| Age | Commit message (Collapse) | Author |
|---|
|
This helps debugging when things go wrong.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
After the FW image was loaded for the first time,
fwrt->smem_cfg.num_lmacs value will no longer be zero since we don't
clean it when we stop the device. So if we load the image once and then
we fail on a consecutive attempt, the driver will abort any dumping.
Solve this by removing the condition. It is safe to remove since
when we do the actual dumping in iwl_fw_dbg_collect_sync we check
that STATUS_DEVICE_ENABLED bit is still active.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For non-offloaded rate control, implement VHT extended NSS
support by just ignoring 160 MHz on transmit if the peer
doesn't support the full NSS (2). This is pretty unlikely
and gets us 160 MHz RX as well as TX in most cases, since
the typical case for this workaround is 4x4 AP only doing
2x2 on 160 MHz.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When hostapd sends a probe response, it does not request an
acknowledgment on the probe response. This setting is propagated
to the driver and FW from mac80211, and as a result probe responses
are transmitted only once without retries. In congested
environments, this reduces the likelihood for finding the AP.
To overcome this, enable acknowledgment and retries for probe
responses, even in case no acknowledgment is requested. In such
a case the retry limit is set to 3.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no point in this, we already do everything in a nested
fashion, and if we didn't we'd already crash in iwl_mvm_leds_exit()
etc. Just remove the bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Previously the protection flag wasn't set on multicast frames even if
the RA is unicast. Fix this by checking addr1 instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add an option to not send beacons and probe responses. This is
used for testing multiple-bssid.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Return the AID currently set when reading this debugfs entry.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Verify we do not accept new beacon templates while beacon
injection is active.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We support this, so we should advertise it. In fact, if we don't,
mac80211 will do it for us (as we advertise SUPPORTS_VHT_EXT_NSS_BW
to it), but that requires a memory reallocation which is wasteful:
ieee80211 phy0: copying sband (band 1) due to VHT EXT NSS BW flag
Set the flag here to avoid that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The IWL_MVM_INIT_STATUS_REG_HW_INIT_COMPLETE bit shouldn't be set,
and realistically we should complete all setup before we call the
ieee80211_register_hw() function. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
With CONFIG_NO_AUTO_INLINE, we run into a silly warning when
gcc fails to remember that n_profiles is constant across
the function call to iwl_mvm_sar_set_profile:
drivers/net/wireless/intel/iwlwifi/mvm/fw.c: In function 'iwl_mvm_sar_get_ewrd_table':
drivers/net/wireless/intel/iwlwifi/mvm/fw.c:746:9: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Marking that function 'inline' avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In case mac80211 was requested to perform an HW restart, but the HW
restart has not started yet, there is no need to request another one.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
AX210 devices assume that the (DRAM) addresses of the rb_stts's for
the different queues are continuous.
So allocate the rb_stts's for all the Rx queues in one place.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
ath.git patches for 5.1. Major changes:
ath10k
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having
WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
|
|
The start() callback is too late for this: NetworkManager would already
have seen the hardware, thinking 00:00:00:00:00:00 is its permanent
address.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In order to be able to get a MAC address before we register the device
with ieee80211 we'll need to load the firmware way earlier.
There seems to be one problem with this: the device seems to start
with radio enabled and starts sending in frames right after the firmware
load finishes. Disable the radio as soon as possible.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We'll need to talk to the firmware to get a hardware address before
device is registered with ieee80211 subsystem at the end of
lbtf_add_card(). Hooking the callbacks after that is too late.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
While experimenting with firmware loading I ended up in a state of
firmware reporting shared RAM address 0x04000001. It was causing:
[ 94.448015] Unable to handle kernel paging request at virtual address cd680001
due to reading out of the mapped memory.
This patch adds some basic validation to avoid kernel crashes due to the
unexpected firmware behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There is an uppercase 'N' that should be a lowercase 'n', fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This recently added macro provides more meaningful error messages thanks
to identifying a specific wiphy. It's especially important on systems
with few cards supported by the same (brcmfmac) driver.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few last-minute fixes for 5.0.
The most significant one is the OF-node refcount fix for ASoC
simple-card, which could be triggered on many boards. Another fix for
ASoC core is for the error handling in topology, while others are
device-specific fixes for Samsung and HD-audio"
* tag 'sound-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: simple-card: fixup refcount_t underflow
ASoC: topology: free created components in tplg load error
ALSA: hda/realtek: Disable PC beep in passthrough on alc285
ALSA: hda/realtek - Headset microphone and internal speaker support for System76 oryp5
ASoC: samsung: i2s: Fix prescaler setting for the secondary DAI
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some final pin control fixes (I hope) to round off the v5.0 pin
control development cycle.
