summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-08-17net: bridge: mdb: allow add/delete for host-joined groupsNikolay Aleksandrov
Currently this is needed only for user-space compatibility, so similar object adds/deletes as the dumped ones would succeed. Later it can be used for L2 mcast MAC add/delete. v3: fix compiler warning (DaveM) v2: don't send a notification when used from user-space, arm the group timer if no ports are left after host entry del Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-17net: bridge: mdb: dump host-joined entries as wellNikolay Aleksandrov
Currently we dump only the port mdb entries but we can have host-joined entries on the bridge itself and they should be treated as normal temp mdbs, they're already notified: $ bridge monitor all [MDB]dev br0 port br0 grp ff02::8 temp The group will not be shown in the bridge mdb output, but it takes 1 slot and it's timing out. If it's only host-joined then the mdb show output can even be empty. After this patch we show the host-joined groups: $ bridge mdb show dev br0 port br0 grp ff02::8 temp Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-17net: bridge: mdb: factor out mdb fillingNikolay Aleksandrov
We have to factor out the mdb fill portion in order to re-use it later for the bridge mdb entries. No functional changes intended. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-17net: bridge: mdb: move vlan commentsNikolay Aleksandrov
Trivial patch to move the vlan comments in their proper places above the vid 0 checks. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-17Merge branch 'net-phy-remove-genphy_config_init'David S. Miller
Heiner Kallweit says: ==================== net: phy: remove genphy_config_init Supported PHY features are either auto-detected or explicitly set. In both cases calling genphy_config_init isn't needed. All that genphy_config_init does is removing features that are set as supported but can't be auto-detected. Basically it duplicates the code in genphy_read_abilities. Therefore remove genphy_config_init. v2: - remove call also from new adin driver v3: - pass NULL as config_init function pointer for dp83848 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-17net: phy: remove genphy_config_initHeiner Kallweit
Now that all users have been removed we can remove genphy_config_init. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-17net: dsa: remove calls to genphy_config_initHeiner Kallweit
Supported PHY features are either auto-detected or explicitly set. In both cases calling genphy_config_init isn't needed. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-17net: phy: remove calls to genphy_config_initHeiner Kallweit
Supported PHY features are either auto-detected or explicitly set. In both cases calling genphy_config_init isn't needed. All that genphy_config_init does is removing features that are set as supported but can't be auto-detected. Basically it duplicates the code in genphy_read_abilities. Therefore remove such calls from all PHY drivers. v2: - remove call also from new adin PHY driver v3: - pass NULL as config_init function pointer for dp83848 Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-17MAINTAINERS: Fix Hyperv vIOMMU driver file nameLan Tianyu
The Hyperv vIOMMU file name should be "hyperv-iommu.c" rather than "hyperv_iommu.c". This patch is to fix it. Signed-off-by: Lan Tianyu <Tianyu.Lan@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-08-17tools: hv: Use the correct style for SPDX License IdentifierNishad Kamdar
This patch corrects the SPDX License Identifier style in the trace header file related to Microsoft Hyper-V client drivers. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used) Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46 Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-08-17tools: hv: fix typos in toolchainAdrian Vladu
Fix typos in the HyperV toolchain. Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sasha Levin <sashal@kernel.org> Cc: Alessandro Pilotti <apilotti@cloudbasesolutions.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-08-17tools: hv: fix KVP and VSS daemons exit codeAdrian Vladu
HyperV KVP and VSS daemons should exit with 0 when the '--help' or '-h' flags are used. Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sasha Levin <sashal@kernel.org> Cc: Alessandro Pilotti <apilotti@cloudbasesolutions.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-08-17tools: hv: fixed Python pep8/flake8 warnings for lsvmbusAdrian Vladu
