summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-05-15spi: spi-rockchip: add support for spi slave modeChris Ruehl
Add support for spi slave mode in spi-rockchip. The register map has an entry for it. If spi-slave is set in dts, set this corresponding bit and add to mode_bits the SPI_NO_CS, allow slave mode without explicit CS use. Slave abort function had been added. Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Link: https://lore.kernel.org/r/20200511083022.23678-3-chris.ruehl@gtsys.com.hk Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-15spi: spi-rockchip: cleanup use struct spi_controllerChris Ruehl
Cleanup, move from the compatibily layer struct spi_master over to struct spi_controller, and rename the related function calls. Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Link: https://lore.kernel.org/r/20200511083022.23678-2-chris.ruehl@gtsys.com.hk Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-15spi: dw: Clear DMAC register when done or stoppedSerge Semin
If DMAC register is left uncleared any further DMAless transfers may cause the DMAC hardware handshaking interface getting activated. So the next DMA-based Rx/Tx transaction will be started right after the dma_async_issue_pending() method is invoked even if no DMATDLR/DMARDLR conditions are met. This at the same time may cause the Tx/Rx FIFO buffers underrun/overrun. In order to fix this we must clear DMAC register after a current DMA-based transaction is finished. Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200515104758.6934-4-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-15spi: dw: Initialize paddr in DW SPI MMIO private dataSerge Semin
This field is used only for the DW SPI DMA code initialization, that's why there were no problems with it being uninitialized in Dw SPI MMIO driver. Since in a further patch we are going to introduce the DW SPI DMA support in the MMIO version of the driver, lets set the field with the physical address of the DW SPI controller registers region. Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200515104758.6934-12-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-15spi: dw: Fix native CS being unsetSerge Semin
Commit 6e0a32d6f376 ("spi: dw: Fix default polarity of native chipselect") attempted to fix the problem when GPIO active-high chip-select is utilized to communicate with some SPI slave. It fixed the problem, but broke the normal native CS support. At the same time the reversion commit ada9e3fcc175 ("spi: dw: Correct handling of native chipselect") didn't solve the problem either, since it just inverted the set_cs() polarity perception without taking into account that CS-high might be applicable. Here is what is done to finally fix the problem. DW SPI controller demands any native CS being set in order to proceed with data transfer. So in order to activate the SPI communications we must set any bit in the Slave Select DW SPI controller register no matter whether the platform requests the GPIO- or native CS. Preferably it should be the bit corresponding to the SPI slave CS number. But currently the dw_spi_set_cs() method activates the chip-select only if the second argument is false. Since the second argument of the set_cs callback is expected to be a boolean with "is-high" semantics (actual chip-select pin state value), the bit in the DW SPI Slave Select register will be set only if SPI core requests the driver to set the CS in the low state. So this will work for active-low GPIO-based CS case, and won't work for active-high CS setting the bit when SPI core actually needs to deactivate the CS. This commit fixes the problem for all described cases. So no matter whether an SPI slave needs GPIO- or native-based CS with active-high or low signal the corresponding bit will be set in SER. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Fixes: ada9e3fcc175 ("spi: dw: Correct handling of native chipselect") Fixes: 6e0a32d6f376 ("spi: dw: Fix default polarity of native chipselect") Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20200515104758.6934-5-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-12spi: dw: Drop duplicate error message when remap resourceAndy Shevchenko
devm_platform_ioremap_resource() will issue a message in the error case. Thus, no need to duplicate in the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200512110315.58845-1-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-12spi: Convert UniPhier SPI controller to json-schemaKunihiko Hayashi
