| Age | Commit message (Collapse) | Author |
|---|
|
The NXP ENETC is a 4-port Ethernet controller which 'smells' to
operating systems like 4 distinct PCIe PFs with SR-IOV, each PF having
its own driver instance, but in fact there are some hardware resources
which are shared between all ports, like for example the 256 KB SRAM
FIFO between the MACs and the Host Transfer Agent which DMAs frames to
DRAM.
To hide the stuff that cannot be neatly exposed per port, the hardware
designers came up with this idea of having a dedicated register block
which is supposed to be populated by the bootloader, and contains
everything configuration-related: MAC addresses, FIFO partitioning, etc.
When a port is reset using PCIe Function Level Reset, its defaults are
transferred from the IERB configuration. Most of the time, the settings
made through the IERB are read-only in the port's memory space (if they
are even visible), so they cannot be modified at runtime.
Linux doesn't have any advanced FIFO partitioning requirements at all,
but when reading through the hardware manual, it became clear that, even
though there are many good 'recommendations' for default values, many of
them were not actually put in practice on LS1028A. So we end up with a
default configuration that:
(a) does not have enough TX and RX byte credits to support the max MTU
of 9600 (which the Linux driver claims already) properly (at full speed)
(b) allows the FIFO to be overrun with RX traffic, potentially
overwriting internal data structures.
The last part sounds a bit catastrophic, but it isn't. Frames are
supposed to transit the FIFO for a very short time, but they can
actually accumulate there under 2 conditions:
(a) there is very severe congestion on DRAM memory, or
(b) the RX rings visible to the operating system were configured for
lossless operation, and they just ran out of free buffers to copy
the frame to. This is what is used to put backpressure onto the MAC
with flow control.
So since ENETC has not supported flow control thus far, RX FIFO overruns
were never seen with Linux. But with the addition of flow control, we
should configure some registers to prevent this from happening. What we
are trying to protect against are bad actors which continue to send us
traffic despite the fact that we have signaled a PAUSE condition. Of
course we can't be lossless in that case, but it is best to configure
the FIFO to do tail dropping rather than letting it overrun.
So in a nutshell, this driver is a fixup for all the IERB default values
that should have been but aren't.
The IERB configuration needs to be done _before_ the PFs are enabled.
So every PF searches for the presence of the "fsl,ls1028a-enetc-ierb"
node in the device tree, and if it finds it, it "registers" with the
IERB, which means that it requests the IERB to fix up its default
values. This is done through -EPROBE_DEFER. The IERB driver is part of
the fsl_enetc module, but is technically a platform driver, since the
IERB is a good old fashioned MMIO region, as opposed to ENETC ports
which pretend to be PCIe devices.
The driver was already configuring ENETC_PTXMBAR (FIFO allocation for
TX) because due to an omission, TXMBAR is a read/write register in the
PF memory space. But the manual is quite clear that the formula for this
should depend upon the TX byte credits (TXBCR). In turn, the TX byte
credits are only readable/writable through the IERB. So if we want to
ensure that the TXBCR register also has a value that is correct and in
line with TXMBAR, there is simply no way this can be done from the PF
driver, access to the IERB is needed.
I could have modified U-Boot to fix up the IERB values, but that is
quite undesirable, as old U-Boot versions are likely to be floating
around for quite some time from now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mention the required compatible string and base address for the
Integrated Endpoint Register Block node.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even though ENETC interfaces are exposed as individual PCIe PFs with
their own driver instances, the ENETC is still fundamentally a
multi-port Ethernet controller, and some parts of the IP take a port
number (as can be seen in the PSFP implementation).
Create a common helper that can be used outside of the TSN code for
retrieving the ENETC port number based on the PF number. This is only
correct for LS1028A, the only Linux-capable instantiation of ENETC thus
far.