Fixed pep8/flake8 python style code for lsvmbus tool. The TAB indentation was on purpose ignored (pep8 rule W191) to make sure the code is complying with the Linux code guideline. The following command doe not show any warnings now: pep8 --ignore=W191 lsvmbus flake8 --ignore=W191 lsvmbus Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sasha Levin <sashal@kernel.org> Cc: Dexuan Cui <decui@microsoft.com> Cc: Alessandro Pilotti <apilotti@cloudbasesolutions.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-08-17Merge branch 'i2c/for-current' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: "I2C has one revert because of a regression, two fixes for tiny race windows (which we were not able to trigger), a MAINTAINERS addition, and a SPDX fix" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: stm32: Use the correct style for SPDX License Identifier i2c: emev2: avoid race when unregistering slave client i2c: rcar: avoid race when unregistering slave client MAINTAINERS: i2c-imx: take over maintainership Revert "i2c: imx: improve the error handling in i2c_imx_dma_request()"
2019-08-17Merge tag 'riscv/for-v5.3-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V fixes from Paul Walmsley: - Two patches to fix significant bugs in floating point register context handling - A minor fix in RISC-V flush_tlb_page(), to supply a valid end address to flush_tlb_range() - Two minor defconfig additions: to build the virtio hwrng driver by default (for QEMU targets), and to partially synchronize the 32-bit defconfig with the 64-bit defconfig * tag 'riscv/for-v5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: riscv: Make __fstate_clean() work correctly. riscv: Correct the initialized flow of FP register riscv: defconfig: Update the defconfig riscv: rv32_defconfig: Update the defconfig riscv: fix flush_tlb_range() end address for flush_tlb_page()
2019-08-17Merge tag 'usb-serial-5.3-rc5' of ↵Greg Kroah-Hartman
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus Johan writes: USB-serial fixes for 5.3-rc5 Here are some new modem device ids. All have been in linux-next with no reported issues. Signed-off-by: Johan Hovold <johan@kernel.org> * tag 'usb-serial-5.3-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: option: add the BroadMobi BM818 card USB: serial: option: Add Motorola modem UARTs USB: serial: option: add D-Link DWM-222 device ID USB: serial: option: Add support for ZTE MF871A
2019-08-17Bluetooth: Add debug setting for changing minimum encryption key sizeMarcel Holtmann
For testing and qualification purposes it is useful to allow changing the minimum encryption key size value that the host stack is going to enforce. This adds a new debugfs setting min_encrypt_key_size to achieve this functionality. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2019-08-16Merge tag 'xtensa-20190816' of git://github.com/jcmvbkbc/linux-xtensaLinus Torvalds
Pull Xtensa fix from Max Filippov: "Add missing isync into cpu_reset to make sure ITLB changes are effective" * tag 'xtensa-20190816' of git://github.com/jcmvbkbc/linux-xtensa: xtensa: add missing isync to the cpu_reset TLB code
2019-08-16tipc: fix false detection of retransmit failuresTuong Lien
This commit eliminates the use of the link 'stale_limit' & 'prev_from' (besides the already removed - 'stale_cnt') variables in the detection of repeated retransmit failures as there is no proper way to initialize them to avoid a false detection, i.e. it is not really a retransmission failure but due to a garbage values in the variables. Instead, a jiffies variable will be added to individual skbs (like the way we restrict the skb retransmissions) in order to mark the first skb retransmit time. Later on, at the next retransmissions, the timestamp will be checked to see if the skb in the link transmq is "too stale", that is, the link tolerance time has passed, so that a link reset will be ordered. Note, just checking on the first skb in the queue is fine enough since it must be the oldest one. A counter is also added to keep track the actual skb retransmissions' number for later checking when the failure happens. The downside of this approach is that the skb->cb[] buffer is about to be exhausted, however it is always able to allocate another memory area and keep a reference to it when needed. Fixes: 77cf8edbc0e7 ("tipc: simplify stale link failure criteria") Reported-by: Hoang Le <hoang.h.le@dektech.com.au> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16ipvlan: set hw_enc_features like macvlanBill Sommerfeld
Allow encapsulated packets sent to tunnels layered over ipvlan to use offloads rather than forcing SW fallbacks. Since commit f21e5077010acda73a60 ("macvlan: add offload features for encapsulation"), macvlan has set dev->hw_enc_features to include everything in dev->features; do likewise in ipvlan. Signed-off-by: Bill Sommerfeld <wsommerfeld@google.com> Acked-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16selftests: Fix get_ifidx and callers in nettest.cDavid Ahern
