature queue removal and I/O failover
nvme-pci: add quirks for WDC Blue SN550 15b7:5009
nvme-pci: add quirks for device 126f:1001
nvme-pci: fix queue unquiesce check on slot_reset
ublk: remove the check of ublk_need_req_ref() from __ublk_check_and_get_req
ublk: enhance check for register/unregister io buffer command
ublk: decouple zero copy from user copy
selftests: ublk: fix UBLK_F_NEED_GET_DATA
|
|
Pull io_uring fix from Jens Axboe:
"Just a single fix, annotating the fdinfo side SQ/CQ head/tail reads
with data_race() as they are known racy.
Only serves to silence syzbot testing, by definition these debug
outputs are going to be racy as they may change as soon as we've read
them"
* tag 'io_uring-6.15-20250502' of git://git.kernel.dk/linux:
io_uring/fdinfo: annotate racy sq/cq head/tail reads
|
|
Pull bcachefs fixes from Kent Overstreet:
"Lots of assorted small fixes...
- Some repair path fixes, a fix for -ENOMEM when reconstructing lots
of alloc info on large filesystems, upgrade for ancient 0.14
filesystems, etc.
- Various assert tweaks; assert -> ERO, ERO -> log the error in the
superblock and continue
- casefolding now uses d_ops like on other casefolding filesystems
- fix device label create on device add, fix bucket array resize on
filesystem resize
- fix xattrs with FORTIFY_SOURCE builds with gcc-15/clang"
* tag 'bcachefs-2025-05-01' of git://evilpiepirate.org/bcachefs: (22 commits)
bcachefs: Remove incorrect __counted_by annotation
bcachefs: add missing sched_annotate_sleep()
bcachefs: Fix __bch2_dev_group_set()
bcachefs: Kill ERO for i_blocks check in truncate
bcachefs: check for inode.bi_sectors underflow
bcachefs: Kill ERO in __bch2_i_sectors_acct()
bcachefs: readdir fixes
bcachefs: improve missing journal write device error message
bcachefs: Topology error after insert is now an ERO
bcachefs: Use bch2_kvmalloc() for journal keys array
bcachefs: More informative error message when shutting down due to error
bcachefs: btree_root_unreadable_and_scan_found_nothing autofix for non data btrees
bcachefs: btree_node_data_missing is now autofix
bcachefs: Don't generate alloc updates to invalid buckets
bcachefs: Improve bch2_dev_bucket_missing()
bcachefs: fix bch2_dev_buckets_resize()
bcachefs: Add upgrade table entry from 0.14
bcachefs: Run BCH_RECOVERY_PASS_reconstruct_snapshots on missing subvol -> snapshot
bcachefs: Add missing utf8_unload()
bcachefs: Emit unicode version message on startup
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix potential NULL dereference in the i.MX driver
- Fix the pull up/down resistor values in the Meson driver
- Fix the mapping of the PHY LED pins in the Airhoa driver
- Fix EINT interrupts on older controllers and a debounce value issue
in the Mediatek driver
- Fix an erronoeus PINGROUP define in the Qualcomm driver
* tag 'pinctrl-v6.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: Fix PINGROUP definition for sm8750
pinctrl: mediatek: common-v1: Fix error checking in mtk_eint_init()
pinctrl: mediatek: Fix new design debounce issue
pinctrl: mediatek: common-v1: Fix EINT breakage on older controllers
pinctrl: airoha: fix wrong PHY LED mapping and PHY2 LED defines
pinctrl: meson: define the pull up/down resistor value as 60 kOhm
pinctrl: imx: Return NULL if no group is matched and found
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu fixes from Joerg Roedel:
"ARM-SMMU fixes:
- Fix broken detection of the S2FWB feature
- Ensure page-size bitmap is initialised for SVA domains
- Fix handling of SMMU client devices with duplicate Stream IDs
- Don't fail SMMU probe if Stream IDs are aliased across clients
Intel VT-d fixes:
- Add quirk for IGFX device
- Revert an ATS change to fix a boot failure
AMD IOMMU:
- Fix potential buffer overflow
Core:
- Fix for iommu_copy_struct_from_user()"
* tag 'iommu-fixes-v6.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
iommu/vt-d: Apply quirk_iommu_igfx for 8086:0044 (QM57/QS57)
iommu/vt-d: Revert ATS timing change to fix boot failure
iommu: Fix two issues in iommu_copy_struct_from_user()
iommu/amd: Fix potential buffer overflow in parse_ivrs_acpihid
iommu/arm-smmu-v3: Fail aliasing StreamIDs more gracefully
iommu/arm-smmu-v3: Fix iommu_device_probe bug due to duplicated stream ids
iommu/arm-smmu-v3: Fix pgsize_bit for sva domains
iommu/arm-smmu-v3: Add missing S2FWB feature detection
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab fix from Vlastimil Babka:
- Stable fix to avoid bugs due to leftover obj_ext after allocation
profiling is disabled at runtime (Zhenhua Huang)
* tag 'slab-for-6.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm, slab: clean up slab->obj_exts always
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
i2c-host-fixes for v6.15-rc5
- imx-lpi2c: fix error handling sequence in probe
|
|
On 32bits ARM, u64/u64 is not supported [1], so change the algorithm
to use a simple fifo with decimal digits as u8 instead.
