| Age | Commit message (Collapse) | Author |
|---|
|
We found the I2C controller count register is unreliable sometimes,
that will cause I2C to lose data. Thus we can read the data count
from 'i2c_dev->count' instead of the I2C controller count register.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add one flag to indicate if the i2c controller has been in suspend state,
which can prevent i2c accesses after i2c controller is suspended following
system suspend.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
i2cdev_ioctl_rdwr() allocates i2c_msg.buf using memdup_user(), which
returns ZERO_SIZE_PTR if i2c_msg.len is zero.
Currently i2cdev_ioctl_rdwr() always dereferences the buf pointer in case
of I2C_M_RD | I2C_M_RECV_LEN transfer. That causes a kernel oops in
case of zero len.
Let's check the len against zero before dereferencing buf pointer.
This issue was triggered by syzkaller.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[wsa: use '< 1' instead of '!' for easier readability]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Our out-of-line atomics are built with a special calling convention,
preventing pointless stack spilling, and allowing us to patch call sites
with ARMv8.1 atomic instructions.
Instrumentation inserted by the compiler may result in calls to
functions not following this special calling convention, resulting in
registers being unexpectedly clobbered, and various problems resulting
from this.
For example, if a kernel is built with KCOV and ARM64_LSE_ATOMICS, the
compiler inserts calls to __sanitizer_cov_trace_pc in the prologues of
the atomic functions. This has been observed to result in spurious
cmpxchg failures, leading to a hang early on in the boot process.
This patch avoids such issues by preventing instrumentation of our
out-of-line atomics.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
As the Geminilake firmware is now merged to linux-firmware.git
use MODUE_FIRMWARE to load the firmware.
This removes the error message in the dmesg log:
i915 0000:00:02.0: Direct firmware load for
i915/glk_dmc_ver1_04.bin failed with error -2
i915 0000:00:02.0: Failed to load DMC firmware
i915/glk_dmc_ver1_04.bin. Disabling runtime power management.
i915 0000:00:02.0: DMC firmware homepage:
https://01.org/linuxgraphics/downloads/firmware
and now shows that the firmware has correctly loaded:
[drm] Finished loading DMC firmware i915/glk_dmc_ver1_04.bin (v1.4)
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180411044213.383-1-ianwmorrison@gmail.com
|
|
https://github.com/Broadcom/stblinux into fixes
Pull "Broadcom devicetree-arm64 fixes for 4.17" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes
for 4.17, please pull the following:
- Srinath fixes the register base address of all SATA controllers on
Stingray
* tag 'arm-soc/for-4.17/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux:
arm64: dts: correct SATA addresses for Stingray
|
|
Add missing "altivec unavailable" interrupt injection helper
thus fixing the linker error below:
arch/powerpc/kvm/emulate_loadstore.o: In function `kvmppc_check_altivec_disabled':
arch/powerpc/kvm/emulate_loadstore.c: undefined reference to `.kvmppc_core_queue_vec_unavail'
Fixes: 09f984961c137c4b ("KVM: PPC: Book3S: Add MMIO emulation for VMX instructions")
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
smp_send_stop can lock up the IPI path for any subsequent calls,
because the receiving CPUs spin in their handler function. This
started becoming a problem with the addition of an smp_send_stop
call in the reboot path, because panics can reboot after doing
their own smp_send_stop.
The NMI IPI variant was fixed with ac61c11566 ("powerpc: Fix
smp_send_stop NMI IPI handling"), which leaves the smp_call_function
variant.
This is fixed by having smp_send_stop only ever do the
smp_call_function once. This is a bit less robust than the NMI IPI
fix, because any other call to smp_call_function after smp_send_stop
could deadlock, but that has always been the case, and it was not
been a problem before.
