| Age | Commit message (Collapse) | Author |
|---|
|
GENET has historically had to create a MDIO platform device for its
controller and pass some auxiliary data to it, like a MDIO completion
callback. Now we also pass the "main" clock to allow for the MDIO bus
controller to manage that clock adequately around I/O accesses.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now we have managed not to have the mdio-bcm-unimac manage its
clock except during probe and suspend/resume. This works most of the
time, except where it does not.
With a fully modular build, we can get into a situation whereby the
GENET driver is fully registered, and so is the mdio-bcm-unimac driver,
however the Ethernet PHY driver is not yet, because it depends on a
resource that is not yet available (e.g.: GPIO provider). In that state,
the network device is not usable yet, and so to conserve power, the
GENET driver will have turned off its "main" clock which feeds its MDIO
controller.
When the PHY driver finally probes however, we make an access to the PHY
registers to e.g.: disable interrupts, and this causes a bus error
within the MDIO controller space because the MDIO controller clock(s)
are turned off.
To remedy that, we manage the clock around all of the I/O accesses to
the hardware which are done exclusively during read, write and clock
divider configuration.
This ensures that the register space is accessible, and this also
ensures that there are not unnecessarily elevated reference counts
keeping the clocks active when the network device is administratively
turned off. It would be the case with the previous way of managing the
clock.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit [1] added framer support under drivers/net/wan,
which is covered by NETWORKING [GENERAL]. And it is implied
that framer-provider.h and framer.h, which were also added
buy the same patch, are also maintained as part of NETWORKING [GENERAL].
Make this explicit by adding these files to the corresponding
section in MAINTAINERS.
[1] 82c944d05b1a ("net: wan: Add framer framework support")
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove documentation of non-existent children field
from the Kernel doc for struct framer_ops.
Introduced by 82c944d05b1a ("net: wan: Add framer framework support")
Signed-off-by: Simon Horman <horms@kernel.org>
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported another task hung in __unix_gc(). [0]
The current while loop assumes that all of the left candidates
have oob_skb and calling kfree_skb(oob_skb) releases the remaining
candidates.
However, I missed a case that oob_skb has self-referencing fd and
another fd and the latter sk is placed before the former in the
candidate list. Then, the while loop never proceeds, resulting
the task hung.
__unix_gc() has the same loop just before purging the collected skb,
so we can call kfree_skb(oob_skb) there and let __skb_queue_purge()
release all inflight sockets.
[0]:
Sending NMI from CPU 0 to CPUs 1:
NMI backtrace for cpu 1
CPU: 1 PID: 2784 Comm: kworker/u4:8 Not tainted 6.8.0-rc4-syzkaller-01028-g71b605d32017 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
Workqueue: events_unbound __unix_gc
RIP: 0010:__sanitizer_cov_trace_pc+0x0/0x70 kernel/kcov.c:200
Code: 89 fb e8 23 00 00 00 48 8b 3d 84 f5 1a 0c 48 89 de 5b e9 43 26 57 00 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 <f3> 0f 1e fa 48 8b 04 24 65 48 8b 0d 90 52 70 7e 65 8b 15 91 52 70
RSP: 0018:ffffc9000a17fa78 EFLAGS: 00000287
RAX: ffffffff8a0a6108 RBX: ffff88802b6c2640 RCX: ffff88802c0b3b80
RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000000000
RBP: ffffc9000a17fbf0 R08: ffffffff89383f1d R09: 1ffff1100ee5ff84
R10: dffffc0000000000 R11: ffffed100ee5ff85 R12: 1ffff110056d84ee
R13: ffffc9000a17fae0 R14: 0000000000000000 R15: ffffffff8f47b840
FS: 0000000000000000(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffef5687ff8 CR3: 0000000029b34000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<NMI>
</NMI>
<TASK>
__unix_gc+0xe69/0xf40 net/unix/garbage.c:343
process_one_work kernel/workqueue.c:2633 [inline]
process_scheduled_works+0x913/0x1420 kernel/workqueue.c:2706
worker_thread+0xa5f/0x1000 kernel/workqueue.c:2787
kthread+0x2ef/0x390 kernel/kthread.c:388
ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1b/0x30 arch/x86/entry/entry_64.S:242
</TASK>
Reported-and-tested-by: syzbot+ecab4d36f920c3574bf9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ecab4d36f920c3574bf9
Fixes: 25236c91b5ab ("af_unix: Fix task hung while purging oob_skb in GC.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.9
The second "new features" pull request for v6.9. Lots of iwlwifi and
stack changes this time. And naturally smaller changes to other drivers.
