| Age | Commit message (Collapse) | Author |
|---|
|
In RAID_5/6 We used to not permit an IO that it's end
byte is not stripe_size aligned and spans more than one stripe.
.i.e the caller must check if after submission the actual
transferred bytes is shorter, and would need to resubmit
a new IO with the remainder.
Exofs supports this, and NFS was supposed to support this
as well with it's short write mechanism. But late testing has
exposed a CRASH when this is used with none-RPC layout-drivers.
The change at NFS is deep and risky, in it's place the fix
at ORE to lift the limitation is actually clean and simple.
So here it is below.
The principal here is that in the case of unaligned IO on
both ends, beginning and end, we will send two read requests
one like old code, before the calculation of the first stripe,
and also a new site, before the calculation of the last stripe.
If any "boundary" is aligned or the complete IO is within a single
stripe. we do a single read like before.
The code is clean and simple by splitting the old _read_4_write
into 3 even parts:
1._read_4_write_first_stripe
2. _read_4_write_last_stripe
3. _read_4_write_execute
And calling 1+3 at the same place as before. 2+3 before last
stripe, and in the case of all in a single stripe then 1+2+3
is preformed additively.
Why did I not think of it before. Well I had a strike of
genius because I have stared at this code for 2 years, and did
not find this simple solution, til today. Not that I did not try.
This solution is much better for NFS than the previous supposedly
solution because the short write was dealt with out-of-band after
IO_done, which would cause for a seeky IO pattern where as in here
we execute in order. At both solutions we do 2 separate reads, only
here we do it within a single IO request. (And actually combine two
writes into a single submission)
NFS/exofs code need not change since the ORE API communicates the new
shorter length on return, what will happen is that this case would not
occur anymore.
hurray!!
[Stable this is an NFS bug since 3.2 Kernel should apply cleanly]
CC: Stable Tree <stable@kernel.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
|
|
|
|
This implements simple support for adjusting the pin config value via the
pinctrl API. The pinconf-generic code is abandoned for now until we've
got a chance to revamp the pinmux_type state tracking that's needed by
legacy code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
If list_for_each_entry, etc complete a traversal of the list, the iterator
variable ends up pointing to an address at an offset from the list head,
and not a meaningful structure. Thus this value should not be used after
the end of the iterator. Replace a field access from orphan by NULL in two
places.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier c;
expression E;
iterator name list_for_each_entry;
statement S;
@@
list_for_each_entry(c,...) { ... when != break;
when forall
when strict
}
...
(
c = E
|
*c
)
// </smpl>
Artem: fortunately, this did not cause any issues because we iterate the orphan
list using the elements count, so we never dereferenced the corrupted pointer.
This is why I do not send this patch to -stable. But otherwise - well spotted!
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
In the log reply code we assume that 'c->lhead_offs' is known and may be
non-zero, which is not the case because we do not store it in the master
node and have to find out by scanning on every mount. Knowing this fact
allows us to simplify the log scanning loop a bit and remove a couple
of unneeded local variables.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
This patch adds another debugfs knob which switches UBIFS to R/O mode.
I needed it while trying to reproduce the 'first log node is not CS node'
bug. Without this debugfs knob you have to perform a power cut to repruduce
the bug. The knob is named 'ro_error' and all it does is it sets the
'ro_error' UBIFS flag which makes UBIFS disallow any further writes - even
write-back will fail with -EROFS. Useful for debugging.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
Fix the following compilation warning:
fs/ubifs/dir.c: In function 'ubifs_rename':
fs/ubifs/dir.c:972:15: warning: 'saved_nlink' may be used uninitialized
in this function
Use the 'uninitialized_var()' macro to get rid of this false-positive.
Artem: massaged the patch a bit.
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
While this code is still being shuffled around the KBUILD_MODNAME value
isn't particularly useful, switch to something a bit more useful.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
UBIFS has a feature called "empty space fix-up" which is a quirk to work-around
limitations of dumb flasher programs. Namely, of those flashers that are unable
to skip NAND pages full of 0xFFs while flashing, resulting in empty space at
the end of half-filled eraseblocks to be unusable for UBIFS. This feature is
relatively new (introduced in v3.0).
The fix-up routine (fixup_free_space()) is executed only once at the very first
mount if the superblock has the 'space_fixup' flag set (can be done with -F
option of mkfs.ubifs). It basically reads all the UBIFS data and metadata and
writes it back to the same LEB. The routine assumes the image is pristine and
does not have anything in the journal.
There was a bug in 'fixup_free_space()' where it fixed up the log incorrectly.
