| Age | Commit message (Collapse) | Author |
|---|
|
If firmware does not support embedded supplicant, then it in turn
will not support GT rekey offloading. If this is the case, then
driver must not advertise WOWLAN flags related to GTK rekey and
it must also skip sending the GT_REKEY_OFFLOAD_CFG command.
Signed-off-by: Shrenik Shikhare <shrenik@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Race condition is observed during rmmod of mwifiex_usb:
1. The rmmod thread will call mwifiex_usb_disconnect(), download
SHUTDOWN command and do wait_event_interruptible_timeout(),
waiting for response.
2. The main thread will handle the response and will do a
wake_up_interruptible(), unblocking rmmod thread.
3. On getting unblocked, rmmod thread will make rx_cmd.urb = NULL in
mwifiex_usb_free().
4. The main thread will try to resubmit rx_cmd.urb in
mwifiex_usb_submit_rx_urb(), which is NULL.
To fix, wait for main thread to complete before calling
mwifiex_usb_free().
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a follow-up patch for commit 21c5c83ce833
("mwifiex: support sysfs initiated device coredump").
Let us avoid exporting mwifiex_send_cmd and instead use a utility
function mwifiex_fw_dump_event to achive the work.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Trivial fix to spelling mistake in rsi_dbg message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
the wl pointer can be null In case only wlcore_sdio is probed while
no WiLink module is successfully probed, as in the case of mounting a
wl12xx module while using a device tree file configured with wl18xx
related settings.
In this case the system was crashing in wl1271_suspend() as platform
device data is not set.
Make sure wl the pointer is valid before using it.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
add pci_disable_device in error handling while init_atmel_card failed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In former patch, I enqueu all C2H commands and processed by a workqueue.
In case C2H_BT_INFO will issue a H2C command to set BT reg, and wait for
a C2H ack. But it is totally impossible that C2H workqueue waits for a
C2H command, so kernel log warn
rtlwifi: :<0> btmpinfo wait (req_num=0) timeout
Since the C2H ack command C2H_BT_MP can be safely processed in interrupt
context, add a fast command path to deal with the command.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The format of C2H data is ID(1 byte) + Length(1 byte) + value, and it is
more readable to use macros to access C2H data.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We use 'struct rtl_c2hcmd' to store C2H commands originally, and the code
is slightly complex to enqueue and dequeue and also wastes time to
allocate and memcpy data. Since C2H commands are asynchronous events,
they can be processed in work queue, so RX ISR enqueues C2H result in
removal of rtl_c2h_packet_handler().
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Similar to rx_command_packet, we can call rtl_c2h_content_parsing so the
hal_op isn't necessary.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Because the hal_op rx_command_packet does C2H handler if rx packet type
is C2H, and the handler have been moved to base.c so we can call the
handler directly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Merge duplicate C2H handler and implement the handler in base.c.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We're going to merge C2H handler into one, but one special case is to
handle RA_REPORT that implements in individual IC folder. So this commit
adds a hal_op for caller in common code.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The caller of hal_op rx_command_packet will assert function pointer
before calling, so we can remove dummy functions safely.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The IDs are defined by driver and map to the fw C2H IDs, but they aren't
used now result in removal.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Move C2H definition to wifi.h, because the definitions of 8192ee, 8723be
and 8821ae are the same.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Current chips use packet-based C2H commands whose IDs differ from old
ones, so this commit simply gives C2H_V0_ as prefix of command IDs.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Move duplicate definitions from def.h of ic folder to wifi.h
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
To use keep-alive mechanism in mac80211 stack, since driver supports
reporting accurate nullfunc frame tx ack now.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In order to realize the keep-alive mechanism in mac80211 stack, reporting
accurate tx ack status for nullfunc frame is added in this commit.
If current frame is nullfunc frame, we ask firmware to report by filling
TX report bit in TX descriptor. After this frame DMA done, TX interrupt is
triggered but TX status is unknown at this moment, so enqueue this skb
into tx_report->queue. Finally, C2H report will be received if the frame
is transmitted successfully or retried over, and then we report to mac80211
with IEEE80211_TX_STAT_ACK flag only if it's successful. Otherwise, if
failure or timeout (one second), we report to mac80211 without this flag.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We can have pm_runtime_get_sync() return 1, and we can have
pm_runtime_put_sync() return -EBUSY. See rpm_suspend() and
rpm_resume() for more information.