We also twice merged wireless into wireless-next to avoid conflicts
between the trees.
Major changes:
stack
* mac80211: negotiated TTLM request support
* SPP A-MSDU support
* mac80211: wider bandwidth OFDMA config support
iwlwifi
* kunit tests
* bump FW API to 89 for AX/BZ/SC devices
* enable SPP A-MSDUs
* support for new devices
ath12k
* refactoring in preparation for Multi-Link Operation (MLO) support
* 1024 Block Ack window size support
* provide firmware wmi logs via a trace event
ath11k
* 36 bit DMA mask support
* support 6 GHz station power modes: Low Power Indoor (LPI), Standard
Power) SP and Very Low Power (VLP)
rtl8xxxu
* TP-Link TL-WN823N V2 support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kunwu Chan says:
====================
net: Use KMEM_CACHE instead of kmem_cache_create
As Jiri Pirko suggests,
I'm using a patchset to cleanup the same issues in the 'net' module.
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create
to simplify the creation of SLAB caches.
Some cache names are changed to be the same as struct names.
This change is recorded in the changelog for easy reference.
It's harmless cause it's used in /proc/slabinfo to identify this cache.
---
Changes in v2:
- Delete a patch as Eric said in https://lore.kernel.org/all/CANn89iLkWvum6wSqSya_K+1eqnFvp=L2WLW=kAYrZTF8Ei4b7g@mail.gmail.com/
- No code changes,only add Reviewed-by tag
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create
to simplify the creation of SLAB caches.
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create
to simplify the creation of SLAB caches.
And change cache name from 'ip_dst_cache' to 'rtable'.
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create
to simplify the creation of SLAB caches.
And change cache name from 'ip_mrt_cache' to 'mfc_cache'.
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create
to simplify the creation of SLAB caches.
And change cache name from 'ip6_mrt_cache' to 'mfc6_cache'.
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create
to simplify the creation of SLAB caches.
And change cache name from 'kcm_mux_cache' to 'kcm_mux',
'kcm_psock_cache' to 'kcm_psock'.
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In newer hardware, IPA supports more than 32 endpoints. Some
registers--such as IPA interrupt registers--represent endpoints
as bits in a 4-byte register, and such registers are repeated as
needed to represent endpoints beyond the first 32.
In ipa_interrupt_suspend_clear_all(), we clear all pending IPA
suspend interrupts by reading all status register(s) and writing
corresponding registers to clear interrupt conditions.
Unfortunately the number of registers to read/write is calculated
incorrectly, and as a result we access *many* more registers than
intended. This bug occurs only when the IPA hardware signals a
SUSPEND interrupt, which happens when a packet is received for an
endpoint (or its underlying GSI channel) that is suspended. This
situation is difficult to reproduce, but possible.
Fix this by correctly computing the number of interrupt registers to
read and write. This is the only place in the code where registers
that map endpoints or channels this way perform this calculation.
Fixes: f298ba785e2d ("net: ipa: add a parameter to suspend registers")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported a lockdep violation [1] involving af_unix
support of SO_PEEK_OFF.
Since SO_PEEK_OFF is inherently not thread safe (it uses a per-socket
sk_peek_off field), there is really no point to enforce a pointless
thread safety in the kernel.
After this patch :
- setsockopt(SO_PEEK_OFF) no longer acquires the socket lock.
- skb_consume_udp() no longer has to acquire the socket lock.
- af_unix no longer needs a special version of sk_set_peek_off(),
because it does not lock u->iolock anymore.