Note that ENETC port 3 is PF 6. The TSN code did not care about this
because ENETC port 3 does not support TSN, so the wrong mapping done by
enetc_get_port for PF 6 could have never been hit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following out-of-bounds warning:
net/ethtool/ioctl.c:492:2: warning: 'memcpy' offset [49, 84] from the object at 'link_usettings' is out of the bounds of referenced subobject 'base' with type 'struct ethtool_link_settings' at offset 0 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
some struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &link_usettings.base. Fix this by directly
using &link_usettings and _from_ as destination and source addresses,
instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a VF driver for Microsoft Azure Network Adapter (MANA) that will be
available in the future.
Co-developed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Co-developed-by: Shachar Raindel <shacharr@microsoft.com>
Signed-off-by: Shachar Raindel <shacharr@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some prototypes are unnecessary, so delete it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel says:
====================
nexthop: Support large scale nexthop flushing
Patch #1 fixes a day-one bug in the nexthop code and allows "ip nexthop
flush" to work correctly with large number of nexthops that do not fit
in a single-part dump.
Patch #2 adds a test case.
Targeting at net-next since this use case never worked, the flow is
pretty obscure and such a large number of nexthops is unlikely to be
used in any real-world scenario.
Tested with fib_nexthops.sh:
Tests passed: 219
Tests failed: 0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test that all the nexthops are flushed when a multi-part nexthop dump is
required for the flushing.
Without previous patch:
# ./fib_nexthops.sh
TEST: Large scale nexthop flushing [FAIL]
With previous patch:
# ./fib_nexthops.sh
TEST: Large scale nexthop flushing [ OK ]
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, a multi-part nexthop dump is restarted based on the number of
nexthops that have been dumped so far. This can result in a lot of
nexthops not being dumped when nexthops are simultaneously deleted:
# ip nexthop | wc -l
65536
# ip nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 36040 nexthops
# ip nexthop | wc -l
29496
Instead, restart the dump based on the nexthop identifier (fixed number)
of the last successfully dumped nexthop:
# ip nexthop | wc -l
65536
# ip nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 65536 nexthops
# ip nexthop | wc -l
0
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Tested-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.13
Second set of patches for v5.13. A lot of iwlwifi and mt76 patches
this time, and also smaller features and fixes all over.
mt76
* mt7915/mt7615 decapsulation offload support
* threaded NAPI support
* new device IDs
* mt7921 device reset support
* rx timestamp support
iwlwifi
* passive scan support for 6GHz
* new hardware support
wilc1000
* CRC support for SPI bus
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we overflow the maximum number of BSS entries and free the
new entry, drop it from any hidden_list that it may have been
added to in the code above or in cfg80211_combine_bsses().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20210416094212.5de7d1676ad7.Ied283b0bc5f504845e7d6ab90626bdfa68bb3dc0@changeid
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the HE capabilities, spell A-MSDU correctly, not "A-MDSU".
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.9e6ff1af1181.If6868bc6902ccd9a95c74c78f716c4b41473ef14@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The A-MPDU length exponent extension is defined differently in
802.11ax D6.1, align with that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.c2a257d3e2df.I3455245d388c52c61dace7e7958dbed7e807cfb6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some names were changed, align that with the spec as of
802.11ax-D6.1.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.b1e5fbab0d8c.I3eb6076cb0714ec6aec6b8f9dee613ce4a05d825@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Don't bother keeping the link in that case. It is way
too complicated to keep the connection.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.a126c8833398.I677bdac314dd50d90474a90593902c17f9410cc4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Draft P802.11ax_D2.5 defines the following capabilities that
can be negotiated using RSNXE capabilities:
- Secure LTF measurement exchange protocol.
- Secure RTT measurement exchange protocol.
- Management frame protection for all management frames exchanged
during the negotiation and range measurement procedure.
Extend the nl80211 API to allow drivers to declare support for
these new capabilities as part of extended feature.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.8280e31d8091.Ifcb29f84f432290338f80c8378aa5c9e0a390c93@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case the frequency is invalid, ieee80211_parse_ch_switch_ie
will fail and we may not even reach the check in
ieee80211_sta_process_chanswitch. Drop the connection
in case ieee80211_parse_ch_switch_ie failed, but still
take into account the CSA mode to remember not to send
a deauth frame in case if it is forbidden to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.34712ef96a0a.I75d7ad7f1d654e8b0aa01cd7189ff00a510512b3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This will allow the low level driver to get the wdev during
the add_interface flow.