This is slower but should compile on all architecture.
Link: https://lore.kernel.org/dri-devel/CANiq72ke45eOwckMhWHvmwxc03dxr4rnxxKvx+HvWdBLopZfrQ@mail.gmail.com/ [1]
Reported-by: Miguel Ojeda <ojeda@kernel.org>
Closes: https://lore.kernel.org/dri-devel/CANiq72ke45eOwckMhWHvmwxc03dxr4rnxxKvx+HvWdBLopZfrQ@mail.gmail.com/
Fixes: ccb8ce526807 ("ARM: 9441/1: rust: Enable Rust support for ARMv7")
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250418165059.560503-1-jfalempe@redhat.com
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
|
|
The function are defined in the rcar_cmm.c file, but not called
elsewhere, so delete the unused function.
drivers/gpu/drm/renesas/rcar-du/rcar_cmm.c:35:19: warning: unused function 'rcar_cmm_read'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=9364
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20240619075436.86407-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
|
|
The rcar_du_vsps_init() doesn't free the np allocated by
of_parse_phandle_with_fixed_args() for the non-error case.
Fix memory leak for the non-error case.
While at it, replace the label 'error'->'done' as it applies to non-error
case as well and update the error check condition for rcar_du_vsp_init()
to avoid breakage in future, if it returns positive value.
Fixes: 3e81374e2014 ("drm: rcar-du: Support multiple sources from the same VSP")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20231116122424.80136-1-biju.das.jz@bp.renesas.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
drm-misc-next for v6.16-rc1:
UAPI Changes:
- panthor now fails in mmap_offset call for a BO created with
DRM_PANTHOR_BO_NO_MMAP.
- Add DRM_PANTHOR_BO_SET_LABEL ioctl and label panthor kernel BOs.
Cross-subsystem Changes:
- Add kmap_local_page_try_from_panic for drm/panic.
- Add DT bindings for panels.
- Update DT bindings for imagination.
- Extend %p4cc in lib/vsprintf.c to support fourcc printing.
Core Changes:
- Remove the disgusting turds.
- Register definition updates for DP.
- DisplayID timing blocks refactor.
- Remove now unused mipi_dsi_dsc_write_seq.
- Convert panel drivers to not return error in prepare/enable and
unprepare/disable calls.
Driver Changes:
- Assorted small fixes and featuers for rockchip, panthor, accel/ivpu,
accel/amdxdna, hisilicon/hibmc, i915/backlight, sysfb, accel/qaic,
udl, etnaviv, virtio, xlnx, panel/boe-bf060y8m-aj0, bridge/synopsis,
panthor, panel/samsung/sofef00m, lontium/lt9611uxc, nouveau, panel/himax-hx8279,
panfrost, st7571-i2c.
- Improve hibmc interrupt handling and add HPD support.
- Add NLT NL13676BC25-03F, Tianma TM070JDHG34-00, Himax HX8279/HX8279-D
DDIC, Visionox G2647FB105, Sitronix ST7571 LCD Controller, panels.
- Add zpos, alpha and blend to renesas.
- Convert drivers to use drm_gem_is_imported, replacing gem->import_attach.
- Support TI AM68 GPU in imagination.
- Support panic handler in virtio.
- Add support to get the panel from DP AUX bus in rockchip and add
RK3588 support.
- Make sofef00 only support the sofef00 panel, not another unrelated
one.
- Add debugfs BO dumping support to panthor, and print associated labels.
- Implement heartbeat based hangcheck in ivpu.
- Mass convert drivers to devm_drm_bridge_alloc api.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://lore.kernel.org/r/e2a958d9-e506-4962-8bae-0dbf2ecc000f@linux.intel.com
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
Driver Changes:
- Eustall locking fix and disabling on VF
- Documentation fix kernel version supporting hwmon entries
- SVM fixes on error handling
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/fqkoqvo62fbkvw6xoxoxutzozqksxxudbmqacjm3durid2pkak@imlxghgrk3ob
|
|
The 'has_dma_mapping' flag should be set once there is a
mapping so it could be unmapped in case of error.
v2:
- Resend for CI
Fixes: 99624bdff867 ("drm/gpusvm: Add support for GPU Shared Virtual Memory")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250428024752.881292-1-matthew.brost@intel.com
(cherry picked from commit f64cf7b681af72d3f715c0d0fd72091a54471c1a)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
The version in the sysfs attribute should correspond to the version in
which this is enabled and visible for end users. It usually doesn't
correspond to the version in which the patch was developed, but rather a
release that will contain it. Update them to 6.15.
Fixes: dac328dea701 ("drm/xe/hwmon: expose package and vram temperature")
Reported-by: Ulisses Furquim <ulisses.furquim@intel.com>
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/4840
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Link: https://lore.kernel.org/r/20250421-hwmon-doc-fix-v1-1-9f68db702249@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 8500393a8e6c58e5e7c135133ad792fc6fd5b6f4)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
On some paths in print_event_fields() it takes the trace_event_sem for
read, even though it should always be held when the function is called.
