| Age | Commit message (Collapse) | Author |
|---|
|
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
A few platforms are currently missing clocksource_probe() completely
in their time_init functionality. On OMAP3430 for example, this is
causing cpuidle to be pretty much dead, as the counter32k is not
going to be registered and instead a gptimer is used as a clocksource.
This will tick in periodic mode, preventing any deeper idle states.
While here, also drop one unnecessary check for populated DT before
existing clocksource_probe() call.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
After OMAP1 IRQ definitions have been changed by commit 685e2d08c54b
("ARM: OMAP1: Change interrupt numbering for sparse IRQ") introduced
in v4.2, ams-delta FIQ handler which depends on them no longer works
as expected. Fix it.
Created and tested on Amstrad Delta against Linux-4.7-rc3
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This seems to be required on some X58 chipsets on systems
with more than one IOMMU. QI does not work until it is
enabled on all IOMMUs in the system.
Reported-by: Dheeraj CVR <cvr.dheeraj@gmail.com>
Tested-by: Dheeraj CVR <cvr.dheeraj@gmail.com>
Fixes: 5f0a7f7614a9 ('iommu/vt-d: Make root entry visible for hardware right after allocation')
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fixes from Thierry Reding:
"These changes fix a bit of fallout from the introduction of the atomic
API"
* tag 'pwm/for-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: atmel-hlcdc: Fix default PWM polarity
pwm: sysfs: Get return value from pwm_apply_state()
pwm: Improve args checking in pwm_apply_state()
|
|
Pull KVM fixes from Paolo Bonzini:
- miscellaneous fixes for MIPS and s390
- one new kvm_stat for s390
- correctly disable VT-d posted interrupts with the rest of posted
interrupts
- "make randconfig" fix for x86 AMD
- off-by-one in irq route check (the "good" kind that errors out a bit
too early!)
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: vmx: check apicv is active before using VT-d posted interrupt
kvm: Fix irq route entries exceeding KVM_MAX_IRQ_ROUTES
kvm: svm: Do not support AVIC if not CONFIG_X86_LOCAL_APIC
kvm: svm: Fix implicit declaration for __default_cpu_present_to_apicid()
MIPS: KVM: Fix CACHE triggered exception emulation
MIPS: KVM: Don't unwind PC when emulating CACHE
MIPS: KVM: Include bit 31 in segment matches
MIPS: KVM: Fix modular KVM under QEMU
KVM: s390: Add stats for PEI events
KVM: s390: ignore IBC if zero
|
|
Pull nfsd bugfixes from Bruce Fields:
"Oleg Drokin found and fixed races in the nfsd4 state code that go back
to the big nfs4_lock_state removal around 3.17 (but that were also
probably hard to reproduce before client changes in 3.20 allowed the
client to perform parallel opens).
Also fix a 4.1 backchannel crash due to rpc multipath changes in 4.6.
Trond acked the client-side rpc fixes going through my tree"
* tag 'nfsd-4.7-1' of git://linux-nfs.org/~bfields/linux:
nfsd: Make init_open_stateid() a bit more whole
nfsd: Extend the mutex holding region around in nfsd4_process_open2()
nfsd: Always lock state exclusively.
rpc: share one xps between all backchannels
nfsd4/rpc: move backchannel create logic into rpc code
SUNRPC: fix xprt leak on xps allocation failure
nfsd: Fix NFSD_MDS_PR_KEY on 32-bit by adding ULL postfix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"This contains two regression fixes: one for the xattr API update and
one for using the mounter's creds in file creation in overlayfs.
There's also a fix for a bug in handling hard linked AF_UNIX sockets
that's been there from day one. This fix is overlayfs only despite
the fact that it touches code outside the overlay filesystem: d_real()
is an identity function for all except overlay dentries"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix uid/gid when creating over whiteout
ovl: xattr filter fix
af_unix: fix hard linked sockets on overlay
vfs: add d_real_inode() helper
|
|
If __key_link_begin() failed then "edit" would be uninitialized. I've
added a check to fix that.
This allows a random user to crash the kernel, though it's quite
difficult to achieve. There are three ways it can be done as the user
would have to cause an error to occur in __key_link():
(1) Cause the kernel to run out of memory. In practice, this is difficult
to achieve without ENOMEM cropping up elsewhere and aborting the
attempt.
(2) Revoke the destination keyring between the keyring ID being looked up
and it being tested for revocation. In practice, this is difficult to
time correctly because the KEYCTL_REJECT function can only be used
from the request-key upcall process. Further, users can only make use
of what's in /sbin/request-key.conf, though this does including a
rejection debugging test - which means that the destination keyring
has to be the caller's session keyring in practice.
