| Age | Commit message (Collapse) | Author |
|---|
|
If an SQ is deactivated and reactivated again, some packets could be
sent after MLX5E_SQ_STATE_ENABLED is cleared, but before
netif_tx_stop_queue, meaning that NAPI might miss some completions. In
order to handle them, make sure to trigger NAPI after SQ activation in
all cases where it can be relevant. Regular SQs, XDP SQs and XSK SQs are
good. Missing cases added: after recovery, after activating HTB SQs and
after activating PTP SQs.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add support to policy/state upper protocol selector field offload,
this will enable to select traffic for IPsec operation based on l4
protocol (TCP/UDP) with specific source/destination port.
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add XDR IB PTYS coding and XDR speed 200Gbps.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Provide more details to aid debugging.
Fixes: bf0bf77f6519 ("mlx5: Support communicating arbitrary host page size to firmware")
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Majd Dibbiny <majd@nvidia.com>
Signed-off-by: Jack Morgenstein <jackm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When device is capable of handling scaled ppm values for adjusting
frequency, conversion to ppb will not be done by the driver. Instead, the
scaled ppm value will be passed directly to the device for the frequency
adjustment operation.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Some mlx5 devices are capable of disabling RoCE. In this situation,
disablement does not need to be handled at the driver level.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Update rst file to contain general information about statistics counters
for the mlx5 driver. Add specifics about individual counters in list
tables.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Tracepoints were previously implemented but not documented till this patch
series.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Provide information for Kconfig flags defined but not documented till this
patch series for the mlx5 driver.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The mlx5 device driver documentation page has grown in size and should be
split into multiple subpages. This change also contains a table of contents
for these new subpages.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mpesw definitions should be in mpesw.h and not lag.h.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
It's redundant and incorrect to check lag is also sriov mode.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
There is no need to allocate the bool variable and can just return the value.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Use the existing wrapper mlx5_lag_dev() to access the lag object from
dev for better maintainability and consistent code.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Update the function to log an error to the user if failing to offload
the rule and while there add correct prefix for the function name.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
D. Wythe says:
====================
net/smc: optimize the parallelism of SMC-R connections
This patch set attempts to optimize the parallelism of SMC-R connections,
mainly to reduce unnecessary blocking on locks, and to fix exceptions that
occur after thoses optimization.
According to Off-CPU graph, SMC worker's off-CPU as that:
smc_close_passive_work (1.09%)
smcr_buf_unuse (1.08%)
smc_llc_flow_initiate (1.02%)
smc_listen_work (48.17%)
__mutex_lock.isra.11 (47.96%)
An ideal SMC-R connection process should only block on the IO events
of the network, but it's quite clear that the SMC-R connection now is
queued on the lock most of the time.
The goal of this patchset is to achieve our ideal situation where
network IO events are blocked for the majority of the connection lifetime.
There are three big locks here:
1. smc_client_lgr_pending & smc_server_lgr_pending
2. llc_conf_mutex
3. rmbs_lock & sndbufs_lock
And an implementation issue:
1. confirm/delete rkey msg can't be sent concurrently while
protocol allows indeed.
Unfortunately,The above problems together affect the parallelism of
SMC-R connection. If any of them are not solved. our goal cannot
be achieved.
