| Age | Commit message (Collapse) | Author |
|---|
|
The vqmmc supply is not connected to bio supply on the BA16 module.
Hence remove vqmmc-supply property in usdhc3 node.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add SCFG MSI dts node and add msi-parent property to PCIe dts node
that points to the corresponding MSI node.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to Documentation/devicetree/bindings/net/fsl-fec.txt the polarity
of "phy-reset-gpios" is assumed to be active-low unless a separate property
"phy-reset-active-high" is available. So replace the inconsistent polarity
description to make the correct active-low reset behavior more obvious.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This commit adds support for Rev. B of a Zodiac Inflight Innovations
development board, mainly intended for DSA and ARINC 429 development
work.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing reg properties to AIPS bus and Cortex-A5's PMU unit.
This change avoids the following warnings:
Warning (unit_address_vs_reg): Node /soc/aips-bus@40000000 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@40080000 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@40080000/pmu@40089000
has a unit name, but no reg property
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The NAND flash memory populated on Colibri VF61 allows faster NAND
timings than the flash memory on VF50. Additionally, due to divider
limitations, VF61 did clock the flash even slower than VF50. Assign
the NFC clock in the module specific device trees vf500-colibri.dtsi
and vf610-colibri.dtsi respectively.
This increases raw read speed on Colibri VF61 by about 20%.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Vybrid based Colibri modules provide a on-module PHY which is
connected to the second FEC instance FEC1. Since the on-module
Ethernet port is considered as primary ethernet interface, alias
fec1 as ethernet0. This also makes sure that the first MAC address
provided by the boot loader gets assigned to the FEC instance used
for the on-module PHY.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Introduce imx6sx-sdb-sai.dts so that it is possible to use the
SAI interface.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Document the 'fsl,sdma-event-remap' property and provide an example of
its usage.
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Property 'dma-source' is not used anywhere, nor it is documented, so
let's just get rid of it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to sdma_peripheral_type in include/linux/platform_data/dma-imx.h
IMX_DMATYPE_SAI corresponds to index 24, so fix it accordingly.
Suggested-by: Zidan Wang <zidan.wang@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
pwm2 is provided on the BA16 Q7 module, but is not used on any
of the current configurations. However, future platforms may
utilize this device, so we are simply disabling the node rather
than removing it completely.
Signed-off-by: Justin Waters <justin.waters@timeys.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Based on i.MX6 SoloX with 1GB of RAM.
https://boundarydevices.com/product/nit6_solox-imx6/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It is preferred to use the panel compatible string rather than passing the
LCD timings in the device tree.
So pass the "hannstar,hsd100pxn1" compatible string to describe
the LVDS panel on this board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This baseboard can be used with all TX6 SoMs, but only a certain set
of combinations can be ordered by default. Add support for these
combinations in mainline, so that users can easily adopt their own
combination of SoM and baseboard themselves.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the following i.MX6 based modules from Ka-Ro
electronics GmbH:
TX6S-8034:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 256MiB DDR3 SDRAM
ROM 128MiB NAND Flash
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
TX6S-8035:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 512MiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
TX6U-8033:
Processor Freescale i.MX 6 Dual Lite, 800MHz
RAM 1GiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40°C/-25°C to 105°C Tj)
TX6Q-1036:
Processor Freescale i.MX 6Quad, 1GHz
RAM 1GB DDR3 SDRAM 64-bit
ROM 8GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range Extended Consumer Grade (-20°C to 105°C Tj)
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing pinctrl for the RTS/CTS lines to uart1 and set the
fsl,uart-has-rtscts property on all UARTs to enable support for HW
handshake.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the pinctrl setting for the board LED from the hoggrp node
to a separate node referenced by the LED driver, so that the pin is
free to be used for different purpose when the LED driver is disabled.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
DT maintainers don't like the 'simple-bus' container around the
regulator nodes. So remove it.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Based on i.MX6 Quad Plus with 4GB of RAM.
https://boundarydevices.com/product/nitrogen6max/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add mdio node and an appropriate PHY configuration to enable use of
the PHY interrupt for link status changes.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the function node around the pinctrl nodes that was obsoleted
by commit 5fcdf6a7ed95 ("pinctrl: imx: Allow parsing DT without
function nodes"), we can save this container node.
Also move the iomux node to the bottom of the file to improve
readability of the file.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The spidev driver doesn't like to be instantiated via a naked 'spidev'
compatible, though it is very convenient to invoke it this way without
a dedicated SPI device for basic functional testing.
Disable the spi node by default to silence the WARN_ON() from the
spidev driver, but leave the configuration intact otherwise.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add an empty line between properties and subnode in the clocks node.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the imx6*-tx6* files to this combination.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
mode
With SION set the level on such a pin is reported to the UART. So for
example when the CS5 pin is configured for GPIO mode and the level
changes this triggers an RTS interrupt on uart5.