Only driver fixes, one for stable:
- Meson8B fixup for the sdc pins
- Fix SDC tile position for Qualcomm QCS404"
* tag 'pinctrl-v5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: meson: meson8b: fix the sdxc_a data 1..3 pins
pinctrl: qcom: qcs404: Correct SDC tile
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two GPIO fixes for the v5.0 series:
- Per-instance irqchip on the MT7621
- Avoid direction setting using pin control on MMP2"
* tag 'gpio-v5.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pxa: avoid attempting to set pin direction via pinctrl on MMP2
gpio: MT7621: use a per instance irq_chip structure
|
|
Pull MTD fixes from Boris Brezillon:
- Don't add a digit to MTD-backed nvmem device names
- Make sure powernv flash names are unique
* tag 'mtd/fixes-for-5.0-rc8' of git://git.infradead.org/linux-mtd:
mtd: powernv_flash: Fix device registration error
mtd: Use mtd->name when registering nvmem device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull keys fixes from James Morris:
- Handle quotas better, allowing full quota to be reached.
- Fix the creation of shortcuts in the assoc_array internal
representation when the index key needs to be an exact multiple of
the machine word size.
- Fix a dependency loop between the request_key contruction record and
the request_key authentication key. The construction record isn't
really necessary and can be dispensed with.
- Set the timestamp on a new key rather than leaving it as 0. This
would ordinarily be fine - provided the system clock is never set to
a time before 1970
* 'fixes-v5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
keys: Timestamp new keys
keys: Fix dependency loop between construction record and auth key
assoc_array: Fix shortcut creation
KEYS: allow reaching the keys quotas exactly
|
|
Commit 482997699ef0 ("ARM: tegra: Fix unit_address_vs_reg DTC warnings
for /memory") inadventently broke device tree ABI by adding a unit-
address to the "/memory" node because the device tree compiler flagged
the missing unit-address as a warning.
Tegra124 Chromebooks (a.k.a. Nyan) use a bootloader that relies on the
full name of the memory node in device tree being exactly "/memory". It
can be argued whether this was a good decision or not, and some other
bootloaders (such as U-Boot) do accept a unit-address in the name of the
node, but the device tree is an ABI and we can't break existing setups
just because the device tree compiler considers it bad practice to omit
the unit-address nowadays.
This partially reverts the offending commit and restores device tree ABI
compatibility.
Fixes: 482997699ef0 ("ARM: tegra: Fix unit_address_vs_reg DTC warnings for /memory")
Reported-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Updates to the GIC architecture allow ID_AA64PFR0_EL1.GIC to have
values other than 0 or 1. At the moment, Linux is quite strict in the
way it handles this field at early boot stage (cpufeature is fine) and
will refuse to use the system register CPU interface if it doesn't
find the value 1.
Fixes: 021f653791ad17e03f98aaa7fb933816ae16f161 ("irqchip: gic-v3: Initial support for GICv3")
Reported-by: Chase Conklin <Chase.Conklin@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
If we skipped all the connectors that were not part of a tile, we would
leave conn_seq=0 and conn_configured=0, convincing ourselves that we
had stagnated in our configuration attempts. Avoid this situation by
starting conn_seq=ALL_CONNECTORS, and repeating until we find no more
connectors to configure.
Fixes: 754a76591b12 ("drm/i915/fbdev: Stop repeating tile configuration on stagnation")
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190215123019.32283-1-chris@chris-wilson.co.uk
Cc: <stable@vger.kernel.org> # v3.19+
(cherry picked from commit d9b308b1f8a1acc0c3279f443d4fe0f9f663252e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Two easily resolvable overlapping change conflicts, one in
TCP and one in the eBPF verifier.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f56 ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes checkpatch warnings:
Prefer 'unsigned long' over 'unsigned long int' as the int is unnecessary
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pull networking fixes from David Miller:
1) Fix suspend and resume in mt76x0u USB driver, from Stanislaw
Gruszka.
2) Missing memory barriers in xsk, from Magnus Karlsson.
3) rhashtable fixes in mac80211 from Herbert Xu.
4) 32-bit MIPS eBPF JIT fixes from Paul Burton.
5) Fix for_each_netdev_feature() on big endian, from Hauke Mehrtens.
6) GSO validation fixes from Willem de Bruijn.
7) Endianness fix for dwmac4 timestamp handling, from Alexandre Torgue.
8) More strict checks in tcp_v4_err(), from Eric Dumazet.
9) af_alg_release should NULL out the sk after the sock_put(), from Mao
Wenan.
10) Missing unlock in mac80211 mesh error path, from Wei Yongjun.