Fix the issue by returning 0 from wl12xx_sdio_power_on() on success.
And use pm_runtime_put() instead of pm_runtime_put_sync() for
wl12xx_sdio_power_off(), then the MMC subsystem will idle the bus
when suitable.
Otherwise wlcore can sometimes get confused and may report bogus
errors and WLAN connection can fail.
Note that while wlcore checks the return value for wl1271_power_on(),
the return value is ignored for wl1271_power_off(). Let's fix them
both though to avoid further confusion in the future.
Fixes: 60f36637bbbd ("wlcore: sdio: allow pm to handle sdio power")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Salil Mehta says:
====================
Misc. bug fixes & some minor additions to HNS3 driver
This patch-set provides some bug fixes figured out during testing
and review. It also provides some additions due to running of the
existing code on the new revision of the HNS3 hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When register a RoCE client with hnae3vf device, it needs to judge
the device whether support RoCE vf function. Otherwise, it will
lead to calltrace when RoCE is not support vf function and remove
roce device.
The calltrace as follows:
[ 93.156614] Unable to handle kernel NULL pointer dereference at virtual address 00000015
<SNIP>
[ 93.278784] Call trace:
[ 93.278788] hnae3_match_n_instantiate+0x24/0xd8 [hnae3]
[ 93.278790] hnae3_register_client+0xcc/0x150 [hnae3]
[ 93.278801] hns_roce_hw_v2_init+0x18/0x1000 [hns_roce_hw_v2]
[ 93.278805] do_one_initcall+0x58/0x160
[ 93.278807] do_init_module+0x64/0x1d8
[ 93.278809] load_module+0x135c/0x15c8
[ 93.278811] SyS_finit_module+0x100/0x118
[ 93.278816] __sys_trace_return+0x0/0x4
[ 93.278827] Code: aa0003f5 12001c56 aa1e03e0 d503201f (b9402660)
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Reported-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reported-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware now supports control of all leds. Existing HNS3 driver code
only supported led locate command over SFP Fibre ports. But now it
is also supported over copper port.
This patch removes existing not needed code for the led locate
command and updates the led control command between driver and
firmware.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the previous implementation of led control for fibre port , parses the
port speed configuration, checks the link status and traffic status per
second, and updates the blink status of link led, traffic led and speed
led.
Now, the firmware takes responsibility to handle the led, the dirver just
needs to deal with locate command.
So the codes for link led, traffic led and speed led are useless now. This
patch removes these redundant codes.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we down the port, some packets are left in TX/RX buffer. When we
up the port again, these old packets are forwarded to protocol stack
or are sent to internet. It will make some problem. TX/RX buffer should
be cleared when stopping port. This patch adds some function to ensure
the buffer is clean when port is started. We should clear the rings
when clients are being un-initialized as well.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our code will ensure that hns3_clear_tx_ring is not used to cleared
RX rings and hns3_clear_rx_ring is not used to cleared TX rings. So
the ring type check is unnecessary.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RX Buffer Descriptor contains a VALID bit which indicates if the BD
is valid and has some data. This field is set by HNS3 hardware to
intimate the driver of some valid data present in the BD. nd should
be reset by the driver when BD is being used again. In the existing
code this bit was not being (re-)initialized properly and hence was
causing problems.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HNAE3 module supports kernel nic driver, user nic driver and roce driver,
and there are 3 client types. Driver uses one bit(HNAE3_CLIENT_INITED_B)
to indicate the client initialization state, it will cause confusion
for 3 client types. This patch fixes it by use 3 bits to indicate the
initialization state.
Fixes: 38caee9d3ee8 ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the firmware updates the crq's tail pointer, if the PF driver
reads the data in the crq, the data may be incomplete at this time,
which will lead to the driver read an unknown message.
This patch fixes it by checking if crq is not empty before reading the
message.
