| Age | Commit message (Collapse) | Author |
|---|
|
The AK4118A is a digital audio transceiver supporting 8 input channels
at 192kHz and with 24bits resolution.
It converts the S/PDIF signal to I2S format and is configurable over I2C.
This driver introduce a minimal support of the AK4118, like selecting the
input channel, reading input frequency and detecting some errors.
Datasheet is available here:
https://www.akm.com/akm/en/file/datasheet/AK4118AEQ.pdf
Signed-off-by: Adrien Charruel <adrien.charruel@devialet.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document the bindings for AK4118 S/PDIF transceiver
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to the current device datasheet (TI Lit # SLAS831D, revised
March 2018) the value written to the device's PAGE register to trigger
a complete register reset should be 0xfe, not 0xff. So go ahead and
update to the correct value.
Reported-by: Stephane Le Provost <stephane.leprovost@mediatek.com>
Tested-by: Stephane Le Provost <stephane.leprovost@mediatek.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
sound/soc/amd/raven/acp3x-pcm-dma.c: In function 'acp3x_dma_hw_params':
sound/soc/amd/raven/acp3x-pcm-dma.c:333:25: warning:
variable 'dma_buffer' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
8de1b5ed0337 ("ASoC: amd: add acp3x system resume pm op")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Adopt the SPDX license identifier headers to ease license
compliance management.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixed build errors.
- Implicit declaration of pci_enable_msi() & pci_disable_msi()
api's for openrisc architecture.
- type defaults to 'int' in declaration of 'module_pci_driver'
Enabled build for x86 architecture.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch fixes typo in the comment.
Signed-off-by: David Lin <CTLIN0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch updates license to SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: David Lin <CTLIN0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Audio map are possible in wrong state before card->instantiated has
been set to true. Imaging the following examples:
time 1: at the beginning
in:-1 in:-1 in:-1 in:-1
out:-1 out:-1 out:-1 out:-1
SIGGEN A B Spk
time 2: after someone called snd_soc_dapm_new_widgets()
(e.g. create_fill_widget_route_map() in sound/soc/codecs/hdac_hdmi.c)
in:1 in:0 in:0 in:0
out:0 out:0 out:0 out:1
SIGGEN A B Spk
time 3: routes added
in:1 in:0 in:0 in:0
out:0 out:0 out:0 out:1
SIGGEN -----> A -----> B ---> Spk
In the end, the path should be powered on but it did not. At time 3,
"in" of SIGGEN and "out" of Spk did not propagate to their neighbors
because snd_soc_dapm_add_path() will not invalidate the paths if
the card has not instantiated (i.e. card->instantiated is false).
To correct the state of audio map, recalculate the whole map forcely.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The machine driver fails to probe in next-20181113 with:
[ 2.539093] omap-abe-twl6040 sound: ASoC: CODEC DAI twl6040-legacy not registered
[ 2.546630] omap-abe-twl6040 sound: devm_snd_soc_register_card() failed: -517
...
[ 3.693206] omap-abe-twl6040 sound: ASoC: Both platform name/of_node are set for TWL6040
[ 3.701446] omap-abe-twl6040 sound: ASoC: failed to init link TWL6040
[ 3.708007] omap-abe-twl6040 sound: devm_snd_soc_register_card() failed: -22
[ 3.715148] omap-abe-twl6040: probe of sound failed with error -22
Bisect pointed to a merge commit:
first bad commit: [0f688ab20a540aafa984c5dbd68a71debebf4d7f] Merge remote-tracking branch 'net-next/master'
and a diff between a working kernel does not reveal anything which would
explain the change in behavior.
Further investigation showed that on the second try of loading fails
because the dai_link->platform is no longer NULL and it might be pointing
to uninitialized memory.
The fix is to move the snd_soc_dai_link and snd_soc_card inside of the
abe_twl6040 struct, which is dynamically allocated every time the driver
probes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently when snd_pcm_hw_constraint_integer fails there is
a memory leak of i2s_data on the error return path. Fix this by
kfree'ing i2s_data before returning.
