summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-12-23drm/amdgpu: Add mmCOMPUTE_STATIC_THREAD_MGMT_SE4-7 to support ArcturusJames Zhu
Arcturus has 8 SEs. Add mmCOMPUTE_STATIC_THREAD_MGMT_SE4-7 for EDC GPR _workarounds, Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Yong Zhao <Yong.Zhao@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-12-23drm/amdgpu: Added ASIC specific check in gmc v9.0 ECC interrupt programming ↵John Clements
sequence Devices newer then VEGA10/12 shall have these programming sequences performed by PSP BL Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: John Clements <john.clements@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-12-23drm/amdgpu: enlarge agp_start address into 48bitFrank.Min
max range of the agp aperture is 48 bits, so enlarge agp_start address into 48bit with all bits set Signed-off-by: Frank.Min <Frank.Min@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-12-23drm/amdgpu: disable VCN2.5 ib test for Arcturus sriovJane Jian
currently using TMR loading VCN fw MMSCH would fail to init after FLR, just disable ib test for temporarily daily testing, continuing debug with mm team. Signed-off-by: Jane Jian <Jane.Jian@amd.com> Acked-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-12-23drm/amdgpu: fix ctx init failure for asics without gfx ringLe Ma
This workaround does not affect other asics because amdgpu only need expose one gfx sched to user for now. Signed-off-by: Le Ma <le.ma@amd.com> Reviewed-by: Nirmoy Das <nirmoy.das@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-12-23drm/amdgpu: attempt xgmi perfmon re-arm on failed armJonathan Kim
The DF routines to arm xGMI performance will attempt to re-arm both on performance monitoring start and read on initial failure to arm. Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-12-23drm/amdgpu: add perfmons accessible during df c-statesJonathan Kim
During DF C-State, Perfmon counters outside of range 1D700-1D7FF will encounter SLVERR affecting xGMI performance monitoring. PerfmonCtr[7:4] is being added to avoid SLVERR during read since it falls within this range. PerfmonCtl[7:4] is being added in order to arm PerfmonCtr[7:4]. Since PerfmonCtl[7:4] exists outside of range 1D700-1D7FF, DF routines will be enabled to opportunistically re-arm PerfmonCtl[7:4] on retry after SLVERR. Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com> Acked-by: Alex Deucher <Alexander.Deucher@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-12-23drm/amdgpu: simplify padding calculations (v2)Luben Tuikov
Simplify padding calculations. v2: Comment update and spacing. Signed-off-by: Luben Tuikov <luben.tuikov@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-12-23drm/i915: Update DRIVER_DATE to 20191223Jani Nikula
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2019-12-23drm/i915: Mark the GEM context link as RCU protectedChris Wilson
The only protection for intel_context.gem_cotext is granted by RCU, so annotate it as a rcu protected pointer and carefully dereference it in the few occasions we need to use it. Fixes: 9f3ccd40acf4 ("drm/i915: Drop GEM context as a direct link from i915_request") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Andi Shyti <andi.shyti@intel.com> Acked-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191222233558.2201901-1-chris@chris-wilson.co.uk
2019-12-23drm/i915: Introduce a vma.krefChris Wilson
Start introducing a kref on i915_vma in order to protect the vma unbind (i915_gem_object_unbind) from a parallel destruction (i915_vma_parked). Later, we will use the refcount to manage all access and turn i915_vma into a first class container. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Imre Deak <imre.deak@intel.com> Acked-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191222210256.2066451-2-chris@chris-wilson.co.uk
2019-12-23drm/i915: Add a simple is-bound check before unbindingChris Wilson
Only acquire the various atomic references required to unbind the vma if we do need to unbind the vma. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191222210256.2066451-1-chris@chris-wilson.co.uk
2019-12-23drm/i915: Make sure CCS YUV semiplanar format checks workImre Deak
For CCS formats, the current DRM core check for YUV semiplanar formats doesn't work; use an i915 specific function for that. v2: Fix checkpatch warnings. Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-11-imre.deak@intel.com
2019-12-23drm/i915: Make sure Y slave planes get all the required stateImre Deak
Y planes program the offset and stride of the AUX plane, so make sure we copy the required info for this into their plane state. Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-10-imre.deak@intel.com