Remove the taking of that mutex and add a lockdep_assert_held_read() to
make sure the trace_event_sem is held when print_event_fields() is called.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/20250501224128.0b1f0571@batman.local.home
Fixes: 80a76994b2d88 ("tracing: Add "fields" option to show raw trace event fields")
Reported-by: syzbot+441582c1592938fccf09@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/6813ff5e.050a0220.14dd7d.001b.GAE@google.com/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.15-2025-05-01:
amdgpu:
- Fix possible UAF in HDCP
- XGMI dma-buf fix
- NBIO 7.11 fix
- VCN 5.0.1 fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20250501185634.4132187-1-alexander.deucher@amd.com
|
|
This actually reverts 86e92eeeb237 ("bcachefs: Annotate struct bch_xattr
with __counted_by()").
After the x_name, there is a value. According to the disscussion[1],
__counted_by assumes that the flexible array member contains exactly
the amount of elements that are specified. Now there are users came across
a false positive detection of an out of bounds write caused by
the __counted_by here[2], so revert that.
[1] https://lore.kernel.org/lkml/Zv8VDKWN1GzLRT-_@archlinux/T/#m0ce9541c5070146320efd4f928cc1ff8de69e9b2
[2] https://privatebin.net/?a0d4e97d590d71e1#9bLmp2Kb5NU6X6cZEucchDcu88HzUQwHUah8okKPReEt
Signed-off-by: Alan Huang <mmpgouride@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
The original code would skip null delay pointers, but when the pointers
were converted to point within the spi_device struct, the check was not
updated to skip delays of zero. Hence all spi devices that didn't set
delays would fail to probe.
Fixes: 04e6bb0d6bb1 ("spi: modify set_cs_timing parameter")
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Link: https://patch.msgid.link/20250423-spi-tegra114-v1-1-2d608bcc12f9@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The function trace_adjust_address() is used to map addresses of modules
stored in the persistent memory and are also loaded in the current boot to
return the current address for the module.
If there's only one module entry, it will simply use that, otherwise it
performs a bsearch of the entry array to find the modules to offset with.
The issue is if there are no modules in the array. The code does not
account for that and ends up referencing the first element in the array
which does not exist and causes a crash.
If nr_entries is zero, exit out early as if this was a core kernel
address.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/20250501151909.65910359@gandalf.local.home
Fixes: 35a380ddbc653 ("tracing: Show last module text symbols in the stacktrace")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The check for a failed memory location is incorrectly checking
the wrong level of pointer indirection by checking !filter_hash
rather than !*filter_hash. Fix this.
Cc: asami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/20250422221335.89896-1-colin.i.king@gmail.com
Fixes: 0ae6b8ce200d ("ftrace: Fix accounting of subop hashes")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
https://gitlab.freedesktop.org/drm/i915/kernel into drm-fixes
drm/i915 fixes for v6.15-rc5:
- Fix build for CONFIG_DRM_I915_PXP=n
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/87selquhpe.fsf@intel.com
|
|
syzbot reported this bug:
==================================================================
BUG: KASAN: slab-out-of-bounds in trace_seq_to_buffer kernel/trace/trace.c:1830 [inline]
BUG: KASAN: slab-out-of-bounds in tracing_splice_read_pipe+0x6be/0xdd0 kernel/trace/trace.c:6822
Write of size 4507 at addr ffff888032b6b000 by task syz.2.320/7260
CPU: 1 UID: 0 PID: 7260 Comm: syz.2.320 Not tainted 6.15.0-rc1-syzkaller-00301-g3bde70a2c827 #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:408 [inline]
print_report+0xc3/0x670 mm/kasan/report.c:521
kasan_report+0xe0/0x110 mm/kasan/report.c:634
check_region_inline mm/kasan/generic.c:183 [inline]
kasan_check_range+0xef/0x1a0 mm/kasan/generic.c:189
__asan_memcpy+0x3c/0x60 mm/kasan/shadow.c:106
trace_seq_to_buffer kernel/trace/trace.c:1830 [inline]
tracing_splice_read_pipe+0x6be/0xdd0 kernel/trace/trace.c:6822
....
==================================================================
It has been reported that trace_seq_to_buffer() tries to copy more data
than PAGE_SIZE to buf. Therefore, to prevent this, we should use the
smaller of trace_seq_used(&iter->seq) and PAGE_SIZE as an argument.
