| Age | Commit message (Collapse) | Author |
|---|
|
APDS9160 is a combination of ALS and proximity sensors.
This patch add supports for:
- Intensity clear data and illuminance data
- Proximity data
- Gain control, rate control
- Event thresholds
Signed-off-by: Mikael Gonella-Bolduc <mgonellabolduc@dimonoff.com>
Link: https://patch.msgid.link/20250122-apds9160-driver-v5-2-5393be10279a@dimonoff.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add device tree bindings for APDS9160
Note: Using alternate email for maintainer
Signed-off-by: Mikael Gonella-Bolduc <mgonellabolduc@dimonoff.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250122-apds9160-driver-v5-1-5393be10279a@dimonoff.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Silicon Labs Si7210 is an I2C Hall effect magnetic position and
temperature sensor. The driver supports the following functionalities:
* reading the temperature measurements
* reading the magnetic field measurements in a single-shot mode
* choosing the magnetic field measurement scale (20 or 200 mT)
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Antoni Pokusinski <apokusinski01@gmail.com>
Link: https://patch.msgid.link/20250120215620.39766-3-apokusinski01@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Silicon Labs Si7210 is an I2C Hall effect magnetic position
and temperature sensor.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Antoni Pokusinski <apokusinski01@gmail.com>
Link: https://patch.msgid.link/20250120215620.39766-2-apokusinski01@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The configuration registers are not volatile and are not affected
by read operations (i.e. not precious), making them suitable to be
cached in order to reduce the number of accesses to the device.
Add support for caching (RBTREE type).
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20250119-veml6030-scale-v2-2-6bfc4062a371@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for regfields as well to simplify register operations,
taking into account the different fields for the veml6030/veml7700 and
veml6035.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20250119-veml6030-scale-v2-1-6bfc4062a371@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The key objective in ad7124_disable_one() is clearing the
AD7124_CHANNEL_EN_MSK bit in the channel register. However there is no
advantage to keep the other bits in that register because when the
channel is used next time, all fields are rewritten anyhow. So instead
of using ad7124_spi_write_mask() (which is a register read plus a
register write) use a simple register write clearing the complete
register.
Also do the same in the .disable_all() callback by using the
.disable_one() callback there.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250120140708.1093655-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
IIO uses "natural" alignment so storagebits should always be a power of
2. Change storagebits to 32 since that is the natural size to store 24
bits of data.
The ad5791 driver currently doesn't use this field anywhere and doesn't
support buffered writes, so this does not change anything. We just don't
want anyone to think that it is OK to have storagebits = 24 in other
drivers.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250122-iio-dac-ad5791-fix-storagebits-v1-1-53746e0f25cd@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
For debugging, add tracing for EC_CMD_MOTION_SENSE_CMD command:
- decode the name of the subcommand
- provide internal information for the most common sub-commands:
setting range, frequency, EC probing frequency, ...
- display return status.
When enabled, the tracing output is similar to:
/sys/kernel/debug/tracing # echo 1 > events/cros_ec/enable ; echo 1 > tracing_on ; cat trace_pipe | grep MOTIONSENSE_CMD_SENSOR_ODR
SensorDeviceImp-814 [003] ..... 686.176782: cros_ec_motion_host_cmd: MOTIONSENSE_CMD_SENSOR_ODR, id: 1, data: 200000, result: 4, return: 12500
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://patch.msgid.link/20250121232007.1020666-1-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Update ad3552r_qspi_update_reg_bits function name to a more
generic name, since used mode can be SIMPLE/DUAL/QUAD SPI.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250114-wip-bl-ad3552r-axi-v0-iio-testing-carlos-v4-9-979402e33545@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
A new FPGA HDL has been developed from ADI to support ad354xr
devices.
Add support for ad3541r and ad3542r with following additions:
- use common device_info structures for hs and non hs drivers,
- DMA buffering, use DSPI mode for ad354xr and QSPI for ad355xr,
- change sample rate to respect number of lanes.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250114-wip-bl-ad3552r-axi-v0-iio-testing-carlos-v4-8-979402e33545@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Preparing for new parts to be added also in the hs driver,
set model data structures in ad3552r-common.c, to be accessible
from both -hs and non hs driver.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250114-wip-bl-ad3552r-axi-v0-iio-testing-carlos-v4-7-979402e33545@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use "instruction" mode over initial configuration and all other
non-streaming operations.
DAC boots in streaming mode as default, and the driver is not
changing this mode.