Fixes: f2748bdfe1573 ("powerpc/powernv: Always stop secondaries before reboot/shutdown")
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
gpstate_timer_handler() uses synchronous smp_call to set the pstate
on the requested core. This causes the below hard lockup:
smp_call_function_single+0x110/0x180 (unreliable)
smp_call_function_any+0x180/0x250
gpstate_timer_handler+0x1e8/0x580
call_timer_fn+0x50/0x1c0
expire_timers+0x138/0x1f0
run_timer_softirq+0x1e8/0x270
__do_softirq+0x158/0x3e4
irq_exit+0xe8/0x120
timer_interrupt+0x9c/0xe0
decrementer_common+0x114/0x120
-- interrupt: 901 at doorbell_global_ipi+0x34/0x50
LR = arch_send_call_function_ipi_mask+0x120/0x130
arch_send_call_function_ipi_mask+0x4c/0x130
smp_call_function_many+0x340/0x450
pmdp_invalidate+0x98/0xe0
change_huge_pmd+0xe0/0x270
change_protection_range+0xb88/0xe40
mprotect_fixup+0x140/0x340
SyS_mprotect+0x1b4/0x350
system_call+0x58/0x6c
One way to avoid this is removing the smp-call. We can ensure that the
timer always runs on one of the policy-cpus. If the timer gets
migrated to a cpu outside the policy then re-queue it back on the
policy->cpus. This way we can get rid of the smp-call which was being
used to set the pstate on the policy->cpus.
Fixes: 7bc54b652f13 ("timers, cpufreq/powernv: Initialize the gpstate timer as pinned")
Cc: stable@vger.kernel.org # v4.8+
Reported-by: Nicholas Piggin <npiggin@gmail.com>
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix for black screen issues (FDO #104158 and #104425)
- A correction for wrongly applied display W/A
- Fixes for HDA codec interop issue (no audio) and too eager HW timeouts
* tag 'drm-intel-fixes-2018-04-26' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915/fbdev: Enable late fbdev initial configuration
drm/i915: Use ktime on wait_for
drm/i915: Enable display WA#1183 from its correct spot
drm/i915/audio: set minimum CD clock to twice the BCLK
|
|
Pull virtio fixups from Michael Tsirkin:
- Latest header update will break QEMU (if it's rebuilt with the new
header) - and it seems that the code there is so fragile that any
change in this header will break it. Add a better interface so users
do not need to change their code every time that header changes.
- Fix virtio console for spec compliance.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_console: reset on out of memory
virtio_console: move removal code
virtio_console: drop custom control queue cleanup
virtio_console: free buffers after reset
virtio: add ability to iterate over vqs
virtio_console: don't tie bufs to a vq
virtio_balloon: add array of stat names
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Add support for new Ryzen chips to k10temp driver
... making Phoronix happy
- Fix inconsistent chip access in nct6683 driver
- Handle absence of few types of sensors in scmi driver
* tag 'hwmon-for-linus-v4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (k10temp) Add support for AMD Ryzen w/ Vega graphics
hwmon: (k10temp) Add temperature offset for Ryzen 2700X
hwmon: (nct6683) Enable EC access if disabled at boot
hwmon: (scmi) handle absence of few types of sensors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix Aardvark MRRS setting (Evan Wang)
- clarify "bandwidth available" link status message (Jakub Kicinski)
- update Kirin GPIO name to fix probe failure (Loic Poulain)
- fix Aardvark IRQ usage (Victor Gu)
- fix Aardvark config accessor issues (Victor Gu)
* tag 'pci-v4.17-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Add "PCIe" to pcie_print_link_status() messages
PCI: kirin: Fix reset gpio name
PCI: aardvark: Fix PCIe Max Read Request Size setting
PCI: aardvark: Use ISR1 instead of ISR0 interrupt in legacy irq mode
PCI: aardvark: Set PIO_ADDR_LS correctly in advk_pcie_rd_conf()
PCI: aardvark: Fix logic in advk_pcie_{rd,wr}_conf()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Add workqueue forward declaration (for new work, but a nice clean up)
- seftest fixes for the new histogram code
- Print output fix for hwlat tracer
- Fix missing system call events - due to change in x86 syscall naming
- Fix kprobe address being used by perf being hashed
* tag 'trace-v4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix missing tab for hwlat_detector print format
selftests: ftrace: Add a testcase for multiple actions on trigger
selftests: ftrace: Fix trigger extended error testcase
kprobes: Fix random address output of blacklist file
tracing: Fix kernel crash while using empty filter with perf
tracing/x86: Update syscall trace events to handle new prefixed syscall func names
tracing: Add missing forward declaration
|
|
This was my bad, spec says that the name of this bit is
'Y-coordinate valid' but the values for it is:
0: Include Y-coordinate valid eDP1.4a
1: Do not include Y-coordinate valid eDP 1.4
So not setting it.