In order to do that, remove a few checks from there and do
not return NULL for vifs that were not yet added to the
driver. Note that all the current callers of this helper
function assume that the vif already exists:
- The callers from the drivers already have a vif pointer.
Before this change, ieee80211_vif_to_wdev would return NULL
in some cases, but those callers don't even check they
get a non-NULL pointer from ieee80211_vif_to_wdev.
- The callers from net/mac80211/cfg.c assume the vif is
already added to the driver as well.
So, this change has no impact on existing callers of this
helper function.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.6078d3517095.I1907a45f267a62dab052bcc44428aa7a2005ffc9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a flag that indicates that the ISTA shall indicate support for
LMR feedback in NDP ranging negotiation.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.eff546283504.I2606161e700ac24d94d0b50c8edcdedd4c0395c2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add an enum with the values of the ranging parameters max LTF total
field, as defined in IEEE802.11az_D2.6, table Table 9-322h23fc.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.d2588ebb1974.I9424c8ade13c4c938cb9999d8ce99d0d4c1cc198@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As crypto_shash_setkey() can fail, we should check the return value.
Addresses-Coverity-ID: 1401813 ("Unchecked return value")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.533ff7acf1d2.I034bafa201c4a6823333f8410aeaa60cca5ee9e0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The increment of idx is indented one level too deeply, clean up the
code by removing the extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210416095137.2033469-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
My previous commit to not apply flow control to management frames
that are going over TXQs (which is currently only the case for
iwlwifi, I think) broke things, with iwlwifi firmware crashing on
certain frames. As it turns out, that was due to the frame being
too short: space for the MIC wasn't added at the end of encrypted
management frames.
Clearly, this is due to using the 'frags' queue - this is meant
only for frames that have already been processed for TX, and the
code in ieee80211_tx_dequeue() just returns them. This caused all
management frames to now not get any TX processing.
To fix this, use IEEE80211_TX_INTCFL_NEED_TXPROCESSING (which is
currently used only in other circumstances) to indicate that the
frames need processing, and clear it immediately after so that,
at least in theory, MMPDUs can be fragmented.
Fixes: 73bc9e0af594 ("mac80211: don't apply flow control on management frames")
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210416134702.ef8486a64293.If0a9025b39c71bb91b11dd6ac45547aba682df34@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It's not modified so make it const with the eventual goal of moving
data to text for various static struct ieee80211_rate arrays.
Signed-off-by: Joe Perches <joe@perches.com>
Link: https://lore.kernel.org/r/8b210b5f5972e39eded269b35a1297cf824c4181.camel@perches.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix multiple kernel-doc warnings in cfg80211.h.
cfg80211.h:363: warning: missing initial short description on line:
* struct ieee80211_sband_iftype_data
cfg80211.h:6743: warning: missing initial short description on line:
* cfg80211_vendor_cmd_get_sender
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210417060142.1648-1-rdunlap@infradead.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The htmldoc produces this warning which was introduced
bu the commit below.
include/net/cfg80211.h:6643: warning: expecting prototype for wiphy_rfkill_set_hw_state().
Prototype was for wiphy_rfkill_set_hw_state_reason() instead
Fixes: 6f779a66dc84 ("cfg80211: allow specifying a reason for hw_rfkill")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210413113850.59098-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch adds the .offload_stats operation to synchronize hardware
stats with the expression data. Update the counter expression to use
this new interface. The hardware stats are retrieved from the netlink
dump path via FLOW_CLS_STATS command to the driver.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Test that packets are correctly routed when netfilter mangling rules are
present.