Dan reported: The patch acda655fefae: "selftests: Add nettest" from Aug 1, 2019, leads to the following static checker warning: ./tools/testing/selftests/net/nettest.c:1690 main() warn: unsigned 'tmp' is never less than zero. ./tools/testing/selftests/net/nettest.c 1680 case '1': 1681 args.has_expected_raddr = 1; 1682 if (convert_addr(&args, optarg, 1683 ADDR_TYPE_EXPECTED_REMOTE)) 1684 return 1; 1685 1686 break; 1687 case '2': 1688 if (str_to_uint(optarg, 0, 0x7ffffff, &tmp) != 0) { 1689 tmp = get_ifidx(optarg); 1690 if (tmp < 0) { "tmp" is unsigned so it can't be negative. Also all the callers assume that get_ifidx() returns negatives on error but it looks like it really returns zero on error so it's a bit unclear to me. Update get_ifidx to return -1 on errors and cleanup callers of it. Fixes: acda655fefae ("selftests: Add nettest") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16lan78xx: Fix memory leaksWenwen Wang
In lan78xx_probe(), a new urb is allocated through usb_alloc_urb() and saved to 'dev->urb_intr'. However, in the following execution, if an error occurs, 'dev->urb_intr' is not deallocated, leading to memory leaks. To fix this issue, invoke usb_free_urb() to free the allocated urb before returning from the function. Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: dsa: mv88e6xxx: check for mode change in port_setup_macMarek Behún
The mv88e6xxx_port_setup_mac checks if the requested MAC settings are different from the current ones, and if not, does nothing (since chaning them requires putting the link down). In this check it only looks if the triplet [link, speed, duplex] is being changed. This patch adds support to also check if the mode parameter (of type phy_interface_t) is requested to be changed. The current mode is computed by the ->port_link_state() method, and if it is different from PHY_INTERFACE_MODE_NA, we check for equality with the requested mode. In the implementations of the mv88e6250_port_link_state() method we set the current mode to PHY_INTERFACE_MODE_NA - so the code does not check for mode change on 6250. In the mv88e6352_port_link_state() method, we use the cached cmode of the port to determine the mode as phy_interface_t (and if it is not enough, eg. for RGMII, we also look at the port control register for RX/TX timings). Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16MAINTAINERS: r8169: Update path to the driverDenis Efremov
Update MAINTAINERS record to reflect the filename change. The file was moved in commit 25e992a4603c ("r8169: rename r8169.c to r8169_main.c") Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: nic_swsd@realtek.com Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: Denis Efremov <efremov@linux.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16MAINTAINERS: PHY LIBRARY: Update files in the recordDenis Efremov
Update MAINTAINERS to reflect that sysfs-bus-mdio was removed in commit a6cd0d2d493a ("Documentation: net-sysfs: Remove duplicate PHY device documentation") and sysfs-class-net-phydev was added in commit 86f22d04dfb5 ("net: sysfs: Document PHY device sysfs attributes"). Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: Denis Efremov <efremov@linux.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16Merge branch 'net-phy-adin-add-support-for-Analog-Devices-PHYs'David S. Miller
Alexandru Ardelean says: ==================== net: phy: adin: add support for Analog Devices PHYs This changeset adds support for Analog Devices Industrial Ethernet PHYs. Particularly the PHYs this driver adds support for: * ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY * ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit Ethernet PHY The 2 chips are register compatible with one another. The main difference being that ADIN1200 doesn't operate in gigabit mode. The chips can be operated by the Generic PHY driver as well via the standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the kernel as well. This assumes that configuration of the PHY has been done completely in HW, according to spec, i.e. no extra SW configuration required. This changeset also implements the ability to configure the chips via SW registers. Datasheets: https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1300.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1200.pdf ==================== Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16dt-bindings: net: add bindings for ADIN PHY driverAlexandru Ardelean
This change adds bindings for the Analog Devices ADIN PHY driver, detailing all the properties implemented by the driver. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: add ethtool get_stats supportAlexandru Ardelean