Link: https://lore.kernel.org/20250422113026.13308-1-aha310510@gmail.com
Reported-by: syzbot+c8cd2d2c412b868263fb@syzkaller.appspotmail.com
Fixes: 3c56819b14b0 ("tracing: splice support for tracing_pipe")
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
00594 ------------[ cut here ]------------
00594 do not call blocking ops when !TASK_RUNNING; state=2 set at [<000000003e51ef4a>] prepare_to_wait_event+0x5c/0x1c0
00594 WARNING: CPU: 12 PID: 1117 at kernel/sched/core.c:8741 __might_sleep+0x74/0x88
00594 Modules linked in:
00594 CPU: 12 UID: 0 PID: 1117 Comm: umount Not tainted 6.15.0-rc4-ktest-g3a72e369412d #21845 PREEMPT
00594 Hardware name: linux,dummy-virt (DT)
00594 pstate: 60001005 (nZCv daif -PAN -UAO -TCO -DIT +SSBS BTYPE=--)
00594 pc : __might_sleep+0x74/0x88
00594 lr : __might_sleep+0x74/0x88
00594 sp : ffffff80c8d67a90
00594 x29: ffffff80c8d67a90 x28: ffffff80f5903500 x27: 0000000000000000
00594 x26: 0000000000000000 x25: ffffff80cf5002a0 x24: ffffffc087dad000
00594 x23: ffffff80c8d67b40 x22: 0000000000000000 x21: 0000000000000000
00594 x20: 0000000000000242 x19: ffffffc080b92020 x18: 00000000ffffffff
00594 x17: 30303c5b20746120 x16: 74657320323d6574 x15: 617473203b474e49
00594 x14: 0000000000000001 x13: 00000000000c0000 x12: ffffff80facc0000
00594 x11: 0000000000000001 x10: 0000000000000001 x9 : ffffffc0800b0774
00594 x8 : c0000000fffbffff x7 : ffffffc087dac670 x6 : 00000000015fffa8
00594 x5 : ffffff80facbffa8 x4 : ffffff80fbd30b90 x3 : 0000000000000000
00594 x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffffff80f5903500
00594 Call trace:
00594 __might_sleep+0x74/0x88 (P)
00594 __mutex_lock+0x64/0x8d8
00594 mutex_lock_nested+0x28/0x38
00594 bch2_fs_ec_flush+0xf8/0x128
00594 __bch2_fs_read_only+0x54/0x1d8
00594 bch2_fs_read_only+0x3e0/0x438
00594 __bch2_fs_stop+0x5c/0x250
00594 bch2_put_super+0x18/0x28
00594 generic_shutdown_super+0x6c/0x140
00594 bch2_kill_sb+0x1c/0x38
00594 deactivate_locked_super+0x54/0xd0
00594 deactivate_super+0x70/0x90
00594 cleanup_mnt+0xec/0x188
00594 __cleanup_mnt+0x18/0x28
00594 task_work_run+0x90/0xd8
00594 do_notify_resume+0x138/0x148
00594 el0_svc+0x9c/0xa0
00594 el0t_64_sync_handler+0x104/0x130
00594 el0t_64_sync+0x154/0x158
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Happy May Day.
Things have calmed down on our end (knock on wood), no outstanding
investigations. Including fixes from Bluetooth and WiFi.
Current release - fix to a fix:
- igc: fix lock order in igc_ptp_reset
Current release - new code bugs:
- Revert "wifi: iwlwifi: make no_160 more generic", fixes regression
to Killer line of devices reported by a number of people
- Revert "wifi: iwlwifi: add support for BE213", initial FW is too
buggy
- number of fixes for mld, the new Intel WiFi subdriver
Previous releases - regressions:
- wifi: mac80211: restore monitor for outgoing frames
- drv: vmxnet3: fix malformed packet sizing in vmxnet3_process_xdp
- eth: bnxt_en: fix timestamping FIFO getting out of sync on reset,
delivering stale timestamps
- use sock_gen_put() in the TCP fraglist GRO heuristic, don't assume
every socket is a full socket
Previous releases - always broken:
- sched: adapt qdiscs for reentrant enqueue cases, fix list
corruptions
- xsk: fix race condition in AF_XDP generic RX path, shared UMEM
can't be protected by a per-socket lock
- eth: mtk-star-emac: fix spinlock recursion issues on rx/tx poll
- btusb: avoid NULL pointer dereference in skb_dequeue()
- dsa: felix: fix broken taprio gate states after clock jump"
* tag 'net-6.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: vertexcom: mse102x: Fix RX error handling
net: vertexcom: mse102x: Add range check for CMD_RTS
net: vertexcom: mse102x: Fix LEN_MASK
net: vertexcom: mse102x: Fix possible stuck of SPI interrupt
net: hns3: defer calling ptp_clock_register()
net: hns3: fixed debugfs tm_qset size
net: hns3: fix an interrupt residual problem
net: hns3: store rx VLAN tag offload state for VF
octeon_ep: Fix host hang issue during device reboot
net: fec: ERR007885 Workaround for conventional TX
net: lan743x: Fix memleak issue when GSO enabled
ptp: ocp: Fix NULL dereference in Adva board SMA sysfs operations
net: use sock_gen_put() when sk_state is TCP_TIME_WAIT
bnxt_en: fix module unload sequence
bnxt_en: Fix ethtool -d byte order for 32-bit values
bnxt_en: Fix out-of-bound memcpy() during ethtool -w
bnxt_en: Fix coredump logic to free allocated buffer
bnxt_en: delay pci_alloc_irq_vectors() in the AER path
bnxt_en: call pci_alloc_irq_vectors() after bnxt_reserve_rings()
bnxt_en: Add missing skb_mark_for_recycle() in bnxt_rx_vlan()
...
|
|
Commit a5951389e58d ("arm64: errata: Add newer ARM cores to the
spectre_bhb_loop_affected() lists") added some additional CPUs to the
Spectre-BHB workaround, including some new arrays for designs that
require new 'k' values for the workaround to be effective.