After this patch set, we can get a quite ideal off-CPU graph as
following:
smc_close_passive_work (41.58%)
smcr_buf_unuse (41.57%)
smc_llc_do_delete_rkey (41.57%)
smc_listen_work (39.10%)
smc_clc_wait_msg (13.18%)
tcp_recvmsg_locked (13.18)
smc_listen_find_device (25.87%)
smcr_lgr_reg_rmbs (25.87%)
smc_llc_do_confirm_rkey (25.87%)
We can see that most of the waiting times are waiting for network IO
events. This also has a certain performance improvement on our
short-lived conenction wrk/nginx benchmark test:
+--------------+------+------+-------+--------+------+--------+
|conns/qps |c4 | c8 | c16 | c32 | c64 | c200 |
+--------------+------+------+-------+--------+------+--------+
|SMC-R before |9.7k | 10k | 10k | 9.9k | 9.1k | 8.9k |
+--------------+------+------+-------+--------+------+--------+
|SMC-R now |13k | 19k | 18k | 16k | 15k | 12k |
+--------------+------+------+-------+--------+------+--------+
|TCP |15k | 35k | 51k | 80k | 100k | 162k |
+--------------+------+------+-------+--------+------+--------+
The reason why the benefit is not obvious after the number of connections
has increased dues to workqueue. If we try to change workqueue to UNBOUND,
we can obtain at least 4-5 times performance improvement, reach up to half
of TCP. However, this is not an elegant solution, the optimization of it
will be much more complicated. But in any case, we will submit relevant
optimization patches as soon as possible.
Please note that the premise here is that the lock related problem
must be solved first, otherwise, no matter how we optimize the workqueue,
there won't be much improvement.
Because there are a lot of related changes to the code, if you have
any questions or suggestions, please let me know.
Thanks
D. Wythe
v1 -> v2:
1. Fix panic in SMC-D scenario
2. Fix lnkc related hashfn calculation exception, caused by operator
priority
3. Only wake up one connection if the lnk is not active
4. Delete obsolete unlock logic in smc_listen_work()
5. PATCH format, do Reverse Christmas tree
6. PATCH format, change all xxx_lnk_xxx function to xxx_link_xxx
7. PATCH format, add correct fix tag for the patches for fixes.
8. PATCH format, fix some spelling error
9. PATCH format, rename slow to do_slow
v2 -> v3:
1. add SMC-D support, remove the concept of link cluster since SMC-D has
no link at all. Replace it by lgr decision maker, who provides suggestions
to SMC-D and SMC-R on whether to create new link group.
2. Fix the corruption problem described by PATCH 'fix application
data exception' on SMC-D.
v3 -> v4:
1. Fix panic caused by uninitialization map.
v4 -> v5:
1. Make SMC-D buf creation be serial to avoid Potential error
2. Add a flag to synchronize the success of the first contact
with the ready of the link group, including SMC-D and SMC-R.
3. Fixed possible reference count leak in smc_llc_flow_start().
4. reorder the patch, make bugfix PATCH be ahead.
v5 -> v6:
1. Separate the bugfix patches to make it independent.
2. Merge patch 'fix SMC_CLC_DECL_ERR_REGRMB without smc_server_lgr_pending'
with patch 'remove locks smc_client_lgr_pending and smc_server_lgr_pending'
3. Format code styles, including alignment and reverse christmas tree
style.
4. Fix a possible memory leak in smc_llc_rmt_delete_rkey()
and smc_llc_rmt_conf_rkey().
v6 -> v7:
1. Discard patch attempting to remove global locks
2. Discard patch attempting make confirm/delete rkey process concurrently
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's clear that rmbs_lock and sndbufs_lock are aims to protect the
rmbs list or the sndbufs list.
During connection establieshment, smc_buf_get_slot() will always
be invoked, and it only performs read semantics in rmbs list and
sndbufs list.
Based on the above considerations, we replace mutex with rw_semaphore.
Only smc_buf_get_slot() use down_read() to allow smc_buf_get_slot()
run concurrently, other part use down_write() to keep exclusive
semantics.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike smc_buf_create() and smcr_buf_unuse(), smcr_lgr_reg_rmbs() is
exclusive when assigned rmb_desc was not registered, although it can be
executed in parallel when assigned rmb_desc was registered already
and only performs read semtamics on it. Hence, we can not simply replace
it with read semaphore.
The idea here is that if the assigned rmb_desc was registered already,
use read semaphore to protect the critical section, once the assigned
rmb_desc was not registered, keep using keep write semaphore still
to keep its exclusivity.
