| Age | Commit message (Collapse) | Author |
|---|
|
In chunk_aligned_read() we are adding data_offset before calling
is_badblock. But is_badblock also adds data_offset, so that is bad.
So move the addition of data_offset to after the call to
is_badblock.
This bug was introduced by commit 31c176ecdf3563140e639
md/raid5: avoid reading from known bad blocks.
which first appeared in 3.0. So that patch is suitable for any
-stable kernel from 3.0.y onwards. However it will need minor
revision for most of those (as the comment didn't appear until
recently).
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If a RAID5 has both a failed device and a device marked as
'WantReplacement', then we should preferentially replace the failed
device.
However the current code replaces whichever is found first.
So split into 2 loops, check fail failed/missing first, and only check
for WantReplacement if nothing is failed or missing.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If a RAID10 has an odd number of chunks - as might happen when there
are an odd number of devices - the last chunk has no pair and so is
not mirrored. We don't store data there, but when recovering the last
device in an array we retry to recover that last chunk from a
non-existent location. This results in an error, and the recovery
aborts.
When we get to that last chunk we should just stop - there is nothing
more to do anyway.
This bug has been present since the introduction of RAID10, so the
patch is appropriate for any -stable kernel.
Cc: stable@vger.kernel.org
Reported-by: Christian Balzer <chibi@gol.com>
Tested-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
We only know of one so far.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Prune this down to just the struct kvm_irqfd so we can avoid
changing function definition for every flag or field we use.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
* 'fixes' of git://github.com/hzhuang1/linux:
ARM: pxa: hx4700: Fix basic suspend/resume
|
|
into next/cleanup
Nicolas Ferre <nicolas.ferre@atmel.com> writes:
A series about interrupt controller cleanup. AT91 AIC is moving to
fasteoi type of handler and sparse IRQ.
The Device Tree support is added to take into account priority
and external IRQ.
In addition to that, the new AIC5 IP is introduced.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'at91-for-next-cleanup' of git://github.com/at91linux/linux-at91:
ARM: at91: add AIC5 support
ARM: at91: remove mach/irqs.h
ARM: at91: sparse irq support
ARM: at91: at91 based machines specify their own irq handler at run time
ARM: at91: remove static irq priorities for sam9x5
ARM: at91: add of irq priorities support
ARM: at91: aic add dt support for external irqs
ARM: at91: aic can use fast eoi handler type
ARM: at91: fix at91_aic_write macro
ARM: at91: remove two unused headers
|
|
While we are resolving directory modifications in the
tree log, we are triggering delayed metadata updates to
the filesystem btrees.
This commit forces the delayed updates to run so the
replay code can find any modifications done. It stops
us from crashing because the directory deleltion replay
expects items to be removed immediately from the tree.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
cc: stable@kernel.org
|
|
We can race with unlink and not actually be able to do our igrab in
btrfs_add_ordered_extent. This will result in all sorts of problems.
Instead of doing the complicated work to try and handle returning an error
properly from btrfs_add_ordered_extent, just hold a ref to the inode during
writepages. If we cannot grab a ref we know we're freeing this inode anyway
and can just drop the dirty pages on the floor, because screw them we're
going to invalidate them anyway. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
The tree log stuff can have allocated space that we end up having split
across a bitmap and a real extent. The free space code does not deal with
this, it assumes that if it finds an extent or bitmap entry that the entire
range must fall within the entry it finds. This isn't necessarily the case,
so rework the remove function so it can handle this case properly. This
fixed two panics the user hit, first in the case where the space was
initially in a bitmap and then in an extent entry, and then the reverse
case. Thanks,
Reported-and-tested-by: Shaun Reich <sreich@kde.org>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
When we're evicting an inode during log recovery, we need to ensure that the inode
is not in orphan state any more, which means inode's run_time flags has _no_
BTRFS_INODE_HAS_ORPHAN_ITEM. Thus, the BUG_ON was triggered because of a wrong
check for the flags.
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
We used the wrong ioctl macro for the getflags ioctl before.
As we don't have the set/getflags ioctls in the user space ioctl.h
at the moment, it's safe to fix it now.