This change implements retrieving all the error counters from the PHY. The counters require that the RxErrCnt register (0x0014) be read first, after which copies of the counters are latched into the registers. This ensures that all registers read after RxErrCnt are synchronized at the moment that they are read. The counter values need to be accumulated by the driver, as each time that RxErrCnt is read, the values that are latched are the ones that have incremented from the last read. Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: implement downshift configuration via phy-tunableAlexandru Ardelean
Down-speed auto-negotiation may not always be enabled, in which case the PHY won't down-shift to 100 or 10 during auto-negotiation. This change enables downshift and configures the number of retries to default 4 (which is also in the datasheet The downshift control mechanism can also be controlled via the phy-tunable interface (ETHTOOL_PHY_DOWNSHIFT control). The change has been adapted from the Aquantia PHY driver. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: implement PHY subsystem software resetAlexandru Ardelean
The ADIN PHYs supports 4 types of reset: 1. The standard PHY reset via BMCR_RESET bit in MII_BMCR reg 2. Reset via GPIO 3. Reset via reg GeSftRst (0xff0c) & reload previous pin configs 4. Reset via reg GeSftRst (0xff0c) & request new pin configs Resets 2, 3 & 4 are almost identical, with the exception that the crystal oscillator is available during reset for 2. This change implements subsystem software reset via the GeSftRst and reloading the previous pin configuration (so reset number 3). This will also reset the PHY core regs (similar to reset 1). Since writing bit 1 to reg GeSftRst is self-clearing, the only thing that can be done, is to write to that register, wait a specific amount of time (10 milliseconds should be enough) and try to read back and check if there are no errors on read. A busy-wait-read won't work well, and may sometimes work or not work. In case phylib is configured to also do a reset via GPIO, the ADIN PHY may be reset twice when the PHY device registers, but that isn't a problem, since it's being done on boot (or PHY device register). Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: add EEE translation layer from Clause 45 to Clause 22Alexandru Ardelean
The ADIN1200 & ADIN1300 PHYs support EEE by using standard Clause 45 access to access MMD registers for EEE. The EEE register addresses (when using Clause 22) are available at different addresses (than Clause 45), and since accessing these regs (via Clause 22) needs a special mechanism, a translation table is required to convert these addresses. For Clause 45, this is not needed since the driver will likely never use this access mode. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: add support MDI/MDIX/Auto-MDI selectionAlexandru Ardelean
The ADIN PHYs support automatic MDI/MDIX negotiation. By default this is disabled, so this is enabled at `config_init`. This is controlled via the PHY Control 1 register. The supported modes are: 1. Manual MDI 2. Manual MDIX 3. Auto MDIX - prefer MDIX 4. Auto MDIX - prefer MDI The phydev mdix & mdix_ctrl fields include modes 3 & 4 into a single auto-mode. So, the default mode this driver enables is 4 when Auto-MDI mode is used. When detecting MDI/MDIX mode, a combination of the PHY Control 1 register and PHY Status 1 register is used to determine the correct MDI/MDIX mode. If Auto-MDI mode is not set, then the manual MDI/MDIX mode is returned. If Auto-MDI mode is set, then MDIX mode is returned differs from the preferred MDI/MDIX mode. This covers all cases where: 1. MDI preferred & Pair01Swapped == MDIX 2. MDIX preferred & Pair01Swapped == MDI 3. MDI preferred & ! Pair01Swapped == MDIX 4. MDIX preferred & ! Pair01Swapped == MDI The preferred MDI/MDIX mode is not configured via SW, but can be configured via HW pins. Note that the `Pair01Swapped` is the Green-Yellow physical pairs. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: make RMII fifo depth configurableAlexandru Ardelean
The FIFO depth can be configured for the RMII mode. This change adds support for doing this via device-tree (or ACPI). Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: make RGMII internal delays configurableAlexandru Ardelean
The internal delays for the RGMII are configurable for both RX & TX. This change adds support for configuring them via device-tree (or ACPI). Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: configure RGMII/RMII/MII modes on configAlexandru Ardelean
The ADIN1300 chip supports RGMII, RMII & MII modes. Default (if unconfigured) is RGMII. This change adds support for configuring these modes via the device registers. For RGMII with internal delays (modes RGMII_ID,RGMII_TXID, RGMII_RXID), the default delay is 2 ns. This can be configurable and will be done in a subsequent change. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: add {write,read}_mmd hooksAlexandru Ardelean