Thanks to the reusable features of rmb_desc, which allows us to execute
in parallel in most cases.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smc_buf_create() & smcr_buf_unuse()
Following is part of Off-CPU graph during frequent SMC-R short-lived
processing:
process_one_work (51.19%)
smc_close_passive_work (28.36%)
smcr_buf_unuse (28.34%)
rwsem_down_write_slowpath (28.22%)
smc_listen_work (22.83%)
smc_clc_wait_msg (1.84%)
smc_buf_create (20.45%)
smcr_buf_map_usable_links
rwsem_down_write_slowpath (20.43%)
smcr_lgr_reg_rmbs (0.53%)
rwsem_down_write_slowpath (0.43%)
smc_llc_do_confirm_rkey (0.08%)
We can clearly see that during the connection establishment time,
waiting time of connections is not on IO, but on llc_conf_mutex.
What is more important, the core critical area (smcr_buf_unuse() &
smc_buf_create()) only perfroms read semantics on links, we can
easily replace it with read semaphore.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
llc_conf_mutex was used to protect links and link related configurations
in the same link group, for example, add or delete links. However,
in most cases, the protected critical area has only read semantics and
with no write semantics at all, such as obtaining a usable link or an
available rmb_desc.
This patch do simply code refactoring, replace mutex with rw_semaphore,
replace mutex_lock with down_write and replace mutex_unlock with
up_write.
Theoretically, this replacement is equivalent, but after this patch,
we can distinguish lock granularity according to different semantics
of critical areas.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vladimir Oltean says:
====================
Updates to ENETC TXQ management
The set ensures that the number of TXQs given by enetc to the network
stack (mqprio or TX hashing) + the number of TXQs given to XDP never
exceeds the number of available TXQs.
These are the first 4 patches of series "[v5,net-next,00/17] ENETC
mqprio/taprio cleanup" from here:
https://patchwork.kernel.org/project/netdevbpf/cover/20230202003621.2679603-1-vladimir.oltean@nxp.com/
There is no change in this version compared to there. I split them off
because this contains a fix for net-next and it would be good if it
could go in quickly. I also did it to reduce the patch count of that
other series, if I need to respin it again.
====================
Link: https://lore.kernel.org/r/20230203001116.3814809-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently it can happen that an mqprio qdisc is installed with num_tc 8,
and this will reserve 8 (out of 8) TXQs for the network stack. Then we
can attach an XDP program, and this will crop 2 TXQs, leaving just 6 for
mqprio. That's not what the user requested, and we should fail it.
On the other hand, if mqprio isn't requested, we still give the 8 TXQs
to the network stack (with hashing among a single traffic class), but
then, cropping 2 TXQs for XDP is fine, because the user didn't
explicitly ask for any number of TXQs, so no expectations are violated.
Simply put, the logic that mqprio should impose a minimum number of TXQs
for the network never existed. Let's say (more or less arbitrarily) that
without mqprio, the driver expects a minimum number of TXQs equal to the
number of CPUs (on NXP LS1028A, that is either 1, or 2). And with mqprio,
mqprio gives the minimum required number of TXQs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the blamed net-next commit, enetc_setup_xdp_prog() no longer goes
through enetc_open(), and therefore, the function which was supposed to
detect whether a BPF program exists (in order to crop some TX queues
from network stack usage), enetc_num_stack_tx_queues(), no longer gets
called.
We can move the netif_set_real_num_rx_queues() call to enetc_alloc_msix()
(probe time), since it is a runtime invariant. We can do the same thing
with netif_set_real_num_tx_queues(), and let enetc_reconfigure_xdp_cb()
explicitly recalculate and change the number of stack TX queues.
Fixes: c33bfaf91c4c ("net: enetc: set up XDP program under enetc_reconfigure()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
enetc_reconfigure() was modified in commit c33bfaf91c4c ("net: enetc:
set up XDP program under enetc_reconfigure()") to take an optional
callback that runs while the netdev is down, but this callback currently
cannot fail.
Code up the error handling so that the interface is restarted with the
old resources if the callback fails.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We keep a pointer to the xdp_prog in the private netdev structure as
well; what's replicated per RX ring is done so just for more convenient
access from the NAPI poll procedure.
