| Age | Commit message (Collapse) | Author |
|---|
|
Add audio codec cs42888 and related node.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add bluetooth audio codec.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GW75xx has a LIS2DE12TR 3-axis accelerometer on the I2C bus with an
interrupt pin. Add it to the device-tree.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PCIe[a,b] and SATA support for i.MX8QM-MEK board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PCIe support for i.MX8QXP MEK board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PCIe support on i.MX8DXL EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PCIe support for i.MX8QXP, i.MX8QM and i.MX8DXL.
Add SATA support for i.MX8QM, which is in hsio subsystem and is shared with
PCIe PHY.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is a spelling mistake of 'rewritting' in comments which
should be 'rewriting'.
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PDM micphone sound card support, configure the pinmux.
This sound card supports recording sound from PDM
microphone and convert the PDM format data to PCM data.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add wm8962 sound card which connects to sai3. The connection
of SAI3 and wm8962 is controlled by PCAL6524HEAZ module, add
gpio-hog for it.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add LPI2C[5,6] and the gpio expander subnodes.
Since we are at here, also add the alias for all lpi2c and gpio nodes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add 'nxp,ctrl-ids' for SCMI firmware to configure the board ctrls as
wakeup sources.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add cpuidle node and enable cpuidle for A55.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX95 has two on-chip temperature sensors, one is inside anamix block.
This is to add the anamix temperature thermal zone and its cooling
device.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update the thermal trip points for automotive and extended industrial
temperature qualification processors.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add SYS Power, BBM and MISC nodes under SCMI firmware node.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
With 'max-rx-timeout-ms' property added in 'Documentation/devicetree/
indings/firmware/arm,scmi.yaml', set the value for i.MX95.
NXP i.MX95 SCMI Firmware designation does not allow timeout, it will not
recover if the Agents use timeout design. So set a large value (5000ms)
here.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Kontron Electronics DL i.MX8MM consists of the BL i.MX8MM board
and a 7" LVDS panel. Provide an overlay that enables the panel.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Kontron Electronics BL i.MX8MM has oboard disply bridges for
DSI->HDMI and DSI->LVDS conversion. The DSI interface is muxed by
a GPIO-controlled switch to one of these two bridges.
By default the HDMI bridge is enabled. The LVDS bridge can be
selected by loading an additional (panel-specific) overlay.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove unused property cooling-max-state and cooling-min-state.
Remove undocument property #cooling-cells for ti,amc6821.
Fix below dtb_check warning:
arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-cx.dtb: fan-temperature-ctrlr@18: '#cooling-cells', 'cooling-max-state', 'cooling-min-state' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/hwmon/ti,amc6821.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
So far, only WFI is supported on i.MX8mp platform. Add support for
deeper cpuidle state "cpu-pd-wait" that would allow for better power
usage during runtime. This is a port from NXP downstream kernel.
Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
PCIe of i.MX8MP is dual role PCIe controller, which can work as root
complex (RC) mode and endpoint (EP) mode. Add overlay file to let it work
as EP mode.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add rev2 dtsi. Although uboot fixup can change compatible string
fsl,lx2160a-pcie to fsl,ls2088a-pcie since 2019, it is quite confused and
should correctly reflect hardware status. So add fsl-lx2160a-rev2.dtsi to
overwrite pcie's compatible string.
Add PCIe EP nodes.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for DH electronics i.MX8M Plus DHCOM SoM on PicoITX carrier board.
This system is populated with serial console, EQoS ethernet, eMMC, SD, SPI NOR,
LEDs and USB 3.0 host used in USB 2.0 mode on PicoITX.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update gpio-line-names. Add missing and remove unused.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for DH electronics i.MX8MP DHCOM SoM on DRC02 carrier board.
This system is populated with two ethernet ports, two CANs, RS485 and RS232,
USB, capacitive buttons and an OLED display.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The IOTA2 Lumpy board is based on the i.MX8MPlus EVK.
Basic features are:
- 4GB LPDDR4
- 64GB eMMC
- 2x 1GB Ethernet
- USB 3.0 Type-C dual role port, without power delivery
- USB 3.0 Type-A host port
- RGB LED - PWM driven
- speaker - PWM driven
- RTC with super capacitor backup
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add Toradex Verdin Ivy carrier board support. One notable feature of Ivy
is the analog inputs. These inputs are multiplexed, allowing the same
input to measure either voltage or current. For current measurements,
a GPIO switch enables or disables the shunt resistor. This process is
automatically managed by the Linux kernel using the IIO and MUX
subsystems. Voltage measurement is always enabled, but the voltage
measured by the ADC is scaled by a cascade voltage divider. In the
device tree, the equivalent gain of the voltage divider is used, which
can be calculated as follows:
------------
+ |
.-.
R1=30K | |
| |
'-'
|-------------------
Analog Input (AIN) | |
.-. .-.