Instruction r/w is still working because instruction is processed
from the DAC after chip select is deasserted, this works until
loop mode is 0 or greater than the instruction size.
All initial operations should be more safely done in instruction
mode, a mode provided for this.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250114-wip-bl-ad3552r-axi-v0-iio-testing-carlos-v4-6-979402e33545@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Set a better info message on wrong chip id, fixing the expected value as
read from the info struct.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250114-wip-bl-ad3552r-axi-v0-iio-testing-carlos-v4-5-979402e33545@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ad354xr requires DSPI mode (2 data lanes) to work in buffering
mode, so, depending on the DAC type, target TRANSFER_REGISTER
"MULTI_IO_MODE" bitfield can be set between:
SPI (configuration, entire ad35xxr family),
DSPI (ad354xr),
QSPI (ad355xr).
Also bus IO_MODE must be set accordingly.
About removal of AXI_DAC_CUSTOM_CTRL_SYNCED_TRANSFER, according to
the HDL history the flag has never been used. So looks like the driver
was including it by mistake or in anticipation for something that was
never implemented on HDL side.
Current HDL updated documentation confirm it is actually not in use
anymore and replaced by the IO_MODE bits.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250114-wip-bl-ad3552r-axi-v0-iio-testing-carlos-v4-4-979402e33545@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Most configuration of SPI offloads is handled opaquely using the offload
pointer that is passed to the various offload functions. However, there
are some offload features that need to be controlled on a per transfer
basis.
This patch adds a flag field to struct spi_transfer to allow specifying
such features. The first feature to be added is the ability to stream
data to/from a hardware sink/source rather than using a tx or rx buffer.
Additional flags can be added in the future as needed.
A flags field is also added to the offload struct for providers to
indicate which flags are supported. This allows for generic checking of
offload capabilities during __spi_validate() so that each offload
provider doesn't have to implement their own validation.
As a first users of this streaming capability, getter functions are
added to get a DMA channel that is directly connected to the offload.
Peripheral drivers will use this to get a DMA channel and configure it
to suit their needs.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250207-dlech-mainline-spi-engine-offload-2-v8-5-e48a489be48c@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a new driver for a generic PWM trigger for SPI offloads.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250207-dlech-mainline-spi-engine-offload-2-v8-4-e48a489be48c@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a new binding for using a PWM signal as a trigger source.
The idea here is similar to e.g. "pwm-clock" to allow a trigger source
consumer to use a PWM provider as a trigger source.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250207-dlech-mainline-spi-engine-offload-2-v8-3-e48a489be48c@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Extend SPI offloading to support hardware triggers.
This allows an arbitrary hardware trigger to be used to start a SPI
transfer that was previously set up with spi_optimize_message().
A new struct spi_offload_trigger is introduced that can be used to
configure any type of trigger. It has a type discriminator and a union
to allow it to be extended in the future. Two trigger types are defined
to start with. One is a trigger that indicates that the SPI peripheral
is ready to read or write data. The other is a periodic trigger to
repeat a SPI message at a fixed rate.
There is also a spi_offload_hw_trigger_validate() function that works
similar to clk_round_rate(). It basically asks the question of if we
enabled the hardware trigger what would the actual parameters be. This
can be used to test if the requested trigger type is actually supported
by the hardware and for periodic triggers, it can be used to find the
actual rate that the hardware is capable of.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250207-dlech-mainline-spi-engine-offload-2-v8-2-e48a489be48c@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the basic infrastructure to support SPI offload providers and
consumers.
SPI offloading is a feature that allows the SPI controller to perform
transfers without any CPU intervention. This is useful, e.g. for
high-speed data acquisition.
SPI controllers with offload support need to implement the get_offload
and put_offload callbacks and can use the devm_spi_offload_alloc() to
allocate offload instances.
SPI peripheral drivers will call devm_spi_offload_get() to get a
reference to the matching offload instance. This offload instance can
then be attached to a SPI message to request offloading that message.
It is expected that SPI controllers with offload support will check for
the offload instance in the SPI message in the ctlr->optimize_message()
callback and handle it accordingly.
CONFIG_SPI_OFFLOAD is intended to be a select-only option. Both
consumer and provider drivers should `select SPI_OFFLOAD` in their
Kconfig to ensure that the SPI core is built with offload support.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250207-dlech-mainline-spi-engine-offload-2-v8-1-e48a489be48c@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Change suggested from the AXI HDL team, modify the function
axi_dac_data_stream_enable() to check for interface busy, to avoid
possible issues when starting the stream.