Convert UniPhier SPI controller binding to DT schema format. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/1587720562-15293-1-git-send-email-hayashi.kunihiko@socionext.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-11spi: dw-mmio: Do not add acpi modalias when CONFIG_ACPI is not enabledJay Fang
Reduce unnecessary static memory allocation when CONFIG_ACPI is not enabled. Signed-off-by: Jay Fang <f.fangjian@huawei.com> Link: https://lore.kernel.org/r/1588991392-24219-1-git-send-email-f.fangjian@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-11spi: sun6i: Add support for GPIO chip select linesAlistair Francis
Set use_gpio_descriptors as true to support using generic GPIO lines for the chip select. Signed-off-by: Alistair Francis <alistair@alistair23.me> Link: https://lore.kernel.org/r/20200511045330.690507-1-alistair@alistair23.me Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-11spi: uniphier: Use devm_platform_get_and_ioremap_resource() to simplify codeKunihiko Hayashi
Use devm_platform_get_and_ioremap_resource() to simplify code instead of platform_get_resource() and devm_ioremap_resource(). This also gets the resource that the following code uses. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Link: https://lore.kernel.org/r/1589185530-28170-2-git-send-email-hayashi.kunihiko@socionext.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-11spi: uniphier: Depend on HAS_IOMEMKunihiko Hayashi
The driver uses devm_ioremap_resource() which is only available when CONFIG_HAS_IOMEM is set, so the driver depends on this option. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Link: https://lore.kernel.org/r/1589185530-28170-1-git-send-email-hayashi.kunihiko@socionext.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-07spi: dw: Get rid of dma_inited flagAndy Shevchenko
This flag is superfluous in all cases where it's being used, i.e. * ->can_dma() won't be called without dma_inited == 1 * DMA ->exit() callback can rely on txchan and rxchan variables So, get rid of dma_inited flag. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200507115449.8093-2-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-07spi: dw: Avoid useless assignments in generic DMA setupAndy Shevchenko
Generic DMA setup doesn't rely on certain type of DMA controller and thus shouldn't use Intel Medfield settings, although it's harmless in this case. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200507115449.8093-1-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-06spi: dw: Add Elkhart Lake PSE DMA supportJarkko Nikula
Elkhart Lake PSE SPI is capable to utilize PSE DMA engine which is described in ACPI. With help of acpi-dma module the support becomes a generic one. Thus, add Elkhart Lake PSE DMA support and generic DMA hooks in SPI DesignWare driver. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200506153025.21441-8-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-06spi: dw: Propagate struct device pointer to ->dma_init() callbackAndy Shevchenko
In some cases, one of which is coming soon, we would like to have a struct device pointer to request DMA channel. For this purpose propagate it to ->dma_init() callback in DMA ops. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200506153025.21441-7-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-06spi: dw: Add 'mfld' suffix to Intel Medfield related routinesAndy Shevchenko
In order to prepare driver for the extension to support newer hardware, add 'mfld' suffix to some related functions. While here, move DMA parameters assignment under existing #ifdef CONFIG_SPI_DW_MID_DMA. There is no functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200506153025.21441-6-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-06spi: dw: Move few headers under #ifdef CONFIG_SPI_DW_MID_DMAAndy Shevchenko
There is no user of few headers without CONFIG_SPI_DW_MID_DMA being set. Move them under condition. While at it, remove unused slab.h there. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200506153025.21441-5-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-06spi: dw: Downgrade interrupt.h to irqreturn.h where appropriateAndy Shevchenko