(3) Have just enough key quota available to create a key, a new session
keyring for the upcall and a link in the session keyring, but not then
sufficient quota to create a link in the nominated destination keyring
so that it fails with EDQUOT.
The bug can be triggered using option (3) above using something like the
following:
echo 80 >/proc/sys/kernel/keys/root_maxbytes
keyctl request2 user debug:fred negate @t
The above sets the quota to something much lower (80) to make the bug
easier to trigger, but this is dependent on the system. Note also that
the name of the keyring created contains a random number that may be
between 1 and 10 characters in size, so may throw the test off by
changing the amount of quota used.
Assuming the failure occurs, something like the following will be seen:
kfree_debugcheck: out of range ptr 6b6b6b6b6b6b6b68h
------------[ cut here ]------------
kernel BUG at ../mm/slab.c:2821!
...
RIP: 0010:[<ffffffff811600f9>] kfree_debugcheck+0x20/0x25
RSP: 0018:ffff8804014a7de8 EFLAGS: 00010092
RAX: 0000000000000034 RBX: 6b6b6b6b6b6b6b68 RCX: 0000000000000000
RDX: 0000000000040001 RSI: 00000000000000f6 RDI: 0000000000000300
RBP: ffff8804014a7df0 R08: 0000000000000001 R09: 0000000000000000
R10: ffff8804014a7e68 R11: 0000000000000054 R12: 0000000000000202
R13: ffffffff81318a66 R14: 0000000000000000 R15: 0000000000000001
...
Call Trace:
kfree+0xde/0x1bc
assoc_array_cancel_edit+0x1f/0x36
__key_link_end+0x55/0x63
key_reject_and_link+0x124/0x155
keyctl_reject_key+0xb6/0xe0
keyctl_negate_key+0x10/0x12
SyS_keyctl+0x9f/0xe7
do_syscall_64+0x63/0x13a
entry_SYSCALL64_slow_path+0x25/0x25
Fixes: f70e2e06196a ('KEYS: Do preallocation for __key_link()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Current versions of gdb do not interoperate cleanly with kgdb on arm64
systems because gdb and kgdb do not use the same register description.
This patch modifies kgdb to work with recent releases of gdb (>= 7.8.1).
Compatibility with gdb (after the patch is applied) is as follows:
gdb-7.6 and earlier Ok
gdb-7.7 series Works if user provides custom target description
gdb-7.8(.0) Works if user provides custom target description
gdb-7.8.1 and later Ok
When commit 44679a4f142b ("arm64: KGDB: Add step debugging support") was
introduced it was paired with a gdb patch that made an incompatible
change to the gdbserver protocol. This patch was eventually merged into
the gdb sources:
https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commit;h=a4d9ba85ec5597a6a556afe26b712e878374b9dd
The change to the protocol was mostly made to simplify big-endian support
inside the kernel gdb stub. Unfortunately the gdb project released
gdb-7.7.x and gdb-7.8.0 before the protocol incompatibility was identified
and reversed:
https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commit;h=bdc144174bcb11e808b4e73089b850cf9620a7ee
This leaves us in a position where kgdb still uses the no-longer-used
protocol; gdb-7.8.1, which restored the original behaviour, was
released on 2014-10-29.
I don't believe it is possible to detect/correct the protocol
incompatiblity which means the kernel must take a view about which
version of the gdb remote protocol is "correct". This patch takes the
view that the original/current version of the protocol is correct
and that version found in gdb-7.7.x and gdb-7.8.0 is anomalous.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
dev_pm_opp_get_sharing_cpus() returns 0 even in the case when the OPP
core doesn't know whether or not the table is shared. It works on the
majority of platforms, where the OPP table is never created before
invoking the function and then -ENODEV is returned by it.
But in the case of one platform (Jetson TK1) at least, the situation
is a bit different. The OPP table has been created (somehow) before
dev_pm_opp_get_sharing_cpus() is called and it returns 0. Its caller
treats that as 'the CPUs don't share OPPs' and that leads to degraded
performance.
Fix this by converting 'shared_opp' in struct opp_table to an enum
and making dev_pm_opp_get_sharing_cpus() return -EINVAL in case when
the value of that field is "access unknown", so that the caller can
handle it accordingly (cpufreq-dt considers that as 'all CPUs share
the table', for example).