Fixes: c1a81619d73a ("net: hns3: Add mailbox interrupt handling to PF driver")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HCLGE_PROMISC_TX_EN_B and HCLGE_PROMISC_RX_EN_B are not supported
on pdev revision(0x20), new revision(0x21) supports them.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware Revision(0x21) Buffer Descriptor adds a field STRP_TAGP
for vlan stripped processed indication. STRP_TAGP field has 2 bits,
bit 0 is stripped indication of the vlan tag in outer vlan tag
field, bit 1 is stripped indication of the vlan tag in inner vlan
tag field. For each bit, 0 indicates the tag is not stripped and
1 indicates the tag is stripped.
This patch adds STRP_TAGP support for revision(0x21), and does not
change the revision(0x20) action.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HNS3 Hardware can support up to two VLAN tags in transmit leg, the PPP
module can handle the packets based on the tag1 and tag2 config. This
patch adds support for tag2 config for vlan handling
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the latest revision of the hardware, if a packet is spanning
across multiple BDs then only VLD bit and current data size info
is valid in each BD, and rest of the information is only valid
in the last BD of the packet. In such case we should make sure
we are fetching RX packet size from the first descriptor and
information like VLAN should be fetched from last BD.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct Qdisc has a lot of holes, especially after commit
a53851e2c321 ("net: sched: explicit locking in gso_cpu fallback"),
which as a side effect, moved the fields just after 'busylock'
on a new cacheline.
Since both 'padded' and 'refcnt' are not updated frequently, and
there is a hole before 'gso_skb', we can move such fields there,
saving a cacheline without any performance side effect.
Before this commit:
pahole -C Qdisc net/sche/sch_generic.o
# ...
/* size: 384, cachelines: 6, members: 25 */
/* sum members: 236, holes: 3, sum holes: 92 */
/* padding: 56 */
After this commit:
pahole -C Qdisc net/sche/sch_generic.o
# ...
/* size: 320, cachelines: 5, members: 25 */
/* sum members: 236, holes: 2, sum holes: 28 */
/* padding: 56 */
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SIMCOM are reusing a single device ID for many (all of their?)
different modems, based on different chipsets and firmwares. Newer
Qualcomm chipset generations require setting DTR to wake the QMI
function. The SIM7600E modem is using such a chipset, making it
fail to work with this driver despite the device ID match.
Fix by unconditionally enabling the SET_DTR quirk for all SIMCOM
modems using this specific device ID. This is similar to what
we already have done for another case of device IDs recycled over
multiple chipset generations: 14cf4a771b30 ("drivers: net: usb:
qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201")
Initial testing on an older SIM7100 modem shows no immediate side
effects.
Reported-by: Sebastian Sjoholm <sebastian.sjoholm@gmail.com>
Cc: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netsec network controller IP can drive 64 address bits for DMA, and
the DMA mask is set accordingly in the driver. However, the SynQuacer
SoC, which is the only silicon incorporating this IP at the moment,
integrates this IP in a manner that leaves address bits [63:40]
unconnected.
Up until now, this has not resulted in any problems, given that the DDR
controller doesn't decode those bits to begin with. However, recent
firmware updates for platforms incorporating this SoC allow the IOMMU
to be enabled, which does decode address bits [47:40], and allocates
top down from the IOVA space, producing DMA addresses that have bits
set that have been left unconnected.
Both the DT and ACPI (IORT) descriptions of the platform take this into
account, and only describe a DMA address space of 40 bits (using either
dma-ranges DT properties, or DMA address limits in IORT named component
nodes). However, even though our IOMMU and bus layers may take such
limitations into account by setting a narrower DMA mask when creating
the platform device, the netsec probe() entrypoint follows the common
practice of setting the DMA mask uncondionally, according to the
capabilities of the IP block itself rather than to its integration into
the chip.
It is currently unclear what the correct fix is here. We could hack around
it by only setting the DMA mask if it deviates from its default value of
DMA_BIT_MASK(32). However, this makes it impossible for the bus layer to
use DMA_BIT_MASK(32) as the bus limit, and so it appears that a more
comprehensive approach is required to take DMA limits imposed by the
SoC as a whole into account.