spi-dw-mid.c along with spi-dw.h are direct users of irqreturn.h and nothing else is being used from interrupt.h. So, switch them to use the former instead of latter one. While here, move the header under #ifdef CONFIG_SPI_DW_MID_DMA in spi-dw-mid.c. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200506153025.21441-4-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-06spi: dw: Move interrupt.h to spi-dw.h who is user of itAndy Shevchenko
The actual user of interrupt.h is spi-dw.h and not bus drivers. Move header there. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200506153025.21441-3-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-06spi: dw: Remove unused variable in CR0 configuring hooksAndy Shevchenko
After enabling new IP support in the driver couple of variables were left unused compiler is not happy about: .../spi-dw.c: In function ‘dw_spi_update_cr0’: .../spi-dw.c:264:17: warning: unused variable ‘dws’ [-Wunused-variable] 264 | struct dw_spi *dws = spi_controller_get_devdata(master); | ^~~ .../spi-dw.c: In function ‘dw_spi_update_cr0_v1_01a’: .../spi-dw.c:285:17: warning: unused variable ‘dws’ [-Wunused-variable] 285 | struct dw_spi *dws = spi_controller_get_devdata(master); | ^~~ Drop them for good. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200506153025.21441-2-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-06spi: dw: Zero DMA Tx and Rx configurations on stackAndy Shevchenko
Some DMA controller drivers do not tolerate non-zero values in the DMA configuration structures. Zero them to avoid issues with such DMA controller drivers. Even despite above this is a good practice per se. Fixes: 7063c0d942a1 ("spi/dw_spi: add DMA support") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Feng Tang <feng.tang@intel.com> Cc: Feng Tang <feng.tang@intel.com> Link: https://lore.kernel.org/r/20200506153025.21441-1-andriy.shevchenko@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-06spi: bcm2835: Fix error return code in bcm2835_dma_init()Wei Yongjun
Fix to return negative error code -ENOMEM from the dma mapping error handling case instead of 0, as done elsewhere in this function. Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20200506125607.90952-1-weiyongjun1@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-06spi: a3700: make a3700_spi_init() return voidJason Yan
Fix the following coccicheck warning: drivers/spi/spi-armada-3700.c:283:8-11: Unneeded variable: "ret". Return "0" on line 315 Signed-off-by: Jason Yan <yanaijie@huawei.com> Link: https://lore.kernel.org/r/20200506061911.19923-1-yanaijie@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-05spi: dw-apb-ssi: Add Intel Keem Bay supportWan Ahmad Zainie
Document Intel Keem Bay SPI controller DT bindings. Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Link: https://lore.kernel.org/r/20200505130618.554-7-wan.ahmad.zainie.wan.mohamad@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-05spi: dw-apb-ssi: Add compatible string for DesignWare DWC_ssiWan Ahmad Zainie
This patch adds compatible string "snps,dwc-ssi-1.01a" to the above DT binding document, to provide support for DesignWare DWC_ssi IP [1]. Current driver supports DW_apb_ssi IP [2]. References: [1] https://www.synopsys.com/dw/ipdir.php?c=dwc_ssi [2] https://www.synopsys.com/dw/ipdir.php?c=DW_apb_ssi Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Link: https://lore.kernel.org/r/20200505130618.554-5-wan.ahmad.zainie.wan.mohamad@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-05spi: dw: Add support for Intel Keem Bay SPIWan Ahmad Zainie
Add support for Intel Keem Bay SPI controller, which uses DesignWare DWC_ssi core. Bit 31 of CTRLR0 register is added for Keem Bay, to configure the device as a master or as a slave serial peripheral. Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200505130618.554-6-wan.ahmad.zainie.wan.mohamad@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-05spi: dw: Add support for DesignWare DWC_ssiWan Ahmad Zainie