All but one LEB of the log of a pristine file-system are empty. And one
contains just a commit start node. And 'fixup_free_space()' just unmapped this
LEB, which resulted in wiping the commit start node. As a result, some users
were unable to mount the file-system next time with the following symptom:
UBIFS error (pid 1): replay_log_leb: first log node at LEB 3:0 is not CS node
UBIFS error (pid 1): replay_log_leb: log error detected while replaying the log at LEB 3:0
The root-cause of this bug was that 'fixup_free_space()' wrongly assumed
that the beginning of empty space in the log head (c->lhead_offs) was known
on mount. However, it is not the case - it was always 0. UBIFS does not store
in it the master node and finds out by scanning the log on every mount.
The fix is simple - just pass commit start node size instead of 0 to
'fixup_leb()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Cc: stable@vger.kernel.org [v3.0+]
Reported-by: Iwo Mergler <Iwo.Mergler@netcommwireless.com>
Tested-by: Iwo Mergler <Iwo.Mergler@netcommwireless.com>
Reported-by: James Nute <newten82@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull last minute Ceph fixes from Sage Weil:
"The important one fixes a bug in the socket failure handling behavior
that was turned up in some recent failure injection testing. The
other two are minor bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: endian bug in rbd_req_cb()
rbd: Fix ceph_snap_context size calculation
libceph: fix messenger retry
|
|
The stack_not_used() function in <linux/sched.h> assumes that stacks
grow downwards. This is not true on IA64 or PARISC, so this function
would walk off in the wrong direction and into the weeds.
Found on IA64 because of a compilation failure with recursive dependencies
on IA64_TASKSIZE and IA64_THREAD_INFO_SIZE.
Fixing the code is possible, but should be combined with other
infrastructure additions to set up the "canary" at the end of the stack.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> (failed allmodconfig build)
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Pull three md bugfixes from NeilBrown:
"One of the bugs was introduced in 3.5-rc1. Others have been there for
longer."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md/raid1: close some possible races on write errors during resync
md: avoid crash when stopping md array races with closing other open fds.
md: fix bug in handling of new_data_offset
|
|
Pull networking changes from David Miller:
"Ok, we should be good to go now"
1) We have to statically initialize the init_net device list head rather
than do so in an initcall, otherwise netprio_cgroup crashes if it's
built statically rather than modular (Mark D. Rustad)
2) Fix SKB null oopser in CIPSO ipv4 option processing (Paul Moore)
3) Qlogic maintainers update (Anirban Chakraborty)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Statically initialize init_net.dev_base_head
MAINTAINERS: Changes in qlcnic and qlge maintainers list
cipso: don't follow a NULL pointer when setsockopt() is called
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID update from Jiri Kosina:
"A final round of changes for HID for 3.5: just device ID additions."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-multitouch: add support for Zytronic panels
HID: add Sennheiser BTD500USB device support
HID: add battery quirk for Apple Wireless ANSI
|
|
The strcpy was being used to set the name of the board. Since the
destination char* was read-only and the name is set statically at
compile time; this was both wrong and redundant.
The type of char* is changed to const char* to prevent future errors.
Reported-by: Radek Masin <radek@masin.eu>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
[ Taking directly due to vacations - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Fixups are executed once the pci-device is found which is during boot
process so __init seems fine as long as the platform does not support
hotplug.
However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.
[ralf@linux-mips.org: Made piixirqmap[] in malta_piix_func0_fixup()
__initdata.]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit: 3777808873b0c49c5cf27e44c948dfb02675d578 [bug.h: need linux/kernel.h
for TAINT_WARN.] breaks all MIPS builds.