BSpec: 7713
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180425212334.21109-4-jose.souza@intel.com
|
|
IGT tests could be improved with sink status, knowing for sure that
hardware have activate or exit PSR.
v3:
Reading i915_edp_psr_status was causing PSR to exit but now with
'drm/i915/psr: Prevent PSR exit when a non-pipe related register is
written' it is fixed.
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180425212334.21109-3-jose.souza@intel.com
|
|
This will be helpful to debug what hardware is actually tracking
and causing PSR to exit.
BSpec: 7721
v4:
- Using _MMIO_TRANS2() in PSR_EVENT
- Cleaning events before printing
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180425212334.21109-2-jose.souza@intel.com
|
|
Any write in any display register was causing HW to exit PSR,
masking it to allow more power savings. Writes to pipe related
registers will still cause HW to exit PSR.
This is already masked for PSR2.
It also do not break the Display WA #0884, writes to CURSURFLIVE
are still causing hardware to exit PSR. This was tested in CNL machine
by triggering a write to CURSURFLIVE when a debugfs was read by user.
Bspec: 7721 and 8042
v4: Checked that it do not breaks WA #0884 and added this information
to the commit message.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180425212334.21109-1-jose.souza@intel.com
|
|
Make kernel print the correct number of TLB entries on Intel Xeon Phi 7210
(and others)
Before:
[ 0.320005] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
After:
[ 0.320005] Last level dTLB entries: 4KB 256, 2MB 128, 4MB 128, 1GB 16
The entries do exist in the official Intel SMD but the type column there is
incorrect (states "Cache" where it should read "TLB"), but the entries for
the values 0x6B, 0x6C and 0x6D are correctly described as 'Data TLB'.
Signed-off-by: Jacek Tomaka <jacek.tomaka@poczta.fm>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20180423161425.24366-1-jacekt@dugeo.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These are two watchdog-related fixes, fix for a backlight regression
from the 4.16 cycle that unfortunately was propagated to -stable and a
button module modification to prevent graphics driver modules from
failing to load due to unmet dependencies if ACPI is disabled from the
kernel command line.
Specifics:
- Change the ACPI subsystem initialization ordering to initialize the
WDAT watchodg before reserving PNP motherboard resources so as to
allow the watchdog to allocate its resources before the PNP code
gets to them and prevents it from working correctly (Mika
Westerberg).
- Add a quirk for Lenovo Z50-70 to use the iTCO watchdog instead of
the WDAT one which conflicts with the RTC on that platform (Mika
Westerberg).
- Avoid breaking backlight handling on Dell XPS 13 2013 model by
allowing laptops to use the ACPI backlight by default even if they
are Windows 8-ready in principle (Hans de Goede)"
* tag 'acpi-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Only default only_lcd to true on Win8-ready _desktops_
ACPI / button: make module loadable when booted in non-ACPI mode
ACPI / watchdog: Prefer iTCO_wdt on Lenovo Z50-70
ACPI / scan: Initialize watchdog before PNP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These are a Low Power S0 Idle quirk, a hibernation handling fix for
the PCI bus type and a brcmstb-avs-cpufreq driver fixup removing
development debug code from it.
Specifics:
- Blacklist the Low Power S0 Idle _DSM on ThinkPad X1 Tablet(2016)
where it causes issues and make it use ACPI S3 which works instead
of the non-working suspend-to-idle by default (Chen Yu).
- Fix the handling of hibernation in the PCI core for devices with
the DPM_FLAG_SMART_SUSPEND flag set to fix a regression affecting
intel-lpss I2C devices (Mika Westerberg).