This patch adds initial support for DesignWare DWC_ssi soft IP. DWC_ssi is the enhanced version of DW_apb_ssi, which is currently supported by this driver. Their registers are same, but the bit fields of register CTRLR0 are different. DWC_ssi has additional features compared to DW_apb_ssi. Major enhancements in DWC_ssi are hyper bus protocol, boot mode support and advanced XIP support. DWC_ssi is an AHB slave device, whilst DW_apb_ssi is an APB slave device. Register offset DW_ssi DW_apb_ssi CTRLR0 0x00 0x00 CTRLR1 0x04 0x04 SSIENR 0x08 0x08 MWCR 0x0c 0x0c SER 0x10 0x10 BAUDR 0x14 0x14 TXFTLR 0x18 0x18 RXFTLR 0x1c 0x1c TXFLR 0x20 0x20 RXFLR 0x24 0x24 SR 0x28 0x28 IMR 0x2c 0x2c ISR 0x30 0x30 RISR 0x34 0x34 TXOICR 0x38 0x38 RXOICR 0x3c 0x3c RXUICR 0x40 0x40 MSTICR 0x44 0x44 ICR 0x48 0x48 DMACR 0x4c 0x4c DMATDLR 0x50 0x50 DMARDLR 0x54 0x54 IDR 0x58 0x58 SSI_VERSION_ID 0x5c 0x5c DRx (0 to 35) 0x60+i*0x4 0x60+i*0x4 RX_SAMPLE_DLY 0xf0 0xf0 SPI_CTRLR0 0xf4 0xf4 TXD_DRIVE_EDGE 0xf8 0xf8 XIP_MODE_BITS 0xfc RSVD Register configuration - CTRLR0 DW_ssi DW_apb_ssi SPI_HYPERBUS_EN bit[24] NONE SPI_FRF bit[23:22] bit[22:21] DFS_32 NONE bit[20:16] CFS bit[19:16] bit[15:12] SSTE bit[14] bit[24] SRL bit[13] bit[11] SLV_OE bit[12] bit[10] TMOD bit[11:10] bit[9:8] SCPOL | SPHA bit[9:8] bit[7:6] FRF bit[7:6] bit[5:4] DFS bit[4:0] bit[3:0] The documents used are [1] DW_apb_ssi_databook.pdf version 4.01a (2016.10a). [2] DWC_ssi_databook.pdf version 1.01a. Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200505130618.554-4-wan.ahmad.zainie.wan.mohamad@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-05spi: dw: Add update_cr0() callback to update CTRLR0Wan Ahmad Zainie
This patch adds update_cr0() callback, in struct dw_spi. Existing code that configure register CTRLR0 is moved into a new function, dw_spi_update_cr0(), and this will be the default. Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200505130618.554-3-wan.ahmad.zainie.wan.mohamad@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-05spi: dw: Fix typo in few registers nameWan Ahmad Zainie
This patch will fix typo in the register name used in the source code, to be consistent with the register name used in the databook. Databook: DW_apb_ssi_databook.pdf version 4.01a Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200505130618.554-2-wan.ahmad.zainie.wan.mohamad@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-05spi: bcm2835: Fixes bare use of unsignedJacko Dirks
Signed-off-by: Jacko Dirks <jdirks.linuxdev@gmail.com> Link: https://lore.kernel.org/r/20200503200033.GA3256@vasteMachine Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-05Merge series "Grab bag with AMD SPI fixes" from Lukas Wunner <lukas@wunner.de>:Mark Brown
Here's an assortment of drive-by fixes for the new AMD SPI driver. All of them are compile-tested only. Lukas Wunner (5): spi: amd: Fix duplicate iounmap in error path spi: amd: Pass probe errors back to driver core spi: amd: Drop duplicate driver data assignments spi: amd: Fix refcount underflow on remove spi: amd: Drop superfluous member from struct amd_spi drivers/spi/spi-amd.c | 27 +++++---------------------- 1 file changed, 5 insertions(+), 22 deletions(-) -- 2.26.2
2020-05-05Merge branch 'for-5.7' of ↵Mark Brown
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-5.8
2020-05-04spi: amd: Drop superfluous member from struct amd_spiLukas Wunner
The AMD SPI driver stores a pointer to the spi_master in struct amd_spi so that it can get from the latter to the former in amd_spi_fifo_xfer(). It's simpler to just pass the pointer from the sole caller amd_spi_master_transfer() and drop the pointer from struct amd_spi. Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/a088b684ad292faf3bd036e51529e608e5c94638.1588590210.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-04spi: amd: Fix refcount underflow on removeLukas Wunner
The AMD SPI driver calls spi_master_put() in its ->remove() hook even though the preceding call to spi_unregister_master() already drops a ref, thus leading to a refcount underflow. Drop the superfluous call to spi_master_put(). This only leaves the call to spi_unregister_master() in the ->remove() hook, so it's safe to change the ->probe() hook to use the devm version of spi_register_master() and drop the ->remove() hook altogether. Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/5e53ccdf1eecd4e015dba99d0d77389107f8a2e3.1588590210.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-04spi: amd: Drop duplicate driver data assignmentsLukas Wunner
The AMD SPI driver calls platform_set_drvdata() on probe even though it's already been set by __spi_alloc_controller(). Likewise, it calls platform_set_drvdata() on remove even though it's going to be set by __device_release_driver(). Drop the duplicate assignments. Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/499f8ad4759c2ff0f586e0459fb9a293faecff6d.1588590210.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-04spi: amd: Pass probe errors back to driver coreLukas Wunner