2019-12-23drm/i915: Skip rotated offset adjustment for unsupported modifiersDhinakaran Pandiyan
During framebuffer creation, we pre-compute offsets for 90/270 plane rotation. However, only Y and Yf modifiers support 90/270 rotation. So, skip the calculations for other modifiers. To keep the gem buffer size check still working for tiled planes, factor out the logic needed for rotation setup and skip only this part for tiled planes other than Y/Yf. v2: Add a bounds check WARN for the rotation info array. v3: Keep the gem buffer size check working for tiled planes. Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-9-imre.deak@intel.com
2019-12-23drm/i915/tgl: Make sure FBs have a correct CCS plane strideImre Deak
The CCS plane stride must be fixed on TGL, as it's not configurable for the display. Instead the HW has a hardwired logic to determine it from the main plane stride. Make sure userspace passes in the correct stride. Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-8-imre.deak@intel.com
2019-12-23drm/i915/tgl: Gen-12 render decompressionDhinakaran Pandiyan
Gen-12 display decompression operates on Y-tiled compressed main surface. The CCS is linear and has 4 bits of metadata for each main surface cache line pair, a size ratio of 1:256. Gen-12 display decompression is incompatible with buffers compressed by earlier GPUs, so make use of a new modifier to identify gen-12 compression. Another notable change is that render decompression is supported on all planes except cursor and on all pipes. Start by adding render decompression support for [A,X]BGR888 pixel formats. v2: Fix checkpatch warnings (Lucas) v3: Rebase, disable color clear, styling changes and modify intel_tile_width_bytes and intel_tile_height to handle linear CCS v4: - Use format block descriptors and the i915 specific func to get the subsampling for each color plane. - Use helpers to convert between CCS and main planes. v5: - Fix subsampling returned by intel_fb_plane_get_subsampling() for the CCS plane of the first plane. v6: - Rebased on v2 of patch 4. v7: - Fix plane dimensions during FB check. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Nanley G Chery <nanley.g.chery@intel.com> Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> (v6) Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-7-imre.deak@intel.com
2019-12-23drm/framebuffer: Format modifier for Intel Gen-12 render compressionDhinakaran Pandiyan
Gen-12 has a new compression format, add a new modifier to indicate that. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Nanley G Chery <nanley.g.chery@intel.com> Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: Mika Kahola <mika.kahola@intel.com> Cc: dri-devel@lists.freedesktop.org Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-6-imre.deak@intel.com
2019-12-23drm/i915: Add helpers to select correct ccs/aux planesImre Deak
Using helpers instead of open coding this to select a CCS plane for a main plane makes the code cleaner and less error-prone when the location of CCS plane can be different based on the format (packed vs. YUV semiplanar). The same applies to selecting an AUX plane which can be a UV plane (for an uncompressed YUV semiplanar format), or a CCS plane. Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-5-imre.deak@intel.com
2019-12-23drm/i915: Extract framebufer CCS offset checks into a functionDhinakaran Pandiyan
intel_fill_fb_info() has grown quite large and wrapping the offset checks into a separate function makes the loop a bit easier to follow. v2: Skip the check for non-CCS planes. (Mika) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-4-imre.deak@intel.com
2019-12-23drm/i915: Move CCS stride alignment W/A inside intel_fb_stride_alignmentDhinakaran Pandiyan
Easier to read if all the alignment changes are in one place and contained within a function. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-3-imre.deak@intel.com
2019-12-23drm/i915: Use intel_tile_height() instead of re-implementingDhinakaran Pandiyan
intel_tile_dims() computes tile height using size and width, when there is already a function to do just that - intel_tile_height() Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-2-imre.deak@intel.com
2019-12-23drm/i915/selftests: make mock_drm.h self-containedJani Nikula
Needs i915_drv.h because i915 gets dereferenced. Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191219155652.2666-2-jani.nikula@intel.com
2019-12-23drm/i915/selftests: make mock_context.h self-containedJani Nikula
