summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-05-25wcn36xx: Add support for Factory Test Mode (FTM)Eyal Ilsar
Introduce infrastructure for supporting Factory Test Mode (FTM) of the wireless LAN subsystem. In order for the user space to access the firmware in test mode the relevant netlink channel needs to be exposed from the kernel driver. The above is achieved as follows: 1) Register wcn36xx driver to testmode callback from netlink 2) Add testmode callback implementation to handle incoming FTM commands 3) Add FTM command packet structure 4) Add handling for GET_BUILD_RELEASE_NUMBER (msgid=0x32A2) 5) Add generic handling for all PTT_MSG packets Signed-off-by: Eyal Ilsar <eilsar@codeaurora.org> Signed-off-by: Ramon Fried <ramon.fried@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath10k: DFS Host ConfirmationSriram R
In the 10.4-3.6 firmware branch there's a new DFS Host confirmation feature which is advertised using WMI_SERVICE_HOST_DFS_CHECK_SUPPORT flag. This new features enables the ath10k host to send information to the firmware on the specifications of detected radar type. This allows the firmware to validate if the host's radar pattern detector unit is operational and check if the radar information shared by host matches the radar pulses sent as phy error events from firmware. If the check fails the firmware won't allow use of DFS channels on AP mode when using FCC regulatory region. Hence this patch is mandatory when using a firmware from 10.4-3.6 branch. Else, DFS channels on FCC regions cannot be used. Supported Chipsets : QCA9984/QCA9888/QCA4019 Firmware Version : 10.4-3.6-00104 Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: add support to get the detected radar specificationsSriram R
This enables ath10k/ath9k drivers to collect the specifications of the radar type once it is detected by the dfs pattern detector unit. Usage of the collected info is specific to driver implementation. For example, collected radar info could be used by the host driver to send to co-processors for additional processing/validation. Note: 'radar_detector_specs' data containing the specifications of different radar types which was private within dfs_pattern_detector/ dfs_pri_detector is now shared with drivers as well for making use of this information. Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: improve debug and error messages for SMDDaniel Mack
Add a missing newline in wcn36xx_smd_send_and_wait() and also log the command request and response type that was processed. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: simplify wcn36xx_smd_open()Daniel Mack
Drop the extra warning about failed allocations, both the core and the only caller of this function will warn loud enough in such cases. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: drain pending indicator messages on shutdownDaniel Mack
When the interface is shut down, wcn36xx_smd_close() potentially races against the queue worker. Make sure to cancel the work, and then free all the remnants in hal_ind_queue manually. This is again just a theoretical issue, not something that was triggered in the wild. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: set PREASSOC and IDLE stated when BSS info changesDaniel Mack
When a BSSID is joined, set the link status to 'preassoc', and set it to 'idle' when the BSS is deleted. This is what the downstream driver is doing, and it seems to improve the reliability during connect/disconnect stress tests. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: consider CTRL_EOP bit when looking for valid descriptorsDaniel Mack
In reap_tx_dxes(), when we iterate over the linked descriptors, only consider such valid that have WCN36xx_DXE_CTRL_EOP set. This is what the prima downstream driver is doing as well. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: only handle packets when ED or DONE bit is setDaniel Mack
On RX and TX interrupts, check for the WCN36XX_CH_STAT_INT_ED_MASK or WCN36XX_CH_STAT_INT_DONE_MASK in the interrupt reason register, and only handle packets when it is set. This way, reap_tx_dxes() is only invoked when needed. This brings the dequeing logic in line with what the prima downstream driver is doing. While at it, also log the interrupt reason. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: clear all masks in RX interruptDaniel Mack
Like on the TX side, check for the interrupt reason when the RX interrupt is latched and clear the ERR, DONE and ED masks. This seems to help with connection timeouts and network stream starvatations. And FWIW, the downstream driver does the same thing. Note that in analogy to the TX side, WCN36XX_DXE_0_INT_CLR should be set to WCN36XX_INT_MASK_CHAN_RX_{L,H} rather than WCN36XX_DXE_INT_CH{1,3}_MASK. It did the right thing however, as the defines happen to have identical values. Also, instead of determining register addresses and values inside wcn36xx_rx_handle_packets(), pass them as arguments. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: don't disable RX IRQ from handlerDaniel Mack
There's no need to disable the IRQ from inside its handler. Instead just grab the spinlock of the channel that is being processed. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: set DMA mask explicitlyDaniel Mack
The device takes 32-bit addresses only, so inform the DMA API about it. This is the default on msm8016, so that doesn't change anything, but it's best practice to be explicit. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25wcn36xx: fix buffer commit logic on TX pathDaniel Mack
When wcn36xx_dxe_tx_frame() is entered while the device is still processing the queue asyncronously, we are racing against the firmware code with updates to the buffer descriptors. Presumably, the firmware scans the ring buffer that holds the descriptors and scans for a valid control descriptor, and then assumes that the next descriptor contains the payload. If, however, the control descriptor is marked valid, but the payload descriptor isn't, the packet is not sent out. Another issue with the current code is that is lacks memory barriers before descriptors are marked valid. This is important because the CPU may reorder writes to memory, even if it is allocated as coherent DMA area, and hence the device may see incompletely written data. To fix this, the code in wcn36xx_dxe_tx_frame() was restructured a bit so that the payload descriptor is made valid before the control descriptor. Memory barriers are added to ensure coherency of shared memory areas. Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath10k: remove useless test before clk_disable_unprepareYueHaibing
clk_disable_unprepare() already checks that the clock pointer is valid. No need to test it before calling it. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Zimbabwe to ETSI1_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Ukraine to ETSI9_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Singapore to FCC3_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: ETSI -> FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Russia to ETSI8_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Romania to ETSI1_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Philippines to FCC3_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Peru to APL1_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map New Zealand to FCC3_ETSICSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Malasia to FCC1_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: ETSI -> FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Macedonia to ETSI1_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Isreal to ETSI3_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Honduras to FCC3_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Czech to ETSI1_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Colombia to FCC1_FCCASven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Bulgaria to ETSI1_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Brunei Darussalam to APL6_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: FCC -> ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Bangladesh to APL1_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Australia to FCC3_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Algeria to APL13_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Map Albania to ETSI1_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for FCC3_ETSICSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for ETSI9_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for ETSI8_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for APL13_WORLDSven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for APL2_FCCASven Eckelmann
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: FCC * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for UgandaSven Eckelmann
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for TanzaniaSven Eckelmann
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for SerbiaSven Eckelmann
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for ParaguyaSven Eckelmann
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for NicaraguaSven Eckelmann
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: FCC * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for MontenegroSven Eckelmann
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for MauritiusSven Eckelmann
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for KenyaSven Eckelmann
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for BermudaSven Eckelmann
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: FCC * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath: Add regulatory mapping for BahamasSven Eckelmann
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-05-25ath10k: add support to configure channel dwell timePradeep Kumar Chitrapu
Configure channel dwell time from duration of the scan request received from mac80211 when the duration is non-zero. When the scan request does not have duration value, use the default ones, the current implementation. Corresponding flag NL80211_EXT_FEATURE_SET_SCAN_DWELL is advertized. Supported Chipsets: -QCA988X/QCA9887 PCI -QCA99X0/QCA9984/QCA9888/QCA4019 PCI -QCA6174/QCA9377 PCI/USB/SDIO -WCN3990 SNOC Tested on QCA9984 with firmware ver 10.4-3.6-0010 Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-03 19:42:39 +0000