CC arch/mips/kernel/machine_kexec.o
In file included from include/linux/kernel.h:20:0,
from include/asm-generic/bug.h:35,
from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bug.h:41,
from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:20,
from include/linux/bitops.h:22,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/linux/log2.h: In function '__ilog2_u32':
include/linux/log2.h:34:2: error: implicit declaration of function 'fls' [-Werror=implicit-function-declaration]
include/linux/log2.h: In function '__ilog2_u64':
include/linux/log2.h:42:2: error: implicit declaration of function 'fls64' [-Werror=implicit-function-declaration]
include/linux/log2.h: In function '__roundup_pow_of_two':
include/linux/log2.h:63:2: error: implicit declaration of function 'fls_long' [-Werror=implicit-function-declaration]
In file included from include/linux/bitops.h:22:0,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
/home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h: At top level:
/home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:615:19: error: static declaration of 'fls' follows non-static declaration
include/linux/log2.h:34:9: note: previous implicit declaration of 'fls' was here
In file included from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:651:0,
from include/linux/bitops.h:22,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/asm-generic/bitops/fls64.h:18:28: error: static declaration of 'fls64' follows non-static declaration
include/linux/log2.h:42:9: note: previous implicit declaration of 'fls64' was here
In file included from include/linux/signal.h:38:0,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/linux/bitops.h:160:24: error: conflicting types for 'fls_long'
include/linux/log2.h:63:16: note: previous implicit declaration of 'fls_long' was here
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/kernel/machine_kexec.o] Error 1
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: yuasa@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Linuxppc-dev <linuxppc-dev@ozlabs.org>
Cc: Linux MIPS Mailing List <linux-mips@linux-mips.org>
Cc: Linux-sh list <linux-sh@vger.kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Patchwork: https://patchwork.linux-mips.org/patch/4000/
Tested-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Since we have delayed irq enabling to ->smp_finish()
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Just to catch a potential issue.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3852/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
To prevent a problem as commit 5fbd036b [sched: Cleanup cpu_active madness]
and commit 2baab4e9 [sched: Fix select_fallback_rq() vs cpu_active/cpu_online]
try to resolve, move set_cpu_online() to the brought up CPU and with irq
disabled.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3851/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We have move irq enable to ->smp_finish. Place ->smp_finish() a little
late to prepare for move set_cpu_online() into start_secondary.
And it's not necessary to call cpu_set(cpu, cpu_callin_map) and
synchronise_count_slave() with irq enabled.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3850/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
To prepare for smoothing set_cpu_[active|online]() mess up
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
To prepare for smoothing set_cpu_[active|online]() mess up
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3847/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
To prepare for smoothing set_cpu_[active|online]() mess up
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3846/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
To prepare for smoothing set_cpu_[active|online]() mess up
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3845/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When building oprofile as a module for R10000 or R7000 class processors,
E9000 or MIPSxx class cores since 3572a2c37f667ee49333f8863722b8f43eac506b
[MIPS: make oprofile use cp0_perfcount_irq if it is set] an
ERROR: "cp0_compare_irq" [arch/mips/oprofile/oprofile.ko] undefined!
error will happen. Fixed by exporting cp0_compare_irq.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The IPsec clock bit is 18 and not 17.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: mpm@selenic.com
Cc: herbert@gondor.apana.org.au
Patchwork: https://patchwork.linux-mips.org/patch/3323/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
cc1: warnings being treated as errors
arch/mips/kernel/perf_event_mipsxx.c:166: error: 'counters_per_cpu_to_total' defined but not used
make[2]: *** [arch/mips/kernel/perf_event_mipsxx.o] Error 1
make[2]: *** Waiting for unfinished jobs....
It was first introduced by 82091564cfd7ab8def42777a9c662dbf655c5d25 [MIPS:
perf: Add support for 64-bit perf counters.] in 3.2.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: david.daney@cavium.com
Patchwork: https://patchwork.linux-mips.org/patch/3357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
show_backtrace() was passed a NULL pointer which caused paging
request fail. Set to current task as other architectures (ARM,
etc) do when passed a NULL task pointer.
Signed-off-by: Vincent Wen <vincentwenlinux@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/3524/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Cc: Danny Kukawka <dkukawka@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3369/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel@pengutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/3565/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Fix the following build breakage in v3.4-rc1:
CC kernel/irq_work.o
In file included from include/linux/irq_work.h:4:0,
from kernel/irq_work.c:10:
include/linux/llist.h: In function 'llist_del_all':
include/linux/llist.h:178:2: error: implicit declaration of function 'BUILD_BUG_ON' [-Werror=implicit-function-declaration]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3568/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Leonid Yegoshin <yegoshin@mips.com>
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3792/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3883/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
warning: (BCM47XX_BCMA) selects BCMA_DRIVER_PCI_HOSTMODE which has unmet direct dependencies (BCMA_POSSIBLE && BCMA && MIPS && BCMA_HOST_PCI)
warning: (BCM47XX_BCMA) selects BCMA_DRIVER_PCI_HOSTMODE which has unmet direct dependencies (BCMA_POSSIBLE && BCMA && MIPS && BCMA_HOST_PCI)
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3882/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Extractd from Steven J. Hill's https://patchwork.linux-mips.org/patch/3603/.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Improper alignment can lead to unbootable systems and/or random
crashes.
[ralf@linux-mips.org: This is a lond standing bug since
6eb10bc9e2deab06630261cd05c4cb1e9a60e980 (kernel.org) rsp.
c422a10917f75fd19fa7fe070aaaa23e384dae6f (lmo) [MIPS: Clean up linker script
using new linker script macros.] so dates back to 2.6.32.]