- Drop development debug code from the brcmstb-avs-cpufreq driver
(Markus Mayer)"
* tag 'pm-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: brcmstb-avs-cpufreq: remove development debug support
PCI / PM: Do not clear state_saved in pci_pm_freeze() when smart suspend is set
ACPI / PM: Blacklist Low Power S0 Idle _DSM for ThinkPad X1 Tablet(2016)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random fixes from Ted Ts'o:
"Fix a regression on NUMA kernels and suppress excess unseeded entropy
pool warnings"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: rate limit unseeded randomness warnings
random: fix possible sleeping allocation from irq context
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of bug fixes:
- correct some CPU-MF counter names for z13 and z14
- correct locking in the vfio-ccw fsm_io_helper function
- provide arch_uretprobe_is_alive to avoid sigsegv with uretprobes
- fix a corner case with CPU-MF sampling in regard to execve
- fix expoline code revert for loadable modules
- update chpid descriptor for resource accessibility events
- fix dasd I/O errors due to outdated device alias infomation"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: correct module section names for expoline code revert
vfio: ccw: process ssch with interrupts disabled
s390: update sampling tag after task pid change
s390/cpum_cf: rename IBM z13/z14 counter names
s390/dasd: fix IO error for newly defined devices
s390/uprobes: implement arch_uretprobe_is_alive()
s390/cio: update chpid descriptor after resource accessibility event
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.17-rc3
Here are a few device ids for -rc3, including a new "simple driver".
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The block responsible of parsing the DT for the number of chip-select
lines uses an 'if/else if/else if' block. The content of the second and
third 'else if' conditions are:
1/ the actual condition to enter the sub-block and
2/ the operation to do in this sub-block.
[...]
else if (condition1_to_enter && action1() == failed)
raise_error();
else if (condition2_to_enter && action2() == failed)
raise_error();
[...]
In case of failure, the sub-block is entered and an error raised.
Otherwise, in case of success, the code would continue erroneously in
the next 'else if' statement because it did not failed (and did not
enter the first 'else if' sub-block).
The first 'else if' refers to legacy bindings while the second 'else if'
refers to new bindings. The second 'else if', which is entered
erroneously, checks for the 'reg' property, which, for old bindings,
does not mean anything because it would not be the number of CS
available, but the regular register map of almost any DT node. This
being said, the content of the 'reg' property being the register map
offset and length, it has '2' values, so the number of CS in this
situation is assumed to be '2'.
When running nand_scan_ident() with 2 CS, the core will check for an
array of chips. It will first issue a RESET and then a READ_ID. Of
course this will trigger two timeouts because there is no chip in front
of the second CS:
[ 1.367460] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000080)
[ 1.474292] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000280)
Indeed, this is harmless and the core will then assume there is only one
valid CS.
Fix the logic in the whole block by entering each sub-block just on the
'is legacy' condition, doing the action inside the sub-block. This way,
when the action succeeds, the whole block is left.
Furthermore, for both the old bindings and the new bindings the same
logic was applied to retrieve the number of CS lines:
using of_get_property() to get a size in bytes, converted in the actual
number of lines by dividing it per sizeof(u32) (4 bytes).
This is fine for the 'reg' property which is a list of the CS IDs but
not for the 'num-cs' property which is directly the value of the number
of CS.
Anyway, no existing DT uses another value than 'num-cs = <1>' and no
other value has ever been supported by the old driver (pxa3xx_nand.c).
Remove this condition and apply a number of 1 CS anyway, as already
described in the bindings.
Finally, the 'reg' property of a 'nand' node (with the new bindings)
gives the IDs of each CS line in use. marvell_nand.c driver first look
at the number of CS lines that are present in this property.
Better use of_property_count_elems_of_size() than dividing by 4 the size
of the number of bytes returned by of_get_property().
Fixes: 02f26ecf8c772 ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Even though we weren't injecting guilty requests to be reset, we could
still fall over the issue of resetting the same request too fast -- where
the GPU refuses to start again. (Although it is interesting to note that
reloading the driver is sufficient, suggesting that we could recover if
we delayed the setup after reset?) Continue to paper over the problem by
adding a small delay by waiting for the engine to idle between tests,
and ensure that the engines are idle before starting the idle tests.
v2: Replace single instance of 50 with a magic macro.
References: 028666793a02 ("drm/i915/selftests: Avoid repeatedly harming the same innocent context")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180411120346.27618-1-chris@chris-wilson.co.uk
|
|
It's possible for userspace to control n. Sanitize n when using it as an
array index.