As a followup, we could replace prot->set_peek_off to be a boolean
and avoid an indirect call, since we always use sk_set_peek_off().
[1]
WARNING: possible circular locking dependency detected
6.8.0-rc4-syzkaller-00267-g0f1dd5e91e2b #0 Not tainted
syz-executor.2/30025 is trying to acquire lock:
ffff8880765e7d80 (&u->iolock){+.+.}-{3:3}, at: unix_set_peek_off+0x26/0xa0 net/unix/af_unix.c:789
but task is already holding lock:
ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1691 [inline]
ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: sockopt_lock_sock net/core/sock.c:1060 [inline]
ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: sk_setsockopt+0xe52/0x3360 net/core/sock.c:1193
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (sk_lock-AF_UNIX){+.+.}-{0:0}:
lock_acquire+0x1e3/0x530 kernel/locking/lockdep.c:5754
lock_sock_nested+0x48/0x100 net/core/sock.c:3524
lock_sock include/net/sock.h:1691 [inline]
__unix_dgram_recvmsg+0x1275/0x12c0 net/unix/af_unix.c:2415
sock_recvmsg_nosec+0x18e/0x1d0 net/socket.c:1046
____sys_recvmsg+0x3c0/0x470 net/socket.c:2801
___sys_recvmsg net/socket.c:2845 [inline]
do_recvmmsg+0x474/0xae0 net/socket.c:2939
__sys_recvmmsg net/socket.c:3018 [inline]
__do_sys_recvmmsg net/socket.c:3041 [inline]
__se_sys_recvmmsg net/socket.c:3034 [inline]
__x64_sys_recvmmsg+0x199/0x250 net/socket.c:3034
do_syscall_64+0xf9/0x240
entry_SYSCALL_64_after_hwframe+0x6f/0x77
-> #0 (&u->iolock){+.+.}-{3:3}:
check_prev_add kernel/locking/lockdep.c:3134 [inline]
check_prevs_add kernel/locking/lockdep.c:3253 [inline]
validate_chain+0x18ca/0x58e0 kernel/locking/lockdep.c:3869
__lock_acquire+0x1345/0x1fd0 kernel/locking/lockdep.c:5137
lock_acquire+0x1e3/0x530 kernel/locking/lockdep.c:5754
__mutex_lock_common kernel/locking/mutex.c:608 [inline]
__mutex_lock+0x136/0xd70 kernel/locking/mutex.c:752
unix_set_peek_off+0x26/0xa0 net/unix/af_unix.c:789
sk_setsockopt+0x207e/0x3360
do_sock_setsockopt+0x2fb/0x720 net/socket.c:2307
__sys_setsockopt+0x1ad/0x250 net/socket.c:2334
__do_sys_setsockopt net/socket.c:2343 [inline]
__se_sys_setsockopt net/socket.c:2340 [inline]
__x64_sys_setsockopt+0xb5/0xd0 net/socket.c:2340
do_syscall_64+0xf9/0x240
entry_SYSCALL_64_after_hwframe+0x6f/0x77
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(sk_lock-AF_UNIX);
lock(&u->iolock);
lock(sk_lock-AF_UNIX);
lock(&u->iolock);
*** DEADLOCK ***
1 lock held by syz-executor.2/30025:
#0: ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1691 [inline]
#0: ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: sockopt_lock_sock net/core/sock.c:1060 [inline]
#0: ffff8880765e7930 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: sk_setsockopt+0xe52/0x3360 net/core/sock.c:1193
stack backtrace:
CPU: 0 PID: 30025 Comm: syz-executor.2 Not tainted 6.8.0-rc4-syzkaller-00267-g0f1dd5e91e2b #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1e7/0x2e0 lib/dump_stack.c:106
check_noncircular+0x36a/0x4a0 kernel/locking/lockdep.c:2187
check_prev_add kernel/locking/lockdep.c:3134 [inline]
check_prevs_add kernel/locking/lockdep.c:3253 [inline]
validate_chain+0x18ca/0x58e0 kernel/locking/lockdep.c:3869
__lock_acquire+0x1345/0x1fd0 kernel/locking/lockdep.c:5137
lock_acquire+0x1e3/0x530 kernel/locking/lockdep.c:5754
__mutex_lock_common kernel/locking/mutex.c:608 [inline]
__mutex_lock+0x136/0xd70 kernel/locking/mutex.c:752
unix_set_peek_off+0x26/0xa0 net/unix/af_unix.c:789
sk_setsockopt+0x207e/0x3360
do_sock_setsockopt+0x2fb/0x720 net/socket.c:2307
__sys_setsockopt+0x1ad/0x250 net/socket.c:2334
__do_sys_setsockopt net/socket.c:2343 [inline]
__se_sys_setsockopt net/socket.c:2340 [inline]
__x64_sys_setsockopt+0xb5/0xd0 net/socket.c:2340
do_syscall_64+0xf9/0x240