Without previous patch:
# ./fib_tests.sh -t ipv4_mangle
IPv4 mangling tests
TEST: Connection with correct parameters [ OK ]
TEST: Connection with incorrect parameters [ OK ]
TEST: Connection with correct parameters - mangling [FAIL]
TEST: Connection with correct parameters - no mangling [ OK ]
TEST: Connection check - server side [FAIL]
Tests passed: 3
Tests failed: 2
# ./fib_tests.sh -t ipv6_mangle
IPv6 mangling tests
TEST: Connection with correct parameters [ OK ]
TEST: Connection with incorrect parameters [ OK ]
TEST: Connection with correct parameters - mangling [FAIL]
TEST: Connection with correct parameters - no mangling [ OK ]
TEST: Connection check - server side [FAIL]
Tests passed: 3
Tests failed: 2
With previous patch:
# ./fib_tests.sh -t ipv4_mangle
IPv4 mangling tests
TEST: Connection with correct parameters [ OK ]
TEST: Connection with incorrect parameters [ OK ]
TEST: Connection with correct parameters - mangling [ OK ]
TEST: Connection with correct parameters - no mangling [ OK ]
TEST: Connection check - server side [ OK ]
Tests passed: 5
Tests failed: 0
# ./fib_tests.sh -t ipv6_mangle
IPv6 mangling tests
TEST: Connection with correct parameters [ OK ]
TEST: Connection with incorrect parameters [ OK ]
TEST: Connection with correct parameters - mangling [ OK ]
TEST: Connection with correct parameters - no mangling [ OK ]
TEST: Connection check - server side [ OK ]
Tests passed: 5
Tests failed: 0
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Netfilter tries to reroute mangled packets as a different route might
need to be used following the mangling. When this happens, netfilter
does not populate the IP protocol, the source port and the destination
port in the flow key. Therefore, FIB rules that match on these fields
are ignored and packets can be misrouted.
Solve this by dissecting the outer flow and populating the flow key
before rerouting the packet. Note that flow dissection only happens when
FIB rules that match on these fields are installed, so in the common
case there should not be a penalty.
Reported-by: Michal Soltys <msoltyspl@yandex.pl>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The nftables offload parser sets FLOW_DISSECTOR_KEY_BASIC .n_proto to the
ethertype field in the ethertype frame. However:
- FLOW_DISSECTOR_KEY_BASIC .n_proto field always stores either IPv4 or IPv6
ethertypes.
- FLOW_DISSECTOR_KEY_VLAN .vlan_tpid stores either the 802.1q and 802.1ad
ethertypes. Same as for FLOW_DISSECTOR_KEY_CVLAN.
This function adjusts the flow dissector to handle two scenarios:
1) FLOW_DISSECTOR_KEY_VLAN .vlan_tpid is set to 802.1q or 802.1ad.
Then, transfer:
- the .n_proto field to FLOW_DISSECTOR_KEY_VLAN .tpid.
- the original FLOW_DISSECTOR_KEY_VLAN .tpid to the
FLOW_DISSECTOR_KEY_CVLAN .tpid
- the original FLOW_DISSECTOR_KEY_CVLAN .tpid to the .n_proto field.
2) .n_proto is set to 802.1q or 802.1ad. Then, transfer:
- the .n_proto field to FLOW_DISSECTOR_KEY_VLAN .tpid.
- the original FLOW_DISSECTOR_KEY_VLAN .tpid to the .n_proto field.
Fixes: a82055af5959 ("netfilter: nft_payload: add VLAN offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The flow dissector representation expects the VLAN id in host byteorder.
Add the NFT_OFFLOAD_F_NETWORK2HOST flag to swap the bytes from nft_cmp.
Fixes: a82055af5959 ("netfilter: nft_payload: add VLAN offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
- add another struct flow_dissector_key_vlan for C-VLAN
- update layer 3 dependency to allow to match on IPv4/IPv6
Fixes: 89d8fd44abfb ("netfilter: nft_payload: add C-VLAN offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add CFO tracking, which stands for central frequency offset tracking, to
adjust oscillator to align central frequency of connected AP. Then, it can
yield better performance.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210416030901.7099-1-pkshih@realtek.com
|
|
After the fix from Jiri that disabled local IRQs instead of
just BHs (necessary to fix an issue with submitting a command
with IRQs already disabled), there was still a situation in
which we could deep in there enable BHs, if the device config
sets the apmg_wake_up_wa configuration, which is true on all
7000 series devices.