Simplify enetc_num_stack_tx_queues() by looking at priv->xdp_prog rather
than iterating through the information replicated per RX ring.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric Dumazet says:
====================
raw: add drop reasons and use another hash function
Two first patches add drop reasons to raw input processing.
Last patch spreads RAW sockets in the shared hash tables
to avoid long hash buckets in some cases.
====================
Link: https://lore.kernel.org/r/20230202094100.3083177-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some applications seem to rely on RAW sockets.
If they use private netns, we can avoid piling all RAW
sockets bound to a given protocol into a single bucket.
Also place (struct raw_hashinfo).lock into its own
cache line to limit false sharing.
Alternative would be to have per-netns hashtables,
but this seems too expensive for most netns
where RAW sockets are not used.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use existing helpers and drop reason codes for RAW input path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use existing helpers and drop reason codes for RAW input path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Moshe Shemesh says:
====================
devlink: Move devlink dev code to a separate file
This patchset is moving code from the file leftover.c to new file dev.c.
About 1.3K lines are moved by this patchset covering most of the devlink
dev object callbacks and functionality: reload, eswitch, info, flash and
selftest.
====================
Link: https://lore.kernel.org/r/1675349226-284034-1-git-send-email-moshe@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move devlink dev selftest callbacks and related code from leftover.c to
file dev.c. No functional change in this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As all users of the struct devlink_info_req are already in dev.c, move
this struct from devl_internal.c to be local in dev.c.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move devlink dev flash callbacks, helpers and other related code from
leftover.c to dev.c. No functional change in this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move devlink dev info callbacks, related drivers helpers functions and
other related code from leftover.c to dev.c. No functional change in
this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move devlink dev eswitch callbacks and related code from leftover.c to
file dev.c. No functional change in this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move devlink dev reload callback and related code from leftover.c to
file dev.c. No functional change in this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move devlink dev get and dump callbacks and related dev code to new file
dev.c. This file shall include all callbacks that are specific on
devlink dev object.
No functional change in this patch.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that commit 028fb19c6ba7 ("netlink: provide an ability to set
default extack message") provides a weak function that doesn't override
an existing extack message provided by the driver, it makes sense to use
it also for LAG and HSR offloading, not just for bridge offloading.
Also consistently put the message string on a separate line, to reduce
line length from 92 to 84 characters.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230202140354.3158129-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Call ice_unload() and ice_load() in driver reinit flow.
Block reinit when switchdev, ADQ or SRIOV is active. In reload path we
don't want to rebuild all features. Ask user to remove them instead of
quitely removing it in reload path.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_vsi_cfg() is called from different contexts:
1) VSI exsist in HW, but it is reconfigured, because of changing queues
for example -> update instead of init should be used
2) VSI doesn't exsist, because rest has happened -> init command should
be sent
To support both cases pass boolean value which will store information
what type of command has to be sent to HW.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In deconfig VSI shouldn't be deleted from hw.
Rewrite VSI delete function to reflect that sometimes it is only needed
to remove VSI from hw without freeing the memory:
ice_vsi_delete() -> delete from HW and free memory
ice_vsi_delete_from_hw() -> delete only from HW
Value returned from ice_vsi_free() is never used. Change return type to
void.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In driver reload path the netdev isn't removed, but VSI is. Remove
filters on netdev right after removing them on VSI.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Part of code from probe can be reused in reload flow. Move this code to
separate function. Create unroll functions for each part of
initialization, like: ice_init_dev() and ice_deinit_dev(). It
simplifies unrolling and can be used in remove flow.
Avoid freeing port info as it could be reused in reload path.
Will be freed in remove path since is allocated via devm_kzalloc().
Also clean the remove path to reflect the init steps.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When allocating the ICE_VSI_CTRL, the allocated struct ice_vsi pointer is
stored into the PF's pf->vsi array at a fixed location. This was
historically done on the basis that it could provide an O(1) lookup for the
special control VSI.