entry_SYSCALL_64_after_hwframe+0x6f/0x77
RIP: 0033:0x7f78a1c7dda9
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 e1 20 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f78a0fde0c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000036
RAX: ffffffffffffffda RBX: 00007f78a1dac050 RCX: 00007f78a1c7dda9
RDX: 000000000000002a RSI: 0000000000000001 RDI: 0000000000000006
RBP: 00007f78a1cca47a R08: 0000000000000004 R09: 0000000000000000
R10: 0000000020000180 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000000006e R14: 00007f78a1dac050 R15: 00007ffe5cd81ae8
Fixes: 859051dd165e ("bpf: Implement cgroup sockaddr hooks for unix sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Daan De Meyer <daan.j.demeyer@gmail.com>
Cc: Kuniyuki Iwashima <kuniyu@amazon.com>
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With commit 34d21de99cea9 ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core instead
of this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Move dummy driver to leverage the core allocation.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
AF reserves MCAM entries for each PF, VF present in the
system and populates the entry with DMAC and action with
default RSS so that basic packet I/O works. Since PF/VF is
not aware of the RSS action installed by AF, AF only fixup
the actions of the rules installed by PF/VF with corresponding
default RSS action. This worked well for rules installed by
PF/VF for features like RX VLAN offload and DMAC filters but
rules involving action like drop/forward to queue are also
getting modified by AF. Hence fix it by setting the default
RSS action only if requested by PF/VF.
Fixes: 967db3529eca ("octeontx2-af: add support for multicast/promisc packet replication feature")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of ethtool_adv_to_mmd_eee_adv_t() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code overwrites fields in tp->eee with unchecked data from
edata, e.g. the bitmap with supported modes. ethtool properly returns
the received data from get_eee() call, but we have no guarantee that
other users of the ioctl set_eee() interface behave properly too.
Therefore copy only fields which are actually needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct xt_entry_target fake flexible array has not be converted to a
true flexible array, which is mainly blocked by it being both UAPI and
used in the middle of other structures. In order to properly check for
0-sized destinations in memcpy(), an exception must be made for the one
place where it is still a destination. Since memcpy() was already
skipping checks for 0-sized destinations, using unsafe_memcpy() is no
change in behavior.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
No need to keep this in the core, move it to the nfnetlink_queue module.
nf_reroute is moved too, there were no other callers.
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
An earlier attempt changed this to GFP_KERNEL, but the get helper is
also called for get requests from userspace, which uses rcu.
Let the caller pass in the kmalloc flags to allow insertions
to schedule if needed.
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Insertions into the set are slow when we try to add many elements.
For 800k elements I get:
time nft -f pipapo_800k
real 19m34.849s
user 0m2.390s
sys 19m12.828s
perf stats:
--95.39%--nft_pipapo_insert
|--76.60%--pipapo_insert
| --76.37%--pipapo_resize
| |--72.87%--memcpy_orig
| |--1.88%--__free_pages_ok
| | --0.89%--free_tail_page_prepare
| --1.38%--kvmalloc_node
..
--18.56%--pipapo_get.isra.0
|--13.91%--__bitmap_and
|--3.01%--pipapo_refill
|--0.81%--__kmalloc
| --0.74%--__kmalloc_large_node
| --0.66%--__alloc_pages
..