Fixes: e61d7178429a ("iio: dac: adi-axi-dac: extend features")
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250114-wip-bl-ad3552r-axi-v0-iio-testing-carlos-v4-3-979402e33545@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Make available scale building more clear. This hurts the performance
quite a bit by looping throgh the scales many times instead of doing
everything in one loop. It however simplifies logic by:
- decoupling the gain and scale allocations & computations
- keeping the temporary 'per_time_gains' table inside the
per_time_scales computation function.
- separating building the 'all scales' table in own function and doing
it based on the already computed per-time scales.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Tested-by: subhajit.ghosh@tweaklogic.com
Link: https://patch.msgid.link/Z1_rRXqdhxhL6wBw@mva-rohm
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
According to Documentation/timers/delay_sleep_functions.rst,
fsleep() is the preferred delay function to be used in non-atomic
context, so switch to it accordingly.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://patch.msgid.link/20241209181624.1260868-1-festevam@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add a custom implementation of regmap read/write callbacks using the SPI
bus. This allows them to be performed at a lower SCLK rate than data
reads. Previously, all SPI transfers were being performed at a lower
speed, but with this change sample data is read at the max bus speed
while the register reads/writes remain at the lower rate.
Also remove .can_multi_write from the AD4695 driver's regmap_configs, as
this isn't implemented or needed.
For some background context, see:
https://lore.kernel.org/linux-iio/20241028163907.00007e12@Huawei.com/
Suggested-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Tested-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241113-tgamblin-ad4695_improvements-v2-3-b6bb7c758fc4@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Ensure that conversion mode is successfully exited when the command is
issued by adding an extra transfer beforehand, matching the minimum CNV
high and low times from the AD4695 datasheet. The AD4695 has a quirk
where the exit command only works during a conversion, so guarantee this
happens by triggering a conversion in ad4695_exit_conversion_mode().
Then make this even more robust by ensuring that the exit command is run
at AD4695_REG_ACCESS_SCLK_HZ rather than the bus maximum.
Signed-off-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Tested-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241113-tgamblin-ad4695_improvements-v2-2-b6bb7c758fc4@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The BMI270 IMU includes a temperature sensor. Add a channel for reading
the temperature.
Signed-off-by: Gustavo Silva <gustavograzs@gmail.com>
Link: https://patch.msgid.link/20250118-bmi270-temp-v2-1-50bc85f36ab2@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This change integrates mc3510c support into the mc3230 driver.
MC3510C uses the same registers as MC3230, but a different value scale.
Tested on Huawei MediaPad T3 10 (huawei-agassi)
Signed-off-by: Vasiliy Doylov <nekodevelopper@gmail.com>
Link: https://patch.msgid.link/20250116-mainlining-mc3510c-v4-5-a41308b85ec2@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Refactor code to support multiple generations of MCUBE devices by
defining name, chip id and product code in mc3230_chip_info struct.
Signed-off-by: Vasiliy Doylov <nekodevelopper@gmail.com>
Link: https://patch.msgid.link/20250116-mainlining-mc3510c-v4-4-a41308b85ec2@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This will make the driver auto loaded via device-tree.
Signed-off-by: Vasiliy Doylov <nekodevelopper@gmail.com>
Link: https://patch.msgid.link/20250116-mainlining-mc3510c-v4-3-a41308b85ec2@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch allows to read a mount-matrix device tree property and report
to user-space or in-kernel iio clients.
Signed-off-by: Vasiliy Doylov <nekodevelopper@gmail.com>
Link: https://patch.msgid.link/20250116-mainlining-mc3510c-v4-2-a41308b85ec2@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The MC3510C is a 3 asix digital accelerometer. It handled by the same
driver as MC3230. Document it as a trivial device.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vasiliy Doylov <nekodevelopper@gmail.com>
Link: https://patch.msgid.link/20250116-mainlining-mc3510c-v4-1-a41308b85ec2@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250114192716.912476-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ad7625 driver was submitted under a dual BSD/GPL license, but this
isn't a requirement for the code, and adds extra complexity. To make it
consistent with similar drivers, drop the BSD tag and leave it as
GPL-2.0-only.
Suggested-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Trevor Gamblin <tgamblin@baylibre.com>
Link: https://patch.msgid.link/20250114-ad7625_license-v1-1-6555b7be05ab@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use two separate static const struct ad_sigma_delta_info instances
instead of making a copy for each driver instance.