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Alexander Block <ablock84@googlemail.com>
|
|
This introduces btrfs_resume_balance_async(), which, given that
restriper state was recovered earlier by btrfs_recover_balance(),
resumes balance in btrfs-balance kthread.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Fix a bug that triggered asserts in btrfs_balance() in both normal and
resume modes -- restriper state was not properly restored on read-only
mounts. This factors out resuming code from btrfs_restore_balance(),
which is now also called earlier in the mount sequence to avoid the
problem of some early writes getting the old profile.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Miao pointed out there's a problem with mixing dio writes and buffered
reads. If the read happens between us invalidating the page range and
actually locking the extent we can bring in pages into page cache. Then
once the write finishes if somebody tries to read again it will just find
uptodate pages and we'll read stale data. So we need to lock the extent and
check for uptodate bits in the range. If there are uptodate bits we need to
unlock and invalidate again. This will keep this race from happening since
we will hold the extent locked until we create the ordered extent, and then
teh read side always waits for ordered extents. There was also a race in
how we updated i_size, previously we were relying on the generic DIO stuff
to adjust the i_size after the DIO had completed, but this happens outside
of the extent lock which means reads could come in and not see the updated
i_size. So instead move this work into where we create the extents, and
then this way the update ordered i_size stuff works properly in the endio
handlers. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
|
|
It is normal behaviour of the low level btrfs function btrfs_map_bio()
to complete a bio with -EIO if the device is missing, instead of just
preventing the bio creation in an earlier step.
This used to cause I/O statistic read error increments and annoying
printk_ratelimited messages. This commit fixes the issue.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Reported-by: Carey Underwood <cwillu@cwillu.com>
|
|
The number of lines of AIC5 has increased from 32 to 128. Due to this
increase, a source select register has been introduced for the interrupt
line selection. Moreover, register mapping has been changed. For that reasons,
we need some dedicated callbacks for AIC5.
Power management is also concerned by these changes. On suspend, we can't get
the whole interrupt mask register as before, we have to read this register 128
times. To reduce this overhead, a snapshot of the whole IMR is maintained.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
mach/irqs only defines FIQ_START which doesn't appear to be used anywhere
so remove it.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Enable sparse irq support for multisoc image. It involves to add the
NR_IRQS_LEGACY offset to static SoC irq number definitions since NR_IRQS_LEGACY
irq descs are allocated before AIC requests irq descs allocation.
Move NR_AIC_IRQS macro to a more appropiate place with the purpose to
remove mach/irqs.h later.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
SOC_AT91SAM9 selects MULTI_IRQ_HANDLER in order to let machines specify their
own IRQ handler at run time.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Since irq priorites are managed in DT, static ones are no more required for
sam9x5 which only has DT support.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add a third cell to define irq priority.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The Advanced Interrupt Controller allows us to use the fast EOI handler type.
It lets us remove the Atmel specific workaround into arch/arm/kernel/irq.c
used to indicate to the AIC the end of the interrupt treatment.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Fix at91_aic_write macro to avoid potential issues.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Commit 82c583e3ae31ffa76d1280197274cc1e1cde3179 ("AT91RM9200 hardware
headers") introduced arch/arm/mach-at91/include/mach/at91_spi.h and
arch/arm/mach-at91/include/mach/at91_ssc.h. (These files were called
at91rm9200_spi.h and at91rm9200_ssc.h then.) That commit was added in
the v2.6.18 development cycle.
Nothing includes them now and nothing uses the named constants they
provide. (There's no way these named constants could be used unless
these files were included somehow.) It actually seems these two headers
have never been used since they were added to the tree. They can safely
be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030
and interrupts from the PMIC are needed as wakeup sources.
Ensure this pin is mux'd as input and has wakeup enabled so PMIC
interupts (e.g. RTC) can be used as wakeup sources.
Tested on OMAP4430/Panda.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
In order for suspend/resume dependencies to work correctly, I2C has to
be initialized (more specifically, registered with the driver core)
before MMC. Without this, the MMC driver fails to adjust the VMMC
regulator (using i2c writes) during the suspend path.
Problem found testing suspend/resume on 3730/OveroSTORM platform.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit 435ca24 (ARM i.MX: Visstrim_M10: Add board version detection)
included <asm/system.h>, which is a header file about to be deleted according to
9f97da (Disintegrate asm/system.h for ARM)
Include <asm/system_info.h> instead.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Since we are taking a registers, this should never have been an sldi.
Talking to paulus offline, this is the correct fix.
Was introduced by:
commit 19ccb76a1938ab364a412253daec64613acbf3df
Author: Paul Mackerras <paulus@samba.org>
Date: Sat Jul 23 17:42:46 2011 +1000
Talking to paulus, this shouldn't be a literal.