Unfortunately, the new arrays omitted the sentinel entry and so
is_midr_in_range_list() will walk off the end when it doesn't find a
match. With UBSAN enabled, this leads to a crash during boot when
is_midr_in_range_list() is inlined (which was more common prior to
c8c2647e69be ("arm64: Make _midr_in_range_list() an exported
function")):
| Internal error: aarch64 BRK: 00000000f2000001 [#1] PREEMPT SMP
| pstate: 804000c5 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : spectre_bhb_loop_affected+0x28/0x30
| lr : is_spectre_bhb_affected+0x170/0x190
| [...]
| Call trace:
| spectre_bhb_loop_affected+0x28/0x30
| update_cpu_capabilities+0xc0/0x184
| init_cpu_features+0x188/0x1a4
| cpuinfo_store_boot_cpu+0x4c/0x60
| smp_prepare_boot_cpu+0x38/0x54
| start_kernel+0x8c/0x478
| __primary_switched+0xc8/0xd4
| Code: 6b09011f 54000061 52801080 d65f03c0 (d4200020)
| ---[ end trace 0000000000000000 ]---
| Kernel panic - not syncing: aarch64 BRK: Fatal exception
Add the missing sentinel entries.
Cc: Lee Jones <lee@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: a5951389e58d ("arm64: errata: Add newer ARM cores to the spectre_bhb_loop_affected() lists")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250501104747.28431-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
EU stall sampling is not supported on SRIOV VF. Do not
initialize or open EU stall stream on SRIOV VF.
Fixes: 9a0b11d4cf3b ("drm/xe/eustall: Add support to init, enable and disable EU stall sampling")
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://lore.kernel.org/r/10db5d1c7e17aadca7078ff74575b7ffc0d5d6b8.1745215022.git.harish.chegondi@intel.com
(cherry picked from commit 6ed20625a4b8189a1bd6598aa58e03147ce378ee)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Use a separate lock in the polling function eu_stall_data_buf_poll()
instead of eu_stall->stream_lock. This would prevent a possible
circular locking dependency leading to a deadlock as described below.
This would also require additional locking with the new lock in
the read function.
<4> [787.192986] ======================================================
<4> [787.192988] WARNING: possible circular locking dependency detected
<4> [787.192991] 6.14.0-rc7-xe+ #1 Tainted: G U
<4> [787.192993] ------------------------------------------------------
<4> [787.192994] xe_eu_stall/20093 is trying to acquire lock:
<4> [787.192996] ffff88819847e2c0 ((work_completion)
(&(&stream->buf_poll_work)->work)), at: __flush_work+0x1f8/0x5e0
<4> [787.193005] but task is already holding lock:
<4> [787.193007] ffff88814ce83ba8 (>->eu_stall->stream_lock){3:3},
at: xe_eu_stall_stream_ioctl+0x41/0x6a0 [xe]
<4> [787.193090] which lock already depends on the new lock.
<4> [787.193093] the existing dependency chain (in reverse order) is:
<4> [787.193095]
-> #1 (>->eu_stall->stream_lock){+.+.}-{3:3}:
<4> [787.193099] __mutex_lock+0xb4/0xe40
<4> [787.193104] mutex_lock_nested+0x1b/0x30
<4> [787.193106] eu_stall_data_buf_poll_work_fn+0x44/0x1d0 [xe]
<4> [787.193155] process_one_work+0x21c/0x740
<4> [787.193159] worker_thread+0x1db/0x3c0
<4> [787.193161] kthread+0x10d/0x270
<4> [787.193164] ret_from_fork+0x44/0x70
<4> [787.193168] ret_from_fork_asm+0x1a/0x30
<4> [787.193172]
-> #0 ((work_completion)(&(&stream->buf_poll_work)->work)){+.+.}-{0:0}:
<4> [787.193176] __lock_acquire+0x1637/0x2810
<4> [787.193180] lock_acquire+0xc9/0x300
<4> [787.193183] __flush_work+0x219/0x5e0
<4> [787.193186] cancel_delayed_work_sync+0x87/0x90
<4> [787.193189] xe_eu_stall_disable_locked+0x9a/0x260 [xe]
<4> [787.193237] xe_eu_stall_stream_ioctl+0x5b/0x6a0 [xe]
<4> [787.193285] __x64_sys_ioctl+0xa4/0xe0
<4> [787.193289] x64_sys_call+0x131e/0x2650
<4> [787.193292] do_syscall_64+0x91/0x180
<4> [787.193295] entry_SYSCALL_64_after_hwframe+0x76/0x7e
<4> [787.193299]
other info that might help us debug this:
<4> [787.193302] Possible unsafe locking scenario:
<4> [787.193304] CPU0 CPU1
<4> [787.193305] ---- ----
<4> [787.193306] lock(>->eu_stall->stream_lock);
<4> [787.193308] lock((work_completion)
(&(&stream->buf_poll_work)->work));
<4> [787.193311] lock(>->eu_stall->stream_lock);
<4> [787.193313] lock((work_completion)
(&(&stream->buf_poll_work)->work));
<4> [787.193315]
*** DEADLOCK ***
Fixes: 760edec939685 ("drm/xe/eustall: Add support to read() and poll() EU stall data")
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/4598
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://lore.kernel.org/r/c896932fca84f79db2df5942911997ed77b2b9b6.1744934656.git.harish.chegondi@intel.com
(cherry picked from commit c2b1f1b8641372bb2e563c49eb25632623a860fc)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
bch2_sb_disk_groups_to_cpu() goes off of the superblock member info, so
we need to set that first.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
For vcn5.0.1 only, enable DPG PAUSE to avoid DPG resets.