Fix the forward declaration. Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191219155652.2666-1-jani.nikula@intel.com
2019-12-23drm/i915: fix comment for POWER_DOMAIN_TRANSCODER_VDSC_PW2Jani Nikula
The power domain covers VDSC for DSI transcoder on ICL, and it's pedantically about pipe, not transcoder, on TGL. Reported-by: Vandita Kulkarni <vandita.kulkarni@intel.com> Cc: Vandita Kulkarni <vandita.kulkarni@intel.com> Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191219133845.9333-1-jani.nikula@intel.com
2019-12-22drm/i915/gt: Move pm debug files into a gt aware debugfsAndi Shyti
The GT system is becoming more and more a stand-alone system in i915 and it's fair to assign it its own debugfs directory. rc6, rps and llc debugfs files are gt related, move them into the gt debugfs directory. Signed-off-by: Andi Shyti <andi.shyti@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20191222144046.1674865-3-chris@chris-wilson.co.uk
2019-12-22drm/i915/gt: Merge engine init/setup loopsChris Wilson
Now that we don't need to create GEM contexts in the middle of engine construction, we can pull the engine init/setup loops together. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Andi Shyti <andi.shyti@intel.com> Reviewed-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191222144046.1674865-2-chris@chris-wilson.co.uk
2019-12-22drm/i915/gt: Pull intel_gt_init_hw() into intel_gt_resume()Chris Wilson
Since intel_gt_resume() is always immediately proceeded by init_hw, pull the call into intel_gt_resume, where we have the rpm and fw already held. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Andi Shyti <andi.shyti@intel.com> Reviewed-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191222144046.1674865-1-chris@chris-wilson.co.uk
2019-12-22drm/i915/gt: Pull GT initialisation under intel_gt_init()Chris Wilson
Begin pulling the GT setup underneath a single GT umbrella; let intel_gt take ownership of its engines! As hinted, the complication is the lifetime of the probed engine versus the active lifetime of the GT backends. We need to detect the engine layout early and keep it until the end so that we can sanitize state on takeover and release. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Andi Shyti <andi.shyti@intel.com> Acked-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191222120752.1368352-1-chris@chris-wilson.co.uk
2019-12-22drm/atomic: Spell CRTC consistentlyThierry Reding
CRTC is an abbreviation and should be all caps in prose. Update all kerneldoc comments to use a consistent spelling. v2: remove hunk unrelated to the CRTC spelling fixes Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191206135336.2084564-2-thierry.reding@gmail.com
2019-12-22drm: Fix a couple of typos, punctation and whitespace issuesThierry Reding
These are just a couple of things that I came across as I was reading through the code and comments. v2: added one more hunk that ended up in the wrong patch Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191206135336.2084564-1-thierry.reding@gmail.com
2019-12-21drm/i915: Move i915_gem_init_contexts() earlierChris Wilson
As the GEM global context setup is now independent of the GT state (although GT does currently still depend upon the global i915->kernel_context), we can move its init earlier, leaving the gt init ready to be extracted. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Andi Shyti <andi.shyti@intel.com> Reviewed-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221200109.1202310-1-chris@chris-wilson.co.uk
2019-12-21drm/i915/gt: Repeat wait_for_idle for retirement workersChris Wilson
Since we may retire timelines from secondary workers, intel_gt_retire_requests() is not always a reliable indicator that all pending retirements are complete. If we do detect secondary workers are in progress, recommend intel_gt_wait_for_idle() to repeat the retirement check. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221180204.1201217-1-chris@chris-wilson.co.uk
2019-12-21drm/i915: Remove i915->kernel_contextChris Wilson
Allocate only an internal intel_context for the kernel_context, forgoing a global GEM context for internal use as we only require a separate address space (for our own protection). Now having weaned GT from requiring ce->gem_context, we can stop referencing it entirely. This also means we no longer have to create random and unnecessary GEM contexts for internal use. GEM contexts are now entirely for tracking GEM clients, and intel_context the execution environment on the GPU. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Andi Shyti <andi.shyti@intel.com> Acked-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221160324.1073045-1-chris@chris-wilson.co.uk