Signed-off-by: Michael Neuling <mikey@neuling.org>
CC: <stable@kernel.org> [v3.2+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We have a bug report where the kernel hits a warning in the cpumask
code:
WARNING: at include/linux/cpumask.h:107
Which is:
WARN_ON_ONCE(cpu >= nr_cpumask_bits);
The backtrace is:
cpu_cmd
cmds
xmon_core
xmon
die
xmon is iterating through 0 to NR_CPUS. I'm not sure why we are still
open coding this but iterating above nr_cpu_ids is definitely a bug.
This patch iterates through all possible cpus, in case we issue a
system reset and CPUs in an offline state call in.
Perhaps the old code was trying to handle CPUs that were in the
partition but were never started (eg kexec into a kernel with an
nr_cpus= boot option). They are going to die way before we get into
xmon since we haven't set any kernel state up for them.
Signed-off-by: Anton Blanchard <anton@samba.org>
CC: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
There are a number of clkdev lookups left over from commit b0286f2
(ARM: imx6q: prepare and enable init on clks directly instead of
clk_get first), remove them since they are not needed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Pull two ARM fixes from Russell King:
"It's been fairly quiet with the fixes. Just two this time. One fixes
a long standing problem with KALLSYMS needing an additional pass, and
the other sorts a problem with the vmalloc space interacting with
static IO mappings."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7438/1: fill possible PMD empty section gaps
ARM: 7428/1: Prevent KALLSYM size mismatch on ARM.
|
|
On ARM with the 2-level page table format, a PMD entry is represented by
two consecutive section entries covering 2MB of virtual space.
However, static mappings always were allowed to use separate 1MB section
entries. This means in practice that a static mapping may create half
populated PMDs via create_mapping().
Since commit 0536bdf33f (ARM: move iotable mappings within the vmalloc
region) those static mappings are located in the vmalloc area. We must
ensure no such half populated PMDs are accessible once vmalloc() or
ioremap() start looking at the vmalloc area for nearby free virtual
address ranges, or various things leading to a kernel crash will happen.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: "R, Sricharan" <r.sricharan@ti.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Currently only used when packet split mode is enabled with jumbo frames,
IP payload checksum (for fragmented UDP packets) is mutually exclusive with
receive hashing offload since the hardware uses the same space in the
receive descriptor for the hardware-provided packet checksum and the RSS
hash, respectively. Users currently must disable jumbos when receive
hashing offload is enabled, or vice versa, because of this incompatibility.
Since testing has shown that IP payload checksum does not provide any real
benefit, just remove it so that there is no longer a choice between jumbos
or receive hashing offload but not both as done in other Intel GbE drivers
(e.g. e1000, igb).
Also, add a missing check for IP checksum error reported by the hardware;
let the stack verify the checksum when this happens.
CC: stable <stable@vger.kernel.org> [3.4]
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Basic suspend/resume is fixed by ensuring that the PGSR registers are
set correctly before sleep mode is entered. In particular four of the
active low resets need to be driven high while in sleep mode, otherwise
the unit resets itself instead of suspending. Another problem was that
the PCFR_GPROD bit is set by the HTC bootloader; this caused GPIO reset
(i.e. the reset button) to fail immediately after returning from sleep
mode.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
It was noticed recently that when we send data on a transport, its possible that
we might bundle a sack that arrived on a different transport. While this isn't
a major problem, it does go against the SHOULD requirement in section 6.4 of RFC
2960:
An endpoint SHOULD transmit reply chunks (e.g., SACK, HEARTBEAT ACK,
etc.) to the same destination transport address from which it
received the DATA or control chunk to which it is replying. This
rule should also be followed if the endpoint is bundling DATA chunks
together with the reply chunk.
This patch seeks to correct that. It restricts the bundling of sack operations
to only those transports which have moved the ctsn of the association forward
since the last sack. By doing this we guarantee that we only bundle outbound
saks on a transport that has received a chunk since the last sack. This brings
us into stricter compliance with the RFC.
Vlad had initially suggested that we strictly allow only sack bundling on the
transport that last moved the ctsn forward. While this makes sense, I was
concerned that doing so prevented us from bundling in the case where we had
received chunks that moved the ctsn on multiple transports. In those cases, the
RFC allows us to select any of the transports having received chunks to bundle
the sack on. so I've modified the approach to allow for that, by adding a state
variable to each transport that tracks weather it has moved the ctsn since the
last sack. This I think keeps our behavior (and performance), close enough to
our current profile that I think we can do this without a sysctl knob to
enable/disable it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yaseivch <vyasevich@gmail.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-sctp@vger.kernel.org
Reported-by: Michele Baldessari <michele@redhat.com>
Reported-by: sorin serban <sserban@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using ethtool -C ethX rx-usecs 0 crashes with a divide by zero.