Signed-off-by: Sonny Jiang <sonny.jiang@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3e5f86c14c3440171f2a3e7a68ceb739297726e9)
|
|
APUs in passthrough mode use HDP flush. 0x7F000 offset used for
remapping HDP flush is mapped to VPE space which could get power gated.
Use another unused offset in BIF space.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d8116a32cdbe456c7f511183eb9ab187e3d590fb)
Cc: stable@vger.kernel.org
|
|
If peer memory is XGMI-accessible, we should never access it through PCIe
P2P DMA mappings. PCIe P2P is slower, has different coherence behaviour,
limited or no support for atomics, or may not work at all. Fail with a
warning if DMABUF mappings of such memory are attempted.
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit dbe4c63689bc6b5fd3ab72650ea4b6a667e96a68)
|
|
The HDCP code in amdgpu_dm_hdcp.c copies pointers to amdgpu_dm_connector
objects without incrementing the kref reference counts. When using a
USB-C dock, and the dock is unplugged, the corresponding
amdgpu_dm_connector objects are freed, creating dangling pointers in the
HDCP code. When the dock is plugged back, the dangling pointers are
dereferenced, resulting in a slab-use-after-free:
[ 66.775837] BUG: KASAN: slab-use-after-free in event_property_validate+0x42f/0x6c0 [amdgpu]
[ 66.776171] Read of size 4 at addr ffff888127804120 by task kworker/0:1/10
[ 66.776179] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.14.0-rc7-00180-g54505f727a38-dirty #233
[ 66.776183] Hardware name: HP HP Pavilion Aero Laptop 13-be0xxx/8916, BIOS F.17 12/18/2024
[ 66.776186] Workqueue: events event_property_validate [amdgpu]
[ 66.776494] Call Trace:
[ 66.776496] <TASK>
[ 66.776497] dump_stack_lvl+0x70/0xa0
[ 66.776504] print_report+0x175/0x555
[ 66.776507] ? __virt_addr_valid+0x243/0x450
[ 66.776510] ? kasan_complete_mode_report_info+0x66/0x1c0
[ 66.776515] kasan_report+0xeb/0x1c0
[ 66.776518] ? event_property_validate+0x42f/0x6c0 [amdgpu]
[ 66.776819] ? event_property_validate+0x42f/0x6c0 [amdgpu]
[ 66.777121] __asan_report_load4_noabort+0x14/0x20
[ 66.777124] event_property_validate+0x42f/0x6c0 [amdgpu]
[ 66.777342] ? __lock_acquire+0x6b40/0x6b40
[ 66.777347] ? enable_assr+0x250/0x250 [amdgpu]
[ 66.777571] process_one_work+0x86b/0x1510
[ 66.777575] ? pwq_dec_nr_in_flight+0xcf0/0xcf0
[ 66.777578] ? assign_work+0x16b/0x280
[ 66.777580] ? lock_is_held_type+0xa3/0x130
[ 66.777583] worker_thread+0x5c0/0xfa0
[ 66.777587] ? process_one_work+0x1510/0x1510
[ 66.777588] kthread+0x3a2/0x840
[ 66.777591] ? kthread_is_per_cpu+0xd0/0xd0
[ 66.777594] ? trace_hardirqs_on+0x4f/0x60
[ 66.777597] ? _raw_spin_unlock_irq+0x27/0x60
[ 66.777599] ? calculate_sigpending+0x77/0xa0
[ 66.777602] ? kthread_is_per_cpu+0xd0/0xd0
[ 66.777605] ret_from_fork+0x40/0x90
[ 66.777607] ? kthread_is_per_cpu+0xd0/0xd0
[ 66.777609] ret_from_fork_asm+0x11/0x20
[ 66.777614] </TASK>
[ 66.777643] Allocated by task 10:
[ 66.777646] kasan_save_stack+0x39/0x60
[ 66.777649] kasan_save_track+0x14/0x40
[ 66.777652] kasan_save_alloc_info+0x37/0x50
[ 66.777655] __kasan_kmalloc+0xbb/0xc0
[ 66.777658] __kmalloc_cache_noprof+0x1c8/0x4b0
[ 66.777661] dm_dp_add_mst_connector+0xdd/0x5c0 [amdgpu]
[ 66.777880] drm_dp_mst_port_add_connector+0x47e/0x770 [drm_display_helper]
[ 66.777892] drm_dp_send_link_address+0x1554/0x2bf0 [drm_display_helper]
[ 66.777901] drm_dp_check_and_send_link_address+0x187/0x1f0 [drm_display_helper]
[ 66.777909] drm_dp_mst_link_probe_work+0x2b8/0x410 [drm_display_helper]
[ 66.777917] process_one_work+0x86b/0x1510
[ 66.777919] worker_thread+0x5c0/0xfa0
[ 66.777922] kthread+0x3a2/0x840
[ 66.777925] ret_from_fork+0x40/0x90
[ 66.777927] ret_from_fork_asm+0x11/0x20
[ 66.777932] Freed by task 1713:
[ 66.777935] kasan_save_stack+0x39/0x60
[ 66.777938] kasan_save_track+0x14/0x40
[ 66.777940] kasan_save_free_info+0x3b/0x60
[ 66.777944] __kasan_slab_free+0x52/0x70
[ 66.777946] kfree+0x13f/0x4b0
[ 66.777949] dm_dp_mst_connector_destroy+0xfa/0x150 [amdgpu]
[ 66.778179] drm_connector_free+0x7d/0xb0
[ 66.778184] drm_mode_object_put.part.0+0xee/0x160
[ 66.778188] drm_mode_object_put+0x37/0x50
[ 66.778191] drm_atomic_state_default_clear+0x220/0xd60
[ 66.778194] __drm_atomic_state_free+0x16e/0x2a0
[ 66.778197] drm_mode_atomic_ioctl+0x15ed/0x2ba0
[ 66.778200] drm_ioctl_kernel+0x17a/0x310
[ 66.778203] drm_ioctl+0x584/0xd10
[ 66.778206] amdgpu_drm_ioctl+0xd2/0x1c0 [amdgpu]
[ 66.778375] __x64_sys_ioctl+0x139/0x1a0
[ 66.778378] x64_sys_call+0xee7/0xfb0
[ 66.778381] do_syscall_64+0x87/0x140
[ 66.778385] entry_SYSCALL_64_after_hwframe+0x4b/0x53