To fix that, but not require reverting commit 1ed08f6fb5ae
("iwlwifi: remove flags argument for nic_access"), split up
nic access into a version with BH manipulation to use most
of the time, and without it for this specific case where the
local IRQs are already disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210415164821.d0f2edda1651.I75f762e0bed38914d1300ea198b86dd449b4b206@changeid
|
|
Fix the following clang warning:
drivers/bcma/driver_mips.c:55:20: warning: unused function
'mips_write32' [-Wunused-function].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1618382354-866-1-git-send-email-jiapeng.chong@linux.alibaba.com
|
|
Fix the following whitescan warning:
An unsigned value can never be less than 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1617788766-91433-1-git-send-email-jiapeng.chong@linux.alibaba.com
|
|
'get_tid_h()' is the same as 'ieee80211_get_tid()'.
So this function can be removed to save a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/68efad7a597159e22771d37fc8b4a8a613866d60.1617399010.git.christophe.jaillet@wanadoo.fr
|
|
In mwl8k_probe_hw, hw->priv->txq is freed at the first time by
dma_free_coherent() in the call chain:
if(!priv->ap_fw)->mwl8k_init_txqs(hw)->mwl8k_txq_init(hw, i).
Then in err_free_queues of mwl8k_probe_hw, hw->priv->txq is freed
at the second time by mwl8k_txq_deinit(hw, i)->dma_free_coherent().
My patch set txq->txd to NULL after the first free to avoid the
double free.
Fixes: a66098daacee2 ("mwl8k: Marvell TOPDOG wireless driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210402182627.4256-1-lyl2019@mail.ustc.edu.cn
|
|
Using a kernel with the Undefined Behaviour Sanity Checker (UBSAN) enabled, the
following array overrun is logged:
================================================================================
UBSAN: array-index-out-of-bounds in /home/finger/wireless-drivers-next/drivers/net/wireless/realtek/rtw88/phy.c:1789:34
index 5 is out of range for type 'u8 [5]'
CPU: 2 PID: 84 Comm: kworker/u16:3 Tainted: G O 5.12.0-rc5-00086-gd88bba47038e-dirty #651
Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.50 09/29/2014
Workqueue: phy0 ieee80211_scan_work [mac80211]
Call Trace:
dump_stack+0x64/0x7c
ubsan_epilogue+0x5/0x40
__ubsan_handle_out_of_bounds.cold+0x43/0x48
rtw_get_tx_power_params+0x83a/drivers/net/wireless/realtek/rtw88/0xad0 [rtw_core]
? rtw_pci_read16+0x20/0x20 [rtw_pci]
? check_hw_ready+0x50/0x90 [rtw_core]
rtw_phy_get_tx_power_index+0x4d/0xd0 [rtw_core]
rtw_phy_set_tx_power_level+0xee/0x1b0 [rtw_core]
rtw_set_channel+0xab/0x110 [rtw_core]
rtw_ops_config+0x87/0xc0 [rtw_core]
ieee80211_hw_config+0x9d/0x130 [mac80211]
ieee80211_scan_state_set_channel+0x81/0x170 [mac80211]
ieee80211_scan_work+0x19f/0x2a0 [mac80211]
process_one_work+0x1dd/0x3a0
worker_thread+0x49/0x330
? rescuer_thread+0x3a0/0x3a0
kthread+0x134/0x150
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x22/0x30
================================================================================
The statement where an array is being overrun is shown in the following snippet:
if (rate <= DESC_RATE11M)
tx_power = pwr_idx_2g->cck_base[group];
else
====> tx_power = pwr_idx_2g->bw40_base[group];
The associated arrays are defined in main.h as follows:
struct rtw_2g_txpwr_idx {
u8 cck_base[6];
u8 bw40_base[5];
struct rtw_2g_1s_pwr_idx_diff ht_1s_diff;
struct rtw_2g_ns_pwr_idx_diff ht_2s_diff;
struct rtw_2g_ns_pwr_idx_diff ht_3s_diff;
struct rtw_2g_ns_pwr_idx_diff ht_4s_diff;
};
The problem arises because the value of group is 5 for channel 14. The trivial
increase in the dimension of bw40_base fails as this struct must match the layout of
efuse. The fix is to add the rate as an argument to rtw_get_channel_group() and set
the group for channel 14 to 4 if rate <= DESC_RATE11M.
