| Age | Commit message (Collapse) | Author |
|---|
|
Add pinctrl support based on "pinctrl-single" driver for HiKey970
development board from HiSilicon.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Remove fixed clock and source SoC clock for UART6 for
HiSilicon Hi3670 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Add clock nodes for HiSilicon Hi3670 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Harmless mistake, but it's incorrect. The DT spec provides recommendations
for the node names:
"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model. If appropriate, the
name should be one of the following choices:
...
interrupt-controller"
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This commit adds QSPI flash support to the iwg23s board specific
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add QSPI[01] support to the RZ/G1C SoC specific device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Adding pinctrl support for EtherAVB interface.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch enables cmt0 support on the iWave iwg23s sbc.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add CMT[01] support to r8a77470 SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds USB DMAC nodes.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch enables watchdog support on the iWave iwg23s sbc.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds watchdog support to the r8a77470 SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
[simon: moved node to preserve sort order]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Update the R-Mobile A1 (r8a7740), Emma Mobile EV2 (emev2) and
SH-Mobile AG5 (sh72a0) DTSI to include product name.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[simon: squashed similar patches]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The LVDS0 encoder on Koelsh and Porter, and the LVDS1 encoder on Lager,
are enabled in DT but have no device connected to their output. This
result in spurious messages being printed to the kernel log such as
rcar-du feb00000.display: no connector for encoder /soc/lvds@feb90000, skipping
Fix it by disabling the encoders.
Fixes: 15a1ff30d8f9 ("ARM: dts: r8a7790: Convert to new LVDS DT bindings")
Fixes: e5c3f4707f39 ("ARM: dts: r8a7791: Convert to new LVDS DT bindings")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add uSD card and eMMC support to the iwg23s single board
computer powered by the RZ/G1C SoC (a.k.a. r8a77470).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Althought interface SDHI1 found on the RZ/G1C SoC (a.k.a.
r8a77470) is compatible with the R-Car Gen3 ones, its OF
compatibility is restricted to the SoC specific compatible
string to avoid confusion, as from a more generic perspective
the RZ/G1C is sharing the most similarities with the R-Car
Gen2 family of SoCs, and there is a combination of R-Car
Gen2 compatible SDHI IPs and R-Car Gen3 compatible SDHI IP
on this specific chip.
This patch adds the SoC specific part of SDHI1 support, and
since SDHI1 comes with internal DMA, its DT node looks fairly
different from SDHI0 and SDHI2.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
RZ/G1C comes with two different types of IP for the SDHI
interfaces, SDHI0 and SDHI2 share the same IP type, and
such an IP is also compatible with the one found in R-Car
Gen2. SDHI1 IP on the other hand is compatible with R-Car
Gen3 with internal DMA.
This patch completes the SDHI support of the R-Car Gen2
compatible IPs, including fixing the max-frequency
definition of SDHI2, as it turns out there is a bug in
Section 1.3.9 of the RZ/G1C Hardware User's Manual (Rev.
1.00 Oct. 2017).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add device tree nodes for the I2C[0123] controllers. Also, add
the aliases node.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This provides a pinctrl driver for the Renesas R9A06G032 SoC
Based on a patch originally written by Michel Pollet at Renesas.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This pull request adds a compatible string to the DT necessary for the
firmware and VCHI driver to coordinate on using the correct cache line
size for the platform.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds the thermal device node and the thermal-zone for
the R8A77990 SoC.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch enables I2C DMA.
NOTE: I2C7 DMA is not supported by R-Car Gen3 Hardware User's Manual
Rev.0.80E.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds CMT{0|1|2|3} device nodes for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
rsnd driver supports SSIU now, let's use it.
Then, BUSIF DMA settings on rcar_sound,ssi (= rxu, txu) are
no longer needed.