--0.52%--memset_orig
So lots of time is spent in copying exising elements to make space for
the next one.
Instead of allocating to the exact size of the new rule count, allocate
extra slack to reduce alloc/copy/free overhead.
After:
time nft -f pipapo_800k
real 1m54.110s
user 0m2.515s
sys 1m51.377s
--80.46%--nft_pipapo_insert
|--73.45%--pipapo_get.isra.0
|--57.63%--__bitmap_and
| |--8.52%--pipapo_refill
|--3.45%--__kmalloc
| --3.05%--__kmalloc_large_node
| --2.58%--__alloc_pages
--2.59%--memset_orig
|--6.51%--pipapo_insert
--5.96%--pipapo_resize
|--3.63%--memcpy_orig
--2.13%--kvmalloc_node
The new @rules_alloc fills a hole, so struct size doesn't go up.
Also make it so rule removal doesn't shrink unless the free/extra space
exceeds two pages. This should be safe as well:
When a rule gets removed, the attempt to lower the allocated size is
already allowed to fail.
Exception: do exact allocations as long as set is very small (less
than one page needed).
v2: address comments from Stefano:
kdoc comment
formatting changes
remove redundant assignment
switch back to PAGE_SIZE
Link: https://lore.kernel.org/netfilter-devel/20240213141753.17ef27a6@elisabeth/
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
The set uses a mix of 'int', 'unsigned int', and size_t.
The rule count limit is NFT_PIPAPO_RULE0_MAX, which cannot
exceed INT_MAX (a few helpers use 'int' as return type).
Add a compile-time assertion for this.
Replace size_t usage in structs with unsigned int or u8 where
the stored values are smaller.
Replace signed-int arguments for lengths with 'unsigned int'
where possible.
Last, remove lt_aligned member: its set but never read.
struct nft_pipapo_match 40 bytes -> 32 bytes
struct nft_pipapo_field 56 bytes -> 32 bytes
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
pipapo relies on kmalloc(0) returning ZERO_SIZE_PTR (i.e., not NULL
but pointer is invalid).
Rework this to not call slab allocator when we'd request a 0-byte
allocation.
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Those get called from packet path, content must not be modified.
No functional changes intended.
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Randy Dunlap reports arptables build failure:
arp_tables.c:(.text+0x20): undefined reference to `xt_find_table'
... because recent change removed a 'select' on the xtables core.
Add a "depends" clause on arptables to resolve this.
Kernel test robot reports another build breakage:
iptable_nat.c:(.text+0x8): undefined reference to `ipt_unregister_table_exit'
... because of a typo, the nat table selected ip6tables.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/netfilter-devel/d0dfbaef-046a-4c42-9daa-53636664bf6d@infradead.org/
Fixes: a9525c7f6219 ("netfilter: xtables: allow xtables-nft only builds")
Fixes: 4654467dc7e1 ("netfilter: arptables: allow xtables-nft only builds")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Remove useless branch to check for errors in nft_parse_register_store().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Sanitize nf_logger_find_get() input parameters, no caller in the tree
passes invalid values.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Consolidate pointer fetch to logger and check for NULL in
__find_logger().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
nf_conntrack_expect_init
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create
to simplify the creation of SLAB caches.
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.8, take #3
- Check for the validity of interrupts handled by a MOVALL
command
- Check for the validity of interrupts while reading the
pending state on enabling LPIs.
|
|
It is possible that an LPI mapped in a different ITS gets unmapped while
handling the MOVALL command. If that is the case, there is no state that
can be migrated to the destination. Silently ignore it and continue
migrating other LPIs.
Cc: stable@vger.kernel.org
Fixes: ff9c114394aa ("KVM: arm/arm64: GICv4: Handle MOVALL applied to a vPE")
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240221092732.4126848-3-oliver.upton@linux.dev
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
vgic_get_irq() may not return a valid descriptor if there is no ITS that
holds a valid translation for the specified INTID. If that is the case,
it is safe to silently ignore it and continue processing the LPI pending
table.