Since we store the ctrl_vsi_idx, we already have O(1) lookup regardless of
where in the array we store this VSI.
Simplify the logic in ice_vsi_alloc by using the same method of storing the
control VSI as other types of VSIs.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Main goal is to reuse the same functions in VSI config and rebuild
paths.
To do this split ice_vsi_setup into smaller pieces and reuse it during
rebuild.
ice_vsi_alloc() should only alloc memory, not set the default values
for VSI.
Move setting defaults to separate function. This will allow config of
already allocated VSI, for example in reload path.
The path is mostly moving code around without introducing new
functionality. Functions ice_vsi_cfg() and ice_vsi_decfg() were
added, but they are using code that already exist.
Use flag to pass information about VSI initialization during rebuild
instead of using boolean value.
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Do few small cleanups:
1) Rename the function to reflect that it doesn't configure all things
related to VSI. ice_vsi_cfg_lan() better fits to what function is doing.
ice_vsi_cfg() can be use to name function that will configure whole VSI.
2) Remove unused ethtype field from VSI. There is no need to set
ethtype here, because it is never used.
3) Remove unnecessary check for ICE_VSI_CHNL. There is check for
ICE_VSI_CHNL in ice_vsi_get_qs, so there is no need to check it before
calling the function.
4) Simplify ice_vsi_alloc() call. There is no need to check the type of
VSI before calling ice_vsi_alloc(). For ICE_VSI_CHNL vf is always NULL
(ice_vsi_setup() is called with vf=NULL).
For ICE_VSI_VF or ICE_VSI_CTRL ch is always NULL and for other VSI types
ch and vf are always NULL.
5) Remove unnecessary call to ice_vsi_dis_irq(). ice_vsi_dis_irq() will
be called in ice_vsi_close() flow (ice_vsi_close() -> ice_vsi_down() ->
ice_vsi_dis_irq()). Remove unnecessary call.
6) Don't remove specific filters in release. All hw filters are removed
in ice_fltr_remove_alli(), which is always called in VSI release flow.
There is no need to remove only ethertype filters before calling
ice_fltr_remove_all().
7) Rename ice_vsi_clear() to ice_vsi_free(). As ice_vsi_clear() only
free memory allocated in ice_vsi_alloc() rename it to ice_vsi_free()
which better shows what function is doing.
8) Free coalesce param in rebuild. There is potential memory leak if
configuration of VSI lan fails. Free coalesce to avoid it.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use xa_array instead of deprecated ida to alloc id for RDMA aux driver.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Simplify probe flow by moving all RDMA related code to ice_init_rdma().
Unroll irq allocation if RDMA initialization fails.
Implement ice_deinit_rdma() and use it in remove flow.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Frank Sae says:
====================
net: add dts for yt8521 and yt8531s, add driver for yt8531
Add dts for yt8521 and yt8531s, add driver for yt8531.
These patches have been verified on our AM335x platform (motherboard)
which has one integrated yt8521 and one RGMII interface.
It can connect to daughter boards like yt8531s or yt8531 board.
v5:
- change the compatible of yaml
- change the maintainers of yaml from "frank sae" to "Frank Sae"
v4:
- change default tx delay from 150ps to 1950ps
- add compatible for yaml
v3:
- change default rx delay from 1900ps to 1950ps
- moved ytphy_rgmii_clk_delay_config_with_lock from yt8521's patch to yt8531's patch
- removed unnecessary checks of phydev->attached_dev->dev_addr
v2:
- split BIT macro as one patch
- split "dts for yt8521/yt8531s ... " patch as two patches
- use standard rx-internal-delay-ps and tx-internal-delay-ps, removed motorcomm,sds-tx-amplitude
- removed ytphy_parse_dt, ytphy_probe_helper and ytphy_config_init_helper
- not store dts arg to yt8521_priv
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have
verified the driver on AM335x platform with yt8531 board. On the
board, yt8531 gigabit ethernet phy works in utp mode, RGMII
interface, supports 1000M/100M/10M speeds, and wol(magic package).
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