Both ADIN1200 & ADIN1300 support Clause 45 access for some registers. The Extended Management Interface (EMI) registers are accessible via both Clause 45 (at register MDIO_MMD_VEND1) and using Clause 22. The Clause 22 access for MMD regs differs from the standard one defined by 802.3. The ADIN PHYs use registers ExtRegPtr (0x0010) and ExtRegData (0x0011) to access Clause 45 & EMI registers. The indirect access is done via the following mechanism (for both R/W): 1. Write the address of the register in the ExtRegPtr 2. Read/write the value of the register via reg ExtRegData This mechanism is needed to manage configuration of chip settings and to access EEE registers via Clause 22. Since Clause 45 access will likely never be used, it is not implemented via this hook. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: add support for interruptsAlexandru Ardelean
This change hooks link-status-change interrupts to phylib. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: hook genphy_{suspend, resume} into the driverAlexandru Ardelean
The chip supports standard suspend/resume via BMCR reg. Hook these functions into the `adin` driver. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16net: phy: adin: add support for Analog Devices PHYsAlexandru Ardelean
This change adds support for Analog Devices Industrial Ethernet PHYs. Particularly the PHYs this driver adds support for: * ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY * ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit Ethernet PHY The 2 chips are register compatible with one another. The main difference being that ADIN1200 doesn't operate in gigabit mode. The chips can be operated by the Generic PHY driver as well via the standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the kernel as well. This assumes that configuration of the PHY has been done completely in HW, according to spec. Configuration can also be done via registers, which will be supported by this driver. Datasheets: https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1300.pdf https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1200.pdf Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-16Merge tag 'arm64-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fixes from Catalin Marinas: - Don't taint the kernel if CPUs have different sets of page sizes supported (other than the one in use). - Issue I-cache maintenance for module ftrace trampoline. * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: ftrace: Ensure module ftrace trampoline is coherent with I-side arm64: cpufeature: Don't treat granule sizes as strict
2019-08-16arm64: ftrace: Ensure module ftrace trampoline is coherent with I-sideWill Deacon
The initial support for dynamic ftrace trampolines in modules made use of an indirect branch which loaded its target from the beginning of a special section (e71a4e1bebaf7 ("arm64: ftrace: add support for far branches to dynamic ftrace")). Since no instructions were being patched, no cache maintenance was needed. However, later in be0f272bfc83 ("arm64: ftrace: emit ftrace-mod.o contents through code") this code was reworked to output the trampoline instructions directly into the PLT entry but, unfortunately, the necessary cache maintenance was overlooked. Add a call to __flush_icache_range() after writing the new trampoline instructions but before patching in the branch to the trampoline. Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: James Morse <james.morse@arm.com> Cc: <stable@vger.kernel.org> Fixes: be0f272bfc83 ("arm64: ftrace: emit ftrace-mod.o contents through code") Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2019-08-16Merge tag 'pm-5.3-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management fixes from Rafael Wysocki: "These add a check to avoid recent suspend-to-idle power regression on systems with NVMe drives where the PCIe ASPM policy is "performance" (or when the kernel is built without ASPM support), fix an issue related to frequency limits in the schedutil cpufreq governor and fix a mistake related to the PM QoS usage in the cpufreq core introduced recently. Specifics: - Disable NVMe power optimization related to suspend-to-idle added recently on systems where PCIe ASPM is not able to put PCIe links into low-power states to prevent excess power from being drawn by the system while suspended (Rafael Wysocki). - Make the schedutil governor handle frequency limits changes properly in all cases (Viresh Kumar). - Prevent the cpufreq core from treating positive values returned by dev_pm_qos_update_request() as errors (Viresh Kumar)" * tag 'pm-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: nvme-pci: Allow PCI bus-level PM to be used if ASPM is disabled PCI/ASPM: Add pcie_aspm_enabled() cpufreq: schedutil: Don't skip freq update when limits change cpufreq: dev_pm_qos_update_request() can return 1 on success
2019-08-16Merge tag 'dmaengine-fix-5.3-rc5' of ↵Linus Torvalds