To avoid git merge timing issue / git bisect issue,
this patch doesn't remove it so far, but will be removed in
the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds I2C-DVFS device node for the R8A77990 SoC.
v2
* Drop aliases update as in upstream it is not required to configure the
BD9571 PMIC for DDR backup, nor is the use of i2c are aliases desired.
* Do not describe the device as compatible with "renesas,rcar-gen3-iic" or
"renesas,rmobile-iic" fallback compat strings. The absence of automatic
transmission registers leads us to declare the r8a77990 IIC controller as
incompatible.
v2.1
* Reduced register range to reflect documentation
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds CAN0,1 and CANFD device nodes for the r8a77990 SoC
and enables CANFD connected to CN10 on the E3 Ebisu board using the
R8A77990 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds CAN{0,1} and CANFD controller nodes for the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add sleep state for beeper pins. Without this there was a power
increase during the suspend and standby states on V3_3D domain.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add pinctrl settings so that gpio0 wake from suspend will be supported
using buttons SW4 and SW7. Also, add pinctrl configuration for 0x954,
spi0_d0, which is an unused pin brought out to a header on the board
that in it's default state also connects to the gpio used for wakeup,
gpio0_3, which affects the state of the pin and prevents a working
wakeup unless we set the mux to a different state.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Currently uart0 uses pinctrl config set by bootloader so
create default state that can be restored after a suspend
event.
Also, modify uart0 pinctrl to include RTS and CTS pins as by
default these are not in a mode for optimal power savings.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The pins used by debugss are not configued by default, place pulldowns
on the pins for maximum power savings during sleep.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[t-kristo@ti.com: converted to use AM4372_IOPAD macro]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There are several pins on this EVM that are not in use but they can
still draw power if misconfigured. Create a pinctrl entry for these pins
and configure each one for optimal power savings.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[t-kristo@ti.com: converted to use AM4372_IOPAD macro]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add pinctrl data for ddr_vtt_toggle pin so that it is configured
for proper state during DeepSleep0. The pin should enter DS0 off mode
and hold the line low so VTT regulator is kept off while suspended.
It is also important for the PULLUP to be set on this pin so that
on removal of isolation, the VTT line is pulled high as a requirement
for bringing the DDR3 out of self-refresh.
This toggling is dependent on the IO isolation controlled by the
wkup_m3. Without placing the IOs into isolation the DS0 states set for
the pin will not be latched into effect during suspend.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As long as the kernel cmdline has "earlycon" in it, this allows
seeing debug messages earlier and does not require DEBUG_LL to
be enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When compiling the kernel with Clang, the following warning appears:
arch/arm/boot/dts/omap3-gta04.dtsi:385:56: warning: '/*' within block comment [-Wcomment]
/* OMAP3_CORE1_IOPAD(0x2194, PIN_INPUT | MUX_MODE0) /* mcbsp_clks.mcbsp_clks */
^
1 warning generated.
Fixes: 3c10507a39e8 ("ARM: dts: omap3-gta04: add mcbsp (audio subsystem) pinmux")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds PCI express channel 0 device node to the R8A77990 SoC
and enables PCIEC0 PCI express controller on the Ebisu board.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
PMS405 also features PON block, so add PON and PWRKEY nodes
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
We can use BAM DAM for serial UART data transfers, so add it
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the BAM DMA instance found in BLSP1 node of the QCS404
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
RNG hardware in QCS404 features (Execution Environment) EE for
HLOS to use, add the node for prng-ee for QCS404.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the TrustZone based remoteproc nodes and their glink edges for
adsp, cdsp and wcss. Enable them for EVB common DTS.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the scm firmware node to QCS404
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the GPIOs present on PMS405 chip.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
RTC is found on PMIC PMS405 and is same as other PMIC used, so add the
rtc node with compatible as qcom,pm8941-rtc
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
PMS405 is used in QCS405-EVB so include that with SPMI nodes
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the pms405 DT file with spmi node.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the sdcc1 node and enable it for the QCS404-EVB.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