Fixes: 6f707daa3833 "PM / OPP: Add dev_pm_opp_get_sharing_cpus()"
Reported-and-tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw : Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the omap gpmc driver it can be noticed that GPMC_CONFIG4_OEEXTRADELAY
is overwritten by the WEEXTRADELAY value from the device tree and
GPMC_CONFIG4_WEEXTRADELAY is not updated by the value from the device
tree.
As a consequence, the memory accesses cannot be configured properly when
the extra delay are needed for OE and WE.
Fix the update of GPMC_CONFIG4_WEEXTRADELAY with the value from the
device tree file and prevents GPMC_CONFIG4_OEXTRADELAY
being overwritten by the WEXTRADELAY value from the device tree.
Cc: stable@vger.kernel.org
Signed-off-by: Ocquidant, Sebastien <sebastienocquidant@eaton.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
VT-d posted interrupt is relying on the CPU side's posted interrupt.
Need to check whether VCPU's APICv is active before enabing VT-d
posted interrupt.
Fixes: d62caabb41f33d96333f9ef15e09cd26e1c12760
Cc: stable@vger.kernel.org
Signed-off-by: Yang Zhang <yang.zhang.wz@gmail.com>
Signed-off-by: Shengge Ding <shengge.dsg@alibaba-inc.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
These days, we experienced one guest crash with 8 cores and 3 disks,
with qemu error logs as bellow:
qemu-system-x86_64: /build/qemu-2.0.0/kvm-all.c:984:
kvm_irqchip_commit_routes: Assertion `ret == 0' failed.
And then we found one patch(bdf026317d) in qemu tree, which said
could fix this bug.
Execute the following script will reproduce the BUG quickly:
irq_affinity.sh
========================================================================
vda_irq_num=25
vdb_irq_num=27
while [ 1 ]
do
for irq in {1,2,4,8,10,20,40,80}
do
echo $irq > /proc/irq/$vda_irq_num/smp_affinity
echo $irq > /proc/irq/$vdb_irq_num/smp_affinity
dd if=/dev/vda of=/dev/zero bs=4K count=100 iflag=direct
dd if=/dev/vdb of=/dev/zero bs=4K count=100 iflag=direct
done
done
========================================================================
The following qemu log is added in the qemu code and is displayed when
this bug reproduced:
kvm_irqchip_commit_routes: max gsi: 1008, nr_allocated_irq_routes: 1024,
irq_routes->nr: 1024, gsi_count: 1024.
That's to say when irq_routes->nr == 1024, there are 1024 routing entries,
but in the kernel code when routes->nr >= 1024, will just return -EINVAL;
The nr is the number of the routing entries which is in of
[1 ~ KVM_MAX_IRQ_ROUTES], not the index in [0 ~ KVM_MAX_IRQ_ROUTES - 1].
This patch fix the BUG above.
Cc: stable@vger.kernel.org
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: Zhang Zhuoyu <zhangzhuoyu@cmss.chinamobile.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Enabling a component via sysfs (echo 1 > enable_source), would
trigger building a path from the enabled sources to the sink.
If there is an error in the process (e.g, sink not enabled or
the device (CPU corresponding to ETM) is not online), we never report
failure, except for leaving a message in the dmesg.
Do proper error checking for the build path and return the error.
Before:
$ echo 0 > /sys/devices/system/cpu/cpu2/online
$ echo 1 > /sys/devices/cs_etm/cpu2/enable_source
$ echo $?
0
After:
$ echo 0 > /sys/devices/system/cpu/cpu2/online
$ echo 1 > /sys/devices/cs_etm/cpu2/enable_source
-bash: echo: write error: No such device or address
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At the end of a trace collection, we try to clear the entire buffer
and enable the ETR back if it was already enabled. But, we would have
adjusted the drvdata->buf to point to the beginning of the trace data
in the trace buffer @drvdata->vaddr. So, the following code which
clears the buffer is dangerous and can cause crashes, like below :
memset(drvdata->buf, 0, drvdata->size);
Unable to handle kernel paging request at virtual address ffffff800a145000
pgd = ffffffc974726000
*pgd=00000009f3e91003, *pud=00000009f3e91003, *pmd=0000000000000000
PREEMPT SMP
Modules linked in:
CPU: 4 PID: 1692 Comm: dd Not tainted 4.7.0-rc2+ #1721
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc9734a0080 ti: ffffffc974460000 task.ti: ffffffc974460000
PC is at __memset+0x1ac/0x200
LR is at tmc_read_unprepare_etr+0x144/0x1bc
pc : [<ffffff80083a05ac>] lr : [<ffffff800859c984>] pstate: 200001c5
...