Typically in the IIO subsystem, we use multiple static const instances
of the same struct when there are different variants of the same family
of devices as opposed to making a copy for each driver instance and
modifying it.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250113-iio-adc-ad7313-fix-non-const-info-struct-v4-2-b63be3ecac4a@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Move the call to fwnode_irq_get_byname() from the driver-specific
ad7173_fw_parse_device_config() to the shared ad_sd_init() function.
The main reason for this is that we want struct ad_sigma_delta_info to
be static const data that describes the actual ADC chip, not the
application-specific configuration or any runtime state.
Previously, this struct was being used to pass the IRQ number to the
shared ad_sd_init() function. Now, this is replaced by a boolean flag
that is set at compile time and the ad_sd_init() function handles
looking up the IRQ number instead. This also has the added benefit that
if any other drivers need to make use of this in the future, they just
have to set the flag and the shared code will take care of the rest
rather than duplicating the code in each driver.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250113-iio-adc-ad7313-fix-non-const-info-struct-v4-1-b63be3ecac4a@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
There's no reason to check for regulator supply property presence before
calling devm_regulator_get_optional() as that will return -ENODEV if
the supply is not present.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://patch.msgid.link/20250109182325.3973684-2-robh@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
DTS example in the bindings should be indented with 2- or 4-spaces and
aligned with opening '- |', so correct any differences like 3-spaces or
mixtures 2- and 4-spaces in one binding.
No functional changes here, but saves some comments during reviews of
new patches built on existing code.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Nuno Sa <nuno.sa@analog.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250107125848.226899-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add a section for alert support, explaining how user can use iio events
attributes to enable alert and set thresholds.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20250108-ad7380-add-alert-support-v4-5-1751802471ba@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The alert functionality is an out of range indicator and can be used as
an early indicator of an out of bounds conversion result.
ALERT_LOW_THRESHOLD and ALERT_HIGH_THRESHOLD registers are common to all
channels.
When using 1 SDO line (only mode supported by the driver right now), i.e
data outputs only on SDOA, SDOB (or SDOD for 4 channels variants) is
used as an alert pin. The alert pin is updated at the end of the
conversion (set to low if an alert occurs) and is cleared on a falling
edge of CS.
The ALERT register contains information about the exact alert status:
channel and direction. ALERT register can be accessed using debugfs if
enabled.
User can set high/low thresholds and enable alert detection using the
regular iio events attributes:
events/in_thresh_falling_value events/in_thresh_rising_value
events/thresh_either_en
In most use cases, user will hardwire the alert pin to trigger a shutdown.
In theory, we could generate userspace IIO events for alerts, but this
is not implemented yet for several reasons [1]. This can be implemented
later if a real use case actually requires it.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
[1] https://lore.kernel.org/all/4be16272-5197-4fa1-918c-c4cdfcaee02e@baylibre.com/
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250108-ad7380-add-alert-support-v4-4-1751802471ba@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since regmap cache is now enabled, we don't need to store the
oversampling ratio in the private data structure.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20250108-ad7380-add-alert-support-v4-3-1751802471ba@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Enable regmap cache, to avoid useless access on spi bus.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20250108-ad7380-add-alert-support-v4-2-1751802471ba@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Conditionnal scoped handlers are turning out to be a real pain:
readability issues, compiler and linker handling issues among others so
rollback and remove the scoped version of iio_dvice_claim_direct_mode.
To impove code readability factorize code to set oversampling ratio.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20250108-ad7380-add-alert-support-v4-1-1751802471ba@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- Fix regression that affinitized forked child in one-shot mode.