In the mean time, let's limit the DMA mask to 40 bits. Given that there
is currently only one SoC that incorporates this IP, this is a reasonable
approach that can be backported to -stable and buys us some time to come
up with a proper fix going forward.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver")
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Masahisa Kojima <masahisa.kojima@linaro.org>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
seg6_do_srh_encap and seg6_do_srh_inline can possibly do an
out-of-bounds access when adding the SRH to the packet. This no longer
happen when expanding the skb not only by the size of the SRH (+
outer IPv6 header), but also by skb->mac_len.
[ 53.793056] BUG: KASAN: use-after-free in seg6_do_srh_encap+0x284/0x620
[ 53.794564] Write of size 14 at addr ffff88011975ecfa by task ping/674
[ 53.796665] CPU: 0 PID: 674 Comm: ping Not tainted 4.17.0-rc3-ARCH+ #90
[ 53.796670] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.11.0-20171110_100015-anatol 04/01/2014
[ 53.796673] Call Trace:
[ 53.796679] <IRQ>
[ 53.796689] dump_stack+0x71/0xab
[ 53.796700] print_address_description+0x6a/0x270
[ 53.796707] kasan_report+0x258/0x380
[ 53.796715] ? seg6_do_srh_encap+0x284/0x620
[ 53.796722] memmove+0x34/0x50
[ 53.796730] seg6_do_srh_encap+0x284/0x620
[ 53.796741] ? seg6_do_srh+0x29b/0x360
[ 53.796747] seg6_do_srh+0x29b/0x360
[ 53.796756] seg6_input+0x2e/0x2e0
[ 53.796765] lwtunnel_input+0x93/0xd0
[ 53.796774] ipv6_rcv+0x690/0x920
[ 53.796783] ? ip6_input+0x170/0x170
[ 53.796791] ? eth_gro_receive+0x2d0/0x2d0
[ 53.796800] ? ip6_input+0x170/0x170
[ 53.796809] __netif_receive_skb_core+0xcc0/0x13f0
[ 53.796820] ? netdev_info+0x110/0x110
[ 53.796827] ? napi_complete_done+0xb6/0x170
[ 53.796834] ? e1000_clean+0x6da/0xf70
[ 53.796845] ? process_backlog+0x129/0x2a0
[ 53.796853] process_backlog+0x129/0x2a0
[ 53.796862] net_rx_action+0x211/0x5c0
[ 53.796870] ? napi_complete_done+0x170/0x170
[ 53.796887] ? run_rebalance_domains+0x11f/0x150
[ 53.796891] __do_softirq+0x10e/0x39e
[ 53.796894] do_softirq_own_stack+0x2a/0x40
[ 53.796895] </IRQ>
[ 53.796898] do_softirq.part.16+0x54/0x60
[ 53.796900] __local_bh_enable_ip+0x5b/0x60
[ 53.796903] ip6_finish_output2+0x416/0x9f0
[ 53.796906] ? ip6_dst_lookup_flow+0x110/0x110
[ 53.796909] ? ip6_sk_dst_lookup_flow+0x390/0x390
[ 53.796911] ? __rcu_read_unlock+0x66/0x80
[ 53.796913] ? ip6_mtu+0x44/0xf0
[ 53.796916] ? ip6_output+0xfc/0x220
[ 53.796918] ip6_output+0xfc/0x220
[ 53.796921] ? ip6_finish_output+0x2b0/0x2b0
[ 53.796923] ? memcpy+0x34/0x50
[ 53.796926] ip6_send_skb+0x43/0xc0
[ 53.796929] rawv6_sendmsg+0x1216/0x1530
[ 53.796932] ? __orc_find+0x6b/0xc0
[ 53.796934] ? rawv6_rcv_skb+0x160/0x160
[ 53.796937] ? __rcu_read_unlock+0x66/0x80
[ 53.796939] ? __rcu_read_unlock+0x66/0x80
[ 53.796942] ? is_bpf_text_address+0x1e/0x30
[ 53.796944] ? kernel_text_address+0xec/0x100
[ 53.796946] ? __kernel_text_address+0xe/0x30
[ 53.796948] ? unwind_get_return_address+0x2f/0x50
[ 53.796950] ? __save_stack_trace+0x92/0x100
[ 53.796954] ? save_stack+0x89/0xb0
[ 53.796956] ? kasan_kmalloc+0xa0/0xd0
[ 53.796958] ? kmem_cache_alloc+0xd2/0x1f0
[ 53.796961] ? prepare_creds+0x23/0x160
[ 53.796963] ? __x64_sys_capset+0x252/0x3e0
[ 53.796966] ? do_syscall_64+0x69/0x160
[ 53.796968] ? entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.796971] ? __alloc_pages_nodemask+0x170/0x380
[ 53.796973] ? __alloc_pages_slowpath+0x12c0/0x12c0
[ 53.796977] ? tty_vhangup+0x20/0x20
[ 53.796979] ? policy_nodemask+0x1a/0x90
[ 53.796982] ? __mod_node_page_state+0x8d/0xa0
[ 53.796986] ? __check_object_size+0xe7/0x240
[ 53.796989] ? __sys_sendto+0x229/0x290