Note that while it appears that n must be bound to the interval [0,3]
due to the way it is extracted from addr, we cannot guarantee that
compiler transformations (and/or future refactoring) will ensure this is
the case, and given this is a slow path it's better to always perform
the masking.
Found by smatch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
It's possible for userspace to control intid. Sanitize intid when using
it as an array index.
At the same time, sort the includes when adding <linux/nospec.h>.
Found by smatch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
It's possible for userspace to control idx. Sanitize idx when using it
as an array index.
Found by smatch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
ceph_con_workfn() validates con->state before calling try_read() and
then try_write(). However, try_read() temporarily releases con->mutex,
notably in process_message() and ceph_con_in_msg_alloc(), opening the
window for ceph_con_close() to sneak in, close the connection and
release con->sock. When try_write() is called on the assumption that
con->state is still valid (i.e. not STANDBY or CLOSED), a NULL sock
gets passed to the networking stack:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: selinux_socket_sendmsg+0x5/0x20
Make sure con->state is valid at the top of try_write() and add an
explicit BUG_ON for this, similar to try_read().
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/23706
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
|
|
Abstract compliance test adjustments to a single function. Also make the
bpc adjustments affect the limits, actually forcing the bpc. Seems like
directly changing the pipe_bpp in the past could not have been
effective.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ef61e76003ab7719c82810b742f3fb5765c0e14c.1524730974.git.jani.nikula@intel.com
|
|
For now, there's just the one link config selection, optimizing for slow
and wide link. No functional changes.
Keep the debug logging in the caller, to avoid duplication later on if
alternative link confing selection gets added.
v2: Improved commit message
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/64848b76bf90d6ceecd7ec6b5add28531e0b1a41.1524730974.git.jani.nikula@intel.com
|
|
Also use same min/max model for bpp, and adjust debug logging while at
it.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/72f78c7ae0cd1810798bd94cbf5e574c78da83f8.1524730974.git.jani.nikula@intel.com
|
|
Keep related things together. No functional changes.
v2: Fix a typo in patch subject, fix a checkpatch alignment warning.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f24d44547a586a0e342f24e69ab4d576a2474891.1524730974.git.jani.nikula@intel.com
|
|
Abstract a new intel_dp_compute_link_config() from
intel_dp_compute_config(), with the parts related to link configuration,
i.e. bpp, link rate, and lane count selection. No functional changes.
v2: Fix a checkpatch warn about spacing.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/80f99a625633f87f44d38d487ba3b32ff9a26b07.1524730974.git.jani.nikula@intel.com
|
|
We call intel_dp_compute_rate() in intel_dp_compute_config() only to be
able to debug log the link_bw and rate_select parameters; we don't use
the parameters here for anything else. We call intel_dp_compute_rate()
again during link training where we actually need and use the
parameters.
Move the debug logging of link_bw and rate_select to
intel_dp_link_training_clock_recovery(), and clean up the extra
intel_dp_compute_rate() call and extra clutter from the already
overcrowded intel_dp_compute_config().
v2: Rewrote commit message (Rodrigo, Manasi)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c5cf6a179e2d244eceb6bb80a792765d9efbee4f.1524730974.git.jani.nikula@intel.com
|
|
We haven't used the DP bw constants here for a while. No functional
changes.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1dc7763cdc70c7f64c0a01f76f218d9ac0717227.1524730974.git.jani.nikula@intel.com
|
|
Prefer INTEL_GEN() over INTEL_INFO()->gen except in special
circumstances.
v2: don't change device info dump (Chris)
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426113521.28417-1-jani.nikula@intel.com
|
|
This updates the Gemini defconfig with a config that will bring
up most of the recently merged and updated devices to some
functional level:
- We enable high resolution timers (the right thing to do)
- Enable CMA for the framebuffer, and the new TVE200
framebuffer driver and the Ilitek ILI9322 driver for
graphics on the D-Link DIR-685. HIGHMEM support comes in
as part of this.
- Enable networking and the new Cortina Gemini ethernet
driver.
- Enable MDIO over GPIO and the Realtek PHY devices used on
several of these systems.