git://git.infradead.org/users/vkoul/slave-dma Pull dmaengine fixes from Vinod Koul: "Fixes in dmaengine drivers for: - dw-edma: endianess, _iomem type and stack usages - ste_dma40: unneeded variable and null-pointer dereference - tegra210-adma: unused function - omap-dma: off-by-one fix" * tag 'dmaengine-fix-5.3-rc5' of git://git.infradead.org/users/vkoul/slave-dma: omap-dma/omap_vout_vrfb: fix off-by-one fi value dmaengine: stm32-mdma: Fix a possible null-pointer dereference in stm32_mdma_irq_handler() dmaengine: tegra210-adma: Fix unused function warnings dmaengine: ste_dma40: fix unneeded variable warning dmaengine: dw-edma: fix endianess confusion dmaengine: dw-edma: fix __iomem type confusion dmaengine: dw-edma: fix unnecessary stack usage
2019-08-16Merge tag 'sound-5.3-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound fixes from Takashi Iwai: "All small fixes targeted for stable: - Two fixes for USB-audio with malformed descriptor, spotted by fuzzers - Two fixes Conexant HD-audio codec wrt power management - Quirks for HD-audio AMD platform and HP laptop - HD-audio memory leak fix" * tag 'sound-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: usb-audio: Fix a stack buffer overflow bug in check_input_term ALSA: usb-audio: Fix an OOB bug in parse_audio_mixer_unit ALSA: hda - Add a generic reboot_notify ALSA: hda - Let all conexant codec enter D3 when rebooting ALSA: hda/realtek - Add quirk for HP Envy x360 ALSA: hda - Fix a memory leak bug ALSA: hda - Apply workaround for another AMD chip 1022:1487
2019-08-16Merge tag 'drm-fixes-2019-08-16' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm fixes from Dave Airlie: "Nothing too crazy this week, one amdgpu fix to use vmalloc for a struct that grew in size, and another MST fix for nouveau, and some other misc fixes: i915: - single GVT use after free fix scheduler: - entity destruction race fix amdgpu: - struct allocation fix - gfx9 soft recovery fix nouveau: - followup MST fix ast: - vga register race fix" * tag 'drm-fixes-2019-08-16' of git://anongit.freedesktop.org/drm/drm: drm/nouveau: Only recalculate PBN/VCPI on mode/connector changes drm/ast: Fixed reboot test may cause system hanged drm/scheduler: use job count instead of peek drm/amd/display: use kvmalloc for dc_state (v2) drm/amdgpu: fix gfx9 soft recovery drm/i915: Use after free in error path in intel_vgpu_create_workload()
2019-08-16Merge branch 'pm-cpufreq'Rafael J. Wysocki
* pm-cpufreq: cpufreq: schedutil: Don't skip freq update when limits change cpufreq: dev_pm_qos_update_request() can return 1 on success
2019-08-16x86/boot: Save fields explicitly, zero out everything elseJohn Hubbard
Recent gcc compilers (gcc 9.1) generate warnings about an out of bounds memset, if the memset goes accross several fields of a struct. This generated a couple of warnings on x86_64 builds in sanitize_boot_params(). Fix this by explicitly saving the fields in struct boot_params that are intended to be preserved, and zeroing all the rest. [ tglx: Tagged for stable as it breaks the warning free build there as well ] Suggested-by: Thomas Gleixner <tglx@linutronix.de> Suggested-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: John Hubbard <jhubbard@nvidia.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190731054627.5627-2-jhubbard@nvidia.com
2019-08-16Merge tag 'soundwire-5.3-rc5' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-linus Vinod writes: soundwire fixes for v5.3-rc5 Pierre sent fixes which are queued now for v5.3-rc5 are: - regmap dependecy - cadence register definitions * tag 'soundwire-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: soundwire: fix regmap dependencies and align with other serial links soundwire: cadence_master: fix definitions for INTSTAT0/1 soundwire: cadence_master: fix register definition for SLAVE_STATE
2019-08-16Merge tag 'drm-intel-fixes-2019-08-15' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes drm/i915 fixes for v5.4-rc5: - GVT use-after-free fix Signed-off-by: Dave Airlie <airlied@redhat.com> From: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/87zhkag9ic.fsf@intel.com
2019-08-15Merge tag 'rxrpc-fixes-20190814' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs David Howells says: ==================== rxrpc: Fix local endpoint handling Here's a pair of patches that fix two issues in the handling of local endpoints (rxrpc_local structs): (1) Use list_replace_init() rather than list_replace() if we're going to unconditionally delete the replaced item later, lest the list get corrupted. (2) Don't access the rxrpc_local object after passing our ref to the workqueue, not even to illuminate tracepoints, as the work function may cause the object to be freed. We have to cache the information beforehand. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-02 17:10:49 +0000