| Age | Commit message (Collapse) | Author |
|---|
|
The supported legacy rate mask is initialized when rs
is initialized based on the remote peer supported rates.
There's no need to re mask it repeatedly with the supported
remote peer rates.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Simplify the code a bit more by extracting the rates table
building logic into a separate function and handle setting
a fixed rate for debug in a separate flow.
Also avoid using and saving ucode rate format in different
places. Instead use rs_rate struct and convert to ucode format
only when filling the rates table in the LQ command.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Current firmware doesn't handle well uAPSD in P2P Client.
When it will be fixed, the firmware will set a TLV flag to notify
the driver that uAPSD is supported in P2P client mode.
Check this flag when sending power command for P2P client.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
It is not currently implemented for SDIO, and not required for other slave
buses as well.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Clear the FW_ERROR status before the common start_fw transport code.
Remove the transport specific clears.
After these patches the FW_ERROR flag is only set and cleared by common
transport code.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
In case a sync command timeouts or Tx is stuck while a FW error
interrupt arrives, we might call iwl_op_mode_nic_error twice before
a restart has been initiated. This will cause a reprobe. Unify calls
to this function at the transport level and only call it on the first
FW error in a given by checking the transport FW error flag.
While at it, remove the privately defined iwl_nic_error from PCIE code
and use the common callback instead.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
iwl_nvm_init() return value wasn't checked in some
path, which resulted in the following panic (if
there was some issue with the nvm):
Unable to handle kernel NULL pointer dereference at virtual address 00000004
pgd = d0460000
[00000004] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP
Modules linked in: iwlmvm(+) iwlwifi mac80211 cfg80211 compat [last unloaded: compat]
PC is at iwl_mvm_mac_setup_register+0x12c/0x460 [iwlmvm]
LR is at 0x2710
pc : [<bf50dd4c>] lr : [<00002710>] psr: 20800013
sp : d00cfe18 ip : 0000081e fp : d006b908
r10: d0711408 r9 : bf532e64 r8 : d006b5bc
r7 : d01af000 r6 : bf39cefc r5 : d006ab00 r4 : d006b5a4
r3 : 00000001 r2 : 00000000 r1 : d006a120 r0 : d006b860
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This pointer was not used anywhere.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Move rs_program_fix_rate right before it's caller where we're
already in the context of an ifdef CPTCFG_MAC80211_DEBUGFS so
we can get rid of the extra ifdefs surrounding the original
location.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Stop Tx and commands from arriving to the transport layer when a FW
error has occurred. A HW recovery should take place before. Remove
transport specific checks of the same nature (note that not all
transports were protected).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The same bits are employed in all transport layers. Put the status
field in the common transport layer. This allows us to employ them
in common transport code.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The stop_hw trans callback is not well defined. It is missing in many
cleanup flows and the division of labor between stop_device/stop_hw
is cumbersome. Remove stop_hw and use stop_device to perform both.
Implement this for all current transports.
PCIE needs some extra configuration the op-mode is leaving to configure
RF kill. Expose this explicitly as a new op_mode_leave trans callback.
Take the call to stop_device outside iwl_run_mvm_init_ucode, this
makes more sense and WARN when we want to run the INIT firmware while
it has run already.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The documentation for smps_requests is unclear, rewrite it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Configure the phy context to the minimum required
bandwidth, given by ctx->min_def.
Tuning to a narrower bandwidth should reduce the
noise level and consume less power.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Configure the fw to filter multicast according to
the addresses given by mac80211.
Note that bssid should be given even if we want
to pass all the multicast frames.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This is more related to phy contexts than to mac context.
Move this function to there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This allows to tweak the power parameters per vif.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Enable power save on P2P client interface only if it is the
only bound interface.
Avoid using uAPSD if P2P client is associated to GO that uses
opportunistic power save. This is due to current FW limitation.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When monitor interface is activated device power save needs
to be disabled.
Re-consider power management status on other active
interfaces when monitor interface is bound or unbound.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
FW still does not support power management on multiple MAC interfaces.
Currently the driver enforce this limitation by disabling PM if second
interface is added. Change this behavior to allow PM on a single interface
even if other interfaces exist but not bound to any specific PHY.
PM will be enabled if only one single interface is bound.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
FW implements protective algorithm to identify AP's improper uAPSD
behavior. FW sends misbehaving AP notification in this case.
Add this notification handling. Avoid using uAPSD in next association
to the exactly same AP. Refactor iwl_mvm_power_build_cmd() to move
uAPSD related code to a separate function.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
If the device is MIMO and VHT capable it supports Tx STBC.
Unlike HT, any chip that supports VHT also support STBC so
no need for a config parameter.
Using num_of_ants multiple times warranted caching it.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
It was set to zero which reflects support of a single STS.
Set according to the number of Rx antennas which correctly
reflects the number of STSs the STA can receive in a VHT NDP.
This improves beamforming and has been tested to improve Rx
throughput.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Not all chips support STBC so allow this to be
another config parameter per chip type. If STBC
is supported then publish it in the HT caps.
Since 7260/7265/3160 chips support it - set the stbc
support bit.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This patch adds a cipher scheme support to extend a set of
the supported ciphers. The driver reads a cipher scheme list TLV
from FW image and passes it to mac80211 on hw registration.
After the cipher schemes are registered the driver handles key
installation and Tx/Rx calls related to the new ciphers.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Send firmware a Smart FIFO Configuration host command to allow
interrupt coalescing. The smart FIFO is enabled when there is
only one bound interface (other than p2p devices which are
ignored) and it is of type station, and activated while the
station is associated.