- Enable I2C over GPIO and SPI over GPIO which is used on
several of these devices.
- Enable the Thermal framework, GPIO fan control and LM75 sensor
adding cooling on the D-Link DNS-313 with no userspace
involved even if only the kernel is working, rock solid
thermal for this platform.
- Enable JEDEC flash probing to support the Eon flash chip in
D-Link DNS-313.
- Enable LED disk triggers for the NAS type devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
One of the bitbanged SPI hosts had wrongly named GPIO lines due to
sloppiness by yours truly.
Cc: arm@kernel.org
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "Two fixes for v4.17-rc cycle" from Tony Lindgren:
Fix a build regression with split object directories reported by Russell
and fix range sizes for omap4 cm2 and prm modules.
* tag 'omap-for-v4.17/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix build when using split object directories
ARM: dts: Fix cm2 and prm sizes for omap4
|
|
For ACPI support of the HiSilicon LPC driver we depend
on MFD_CORE config.
Currently the HiSi LPC Kconfig entry does not define this
dependency, so add it.
The reason for depending on MFD_CORE in the driver is
that we model the LPC host as an MFD, in that a platform
device will be created for each device on the bus.
We do this as we need to modify the resources of these
derived platform devices, something which we should not
do to the original devices created in the ACPI scan.
Details in e0aa1563f894 ("HISI LPC: Add ACPI support").
Fixes: e0aa1563f894 ("HISI LPC: Add ACPI support")
Reported-and-tested-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Pull "Amlogic fixes for v4.17-rc1" from Kevin Hilman:
- add / enable USB host support for GX boards
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxm-khadas-vim2: enable the USB controller
ARM64: dts: meson-gxl-nexbox-a95x: enable the USB controller
ARM64: dts: meson-gxl-s905x-libretech-cc: enable the USB controller
ARM64: dts: meson-gx-p23x-q20x: enable the USB controller
ARM64: dts: meson-gxl-s905x-p212: enable the USB controller
ARM64: dts: meson-gxm: add GXM specific USB host configuration
ARM64: dts: meson-gxl: add USB host support
|
|
The DTS file for the NAS4220B had the pin config for the
ethernet interface set to the pins in the SL3512 SoC while
this system is using SL3516. Fix it by referencing the
right SL3516 pins instead of the SL3512 pins.
Cc: stable@vger.kernel.org
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Reported-by: Andreas Fiedler <andreas.fiedler@gmx.net>
Reported-by: Roman Yeryomin <roman@advem.lv>
Tested-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
I am leaving Axis, so this address will bounce in the not too
distant future.
Fortunately, I will still be working with the community.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes
SCMI fix for v4.17
A single patch eliminating the redundant null pointer check detected
by CoverityScan("Array compared against 0")
* tag 'scmi-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: remove redundant null check on array
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes
Pull "ARMv8 Juno DT fix for v4.17" from Sudeep Holla:
A single patch to fix the new DTC warnings probably enabled during
v4.17 merge window.
* tag 'juno-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: drop unnecessary address-cells and size-cells properties
|
|
https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom SoCs drivers fixes, please pull the
following:
- Geert makes the Raspberry Pi firmwware return -ENOSYS (similar to
other subsystems) when CONFIG_RASPBERRYPI_FIRMWARE is off.
- Florian fixes an incorrect annotation in the Raspberry Pi power domain
driver, spotted by sparse
* tag 'arm-soc/for-4.17/drivers-fixes' of https://github.com/Broadcom/stblinux:
soc: bcm2835: Make !RASPBERRYPI_FIRMWARE dummies return failure
soc: bcm: raspberrypi-power: Fix use of __packed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into fixes
ARM: socfpga_defconfig: fix QSPI Sector 4k
- disable CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
* tag 'socfpga_defconfig_fix_v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga_defconfig: Remove QSPI Sector 4K size force
|
|
The majority of the engine state dumping is too voluminous to be useful
outside of a controlled setup, though a few do accompany severe errors.
Keep the debug dumps next to the errors, but hide the others behind a CI
compile flag. This becomes more useful when adding more dumps to latency
sensitive paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426103219.22181-1-chris@chris-wilson.co.uk
|