[ 53.796991] ? rawv6_rcv_skb+0x160/0x160
[ 53.796993] __sys_sendto+0x229/0x290
[ 53.796996] ? __ia32_sys_getpeername+0x50/0x50
[ 53.796999] ? commit_creds+0x2de/0x520
[ 53.797002] ? security_capset+0x57/0x70
[ 53.797004] ? __x64_sys_capset+0x29f/0x3e0
[ 53.797007] ? __x64_sys_rt_sigsuspend+0xe0/0xe0
[ 53.797011] ? __do_page_fault+0x664/0x770
[ 53.797014] __x64_sys_sendto+0x74/0x90
[ 53.797017] do_syscall_64+0x69/0x160
[ 53.797019] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.797022] RIP: 0033:0x7f43b7a6714a
[ 53.797023] RSP: 002b:00007ffd891bd368 EFLAGS: 00000246 ORIG_RAX:
000000000000002c
[ 53.797026] RAX: ffffffffffffffda RBX: 00000000006129c0 RCX: 00007f43b7a6714a
[ 53.797028] RDX: 0000000000000040 RSI: 00000000006129c0 RDI: 0000000000000004
[ 53.797029] RBP: 00007ffd891be640 R08: 0000000000610940 R09: 000000000000001c
[ 53.797030] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000040
[ 53.797032] R13: 000000000060e6a0 R14: 0000000000008004 R15: 000000000040b661
[ 53.797171] Allocated by task 642:
[ 53.797460] kasan_kmalloc+0xa0/0xd0
[ 53.797463] kmem_cache_alloc+0xd2/0x1f0
[ 53.797465] getname_flags+0x40/0x210
[ 53.797467] user_path_at_empty+0x1d/0x40
[ 53.797469] do_faccessat+0x12a/0x320
[ 53.797471] do_syscall_64+0x69/0x160
[ 53.797473] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.797607] Freed by task 642:
[ 53.797869] __kasan_slab_free+0x130/0x180
[ 53.797871] kmem_cache_free+0xa8/0x230
[ 53.797872] filename_lookup+0x15b/0x230
[ 53.797874] do_faccessat+0x12a/0x320
[ 53.797876] do_syscall_64+0x69/0x160
[ 53.797878] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.798014] The buggy address belongs to the object at ffff88011975e600
which belongs to the cache names_cache of size 4096
[ 53.799043] The buggy address is located 1786 bytes inside of
4096-byte region [ffff88011975e600, ffff88011975f600)
[ 53.800013] The buggy address belongs to the page:
[ 53.800414] page:ffffea000465d600 count:1 mapcount:0
mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 53.801259] flags: 0x17fff0000008100(slab|head)
[ 53.801640] raw: 017fff0000008100 0000000000000000 0000000000000000
0000000100070007
[ 53.803147] raw: dead000000000100 dead000000000200 ffff88011b185a40
0000000000000000
[ 53.803787] page dumped because: kasan: bad access detected
[ 53.804384] Memory state around the buggy address:
[ 53.804788] ffff88011975eb80: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.805384] ffff88011975ec00: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.805979] >ffff88011975ec80: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.806577] ^
[ 53.807165] ffff88011975ed00: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.807762] ffff88011975ed80: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.808356] ==================================================================
[ 53.808949] Disabling lock debugging due to kernel taint
Fixes: 6c8702c60b88 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Signed-off-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Christophe Roullier says:
====================
net: ethernet: stmmac: add support for stm32mp1
Patches to have Ethernet support on stm32mp1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch describes syscon DT bindings.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Manage dwmac-4.20a version from synopsys
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add description for Ethernet MPU families fields
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Glue codes to support stm32mp157c device and stay
compatible with stm32 mcu familly
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add a documentation for ptp_qoriq dt-bindings.