Detected by CoverityScan, CID#1475479 ("Resource leak")
Fixes: 0b87d6bcd648 ("ASoC: amd: add acp3x pcm driver dma ops")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DAC output may be differential (default) or single-ended.
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the initial commit [1], I added differential output of the codec as
separate `+` and `-` widgets:
OUTL+
OUTR+
OUTL-
OUTR-
Later, in the commit [2], I added a device tree property to configure the
output as single-ended or differential. Having this property, the `+` and
`-` separation in widgets seems for me confusing. There are no functional
benefits in such separation, so I find reasonable to get rid of it:
OUTL
OUTR
The new naming is more friendly for sound cards, and is better aligned with
other codec drivers in kernel.
Renaming the output widgets now should not be a problem from the backwards-
compatibility perspective, as the driver for PCM3060 is added into the
mainline very recently, and did not yet appear in any releases.
[1] commit 6ee47d4a8dac ("ASoC: pcm3060: Add codec driver")
[2] commit a78c62de00d5 ("ASoC: pcm3060: Add DT property for single-ended
output")
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Fixes: 8307b2afd386 ("ASoC: stm32: sai: set sai as mclk clock provider")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Frontend dai_link id is used for closing ADM sessions.
During concurrent usecase when one session is closed,
it closes other ADM session associated with other usecase
too. Dai_link->id should always point to Frontend dai id.
Set cpu_dai id as dai_link id to fix the issue.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sun8i-codec misses a route from ADC to AIF1 Slot 0 ADC. Add it
to the driver to avoid adding it to every dts.
Fixes: eda85d1fee05d ("ASoC: sun8i-codec: Add ADC support for a33")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ACP3x drivers can be built by selecting necessary kernel config option.
The patch enables build support of the same.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When system wide suspend happens, ACP will be powered off.
When system resumes, all the runtime configuration data for
ACP needs to be programmed again.
Added 'resume'pm call back to ACP pm ops.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Added runtime PM operations for ACP3x PCM platform device.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ACP3x I2S (CPU DAI) can act in normal I2S and TDM modes.
Added support for TDM mode.
Desired mode can be selected from ASoC machine driver.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ACP3x has a i2s controller block for playback and capture.
This patch adds ACP3x i2s DAI operations.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ACP3x has a DMA controller to access system memory.
This controller transfers data from/to system memory
to/from the ACP internal FIFO.
The patch adds PCM driver DMA operations.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Whenever audio data equal to the I2S FIFO watermark level are
produced/consumed, interrupt is generated.
Acknowledge the interrupt.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
PCM platform driver binds to the platform device created by ACP3x PCI
device. PCM driver registers ALSA DMA and CPU DAI components with ASoC
framework.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ACP 3x IP has I2S controller device as one of IP blocks.
Create a platform device for it, so that the PCM platform driver
can be bound to this device. Pass PCI resources like MMIO, irq
to the platform device.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <vishnuvardhanrao.ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ACP 3.0 is a PCI audio device. This patch adds PCI driver to bind
to this device and get PCI resources.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Signed-off-by: Sanju R Mehta <sanju.mehta@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ACP 3.x is a new audio block in raven. Added register header
of the same.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On certain platforms, Display HDMI HDA codec was not going to sleep state
after the use when links are powered down after turning off the display
power. As per the HW recommendation, links are powered down before turning
off the display power to ensure that the codec goes to sleep state.
This patch was updated from an earlier version submitted upstream [1]
which conflicted with the changes merged for HDaudio codec support
with the Intel DSP.
[1] https://patchwork.kernel.org/patch/10540213/
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add Icelake device id. Also, Icelake's pin2port mapping table is
complicated. So we use a mapping table to do the pin2port mapping.
Signed-off-by: Bard liao <bard.liao@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Factor out the duplicated initialization statements from
wm_adsp1_init() and wm_adsp2_init() into new function
wm_adsp_common_init().