[<ffffff80083a05ac>] __memset+0x1ac/0x200
[<ffffff800859b2e4>] tmc_release+0x90/0x94
[<ffffff8008202f58>] __fput+0xa8/0x1ec
[<ffffff80082030f4>] ____fput+0xc/0x14
[<ffffff80080c3ef8>] task_work_run+0xb0/0xe4
[<ffffff8008088bf4>] do_notify_resume+0x64/0x6c
[<ffffff8008084d5c>] work_pending+0x10/0x14
Code: 91010108 54ffff4a 8b040108 cb050042 (d50b7428)
Since we clear the buffer anyway in the following call to
tmc_etr_enable_hw(), remove the erroneous memset().
Fixes: commit de5461970b3e9e1 ("coresight: tmc: allocating memory when needed")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At the end of the trace capture, we free the allocated memory,
resetting the drvdata->buf to NULL, to indicate that trace data
was collected and the next trace session should allocate the
memory in tmc_enable_etr_sink_sysfs.
The tmc_enable_etr_sink_sysfs, we only allocate memory if drvdata->vaddr
is not NULL (which is not performed at the end of previous session).
This can cause, drvdata->vaddr getting assigned NULL and later we do
memset() which causes a crash as below :
Unable to handle kernel NULL pointer dereference at virtual
address 00000000
pgd = ffffffc9747f0000
[00000000] *pgd=00000009f402e003, *pud=00000009f402e003,
*pmd=0000000000000000
Internal error: Oops: 96000046 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1592 Comm: bash Not tainted 4.7.0-rc1+ #1712
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc078fe0080 ti: ffffffc974178000 task.ti: ffffffc974178000
PC is at __memset+0x1ac/0x200
LR is at tmc_enable_etr_sink+0xf8/0x304
pc : [<ffffff80083a002c>] lr : [<ffffff800859be44>] pstate: 400001c5
sp : ffffffc97417bc00
x29: ffffffc97417bc00 x28: ffffffc974178000
Call trace:
Exception stack(0xffffffc97417ba40 to 0xffffffc97417bb60)
ba40: 0000000000000001 ffffffc974a5d098 ffffffc97417bc00 ffffff80083a002c
ba60: ffffffc974a5d118 0000000000000000 0000000000000000 0000000000000000
ba80: 0000000000000001 0000000000000000 ffffff800859bdec 0000000000000040
baa0: ffffff8008b45b58 00000000000001c0 ffffffc97417baf0 ffffff80080eddb4
bac0: 0000000000000003 ffffffc078fe0080 ffffffc078fe0960 ffffffc078fe0940
bae0: 0000000000000000 0000000000000000 00000000007fffc0 0000000000000004
bb00: 0000000000000000 0000000000000040 000000000000003f 0000000000000000
bb20: 0000000000000000 0000000000000000 0000000000000000 0000000000000001
bb40: ffffffc078fe0960 0000000000000018 ffffffffffffffff 0008669628000000
[<ffffff80083a002c>] __memset+0x1ac/0x200
[<ffffff8008599814>] coresight_enable_path+0xa8/0x1dc
[<ffffff8008599b10>] coresight_enable+0x88/0x1b8
[<ffffff8008599d88>] enable_source_store+0x3c/0x6c
[<ffffff800845eaf4>] dev_attr_store+0x18/0x28
[<ffffff80082829e8>] sysfs_kf_write+0x54/0x64
[<ffffff8008281c30>] kernfs_fop_write+0x148/0x1d8
[<ffffff8008200128>] __vfs_write+0x28/0x110
[<ffffff8008200e88>] vfs_write+0xa0/0x198
[<ffffff80082021b0>] SyS_write+0x44/0xa0
[<ffffff8008084e70>] el0_svc_naked+0x24/0x28
Code: 91010108 54ffff4a 8b040108 cb050042 (d50b7428)
This patch fixes the issue by clearing the drvdata->vaddr while we free
the allocated buffer at the end of a session, so that we allocate the
memory again.