If probing fails, the AMD SPI driver pretends success to the driver core by returning 0. Return the errno instead. Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/689f29a359718dab4f5de9ee66c02ea97b3bd9e8.1588590210.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-04spi: amd: Fix duplicate iounmap in error pathLukas Wunner
The AMD SPI driver uses devm_ioremap_resource() to map its registers, so they're automatically unmapped via device_release() when the last ref on the SPI controller is dropped. The additional iounmap() in the ->probe() error path is thus unnecessary. Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/497cc38ae2beb7900ae05a1463eb83ff96e2770e.1588590210.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org>
2020-04-30spi: atmel: Add missing annotation for atmel_spi_next_xfer_dma_submit()Jules Irenge
Sparse reports a warning at atmel_spi_next_xfer_dma_submit() warning: context imbalance in atmel_spi_next_xfer_dma_submit() - unexpected unlock The root cause is the missing annotation at atmel_spi_next_xfer_dma_submit() Add the missing __must_hold(&as->lock) annotation Signed-off-by: Jules Irenge <jbi.octave@gmail.com> Link: https://lore.kernel.org/r/20200429225723.31258-3-jbi.octave@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-04-30spi: pxa2xx: Apply CS clk quirk to BXTEvan Green
With a couple allies at Intel, and much badgering, I got confirmation from Intel that at least BXT suffers from the same SPI chip-select issue as Cannonlake (and beyond). The issue being that after going through runtime suspend/resume, toggling the chip-select line without also sending data does nothing. Add the quirk to BXT to briefly toggle dynamic clock gating off and on, forcing the fabric to wake up enough to notice the CS register change. Signed-off-by: Evan Green <evgreen@chromium.org> Cc: Shobhit Srivastava <shobhit.srivastava@intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200427163238.1.Ib1faaabe236e37ea73be9b8dcc6aa034cb3c8804@changeid Signed-off-by: Mark Brown <broonie@kernel.org>
2020-04-29spi: stm32-qspi: Fix unbalanced pm_runtime_enable issuePatrice Chotard
Issue detected by unbinding/binding the stm32 qspi driver as following: root@stm32mp2:~# echo 40430000.spi > /sys/bus/platform/drivers/stm32-qspi/404300 00.spi/driver/unbind root@stm32mp2:~# echo 40430000.spi > /sys/bus/platform/drivers/stm32-qspi/bind [ 969.864021] stm32-qspi 40430000.spi: Unbalanced pm_runtime_enable! [ 970.225161] spi-nor spi0.0: mx66u51235f (65536 Kbytes) [ 970.935721] spi-nor spi0.1: mx66u51235f (65536 Kbytes) Fixes: 9d282c17b023 ("spi: stm32-qspi: Add pm_runtime support") Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Link: https://lore.kernel.org/r/20200429102625.25974-1-patrice.chotard@st.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-04-29spi: uniphier: fix error return code in uniphier_spi_probe()Wei Yongjun
Fix to return negative error code -EPROBE_DEFER from the DMA probe defer error handling case instead of 0, as done elsewhere in this function. Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20200429075855.104487-1-weiyongjun1@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-04-29spi: spi-amd: Fix a NULL vs IS_ERR() check in amd_spi_probe()Wei Yongjun
In case of error, the function devm_ioremap_resource() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Fixes: bbb336f39efc ("spi: spi-amd: Add AMD SPI controller driver support") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20200429025426.167664-1-weiyongjun1@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-04-28spi: spi-amd: fix warningSanjay R Mehta
remove unused variable "opcode" Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com> Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/1588049801-37995-1-git-send-email-sanju.mehta@amd.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-04-27spi: spi-amd: Add AMD SPI controller driver supportSanjay R Mehta
This driver supports SPI Controller for AMD SOCs.This driver supports SPI operations using FIFO mode of transfer. Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com> Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/1587844788-33997-1-git-send-email-sanju.mehta@amd.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-04-27Merge tag 'v5.7-rc3' into spi-5.8Mark Brown
Linux 5.7-rc3
2020-04-26Linux 5.7-rc3v5.7-rc3Linus Torvalds
2020-04-26Merge tag '5.7-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6Linus Torvalds