Cc: stable@vger.kernel.org
Fixes: 33d3bc9556a7 ("KVM: arm64: vgic-its: Read initial LPI pending table")
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240221092732.4126848-2-oliver.upton@linux.dev
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Ricardo B. Marliere says:
====================
net: constify struct device_type usage
This is a simple and straight forward cleanup series that makes all device
types in the net subsystem constants. This has been possible since 2011 [1]
but not all occurrences were cleaned. I have been sweeping the tree to fix
them all.
I was not sure if I should send these squashed, but there are quite a few
changes so I decided to send them separately. Please let me know if that is
not desirable.
[1] https://lore.kernel.org/all/1305850262-9575-5-git-send-email-gregkh@suse.de/
====================
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the hso_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the wwan_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the
nsim_bus_dev_type variable to be a constant structure as well, placing it
into read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the vlan_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the l2tpeth_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the hsr_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the geneve_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the ppp_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the vxlan_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the br_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the dsa_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the wlan_type
and wwan_type variables to be constant structures as well, placing it into
read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The xlate callbacks are supposed to translate of_phandle_args to proper
provider without modifying the of_phandle_args. Make the argument
pointer to const for code safety and readability.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240217100306.86740-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the missing MODULE_FIRMWARE entry for RTL8126A.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/47ef79d2-59c4-4d44-9595-366c70c4ad87@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Properly check page pointer returned by page_pool_dev_alloc routine in
skb_pp_cow_data() for non-linear part of the original skb.
Reported-by: Julian Wiedmann <jwiedmann.dev@gmail.com>
Closes: https://lore.kernel.org/netdev/cover.1707729884.git.lorenzo@kernel.org/T/#m7d189b0015a7281ed9221903902490c03ed19a7a
Fixes: e6d5dbdd20aa ("xdp: add multi-buff support for xdp running in generic mode")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/r/25512af3e09befa9dcb2cf3632bdc45b807cf330.1708167716.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull rdma fixes from Jason Gunthorpe:
"Mostly irdma and bnxt_re fixes:
- Missing error unwind in hf1
- For bnxt - fix fenching behavior to work on new chips, fail
unsupported SRQ resize back to userspace, propogate SRQ FW failure
back to userspace.
- Correctly fail unsupported SRQ resize back to userspace in bnxt
- Adjust a memcpy in mlx5 to not overflow a struct field.
- Prevent userspace from triggering mlx5 fw syndrome logging from
sysfs
- Use the correct access mode for MLX5_IB_METHOD_DEVX_OBJ_MODIFY to
avoid a userspace failure on modify
- For irdma - Don't UAF a concurrent tasklet during destroy, prevent
userspace from issuing invalid QP attrs, fix a possible CQ
overflow, capture a missing HW async error event
- sendmsg() triggerable memory access crash in hfi1
- Fix the srpt_service_guid parameter to not crash due to missing
function pointer
- Don't leak objects in error unwind in qedr
- Don't weirdly cast function pointers in srpt"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/srpt: fix function pointer cast warnings
RDMA/qedr: Fix qedr_create_user_qp error flow
RDMA/srpt: Support specifying the srpt_service_guid parameter
IB/hfi1: Fix sdma.h tx->num_descs off-by-one error
RDMA/irdma: Add AE for too many RNRS
RDMA/irdma: Set the CQ read threshold for GEN 1
RDMA/irdma: Validate max_send_wr and max_recv_wr
RDMA/irdma: Fix KASAN issue with tasklet
RDMA/mlx5: Relax DEVX access upon modify commands
IB/mlx5: Don't expose debugfs entries for RRoCE general parameters if not supported
RDMA/mlx5: Fix fortify source warning while accessing Eth segment
RDMA/bnxt_re: Add a missing check in bnxt_qplib_query_srq
RDMA/bnxt_re: Return error for SRQ resize
RDMA/bnxt_re: Fix unconditional fence for newer adapters
RDMA/bnxt_re: Remove a redundant check inside bnxt_re_vf_res_config
RDMA/bnxt_re: Avoid creating fence MR for newer adapters
IB/hfi1: Fix a memleak in init_credit_return
|