The description for ptp_qoriq dt-bindings was actually moved
from Documentation/devicetree/bindings/net/fsl-tsec-phy.txt,
since gianfar_ptp driver was moved to ptp_qoriq driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Global variable gfar_phc_index was used to get and store
phc index through gianfar_ptp driver. However gianfar_ptp
had been renamed as ptp_qoriq for QorIQ common PTP driver.
This gfar_phc_index doesn't work any more, and the phc index
is stored in drvdata now. This patch is to support getting
phc index through ptp_qoriq drvdata.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to move some definitions in ptp_qoriq.c
to the header file.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gianfar_ptp was the PTP clock driver for 1588 timer
module of Freescale QorIQ eTSEC (Enhanced Three-Speed
Ethernet Controllers) platforms. Actually QorIQ DPAA
(Data Path Acceleration Architecture) platforms is
also using the same 1588 timer module in hardware.
This patch is to rework gianfar_ptp as QorIQ common
PTP driver to support both DPAA and eTSEC. Moved
gianfar_ptp.c to drivers/ptp/, renamed it as
ptp_qoriq.c, and renamed many variables. There were
not any function changes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixup the checksum for CHECKSUM_COMPLETE when pulling skbs on RX path.
Otherwise we get splats when tc mirred is used to redirect packets to ifb.
Before fix:
nic: hw csum failure
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add RTL8211B suspend / resume callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sridhar Samudrala says:
====================
Enable virtio_net to act as a standby for a passthru device
The main motivation for this patch is to enable cloud service providers
to provide an accelerated datapath to virtio-net enabled VMs in a
transparent manner with no/minimal guest userspace changes. This also
enables hypervisor controlled live migration to be supported with VMs that
have direct attached SR-IOV VF devices.
Patch 1 introduces a failover module that provides a generic interface for
paravirtual drivers to listen for netdev register/unregister/link change
events from pci ethernet devices with the same MAC and takeover their
datapath. The notifier and event handling code is based on the existing
netvsc implementation.
Patch 2 refactors netvsc to use the registration/notification framework
introduced by failover module.
Patch 3 introduces a net_failover driver that provides an automated
failover mechanism to paravirtual drivers via APIs to create and destroy
a failover master netdev and mananges a primary and standby slave netdevs
that get registered via the generic failover infrastructure.
Patch 4 introduces a new feature bit VIRTIO_NET_F_STANDBY to virtio-net
that can be used by hypervisor to indicate that virtio_net interface
should act as a standby for another device with the same MAC address.
Patch 5 extends virtio_net to use alternate datapath when available and
registered. When STANDBY feature is enabled, virtio_net driver uese the
net_failover API to create an additional 'failover' netdev that acts as
a master device and controls 2 slave devices. The original virtio_net
netdev is registered as 'standby' netdev and a passthru/vf device with
the same MAC gets registered as 'primary' netdev. Both 'standby' and
'failover' netdevs are associated with the same 'pci' device. The user
accesses the network interface via 'failover' netdev. The 'failover'
netdev chooses 'primary' netdev as default for transmits when it is
available with link up and running.
As this patch series is initially focusing on usecases where hypervisor
fully controls the VM networking and the guest is not expected to directly
configure any hardware settings, it doesn't expose all the ndo/ethtool ops
that are supported by virtio_net at this time. To support additional usecases,
it should be possible to enable additional ops later by caching the state
in failover netdev and replaying when the 'primary' netdev gets registered.