Pull cifs fixes from Steve French: "Five cifs/smb3 fixes:two for DFS reconnect failover, one lease fix for stable and the others to fix a missing spinlock during reconnect" * tag '5.7-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6: cifs: fix uninitialised lease_key in open_shroot() cifs: ensure correct super block for DFS reconnect cifs: do not share tcons with DFS cifs: minor update to comments around the cifs_tcp_ses_lock mutex cifs: protect updating server->dstaddr with a spinlock
2020-04-26Merge tag 'usb-5.7-rc3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg KH: "Here are a number of USB driver fixes for 5.7-rc3. Nothing huge, just the usual collection of: - xhci fixes - gadget driver fixes - syzkaller fuzzing fixes - new device ids and DT bindings - new quirks added for broken devices A few of the gadget driver fixes show up twice here as they were applied to my branch, and also by Felipe to his branch which I then pulled in as we got out of sync a bit. All of these have been in linux-next with no reported issues" * tag 'usb-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits) USB: sisusbvga: Change port variable from signed to unsigned usb-storage: Add unusual_devs entry for JMicron JMS566 USB: hub: Revert commit bd0e6c9614b9 ("usb: hub: try old enumeration scheme first for high speed devices") USB: hub: Fix handling of connect changes during sleep usb: typec: altmode: Fix typec_altmode_get_partner sometimes returning an invalid pointer xhci: Don't clear hub TT buffer on ep0 protocol stall xhci: prevent bus suspend if a roothub port detected a over-current condition xhci: Fix handling halted endpoint even if endpoint ring appears empty usb: raw-gadget: Fix copy_to/from_user() checks usb: raw-gadget: fix raw_event_queue_fetch locking usb: gadget: udc: atmel: Fix vbus disconnect handling usb: dwc3: gadget: Fix request completion check USB: Add USB_QUIRK_DELAY_CTRL_MSG and USB_QUIRK_DELAY_INIT for Corsair K70 RGB RAPIDFIRE phy: tegra: Select USB_COMMON for usb_get_maximum_speed() usb: typec: tcpm: Ignore CC and vbus changes in PORT_RESET change usb: f_fs: Clear OS Extended descriptor counts to zero in ffs_data_reset() cdc-acm: introduce a cool down cdc-acm: close race betrween suspend() and acm_softint UAS: fix deadlock in error handling and PM flushing work UAS: no use logging any details in case of ENODEV ...
2020-04-26Merge tag 'tty-5.7-rc3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial fixes from Greg KH: "Here are some tty and serial driver fixes for 5.7-rc3. The "largest" in here are a number of reverts for previous changes to the uartps serial driver that turned out to not be a good idea at all. The others are just small fixes found by people and tools. Included in here is a much-reported symbol export needed by previous changes that happened in 5.7-rc1. All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: tty: hvc: fix buffer overflow during hvc_alloc(). tty: rocket, avoid OOB access tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart vt: don't hardcode the mem allocation upper bound tty: serial: owl: add "much needed" clk_prepare_enable() vt: don't use kmalloc() for the unicode screen buffer tty/sysrq: Export sysrq_mask(), sysrq_toggle_support() serial: sh-sci: Make sure status register SCxSR is read in correct sequence serial: sunhv: Initialize lock for non-registered console Revert "serial: uartps: Register own uart console and driver structures" Revert "serial: uartps: Move Port ID to device data structure" Revert "serial: uartps: Change uart ID port allocation" Revert "serial: uartps: Do not allow use aliases >= MAX_UART_INSTANCES" Revert "serial: uartps: Fix error path when alloc failed" Revert "serial: uartps: Use the same dynamic major number for all ports" Revert "serial: uartps: Fix uartps_major handling"
2020-04-26Merge tag 'char-misc-5.7-rc3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver fixes from Greg KH: "Here are 4 small misc driver fixes for 5.7-rc3: - mei driver fix - interconnect driver fix - two fpga driver fixes All have been in linux-next with no reported issues" * tag 'char-misc-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: interconnect: qcom: Fix uninitialized tcs_cmd::wait mei: me: fix irq number stored in hw struct fpga: dfl: pci: fix return value of cci_pci_sriov_configure fpga: zynq: Remove clk_get error message for probe defer
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-31 13:57:30 +0000