Fix this by properly incrementing and decrementing the reference counts
when making and deleting copies of the amdgpu_dm_connector pointers.
(Mario: rebase on current code and update fixes tag)
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4006
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Fixes: da3fd7ac0bcf3 ("drm/amd/display: Update CP property based on HW query")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250417215005.37964-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d4673f3c3b3dcb74e36e53cdfc880baa7a87b330)
Cc: stable@vger.kernel.org
|
|
Stefan Wahren says:
====================
net: vertexcom: mse102x: Fix RX handling
This series is the first part of two series for the Vertexcom driver.
It contains substantial fixes for the RX handling of the Vertexcom MSE102x.
====================
Link: https://patch.msgid.link/20250430133043.7722-1-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case the CMD_RTS got corrupted by interferences, the MSE102x
doesn't allow a retransmission of the command. Instead the Ethernet
frame must be shifted out of the SPI FIFO. Since the actual length is
unknown, assume the maximum possible value.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-5-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since there is no protection in the SPI protocol against electrical
interferences, the driver shouldn't blindly trust the length payload
of CMD_RTS. So introduce a bounds check for incoming frames.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-4-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The LEN_MASK for CMD_RTS doesn't cover the whole parameter mask.
The Bit 11 is reserved, so adjust LEN_MASK accordingly.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MSE102x doesn't provide any SPI commands for interrupt handling.
So in case the interrupt fired before the driver requests the IRQ,
the interrupt will never fire again. In order to fix this always poll
for pending packets after opening the interface.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jijie Shao says:
====================
There are some bugfix for the HNS3 ethernet driver
====================
Link: https://patch.msgid.link/20250430093052.2400464-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the ptp_clock_register() is called before relative
ptp resource ready. It may cause unexpected result when upper
layer called the ptp API during the timewindow. Fix it by
moving the ptp_clock_register() to the function end.
Fixes: 0bf5eb788512 ("net: hns3: add support for PTP")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250430093052.2400464-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The size of the tm_qset file of debugfs is limited to 64 KB,
which is too small in the scenario with 1280 qsets.
The size needs to be expanded to 1 MB.
Fixes: 5e69ea7ee2a6 ("net: hns3: refactor the debugfs process")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250430093052.2400464-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a VF is passthrough to a VM, and the VM is killed, the reported
interrupt may not been handled, it will remain, and won't be clear by
the nic engine even with a flr or tqp reset. When the VM restart, the
interrupt of the first vector may be dropped by the second enable_irq
in vfio, see the issue below:
https://gitlab.com/qemu-project/qemu/-/issues/2884#note_2423361621
We notice that the vfio has always behaved this way, and the interrupt
is a residue of the nic engine, so we fix the problem by moving the
vector enable process out of the enable_irq loop.
Fixes: 08a100689d4b ("net: hns3: re-organize vector handle")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250430093052.2400464-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VF driver missed to store the rx VLAN tag strip state when
user change the rx VLAN tag offload state. And it will default
to enable the rx vlan tag strip when re-init VF device after
reset. So if user disable rx VLAN tag offload, and trig reset,
then the HW will still strip the VLAN tag from packet nad fill
into RX BD, but the VF driver will ignore it for rx VLAN tag
offload disabled. It may cause the rx VLAN tag dropped.
Fixes: b2641e2ad456 ("net: hns3: Add support of hardware rx-vlan-offload to HNS3 VF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250430093052.2400464-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-04-29 (idpf, igc)
For idpf:
Michal fixes error path handling to remove memory leak.
Larysa prevents reset from being called during shutdown.