Cc: mathieu.poirier@linaro.org
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
_coresight_build_path assumes that all the connections of a csdev
has the child_dev initialised. This may not be true if the particular
component is not supported by the kernel config(e.g TPIU) but is
present in the DT. In which case, building a path can cause a crash like this :
Unable to handle kernel NULL pointer dereference at virtual address 00000010
pgd = ffffffc9750dd000
[00000010] *pgd=00000009f5e90003, *pud=00000009f5e90003, *pmd=0000000000000000
Internal error: Oops: 96000006 [#1] PREEMPT SMP
Modules linked in:
CPU: 4 PID: 1348 Comm: bash Not tainted 4.6.0-next-20160517 #1646
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc97517a280 ti: ffffffc9762c4000 task.ti: ffffffc9762c4000
PC is at _coresight_build_path+0x18/0xe4
LR is at _coresight_build_path+0xc0/0xe4
pc : [<ffffff80083d5130>] lr : [<ffffff80083d51d8>] pstate: 20000145
sp : ffffffc9762c7ba0
[<ffffff80083d5130>] _coresight_build_path+0x18/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d5cdc>] coresight_build_path+0x40/0x68
[<ffffff80083d5e14>] coresight_enable+0x74/0x1bc
[<ffffff80083d60a0>] enable_source_store+0x3c/0x6c
[<ffffff800830b17c>] dev_attr_store+0x18/0x28
[<ffffff80081ca9c4>] sysfs_kf_write+0x40/0x50
[<ffffff80081c9e38>] kernfs_fop_write+0x140/0x1cc
[<ffffff8008163ec8>] __vfs_write+0x28/0x110
[<ffffff8008164bf0>] vfs_write+0xa0/0x174
[<ffffff8008165d18>] SyS_write+0x44/0xa0
[<ffffff8008084e70>] el0_svc_naked+0x24/0x28
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-linus
Chanwoo writes:
Update extcon for v4.7-rc4
This patch fixes the following issue:
- In the extcon-palmas.c, fix the state of VBUS when using GPIO detection.
If probe funticon don't check the state during probe, the extcon client
driver cannot get the state of VBUS gpio until the user detach the connector
and attach the connector again.
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"The main drm fixes pull for rc4: one regression fix in the connector
refcounting, and an MST fix.
There rest is nouveau, amdkfd, i915, etnaviv, and radeon/amdgpu fixes,
mostly regression or black screen fixes"
* tag 'drm-fixes-for-v4.7-rc4' of git://people.freedesktop.org/~airlied/linux: (23 commits)
drm/etnaviv: initialize iommu domain page size
drm/nouveau/iccsense: fix memory leak
drm/nouveau/Revert "drm/nouveau/device/pci: set as non-CPU-coherent on ARM64"
drm/amd/powerplay: select samu dpm 0 as boot level on polaris.
drm/amd/powerplay: update powerplay table parsing
drm/dp/mst: Always clear proposed vcpi table for port.
drm/crtc: only store the necessary data for set_config rollback
drm/crtc: fix connector reference counting mismatch in drm_crtc_helper_set_config
drm/i915/ilk: Don't disable SSC source if it's in use
Revert "drm/amdgpu: add pipeline sync while vmid switch in same ctx"
drm/amdgpu/gfx7: fix broken condition check
drm/radeon: fix asic initialization for virtualized environments
amdgpu: fix asic initialization for virtualized environments (v2)
drm/radeon: don't use fractional dividers on RS[78]80 if SS is enabled
drm/radeon: do not hard reset GPU while freezing on r600/r700 family
drm/i915: Extract physical display dimensions from VBT
drm/i915: Check VBT for port presence in addition to the strap on VLV/CHV
drm/i915: Only ignore eDP ports that are connected
drm/i915: Silence "unexpected child device config size" for VBT on 845g
drm/i915: Fix NULL pointer deference when out of PLLs in IVB
...
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Minor kconfig dependency cleanup, trivial mic mute hotkey for ideapad,
and a needed improvement in adaptive keyboard detection for thinkpad:
platform/x86:
- Drop duplicate dependencies on X86
thinkpad_acpi:
- Add support for HKEY version 0x200
ideapad_laptop:
- Add an event for mic mute hotkey"
* tag 'platform-drivers-x86-v4.7-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: Drop duplicate dependencies on X86
thinkpad_acpi: Add support for HKEY version 0x200
ideapad_laptop: Add an event for mic mute hotkey
|
|
Pull UBI fixes from Richard Weinberger:
"This contains fixes for a regression introduced in rc1"
* tag 'upstream-4.7-rc4' of git://git.infradead.org/linux-ubifs:
ubi: Don't bypass ->getattr()
Revert "mtd: switch open_mtd_by_chdev() to use of vfs_stat()"
Revert "mtd: switch ubi_open_volume_path() to vfs_stat()"
|
|
Modules which register drivers via standard path (driver_register) in
parallel can cause a warning:
WARNING: CPU: 2 PID: 3492 at ../fs/sysfs/dir.c:31 sysfs_warn_dup+0x62/0x80
sysfs: cannot create duplicate filename '/module/saa7146/drivers'
Modules linked in: hexium_gemini(+) mxb(+) ...
...
Call Trace:
...