- Harden one-shot mode against hotplug online/offline
- Enable RAPL SysWatt column by default
- Add initial PTL, CWF platform support
- Harden initial PMT code in response to early use
- Enable first built-in PMT counter: CWF c1e residency
- Refuse to run on unsupported platforms without --force, to encourage
updating to a version that supports the system, and to avoid
no-so-useful measurement results
* tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (25 commits)
tools/power turbostat: version 2025.02.02
tools/power turbostat: Add CPU%c1e BIC for CWF
tools/power turbostat: Harden one-shot mode against cpu offline
tools/power turbostat: Fix forked child affinity regression
tools/power turbostat: Add tcore clock PMT type
tools/power turbostat: version 2025.01.14
tools/power turbostat: Allow adding PMT counters directly by sysfs path
tools/power turbostat: Allow mapping multiple PMT files with the same GUID
tools/power turbostat: Add PMT directory iterator helper
tools/power turbostat: Extend PMT identification with a sequence number
tools/power turbostat: Return default value for unmapped PMT domains
tools/power turbostat: Check for non-zero value when MSR probing
tools/power turbostat: Enhance turbostat self-performance visibility
tools/power turbostat: Add fixed RAPL PSYS divisor for SPR
tools/power turbostat: Fix PMT mmaped file size rounding
tools/power turbostat: Remove SysWatt from DISABLED_BY_DEFAULT
tools/power turbostat: Add an NMI column
tools/power turbostat: add Busy% to "show idle"
tools/power turbostat: Introduce --force parameter
tools/power turbostat: Improve --help output
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Fixes and improvements for sh:
- replace seq_printf() with the more efficient
seq_put_decimal_ull_width() to increase performance when stress
reading /proc/interrupts (David Wang)
- migrate sh to the generic rule for built-in DTB to help avoid race
conditions during parallel builds which can occur because Kbuild
decends into arch/*/boot/dts twice (Masahiro Yamada)
- replace select with imply in the board Kconfig for enabling
hardware with complex dependencies. This addresses warnings which
were reported by the kernel test robot (Geert Uytterhoeven)"
* tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: boards: Use imply to enable hardware with complex dependencies
sh: Migrate to the generic rule for built-in DTB
sh: irq: Use seq_put_decimal_ull_width() for decimal values
|
|
Summary of Changes since 2024.11.30:
Fix regression in 2023.11.07 that affinitized forked child
in one-shot mode.
Harden one-shot mode against hotplug online/offline
Enable RAPL SysWatt column by default.
Add initial PTL, CWF platform support.
Harden initial PMT code in response to early use.
Enable first built-in PMT counter: CWF c1e residency
Refuse to run on unsupported platforms without --force,
to encourage updating to a version that supports the system,
and to avoid no-so-useful measurement results.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Pull misc vfs cleanups from Al Viro:
"Two unrelated patches - one is a removal of long-obsolete include in
overlayfs (it used to need fs/internal.h, but the extern it wanted has
been moved back to include/linux/namei.h) and another introduces
convenience helper constructing struct qstr by a NUL-terminated
string"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
add a string-to-qstr constructor
fs/overlayfs/namei.c: get rid of include ../internal.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fix from Thomas Bogendoerfer:
"Revert commit breaking sysv ipc for o32 ABI"
* tag 'mips_6.14_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
Revert "mips: fix shmctl/semctl/msgctl syscall for o32"
|
|
git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- various updates for special file handling: symlink handling,
support for creating sockets, cleanups, new mount options (e.g. to
allow disabling using reparse points for them, and to allow
overriding the way symlinks are saved), and fixes to error paths
- fix for kerberos mounts (allow IAKerb)
- SMB1 fix for stat and for setting SACL (auditing)
- fix an incorrect error code mapping
- cleanups"
* tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
cifs: Fix parsing native symlinks directory/file type
cifs: update internal version number
cifs: Add support for creating WSL-style symlinks
smb3: add support for IAKerb
cifs: Fix struct FILE_ALL_INFO
cifs: Add support for creating NFS-style symlinks
cifs: Add support for creating native Windows sockets
cifs: Add mount option -o reparse=none
cifs: Add mount option -o symlink= for choosing symlink create type
cifs: Fix creating and resolving absolute NT-style symlinks
cifs: Simplify reparse point check in cifs_query_path_info() function
cifs: Remove symlink member from cifs_open_info_data union
cifs: Update description about ACL permissions
cifs: Rename struct reparse_posix_data to reparse_nfs_data_buffer and move to common/smb2pdu.h
cifs: Remove struct reparse_posix_data from struct cifs_open_info_data
cifs: Remove unicode parameter from parse_reparse_point() function
cifs: Fix getting and setting SACLs over SMB1
cifs: Remove intermediate object of failed create SFU call
cifs: Validate EAs for WSL reparse points
cifs: Change translation of STATUS_PRIVILEGE_NOT_HELD to -EPERM
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull debugfs fix from Greg KH:
"Here is a single debugfs fix from Al to resolve a reported regression
in the driver-core tree. It has been reported to fix the issue"
* tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Fix the missing initializations in __debugfs_file_get()
|