For igc:
Jake adjusts locking order to resolve sleeping in atomic context.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: fix lock order in igc_ptp_reset
idpf: protect shutdown from reset
idpf: fix potential memory leak on kcalloc() failure
====================
Link: https://patch.msgid.link/20250429221034.3909139-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the host loses heartbeat messages from the device,
the driver calls the device-specific ndo_stop function,
which frees the resources. If the driver is unloaded in
this scenario, it calls ndo_stop again, attempting to free
resources that have already been freed, leading to a host
hang issue. To resolve this, dev_close should be called
instead of the device-specific stop function.dev_close
internally calls ndo_stop to stop the network interface
and performs additional cleanup tasks. During the driver
unload process, if the device is already down, ndo_stop
is not called.
Fixes: 5cb96c29aa0e ("octeon_ep: add heartbeat monitor")
Signed-off-by: Sathesh B Edara <sedara@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250429114624.19104-1-sedara@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Activate TX hang workaround also in
fec_enet_txq_submit_skb() when TSO is not enabled.
Errata: ERR007885
Symptoms: NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
commit 37d6017b84f7 ("net: fec: Workaround for imx6sx enet tx hang when enable three queues")
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
Fixes: 53bb20d1faba ("net: fec: add variable reg_desc_active to speed things up")
Signed-off-by: Mattias Barthel <mattias.barthel@atlascopco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250429090826.3101258-1-mattiasbarthel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Always map the `skb` to the LS descriptor. Previously skb was
mapped to EXT descriptor when the number of fragments is zero with
GSO enabled. Mapping the skb to EXT descriptor prevents it from
being freed, leading to a memory leak
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250429052527.10031-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On Adva boards, SMA sysfs store/get operations can call
__handle_signal_outputs() or __handle_signal_inputs() while the `irig`
and `dcf` pointers are uninitialized, leading to a NULL pointer
dereference in __handle_signal() and causing a kernel crash. Adva boards
don't use `irig` or `dcf` functionality, so add Adva-specific callbacks
`ptp_ocp_sma_adva_set_outputs()` and `ptp_ocp_sma_adva_set_inputs()` that
avoid invoking `irig` or `dcf` input/output routines.
Fixes: ef61f5528fca ("ptp: ocp: add Adva timecard support")
Signed-off-by: Sagi Maimon <maimon.sagi@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250429073320.33277-1-maimon.sagi@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is possible for a pointer of type struct inet_timewait_sock to be
returned from the functions __inet_lookup_established() and
__inet6_lookup_established(). This can cause a crash when the
returned pointer is of type struct inet_timewait_sock and
sock_put() is called on it. The following is a crash call stack that
shows sk->sk_wmem_alloc being accessed in sk_free() during the call to
sock_put() on a struct inet_timewait_sock pointer. To avoid this issue,
use sock_gen_put() instead of sock_put() when sk->sk_state
is TCP_TIME_WAIT.
mrdump.ko ipanic() + 120
vmlinux notifier_call_chain(nr_to_call=-1, nr_calls=0) + 132
vmlinux atomic_notifier_call_chain(val=0) + 56
vmlinux panic() + 344
vmlinux add_taint() + 164
vmlinux end_report() + 136
vmlinux kasan_report(size=0) + 236
vmlinux report_tag_fault() + 16
vmlinux do_tag_recovery() + 16
vmlinux __do_kernel_fault() + 88
vmlinux do_bad_area() + 28
vmlinux do_tag_check_fault() + 60
vmlinux do_mem_abort() + 80
vmlinux el1_abort() + 56
vmlinux el1h_64_sync_handler() + 124
vmlinux > 0xFFFFFFC080011294()
vmlinux __lse_atomic_fetch_add_release(v=0xF2FFFF82A896087C)
vmlinux __lse_atomic_fetch_sub_release(v=0xF2FFFF82A896087C)
vmlinux arch_atomic_fetch_sub_release(i=1, v=0xF2FFFF82A896087C)
+ 8
vmlinux raw_atomic_fetch_sub_release(i=1, v=0xF2FFFF82A896087C)
+ 8
vmlinux atomic_fetch_sub_release(i=1, v=0xF2FFFF82A896087C) + 8
vmlinux __refcount_sub_and_test(i=1, r=0xF2FFFF82A896087C,
oldp=0) + 8
vmlinux __refcount_dec_and_test(r=0xF2FFFF82A896087C, oldp=0) + 8
vmlinux refcount_dec_and_test(r=0xF2FFFF82A896087C) + 8
vmlinux sk_free(sk=0xF2FFFF82A8960700) + 28
vmlinux sock_put() + 48
vmlinux tcp6_check_fraglist_gro() + 236
vmlinux tcp6_gro_receive() + 624
vmlinux ipv6_gro_receive() + 912
vmlinux dev_gro_receive() + 1116
vmlinux napi_gro_receive() + 196
ccmni.ko ccmni_rx_callback() + 208
ccmni.ko ccmni_queue_recv_skb() + 388
ccci_dpmaif.ko dpmaif_rxq_push_thread() + 1088
vmlinux kthread() + 268
vmlinux 0xFFFFFFC08001F30C()
Fixes: c9d1d23e5239 ("net: add heuristic for enabling TCP fraglist GRO")
Signed-off-by: Jibin Zhang <jibin.zhang@mediatek.com>
Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250429020412.14163-1-shiming.cheng@mediatek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