[<ffffffff812e63a2>] sysfs_warn_dup+0x62/0x80
[<ffffffff812e6487>] sysfs_create_dir_ns+0x77/0x90
[<ffffffff8140f2c4>] kobject_add_internal+0xb4/0x340
[<ffffffff8140f5b8>] kobject_add+0x68/0xb0
[<ffffffff8140f631>] kobject_create_and_add+0x31/0x70
[<ffffffff8157a703>] module_add_driver+0xc3/0xd0
[<ffffffff8155e5d4>] bus_add_driver+0x154/0x280
[<ffffffff815604c0>] driver_register+0x60/0xe0
[<ffffffff8145bed0>] __pci_register_driver+0x60/0x70
[<ffffffffa0273e14>] saa7146_register_extension+0x64/0x90 [saa7146]
[<ffffffffa0033011>] hexium_init_module+0x11/0x1000 [hexium_gemini]
...
As can be (mostly) seen, driver_register causes this call sequence:
-> bus_add_driver
-> module_add_driver
-> module_create_drivers_dir
The last one creates "drivers" directory in /sys/module/<...>. When
this is done in parallel, the directory is attempted to be created
twice at the same time.
This can be easily reproduced by loading mxb and hexium_gemini in
parallel:
while :; do
modprobe mxb &
modprobe hexium_gemini
wait
rmmod mxb hexium_gemini saa7146_vv saa7146
done
saa7146 calls pci_register_driver for both mxb and hexium_gemini,
which means /sys/module/saa7146/drivers is to be created for both of
them.
Fix this by a new mutex in module_create_drivers_dir which makes the
test-and-create "drivers" dir atomic.
I inverted the condition and removed 'return' to avoid multiple
unlocks or a goto.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: fe480a2675ed (Modules: only add drivers/ direcory if needed)
Cc: v2.6.21+ <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull ipmi bugfix from Corey Minyard:
"Fix a fairly significant ipmi list bug
This bug could cause lists to be corrupted"
* tag 'for-linus-4.7-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: Remove smi_msg from waiting_rcv_msgs list before handle_one_recv_msg()
|
|
Move the state selection logic inside from the caller,
always making it return correct stp to use.
Signed-off-by: J . Bruce Fields <bfields@fieldses.org>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
To avoid racing entry into nfs4_get_vfs_file().
Make init_open_stateid() return with locked stateid to be unlocked
by the caller.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
It used to be the case that state had an rwlock that was locked for write
by downgrades, but for read for upgrades (opens). Well, the problem is
if there are two competing opens for the same state, they step on
each other toes potentially leading to leaking file descriptors
from the state structure, since access mode is a bitmap only set once.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Pull virtio docs and tests from Michael Tsirkin:
"This merely has some documentation and a new test, seems safe to
merge"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
tools/virtio: add noring tool
tools/virtio/ringtest: fix run-on-all.sh to work without /dev/cpu
tools/virtio/ringtest: add usage example to README
MAINTAINERS: Add file patterns for virtio device tree bindings
|
|
Updating email addresses in MAINTAINERS and .mailmap files.
Cc: stable@vger.kernel.org
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For the third time in three years, I'm changing my e-mail at Samsung.
That's bad, as it may stop communications with me for a while. So, this
time, I'll also add the mchehab@kernel.org e-mail, as it remains stable
since ever.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
into drm-fixes
radeon and amdgpu fixes for 4.7. Highlights:
- fixes for GPU VM passthrough
- fixes for powerplay on Polaris GPUs
- pll fixes for rs780/880
* 'drm-fixes-4.7' of git://people.freedesktop.org/~agd5f/linux:
drm/amd/powerplay: select samu dpm 0 as boot level on polaris.
drm/amd/powerplay: update powerplay table parsing
Revert "drm/amdgpu: add pipeline sync while vmid switch in same ctx"
drm/amdgpu/gfx7: fix broken condition check
drm/radeon: fix asic initialization for virtualized environments
amdgpu: fix asic initialization for virtualized environments (v2)
drm/radeon: don't use fractional dividers on RS[78]80 if SS is enabled
drm/radeon: do not hard reset GPU while freezing on r600/r700 family
|
|
Add logic to disable AVIC #ifndef CONFIG_X86_LOCAL_APIC.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The commit 8221c1370056 ("svm: Manage vcpu load/unload when enable AVIC")
introduces a build error due to implicit function declaration
when #ifdef CONFIG_X86_32 and #ifndef CONFIG_X86_LOCAL_APIC
(as reported by Kbuild test robot i386-randconfig-x0-06121009).