R2=10K | | R3=30K | |
| | | |
'-' '-'
| |
| |--------
| .-. +
| R4=10K | |
| | | ADC Input (Channels 0 and 1)
| '-'
- | | -
-----------| |--------
=== ===
GND GND
Vin = Analog Input (AIN)
Vout = ADC Input
Rth = Thevenin Equiv. Resistance
Vth = Thevenin Equiv. Voltage
RL = Load Resistor
R1 = 30K, R2 = 10K, R3 = 30K, R4 = 10K
RL = R4 = 10K
Rth = (R1 // R2) + R3 = 37500 Ohms
Vth = (Vin * R2) / (R1 + R2) = Vin/4;
Vout = (Vth * RL)/ (Rth + RL) = Vth/4.75 = Vin/19
Gain = Vout/Vin = 1/19
https://www.toradex.com/products/carrier-board/ivy-carrier-board
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add labels to ti-ads1015 and fec ethernet mdio node to make it easier to
reference them from other nodes.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add Toradex Verdin Ivy carrier board support. One notable feature of Ivy
is the analog inputs. These inputs are multiplexed, allowing the same
input to measure either voltage or current. For current measurements,
a GPIO switch enables or disables the shunt resistor. This process is
automatically managed by the Linux kernel using the IIO and MUX
subsystems. Voltage measurement is always enabled, but the voltage
measured by the ADC is scaled by a cascade voltage divider. In the
device tree, the equivalent gain of the voltage divider is used, which
can be calculated as follows:
------------
+ |
.-.
R1=30K | |
| |
'-'
|-------------------
Analog Input (AIN) | |
.-. .-.
R2=10K | | R3=30K | |
| | | |
'-' '-'
| |
| |--------
| .-. +
| R4=10K | |
| | | ADC Input (Channels 0 and 1)
| '-'
- | | -
-----------| |--------
=== ===
GND GND
Vin = Analog Input (AIN)
Vout = ADC Input
Rth = Thevenin Equiv. Resistance
Vth = Thevenin Equiv. Voltage
RL = Load Resistor
R1 = 30K, R2 = 10K, R3 = 30K, R4 = 10K
RL = R4 = 10K
Rth = (R1 // R2) + R3 = 37500 Ohms
Vth = (Vin * R2) / (R1 + R2) = Vin/4;
Vout = (Vth * RL)/ (Rth + RL) = Vth/4.75 = Vin/19
Gain = Vout/Vin = 1/19
https://www.toradex.com/products/carrier-board/ivy-carrier-board
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a label to ti-ads1015 node to make it easier to reference it
from other nodes.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
A GPIO fan may be connected to Pollux fan header. The fan should
activate at 60°C and stay active until critical SoC temperature is
reached and the board shuts down.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The device tree defines the touchscreen controller, but it cannot be
enabled because it lacks a reference label.
This commit adds a label to allow it to be referenced and enabled.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add aliases for the RTCs on the Gateworks Venice boards and on the imx8m
SoC. This ensures that the primary RTC is always the one on-board
provided by the Gateworks System Controller (GSC) which is battery
backed as opposed to the one in the IMX8M.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add an overlay file to enable I3C support on the i.MX93, replacing I2C1
with I3C. I3C is compatible with I2C, but it has not yet been enabled in
arm64's defconfig. This overlay allows users to conveniently utilize I3C
on the imx93-9x9-qsb platform until I3C and its driver become more mature
and ready for full switch to I3C.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GW74xx D revision has added a M2SKT_GPIO10 GPIO which routes to the
GPIO10 pin of the M.2 socket for compatibility with certain devices.
Add the iomux and a line name for this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The DTS code coding style expects exactly one space before '{'
character.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds support for the Kontron Electronics i.MX8MP SMARC module
(which uses the OSM-S i.MX8MP SoM) on the Kontron SMARC eval carrier.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds support for the Kontron Electronics OSM-S i.MX8MP SoM
and the matching baseboard BL i.MX8MP.
The SoM hardware complies to the Open Standard Module (OSM) 1.1
specification, size S (https://sget.org/standards/osm).
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add wm8962 sound card which connects to sai3.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add flexcan support.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add io-expander adi,adp5585 under lpi2c3.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In lpi2c2 node, default pinctrl and sleep pinctrl have the same value.
So "sleep" pinctrl is redundant and remove it.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add following peripherals support for the Emtop i.MX8M Mini Baseboard
* Wi-Fi
* Audio
* SD card
* RTC
* CAN bus
* USB OTG
Signed-off-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add USB4 HOST to Apalis-iMX8QM SOM and its carrier boards.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for audio-codec NAU88C22 present on the Apalis Evaluation
Board v1.2 carrier board.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add audio support to Apalis-iMX8QM and its carrier boards. These includes:
* On SOM i2s sound card
* On SOM spdif sound card
* Enabling Audiomix and Asynchronous Sample Rate Converter
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Set critical/alert thermal thresholds for all relevant SOC
temperature trips to the IT value (max T_junction 105 degree
Celsius) in accordance with the IT grade of the SOM.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is no adma pwm on iMX8QM, so remove it from the DT. When enabled,
this cause warnings on resource partition ownership check by U-Boot
that receives messages from SCU firmware saying that these resources are
not owned:
Booting using the fdt blob at 0x9d400000
Loading Device Tree to 00000000fd622000, end 00000000fd66efff ... OK
Disable pwm@5a190000 rsrc 188 not owned
Disable clock-controller@5a590000 rsrc 188 not owned
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