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/3881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
There are ACPI and SMB devices in the 0x1000..0x1fff address range.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3581/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
[ralf@linux-mips.org: Cosmetic changes; also fixed up r2300_switch.S and
octeon_switch.S which needed similar modifications.]
Signed-off-by: Leonid Yegoshin <yegoshin@mips.com>
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3784/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This affects certain 4Kc cores.
Signed-off-by: Douglas Leung <douglas@mips.com>
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3855/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove usage of the '__attribute__((alias("...")))' hack that aliased
to integer arrays containing micro-assembled instructions. This hack
breaks when building a microMIPS kernel. It also makes the code much
easier to understand.
[ralf@linux-mips.org: Added back export of the clear_page and copy_page
symbols so certain modules will work again. Also fixed build with
CONFIG_SIBYTE_DMA_PAGEOPS enabled.]
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3866/
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
It's a bloody bog standard MIPS64R2 core with just a new PrId ID. Iow
that essentially means Linux just panics because it doesn't know how to
name the core.
[ralf@linux-mips.org: Split original patch into several smaller patches.]
Signed-off-by: Leonid Yegoshin <yegoshin@mips.com>
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3792/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
* pm-sleep:
PM / Sleep: call early resume handlers when suspend_noirq fails
|
|
Adding core definitions for Altera's SOCFPGA ARM platform.
Mininum support for Altera's SOCFPGA Cyclone 5 hardware.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit cf579dfb82550e34de7ccf3ef090d8b834ccd3a9 (PM / Sleep: Introduce
"late suspend" and "early resume" of devices) introduced a bug where
suspend_late handlers would be called, but if dpm_suspend_noirq returned
an error the early_resume handlers would never be called. All devices
would end up on the dpm_late_early_list, and would never be resumed
again.
Fix it by calling dpm_resume_early when dpm_suspend_noirq returns
an error.
Signed-off-by: Colin Cross <ccross@android.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
commit 4367af556133723d0f443e14ca8170d9447317cb
md/raid1: clear bad-block record when write succeeds.
Added a 'reschedule_retry' call possibility at the end of
end_sync_write, but didn't add matching code at the end of
sync_request_write. So if the writes complete very quickly, or
scheduling makes it seem that way, then we can miss rescheduling
the request and the resync could hang.
Also commit 73d5c38a9536142e062c35997b044e89166e063b
md: avoid races when stopping resync.
Fix a race condition in this same code in end_sync_write but didn't
make the change in sync_request_write.
This patch updates sync_request_write to fix both of those.
Patch is suitable for 3.1 and later kernels.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Original-version-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
md will refuse to stop an array if any other fd (or mounted fs) is
using it.
When any fs is unmounted of when the last open fd is closed all
pending IO will be flushed (e.g. sync_blockdev call in __blkdev_put)
so there will be no pending IO to worry about when the array is
stopped.
However in order to send the STOP_ARRAY ioctl to stop the array one
must first get and open fd on the block device.
If some fd is being used to write to the block device and it is closed
after mdadm open the block device, but before mdadm issues the
STOP_ARRAY ioctl, then there will be no last-close on the md device so
__blkdev_put will not call sync_blockdev.
If this happens, then IO can still be in-flight while md tears down
the array and bad things can happen (use-after-free and subsequent
havoc).
So in the case where do_md_stop is being called from an open file
descriptor, call sync_block after taking the mutex to ensure there
will be no new openers.
This is needed when setting a read-write device to read-only too.
Cc: stable@vger.kernel.org
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit c6563a8c38fde3c1c7fc925a10bde3ca20799301
md: add possibility to change data-offset for devices.
introduced a 'new_data_offset' attribute which should normally
be the same as 'data_offset', but can be explicitly set to a different
value to allow a reshape operation to move the data.
Unfortunately when the 'data_offset' is explicitly set through
sysfs, the new_data_offset is not also set, so the two would become
out-of-sync incorrectly.
One result of this is that trying to set the 'size' after the
'data_offset' would fail because it is not permitted to set the size
when the 'data_offset' and 'new_data_offset' are different - as that
can be confusing.
Consequently when mdadm tried to do this while assembling an IMSM
array it would fail.
This bug was introduced in 3.5-rc1.
Reported-by: Brian Downing <bdowning@lavos.net>
Bisected-by: Brian Downing <bdowning@lavos.net>
Tested-by: Brian Downing <bdowning@lavos.net>
Signed-off-by: NeilBrown <neilb@suse.de>
|