At the time of live migration, the hypervisor needs to unplug the VF device
from the guest on the source host and reset the MAC filter of the VF to
initiate failover of datapath to virtio before starting the migration. After
the migration is completed, the destination hypervisor sets the MAC filter
on the VF and plugs it back to the guest to switch over to VF datapath.
This patch is based on the discussion initiated by Jesse on this thread.
https://marc.info/?l=linux-virtualization&m=151189725224231&w=2
v12:
- Tested live migration with virtio-net/AVF(i40evf) configured in failover
mode while running iperf in background. Tried static ip and dhcp
configurations using 'network' scripts and Network Manager.
- Build tested netvsc module.
Updates:
- Extended generic failover module to do common functions like setting
FAILOVER_SLAVE flag, registering rx-handler and linking to upper dev in
the generic register/unregister handlers.
This required adding 3 additional failover ops pre_register, pre_unregister
and handle_frame. netvsc and net_failover drivers are updated to support
these ops.
v11:
- Split net_failover module into 2 components.
1. 'failover' module that provides generic failover infrastructure
to register a failover instance and listen for slave events.
2. 'net_failover' driver that provides APIs to create/destroy upper
netdev and supports 3-netdev model used by virtio-net.
- Added documentation
v10:
- fix net_failover_open() to update failover CARRIER correctly based on
standby and primary states.
- fix net_failover_handle_frame() to handle frames received on standby
when primary is present.
- replace netdev_upper_dev_link with netdev_master_upper_dev_link and
handle lower dev state changes.
- fix net_failver_create() and net_failover_register() interfaces to
use ERR_PTR and avoid arg **
- disable setting mac address when virtio-net in STANDBY mode
- document exported symbols
- added entry to MAINTAINERS file
v9:
Select NET_FAILOVER automatically when VIRTIO_NET/HYPERV_NET
are enabled. (stephen)
v8:
- Made the failover managment routines more robust by updating the feature
bits/other fields in the failover netdev when slave netdevs are
registered/unregistered. (mst)
- added support for handling vlans.
- Limited the changes in netvsc to only use the notifier/event/lookups
from the failover module. The slave register/unregister/link-change
handlers are only updated to use the getbymac routine to get the
upper netdev. There is no change in their functionality. (stephen)
- renamed structs/function/file names to use net_failover prefix. (mst)
v7
- Rename 'bypass/active/backup' terminology with 'failover/primary/standy'
(jiri, mst)
- re-arranged dev_open() and dev_set_mtu() calls in the register routines
so that they don't get called for 2-netdev model. (stephen)
- fixed select_queue() routine to do queue selection based on VF if it is
registered as primary. (stephen)
- minor bugfixes
v6 RFC:
Simplified virtio_net changes by moving all the ndo_ops of the
bypass_netdev and create/destroy of bypass_netdev to 'bypass' module.
avoided 2 phase registration(driver + instances).
introduced IFF_BYPASS/IFF_BYPASS_SLAVE dev->priv_flags
replaced mutex with a spinlock
v5 RFC:
Based on Jiri's comments, moved the common functionality to a 'bypass'
module so that the same notifier and event handlers to handle child
register/unregister/link change events can be shared between virtio_net
and netvsc.
Improved error handling based on Siwei's comments.
v4:
- Based on the review comments on the v3 version of the RFC patch and
Jakub's suggestion for the naming issue with 3 netdev solution,
proposed 3 netdev in-driver bonding solution for virtio-net.
v3 RFC:
- Introduced 3 netdev model and pointed out a couple of issues with
that model and proposed 2 netdev model to avoid these issues.
- Removed broadcast/multicast optimization and only use virtio as
backup path when VF is unplugged.
v2 RFC:
- Changed VIRTIO_NET_F_MASTER to VIRTIO_NET_F_BACKUP (mst)
- made a small change to the virtio-net xmit path to only use VF datapath
for unicasts. Broadcasts/multicasts use virtio datapath. This avoids
east-west broadcasts to go over the PCI link.
- added suppport for the feature bit in qemu
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