Smart Fifo allows aggragations of DMA transactions and by that
causes processor and memory controller to stay for a longer time
on lower c-states, thus saving platform power.
Firmware relies on driver to activate and disable it.
Signed-off-by: Lilach Edelstein <lilach.edelstein@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add VHT MCS/NSS set support for nl80211_set_tx_bitrate_mask().
This should be used mainly for test purpose, to check
different MCS/NSS VHT combinations.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow to read management keys stored in a station's gtk key
array with a get_key function.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Verify that a pairwise key index value on ieee80211_get_key call
doesn't exceed the boundaries of the pairwise key array.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The return value of ieee80211_ibss_csa_beacon is not aligned with the
return value of ieee80211_assign_beacon(). For consistency and to be
able to use both functions with similar code, change
ieee80211_ibss_csa_beacon() not to send the bss changed notification
itself, but return what has changed so the caller can send the
notification instead.
Tested by: Simon Wunderlich <sw@simonwunderlich.de>
Acked by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Refactor ieee80211_ibss_process_chanswitch() to use
ieee80211_channel_switch() and avoid code duplication.
Tested by: Simon Wunderlich <sw@simonwunderlich.de>
Acked by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This regression was introduced in "mac80211: cache mesh
beacon".
mesh_sync_offset_adjust_tbtt() was assuming that the
beacon would be rebuilt in every single pre-tbtt
interrupt, but now the beacon update happens on the
workqueue, and it must be ready for immediate delivery to
the driver.
Save a pointer to the meshconf IE in the beacon_data (this
works because both the IE pointer and beacon buffer are
protected by the same rcu_{dereference,assign_pointer}())
for quick updates during pre-tbtt. This is faster and a
little prettier than iterating over the elements to find
the meshconf IE every time.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Keep the sched scan req when starting sched scan, and reschedule
it in case of HW restart during sched scan.
The upper layer don't have to know about the restart.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This function is not used anywhere else than in cfg.c, so there's no
need to export it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We call ieee80211_ibss_disconnect(), which requires sdata to be
locked, so lock the sdata during ieee80211_csa_connection_drop_work().
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Can be used to add extra IEs (such as P2P NoA) without having to
reallocate the buffer.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the AP interface is stopped, free all AP and VLAN keys at
once to only require synchronize_net() once. Since that does
synchronize_net(), also move two such calls into the function
(using the new force_synchronize parameter) to avoid doing it
twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Teach sta_info_flush() to optionally also remove stations
from all VLANs associated with an AP interface to optimise
the station removal (in particular, synchronize_net().)
To not have to add the vlans argument throughout, do some
refactoring.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no reason to have one synchronize_net() for each
removed station, refactor the code slightly to have just
a single synchronize_net() for all stations.
Note that this is currently useless as hostapd removes
stations one by one and this coalescing never happens.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no reason to do this inside the sta key removal
since the keys can only be reached through the sta (and
not by the driver at all) so once the sta can no longer
be reached, the keys are safe.
This will allow further optimisation opportunities with
multiple stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If we can assume that stations are never referenced by the
driver after sta_state returns (and this is true since the
previous iwlmvm patch and for all other drivers) then we
don't need to delay station destruction, and don't need to
play tricks with rcu_barrier() etc.
This should speed up some scenarios like hostapd shutdown.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The pointer should be cleared before synchronize_rcu() so that the
consequently dead station won't be found by any lookups in the TX
or RX paths.
Also check that the station is actually the one being removed, the
check is not needed because each 4-addr VLAN can only have a single
station and non-4-addr VLANs always have a NULL pointer there, but
the code is clearer this way (and we avoid the memory write.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
iwlmvm relies on the current mac80211 behaviour of allowing
station pointers to be valid for an RCU grace period after
returning from the sta_state() callback. To optimise these
cases, this behaviour is going away, so make the driver use
the new sta_pre_rcu_remove() method to clear the pointer in
the fw_id_to_mac_id[] array.
Since this may happen while the station is still present in
the firmware, don't set the pointer to NULL but to -ENOENT
to mark this particular case. In client mode, the station
is kept even longer (until marking the MAC as unassociated)
so the drain flow must take this new behavior into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, mac80211 allows drivers to keep RCU-protected station
references that are cleared when the station is removed from the
driver and consequently needs to synchronize twice, once before
removing the station from the driver (so it can guarantee that
the station is no longer used in TX towards the driver) and once
after the station is removed from the driver.
Add a new pre-RCU-synchronisation station removal operation to
the API to allow drivers to clear/invalidate their RCU-protected
station pointers before the RCU synchronisation.
This will allow removing the second synchronisation by changing
the driver API so that the driver may no longer assume a valid
RCU-protected pointer after sta_remove/sta_state returns.
The alternative to this would be to synchronize_rcu() in all the
drivers that currently rely on this behaviour (only iwlmvm) but
that would defeat the purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
Initialize first chain flags in ath9k_build_tx99_skb() according to
configured channel mode and channel width
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
I don't have the time to maintain the TI WiLink WLAN drivers anymore.
Remove my name and mark them as Orphan.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some cards don't update the PISR properly when all SISR bits
for Tx interrupts are being cleared and as a result we get
interrupt storm. Since we handle all tx queues all together
(so we don't really use the SISR bits to do per-queue interrupt
handling), we can manualy update PISR by doing a write-to-clear
on its Tx interrupt bits.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: linux-wireless@vger.kernel.org
CC: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
CC: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: linux-wireless@vger.kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