So, this patch introduces kvm_cpu_get_apicid() wrapper
around __default_cpu_present_to_apicid() with additional
handling if CONFIG_X86_LOCAL_APIC is not defined.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: commit 8221c1370056 ("svm: Manage vcpu load/unload when enable AVIC")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
into drm-fixes
just a single fix for a regression introduced by IOMMU API changes in
v4.7.
* 'drm-etnaviv-fixes' of git://git.pengutronix.de/git/lst/linux:
drm/etnaviv: initialize iommu domain page size
|
|
The spec allows backchannels for multiple clients to share the same tcp
connection. When that happens, we need to use the same xprt for all of
them. Similarly, we need the same xps.
This fixes list corruption introduced by the multipath code.
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Acked-by: Trond Myklebust <trondmy@primarydata.com>
|
|
Also simplify the logic a bit.
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Acked-by: Trond Myklebust <trondmy@primarydata.com>
|
|
Callers of rpc_create_xprt expect it to put the xprt on success and
failure.
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Acked-by: Trond Myklebust <trondmy@primarydata.com>
|
|
Fix a regression when creating a file over a whiteout. The new
file/directory needs to use the current fsuid/fsgid, not the ones from the
mounter's credentials.
The refcounting is a bit tricky: prepare_creds() sets an original refcount,
override_creds() gets one more, which revert_cred() drops. So
1) we need to expicitly put the mounter's credentials when overriding
with the updated one
2) we need to put the original ref to the updated creds (and this can
safely be done before revert_creds(), since we'll still have the ref
from override_creds()).
Reported-by: Stephen Smalley <sds@tycho.nsa.gov>
Fixes: 3fe6e52f0626 ("ovl: override creds with the ones from the superblock mounter")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Debugfs' open_proxy_open(), the ->open() installed at all inodes created
through debugfs_create_file_unsafe(),
- grabs a reference to the original file_operations instance passed to
debugfs_create_file_unsafe() via fops_get(),
- installs it at the file's ->f_op by means of replace_fops()
- and calls fops_put() on it.
Since the semantics of replace_fops() are such that the reference's
ownership is transferred, the subsequent fops_put() will result in a double
release when the file is eventually closed.
Currently, this is not an issue since fops_put() basically does a
module_put() on the file_operations' ->owner only and there don't exist any
modules calling debugfs_create_file_unsafe() yet. This is expected to
change in the future though, c.f. commit c64688081490 ("debugfs: add
support for self-protecting attribute file fops").
Remove the call to fops_put() from open_proxy_open().
Fixes: 9fd4dcece43a ("debugfs: prevent access to possibly dead
file_operations at file open")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Debugfs' full_proxy_open(), the ->open() installed at all inodes created
through debugfs_create_file(),
- grabs a reference to the original struct file_operations instance passed
to debugfs_create_file(),
- dynamically allocates a proxy struct file_operations instance wrapping
the original
- and installs this at the file's ->f_op.
Afterwards, it calls the original ->open() and passes its return value back
to the VFS layer.
Now, if that return value indicates failure, the VFS layer won't ever call
->release() and thus, neither the reference to the original file_operations
nor the memory for the proxy file_operations will get released, i.e. both
are leaked.
Upon failure of the original fops' ->open(), undo the proxy installation.
That is:
- Set the struct file ->f_op to what it had been when full_proxy_open()
was entered.
- Drop the reference to the original file_operations.
- Free the memory holding the proxy file_operations.
Fixes: 49d200deaa68 ("debugfs: prevent access to removed files' private
data")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 49d200deaa68 ("debugfs: prevent access to removed files'
private data"), a debugfs file's file_operations methods get proxied
through lifetime aware wrappers.
However, only a certain subset of the file_operations members is supported
by debugfs and ->mmap isn't among them -- it appears to be NULL from the
VFS layer's perspective.
This behaviour breaks the /sys/kernel/debug/kcov file introduced
concurrently with commit 5c9a8750a640 ("kernel: add kcov code coverage").
Since that file never gets removed, there is no file removal race and thus,
a lifetime checking proxy isn't needed.
Avoid the proxying for /sys/kernel/debug/kcov by creating it via
debugfs_create_file_unsafe() rather than debugfs_create_file().
Fixes: 49d200deaa68 ("debugfs: prevent access to removed files' private data")
Fixes: 5c9a8750a640 ("kernel: add kcov code coverage")
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rather than wait until we observe the lock being free (which might never
happen), we can also return from spin_unlock_wait if we observe that the
lock is now held by somebody else, which implies that it was unlocked
but we just missed seeing it in that state.