11) Missing device put in hns driver, from Salil Mehta.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
sky2: Increase D3 delay again
vhost: correctly check the return value of translate_desc() in log_used()
net: netcp: Fix ethss driver probe issue
net: hns: Fixes the missing put_device in positive leg for roce reset
net: stmmac: Fix a race in EEE enable callback
qed: Fix iWARP syn packet mac address validation.
qed: Fix iWARP buffer size provided for syn packet processing.
r8152: Add support for MAC address pass through on RTL8153-BD
mac80211: mesh: fix missing unlock on error in table_path_del()
net/mlx4_en: fix spelling mistake: "quiting" -> "quitting"
net: crypto set sk to NULL when af_alg_release.
net: Do not allocate page fragments that are not skb aligned
mm: Use fixed constant in page_frag_alloc instead of size + 1
tcp: tcp_v4_err() should be more careful
tcp: clear icsk_backoff in tcp_write_queue_purge()
net: mv643xx_eth: disable clk on error path in mv643xx_eth_shared_probe()
qmi_wwan: apply SET_DTR quirk to Sierra WP7607
net: stmmac: handle endianness in dwmac4_get_timestamp
doc: Mention MSG_ZEROCOPY implementation for UDP
mlxsw: __mlxsw_sp_port_headroom_set(): Fix a use of local variable
...
|
|
Another platform requires even longer delay to make the device work
correctly after S3.
So increase the delay to 300ms.
BugLink: https://bugs.launchpad.net/bugs/1798921
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Passing the struct ptp_clock_info caps by parameter is passing over 130 bytes
of data by value on the stack. Optimize this by passing it by reference instead.
Also shinks the object code size:
Before:
text data bss dec hex filename
12596 2160 64 14820 39e4 drivers/ptp/ptp_qoriq.o
After:
text data bss dec hex filename
12567 2160 64 14791 39c7 drivers/ptp/ptp_qoriq.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When disabling vport, relevant vport configurations will be cleaned
up. These cleanups should be done to the vports which had these configs
applied at vport enablement. As esw manager vport didn't have such
vport config applied, cleanup should not touch it.
Fixes: de9e6a8136c5 ("net/mlx5: E-Switch, Properly refer to host PF vport as other vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reported-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When eswitch gets vport data structure, the index should not be out
of the range of the vport array. Driver mistakenly used vport number
to check the range.
Fixes: 22b8ddc86bf4 ("net/mlx5: E-Switch, Assign a different position for uplink rep and vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix the following compiler warning:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:2770:
warning: unused variable ‘esw’ [-Wunused-variable]
Fixes: 1cd3ab86b713 ("net/mlx5e: Introduce mlx5e_flow_esw_attr_init() helper")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
fpga_qpn was assigned but never used and compilation with W=1
produced the following warning:
drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c: In function _mlx5_fpga_event_:
drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c:320:6: warning:
variable _fpga_qpn_ set but not used [-Wunused-but-set-variable]
u32 fpga_qpn;
^~~~~~~~
Fixes: 98db16bab59f ("net/mlx5: FPGA, Handle QP error event")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Compilation with W=1 produces following warning:
drivers/net/ethernet/mellanox/mlx5/core/en/monitor_stats.c:69:6:
warning: no previous prototype for _mlx5e_monitor_counter_start_ [-Wmissing-prototypes]
void mlx5e_monitor_counter_start(struct mlx5e_priv *priv)
^~~~~~~~~~~~~~~~~~~~~~~~~~~
Avoid it by declaring mlx5e_monitor_counter_start() as a static function.
Fixes: 5c7e8bbb0257 ("net/mlx5e: Use monitor counters for update stats")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch is a little improvement. Simplify the mlx5e_tc_add_fdb_flow().
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Introduce the mlx5e_flow_esw_attr_init() helper
for simplifying codes.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
With recent introduction of flow_rule infrastructure drivers no longer
directly include action headers, so it is no longer possible to use
constants defined in them. Instead, one of flow_rule patches substituted
pedit action header constant with hardcoded value '2' in mlx5
set_pedit_val() function conditional which verifies that header type is in
range of values allowed by pedit action. That conditional is now both
wrong (hardcoded value is '2' but __PEDIT_HDR_TYPE_MAX is 6 in current
version) and superfluous (pedit action already verifies that header type is
in allowed range during init). Remove the described check from mlx5 code.
Fixes: 738678817573 ("drivers: net: use flow action infrastructure")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Take into a function the common code structure of opening
a side set of channels followed by a call to apply them.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In previous patch, driver added new speed modes: 50Gbps per lane support
for 50G/100G/200G. This patch modifies mlx5e_get_link_ksettings and
mlx5e_set_link_ksettings to set and get these link modes via ethtool.
In order to do so, added mapping of new HW bits to ethtool bitmap and
enforce mutual exclusion between extended link modes and previously
defined link modes.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