2019-12-21drm/i915/selftests: Setup engine->retire for mock_engineChris Wilson
Enable and cleanup the engine->retire for the mock engine. Fixes: dc93c9b69315 ("drm/i915/gt: Schedule request retirement when signaler idles") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191221001136.720154-1-chris@chris-wilson.co.uk
2019-12-20drm/i915: Introduce intel_crtc_state_alloc()Ville Syrjälä
We have several places where we want to allocate a pristine crtc state. Some of those currently call intel_crtc_state_reset() to properly initialize all the non-zero defaults in the state, but some places do not. Let's add intel_crtc_state_alloc() to do both the alloc and the reset, and call that everywhere we need a fresh crtc state. v2: s/kzalloc/kmalloc/ since we memset() anyway (José) Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191219111430.17527-1-ville.syrjala@linux.intel.com Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
2019-12-20drm/stm: ltdc: move pinctrl to encoder mode setYannick Fertré
The pin control must be set to default as soon as possible to establish a good video link between tv & bridge hdmi (encoder mode set is call before encoder enable). Signed-off-by: Yannick Fertre <yannick.fertre@st.com> Acked-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/1574850218-13257-1-git-send-email-yannick.fertre@st.com
2019-12-20drm/i915/execlists: Select arb on/off around batches based on preemptionChris Wilson
Decide whether or not we need to disable arbitration within user batches based on our intel_engine_has_preemption() flag. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191213151331.1788371-1-chris@chris-wilson.co.uk
2019-12-20drm/i915: Push the use-semaphore marker onto the intel_contextChris Wilson
Instead of rummaging through the intel_context to peek at the GEM context in the middle of request submission to decide whether to use semaphores, store that information on the intel_context itself. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Andi Shyti <andi.shyti@intel.com> Reviewed-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191220101230.256839-2-chris@chris-wilson.co.uk
2019-12-20drm/i915: Drop GEM context as a direct link from i915_requestChris Wilson
Keep the intel_context as being the primary state for i915_request, with the GEM context a backpointer from the low level state for the rarer cases we need client information. Our goal is to remove such references to clients from the backend, and leave the HW submission agnostic to client interfaces and self-contained. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Andi Shyti <andi.shyti@intel.com> Reviewed-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191220101230.256839-1-chris@chris-wilson.co.uk
2019-12-20drm/i915/gt: Teach veng to defer the context allocationChris Wilson
Since we added the context_alloc callback to intel_context_ops, we can safely install a custom hook for the deferred virtual context allocation. This means that all new contexts behave the same upon creation, simplifying later code. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Andi Shyti <andi.shyti@intel.com> Reviewed-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191219232932.189197-1-chris@chris-wilson.co.uk
2019-12-19drm/i915/gt: Add breadcrumb retire to physical engineChris Wilson
Avoid adding the retire workers to the virtual engine so that we don't end up in the unenviable situation of trying to free the virtual engine while its worker remains active. Fixes: dc93c9b69315 ("drm/i915/gt: Schedule request retirement when signaler idles") Closes: https://gitlab.freedesktop.org/drm/intel/issues/867 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191219221344.161523-1-chris@chris-wilson.co.uk
2019-12-19drm/todo: Updating logging todoDaniel Vetter
Jani has merged a new set of logging functions, which we hope to be the One True solution now, pinky promises: commit fb6c7ab8718eb2543695d77ad8302ff81e8e1e32 Author: Jani Nikula <jani.nikula@intel.com> Date: Tue Dec 10 14:30:43 2019 +0200 drm/print: introduce new struct drm_device based logging macros Update the todo entry to match the new preference. v2: Fix spelling issue Sam noticed. Cc: Jani Nikula <jani.nikula@intel.com> Cc: Sean Paul <sean@poorly.run> Cc: Wambui Karuga <wambui.karugax@gmail.com> Acked-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191219161722.2779994-1-daniel.vetter@ffwll.ch
2019-12-19drm/i915: Rename pipe update tracepointsVille Syrjälä