Furthermore, in such a scenario there is no longer a need to write back
the value that we loaded, since we know that there has been a lock
hand-off, which is sufficient to publish any stores prior to the
unlock_wait because the ARm architecture ensures that a Store-Release
instruction is multi-copy atomic when observed by a Load-Acquire
instruction.
The litmus test is something like:
AArch64
{
0:X1=x; 0:X3=y;
1:X1=y;
2:X1=y; 2:X3=x;
}
P0 | P1 | P2 ;
MOV W0,#1 | MOV W0,#1 | LDAR W0,[X1] ;
STR W0,[X1] | STLR W0,[X1] | LDR W2,[X3] ;
DMB SY | | ;
LDR W2,[X3] | | ;
exists
(0:X2=0 /\ 2:X0=1 /\ 2:X2=0)
where P0 is doing spin_unlock_wait, P1 is doing spin_unlock and P2 is
doing spin_lock.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
rk_iommu_command() takes a struct rk_iommu and iterates over the slave
MMUs, so this is doubly wrong in that we're passing in the wrong pointer
and talking to MMUs that we shouldn't be.
Fixes: cd6438c5f844 ("iommu/rockchip: Reconstruct to support multi slaves")
Cc: stable@vger.kernel.org
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Since d16e0faab91 (iommu: Allow selecting page sizes per domain) the
iommu core demands the page size to be set per domain, otherwise any
mapping attempts will be dropped. Make sure to set a valid page size
for the etnaviv iommu.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
|
|
Commit d86b8da04dfa ("arm64: spinlock: serialise spin_unlock_wait against
concurrent lockers") fixed spin_unlock_wait for LL/SC-based atomics under
the premise that the LSE atomics (in particular, the LDADDA instruction)
are indivisible.
Unfortunately, these instructions are only indivisible when used with the
-AL (full ordering) suffix and, consequently, the same issue can
theoretically be observed with LSE atomics, where a later (in program
order) load can be speculated before the write portion of the atomic
operation.
This patch fixes the issue by performing a CAS of the lock once we've
established that it's unlocked, in much the same way as the LL/SC code.
Fixes: d86b8da04dfa ("arm64: spinlock: serialise spin_unlock_wait against concurrent lockers")
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
spin_is_locked has grown two very different use-cases:
(1) [The sane case] API functions may require a certain lock to be held
by the caller and can therefore use spin_is_locked as part of an
assert statement in order to verify that the lock is indeed held.
For example, usage of assert_spin_locked.
(2) [The insane case] There are two locks, where a CPU takes one of the
locks and then checks whether or not the other one is held before
accessing some shared state. For example, the "optimized locking" in
ipc/sem.c.
In the latter case, the sequence looks like:
spin_lock(&sem->lock);
if (!spin_is_locked(&sma->sem_perm.lock))
/* Access shared state */
and requires that the spin_is_locked check is ordered after taking the
sem->lock. Unfortunately, since our spinlocks are implemented using a
LDAXR/STXR sequence, the read of &sma->sem_perm.lock can be speculated
before the STXR and consequently return a stale value.
Whilst this hasn't been seen to cause issues in practice, PowerPC fixed
the same issue in 51d7d5205d33 ("powerpc: Add smp_mb() to
arch_spin_is_locked()") and, although we did something similar for
spin_unlock_wait in d86b8da04dfa ("arm64: spinlock: serialise
spin_unlock_wait against concurrent lockers") that doesn't actually take
care of ordering against local acquisition of a different lock.
This patch adds an smp_mb() to the start of our arch_spin_is_locked and
arch_spin_unlock_wait routines to ensure that the lock value is always
loaded after any other locks have been taken by the current CPU.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
There is a problem in the non-devicetree PMU probing where some
probe functions may get the number of supported events through
smp_call_function_any() using the arm_pmu supported_cpus mask.
But at the time the probe function is called, the supported_cpus
mask is empty so the call fails. This patch makes sure the mask
is set before calling the init function rather than after.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
If USB cable is connected prior to boot, we don't get any interrupts
so we must manually check the VBUS state and report it during probe.
If we don't do it then USB controller will never know that peripheral
cable was connected till the user unplugs and replugs the cable.
Fixes: b7aad8e2685b ("extcon: palmas: Add the support for VBUS detection by using GPIO")
Cc: stable@vger.kernel.org
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
* 'linux-4.7' of git://github.com/skeggsb/linux:
drm/nouveau/iccsense: fix memory leak
drm/nouveau/Revert "drm/nouveau/device/pci: set as non-CPU-coherent on ARM64"
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