This patch fixes commit fa6dfe6bff24 ("rtw88: resolve order of tx power setting routines")
Fixes: fa6dfe6bff24 ("rtw88: resolve order of tx power setting routines")
Reported-by: Богдан Пилипенко <bogdan.pylypenko107@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210401192717.28927-1-Larry.Finger@lwfinger.net
|
|
struct wilc is declared twice. One has been declared
at 352nd line. Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210331023557.2804128-3-wanjiabing@vivo.com
|
|
struct brcmf_bus is declared twice. One has been declared
at 37th line. Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210331023557.2804128-2-wanjiabing@vivo.com
|
|
Signed-off-by: Eric Lin <dslin1010@gmail.com>
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210331010418.1632816-2-dslin1010@gmail.com
|
|
The rsi_resume() does access the bus to enable interrupts on the RSI
SDIO WiFi card, however when calling sdio_claim_host() in the resume
path, it is possible the bus is already claimed and sdio_claim_host()
spins indefinitelly. Enable the SDIO card interrupts in resume_noirq
instead to prevent anything else from claiming the SDIO bus first.
Fixes: 20db07332736 ("rsi: sdio suspend and resume support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210327235932.175896-1-marex@denx.de
|
|
Since firmware can't have proper statistics, driver update the statistics
periodically to firmware to assist in tuning performance.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210326092147.30252-1-pkshih@realtek.com
|
|
struct lbs_private has been declared at 22nd line.
Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210325064154.854245-1-wanjiabing@vivo.com
|
|
s/revsion/revision/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210323043657.1466296-1-unixbhaskar@gmail.com
|
|
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
There are some files in drivers/net/wireless/rsi which follow this syntax
in their file headers, i.e. start with '/**' like comments, which causes
unexpected warnings from kernel-doc.
E.g., running scripts/kernel-doc -none on drivers/net/wireless/rsi/rsi_coex.h
causes this warning:
"warning: wrong kernel-doc identifier on line:
* Copyright (c) 2018 Redpine Signals Inc."
Similarly for other files too.
Provide a simple fix by replacing such occurrences with general comment
format, i.e., "/*", to prevent kernel-doc from parsing it.
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210315173259.8757-1-yashsri421@gmail.com
|
|
Currently, if the user changes the pause settings, the default settings
will be restored after an interface down/up cycle, and also when
resuming from suspend. This doesn't seem to provide the best user
experience. Change this to keep user settings, and just ensure that in
jumbo mode pause is disabled.
Small drawback: When switching back mtu from jumbo to non-jumbo then
pause remains disabled (but user can enable it using ethtool).
I think that's a not too common scenario and acceptable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gcc-11 with KASAN on 32-bit arm produces a warning about a function
that needs a lot of stack space:
drivers/net/wireless/cisco/airo.c: In function 'setup_card.constprop':
drivers/net/wireless/cisco/airo.c:3960:1: error: the frame size of 1512 bytes is larger than 1400 bytes [-Werror=frame-larger-than=]
Most of this is from a single large structure that could be dynamically
allocated or moved into the per-device structure. However, as the callers
all seem to have a fairly well bounded call chain, the easiest change
is to pull out the part of the function that needs the large variables
into a separate function and mark that as noinline_for_stack. This does
not reduce the total stack usage, but it gets rid of the warning and
requires minimal changes otherwise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210323131634.2669455-1-arnd@kernel.org
|