The entire content of wm_adsp1_init() is the common code
but it is convenient to retain this exported function
to hide what we currently treat as common init (which might
change in the future) and also make clear the difference
between an ADSP1 entry point and common code.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Stack memory isn't DMA-safe so it isn't safe to use either
regmap_raw_read or regmap_bulk_read to read into stack memory.
The two functions to read the scratch registers were using
stack memory and regmap_raw_read. It's not worth allocating
memory just for this trivial read, and it isn't time-critical.
A simple regmap_read for each register is sufficient.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds missing prepare_sleve_config that is needed for
setup the DMA slave channel for I2S.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Initializing to -EINVAL is not correct as the variables are unsigned and
if buffer_size is 0 then they are not used anyway.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver will not probe if the pdata is not provided or created.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The mcbsp.c was copied a while back from arch/arm/plat-omap/mcbsp.c and it
contained a mix of McBSP and McBSP sidetone functions.
Create new file structure with the following split:
omap-mcbsp.c - McBSP related functions
omap-mcbsp-st.c - McBSP sidetone functionality
omap-mcbsp-priv.h - Private header for internal use
omap-mcbsp.h - Header for user drivers
I have tried to do the code move with minimal code change, cleanup patches
can be based on the new structure.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Check if the McBSP have FIFO in the omap_mcbsp_set_threshold() and
omap_mcbsp_dai_delay() delay function to skip calling the lower layer if
it is not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We either start/stop TX or RX, never both. Move the tx/rx direction
selection within the functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The parameter name of dev_id is leftover from the old times when we passed
numeric ID as data for the interrupt handlers.
The mcbsp_rx and mcbsp_tx is misleading as they are pointers to the mcbsp
struct.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is configured runtime so no need to initialize it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make the omap_mcbsp_dma_reg_params() a bit more intuitive to read for the
first glance by using SNDRV_PCM_STREAM_PLAYBACK/CAPTURE and to group the
outermost if case by stream direction.
While there, fix the outdated comment for the function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
commit c0ea089dbad4 ("ASoC: rsnd: rsnd_mod_name() handles both name and
ID") merged "name" and "ID" on rsnd_mod_name() to handle sub-ID
(= for CTU/BUSIF).
Then, it decided to share static char to avoid pointless memory.
But, it doesn't work correctry in below case, because last called
name will be used.
dev_xxx(dev, "%s is connected to %s\n",
rsnd_mod_name(mod_a), /* ssiu[00] */
rsnd_mod_name(mod_b)); /* ssi[0] */
->
rcar_sound ec500000.sound: ssi[0] is connected to ssi[0]
~~~~~~ ~~~~~~
We still don't want to have pointless memory, so let's use ring buffer.
16byte x 5 is very enough for this purpose.
dev_xxx(dev, "%s is connected to %s\n",
rsnd_mod_name(mod_a), /* ssiu[00] */
rsnd_mod_name(mod_b)); /* ssi[0] */
->
rcar_sound ec500000.sound: ssiu[00] is connected to ssi[0]
~~~~~~~~ ~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
drvdata is actually sun8i_codec, not snd_soc_card, so it crashes
when calling snd_soc_card_get_drvdata().
Drop card and scodec vars anyway since we don't need to
disable/unprepare clocks - it's already done by calling
runtime_suspend()
Drop clk_disable_unprepare() calls for the same reason.
Fixes: 36c684936fae7 ("ASoC: Add sun8i digital audio codec")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds TDM Split mode support. rsnd driver is assuming
audio-graph-scu-card is used for Sound Card.