All the other display related tracepoints use intel_ instead if i915_ as the prefix. Do the same for the pipe update tracepoints so I don't always have to spend time looking for them. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-6-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
2019-12-19drm/i915/fbc: Remove second redundant intel_fbc_pre_update() callVille Syrjälä
I fumbled the conflict resolution a bit when applying the fbc vblank wait w/a. Because of that we now call intel_fbc_pre_update() twice. Remove the second redundant call. Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-2-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
2019-12-19drm/i915/fbc: Reject PLANE_OFFSET.y%4!=0 on icl+ tooVille Syrjälä
icl and tgl are still affected by the modulo 4 PLANE_OFFSET.y underrun issue. Reject such configurations on all gen9+ platforms. Can be reproduced easily with the following sequence of hardware poking: while { write FBC_CTL.enable=1 wait for vblank write PLANE_OFFSET .x=0 .y=32 write PLANE_SURF wait for vblank # if PLANE_OFFSET.y is multiple of 4 the underrun won't happen write PLANE_OFFSET .x=0 .y=31 write PLANE_SURF wait for vblank # extra vblank wait is required here presumably # to get FBC into the proper state wait for vblank write FBC_CTL.enable=0 # underrun happens some time after FBC disable wait for vblank } Both 8888 and 565 pixel formats and all tilinga formats seem affected. Reproduced on KBL/GLK/ICL/TGL. BDW confirmed not affected. Closes: https://gitlab.freedesktop.org/drm/intel/issues/792 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-1-ville.syrjala@linux.intel.com Reviewed-by: Imre Deak <imre.deak@intel.com>
2019-12-19drm/i915: fix uninitialized pointer reads on pointers to and fromColin Ian King
Currently pointers to and from are not initialized and may contain garbage values. This will cause uninitialized pointer reads in the call to intel_frontbuffer_track and later checks to see if to and from are null. Fix this by ensuring to and from are initialized to NULL. Addresses-Coverity: ("Uninitialised pointer read)" Fixes: da42104f589d ("drm/i915: Hold reference to intel_frontbuffer as we track activity") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20191219190916.24693-1-colin.king@canonical.com
2019-12-19drm/i915/gt: Suppress threshold updates on RPS parkingChris Wilson
When we park RPS, we set the GPU to run at minimum 'idle' frequency. However, as the GPU is idle, we also disable the worker and RPS interrupts - changing the RPS thresholds has no effect, it just incurs extra changes to restore them when we unpark. So on parking, leave the thresholds set to the current power level and so we expect them to be valid for our restart. References: https://gitlab.freedesktop.org/drm/intel/issues/848 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Andi Shyti <andi.shyti@intel.com> Reviewed-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218210545.3975426-2-chris@chris-wilson.co.uk
2019-12-19drm/i915/gt: Use non-forcewake writes for RPSChris Wilson
Use non-forcewaked writes to queue RPS register changes that will take effect when the write buffer is flushed, rather than wake the mmio device for immediate effect. This is so that we can avoid a slow forcewake dance upon unparking, and at our irregular updates. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Andi Shyti <andi.shyti@intel.com> Reviewed-by: Andi Shyti <andi.shyti@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218210545.3975426-1-chris@chris-wilson.co.uk
2019-12-19drm/i915/gt: Track engine round-trip timesChris Wilson
Knowing the round trip time of an engine is useful for tracking the health of the system as well as providing a metric for the baseline responsiveness of the engine. We can use the latter metric for automatically tuning our waits in selftests and when idling so we don't confuse a slower system with a dead one. Upon idling the engine, we send one last pulse to switch the context away from precious user state to the volatile kernel context. We know the engine is idle at this point, and the pulse is non-preemptible, so this provides us with a good measurement of the round trip time. It also provides us with faster engine parking for ringbuffer submission, which is a welcome bonus (e.g. softer-rc6). Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Stuart Summers <stuart.summers@intel.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191219105043.4169050-1-chris@chris-wilson.co.uk Link: https://patchwork.freedesktop.org/patch/msgid/20191219124353.8607-2-chris@chris-wilson.co.uk
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-02 19:49:05 +0000