Refactor this function to fix this issue and make it more clear
what the intent of each conditional is. Add comment regarding
using a setting of zero.
CC: stable <stable@vger.kernel.org> [3.3+]
CC: David Ahern <daahern@cisco.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes.
All are small, contained, targeted fixes for explicit problems --
mostly build and boot failures across i.MX, OMAP, Renesas/Shmobile and
Samsung."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6q: fix suspend regression caused by common clk migration
ARM: OMAP4470: Fix OMAP4470 boot failure
ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
ARM: shmobile: r8a7779: Route all interrupts to ARM
ARM: shmobile: kzm9d: use late init machine hook
ARM: shmobile: kzm9g: use late init machine hook
ARM: mach-shmobile: armadillo800eva: Use late init machine hook
ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
ARM: mach-shmobile: add missing GPIO IRQ configuration on mackerel
ARM: mach-shmobile: Fix build when SMP is enabled and EMEV2 is not enabled
ARM: shmobile: sh7372: bugfix: chclr_offset base
ARM: shmobile: sh73a0: bugfix: SY-DMAC number
ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL
|
|
Fix kernel-doc warnings in printk.c: use correct parameter name.
Warning(kernel/printk.c:2429): No description found for parameter 'buf'
Warning(kernel/printk.c:2429): Excess function parameter 'line' description in 'kmsg_dump_get_buffer'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix kernel-doc warning. This struct member was removed in commit
875682648b89 ("irq: Remove irq_chip->release()") so remove its
associated kernel-doc entry also.
Warning(include/linux/irq.h:338): Excess struct/union/enum/typedef member 'release' description in 'irq_chip'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.5-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL
|
|
When moving to common clk framework, the imx6q clks rom and mmdc_ch1_axi
get different on/off states than old clk driver, which breaks suspend
function. There might be a better way to manage these clocks, but let's
takes the old clk driver approach to fix the regression first.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"Here's one more regression fix that I missed earlier, and a
trivial fix to get omap4470 booting."
* tag 'omap-fixes-for-v3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4470: Fix OMAP4470 boot failure
ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull ACPI & Power Management patches from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
acpi_pad: fix power_saving thread deadlock
ACPI video: Still use ACPI backlight control if _DOS doesn't exist
ACPI, APEI, Avoid too much error reporting in runtime
ACPI: Add a quirk for "AMILO PRO V2030" to ignore the timer overriding
ACPI: Remove one board specific WARN when ignoring timer overriding
ACPI: Make acpi_skip_timer_override cover all source_irq==0 cases
ACPI, x86: fix Dell M6600 ACPI reboot regression via DMI
ACPI sysfs.c strlen fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver Core fixes from Greg Kroah-Hartman:
"Here is a number of printk() fixes, specifically a few reported by the
crazy blog program that ships in SUSE releases (that's "boot log" and
not "web log", it predates the general "blog" terminology by many
years), and the restoration of the continuation line functionality
reported by Stephen and others. Yes, the changes seem a bit big this
late in the cycle, but I've been beating on them for a while now, and
Stephen has even optimized it a bit, so all looks good to me.
The other change in here is a Documentation update for the stable
kernel rules describing how some distro patches should be backported,
to hopefully drive a bit more response from the distros to the stable
kernel releases.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
printk: Optimize if statement logic where newline exists
printk: flush continuation lines immediately to console
syslog: fill buffer with more than a single message for SYSLOG_ACTION_READ
Revert "printk: return -EINVAL if the message len is bigger than the buf size"
printk: fix regression in SYSLOG_ACTION_CLEAR
stable: Allow merging of backports for serious user-visible performance issues
|
|
'video-bugzilla-43168', 'bugzilla-40002' and 'bugfix-misc' into release
bug fixes
|
|
The acpi_pad driver can get stuck in destroy_power_saving_task()
waiting for kthread_stop() to stop a power_saving thread. The problem
is that the isolated_cpus_lock mutex is owned when
destroy_power_saving_task() calls kthread_stop(), which waits for a
power_saving thread to end, and the power_saving thread tries to
acquire the isolated_cpus_lock when it calls round_robin_cpu(). This
patch fixes the issue by making round_robin_cpu() use its own mutex.
https://bugzilla.kernel.org/show_bug.cgi?id=42981
Cc: stable@vger.kernel.org
Signed-off-by: Stuart Hayes <Stuart_Hayes@Dell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