This is very simple sample DT settings to use it.
sound_card: sound {
compatible = "audio-graph-scu-card";
...
convert-channels = <8>; /* TDM Split */
dais = <&rsnd_port0 /* playback ch1/ch2 */
&rsnd_port1 /* playback ch3/ch4 */
&rsnd_port2 /* playback ch5/ch6 */
&rsnd_port3 /* playback ch7/ch8 */
>;
};
audio-codec {
...
port {
codec_0: endpoint@1 {
remote-endpoint = <&rsnd_ep0>;
};
codec_1: endpoint@2 {
remote-endpoint = <&rsnd_ep1>;
};
codec_2: endpoint@3 {
remote-endpoint = <&rsnd_ep2>;
};
codec_3: endpoint@4 {
remote-endpoint = <&rsnd_ep3>;
};
};
};
&rcar_sound {
...
ports {
rsnd_port0: port@0 {
rsnd_ep0: endpoint {
remote-endpoint = <&codec_0>;
...
playback = <&ssiu30 &ssi3>;
};
};
rsnd_port1: port@1 {
rsnd_ep1: endpoint {
remote-endpoint = <&codec_1>;
...
playback = <&ssiu31 &ssi3>;
};
};
rsnd_port2: port@2 {
rsnd_ep2: endpoint {
remote-endpoint = <&codec_2>;
...
playback = <&ssiu32 &ssi3>;
};
};
rsnd_port3: port@3 {
rsnd_ep3: endpoint {
remote-endpoint = <&codec_3>;
...
playback = <&ssiu33 &ssi3>;
};
};
};
};
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds TDM Split mode support. rsnd driver is assuming
audio-graph-scu-card is used for Sound Card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Gen2 has BUSIF0-3, Gen3 has BUSIF0-7 on some SSIU.
Current driver is assuming it is using BUSIF0 as default.
Thus, SSI is attaching SSIU (with BUSIF0) by using rsnd_ssiu_attach().
But, TDM split mode also needs other BUSIF to use it.
This patch adds missing SSIU BUSIFx support.
BUSIF is handled by SSIU instead of SSI anymore.
Thus, its settings no longer needed on SSI node on DT.
This patch removes its settings from Document, but driver is still
keeping compatibility. Thus, old DT style is still working.
But, to avoid confusing, it doesn't indicate old compatibility things on
Document. New SoC should have SSIU on DT from this patch.
1) old style DT is still supported (= no rcar_sound,ssiu node on DT)
2) If ssiu is not indicated on playback/capture,
BUSIF0 will be used as default
playback = <&ssi3>; /* ssiu30 will be selected */
3) you can select own ssiu
playback = <&ssi32 &ssi3>; /* ssiu32 will be selected */
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Gen2 has BUSIF0-3, Gen3 has BUSIF0-7 on some SSIU.
Current driver is assuming it is using BUSIF0 as default.
Thus, SSI is attaching SSIU (with BUSIF0) by using rsnd_ssiu_attach().
But, TDM split mode also needs other BUSIF to use it.
This patch adds missing SSIU BUSIFx support.
BUSIF is handled by SSIU instead of SSI anymore.
Thus, its settings no longer needed on SSI node on DT.
This patch removes its settings from Document, but driver is still
keeping compatibility. Thus, old DT style is still working.
But, to avoid confusing, it doesn't indicate old compatibility things on
Document. New SoC should have SSIU on DT from this patch.
1) old style DT is still supported (= no rcar_sound,ssiu node on DT)
2) If ssiu is not indicated on playback/capture,
BUSIF0 will be used as default
playback = <&ssi3>; /* ssiu30 will be selected */
3) you can select own ssiu
playback = <&ssi32 &ssi3>; /* ssiu32 will be selected */
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It has duplicated DT example code on Document.
This patch tidyup these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
converted rate/chan are handled each rated module, but
it will be used other module too.
For examle, converted channel is currently used for CTU,
but, it will be used for TDM Split mode, too.
This patch move/merge SRC/CTU hw_param under core.c
and handles converted rate/chan under rsnd_dai_stream.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current driver is supporting HDMI output, and its information
are handled under ssi.c. But, it is stream information.
Let's move it from ssi.c to core.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