Adding some severity to this issue: The imx uart driver currently
doesn't handle correctly irqs for changes on RI and DCD which are
enabled automatically when the respective UART is driven in DTE mode
(that is, has the fsl,dte-mode property set in the device tree). This
results in a stuck machine because the irq isn't cleared and so stalls
the CPU.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Apart from a few additions this also contains two fixes where the daisy
chain input selection register was missing. Moreover dropped _MUX from
some pins for consistency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Utilize the new PCIe Tx configuration to properly support the correct
values.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The TXUL-0010/-0011 modules are Computers On Module manufactured by
Ka-Ro electronics GmbH with the following characteristics:
Processor Freescale i.MX 6UltraLite MCIMX6G2, 528 MHz
RAM 256MB 16-bit DDR3 SDRAM
ROM 128MB NAND Flash (TXUL-0010) / 4GB eMMC (TXUL-0011)
Power supply Single 3.3 to 5V
Size 26mm SO-DIMM
Temp. Range -40°C to 85°C
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix following DTC warnings in SMDKv210 board:
Warning (unit_address_vs_reg): Node /soc/fimd@f8000000/display-timings/timing@0 has a unit name, but no reg property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Fix following DTC warnings in Exynos5440 boards:
Warning (unit_address_vs_reg): Node /pinctrl has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /rtc has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Fix following DTC warnings in Exynos5420 SMDK5420:
Warning (unit_address_vs_reg): Node /dp-controller@145B0000/display-timings/timing@0 has a unit name, but no reg property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Fix following DTC warnings in Exynos5420 Peach Pit:
Warning (unit_address_vs_reg): Node /dp-controller@145B0000/ports/port@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@12CD0000/lvds-bridge@48/ports/port@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@12CD0000/lvds-bridge@48/ports/port@1 has a unit name, but no reg property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Fix following DTC warnings in all Exynos542x/5800 boards:
Warning (unit_address_vs_reg): Node /video-phy@10040728 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /video-phy@10040714 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12000000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12000000/dwc3 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /usb@12400000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12400000/dwc3 has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Fix following DTC warnings in all Exynos5250 boards:
Warning (unit_address_vs_reg): Node /dp-controller@145B0000/display-timings/timing@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12000000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12000000/dwc3 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /hdmi has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /mixer has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /video-phy@10040720 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixed-regulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixed-regulator@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixed-regulator@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@12C70000/trackpad has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /i2c@12CD0000/lvds-bridge@20/ports/port@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@12CD0000/lvds-bridge@20/ports/port@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c-arbitrator/i2c@0/embedded-controller has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /i2c-arbitrator/i2c@0/power-regulator has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /i2c@12CA0000/embedded-controller has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Fix following DTC warnings in Exynos4x12 boards:
Warning (unit_address_vs_reg): Node /camera/fimc-is@12000000/pmu has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Fix following DTC warnings in Trats2 board:
Warning (unit_address_vs_reg): Node /i2c-gpio-1/max77693@66/regulators/ESAFEOUT1@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c-gpio-1/max77693@66/regulators/ESAFEOUT2@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c-gpio-1/max77693@66/regulators/CHARGER@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /thermistor-ap@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /thermistor-battery@1 has a unit name, but no reg property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Fix following DTC warnings in all Exynos4 boards:
Warning (unit_address_vs_reg): Node /soc/video-phy@10020710 has a unit name, but no reg property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Fix following DTC warnings in Exynos3250 boards:
Warning (unit_address_vs_reg): Node /soc/video-phy@10020710 has a unit name, but no reg property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Fix following DTC warnings in cros-adc-thermistors:
Warning (unit_address_vs_reg): Node /adc@12D10000/ncp15wb473@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /adc@12D10000/ncp15wb473@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /adc@12D10000/ncp15wb473@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /adc@12D10000/ncp15wb473@6 has a unit name, but no reg property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Add vmmc and vqmmc supplies from MF circuit sheets for eMMC and SD on
odroid XU3 and XU4 to avoid warnings:
dwmmc_exynos 12200000.mmc: Looking up vmmc-supply property in node /mmc@12200000 failed
Also remove their always_on properties so the regulators could be
disabled when not used.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Topic branch for Device Tree changes for Exynos 3250 for v4.7:
Merge necessary new clocks from Sylwester (used by new board) and add support
for Exynos3250-based Artik5 board.
|
|
On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.
For NAND we don't use GPMC wait pin monitoring but
get the NAND Ready/Busy# status using GPIOlib.
GPMC driver provides the WAIT0 pin status over GPIOlib.
Read speed increases from 13212 KiB/ to 15753 KiB/s
and write speed was unchanged at 4404 KiB/s.
Measured using mtd_speedtest.ko on omap3-beagle-c4.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.
For NAND we don't use GPMC wait pin monitoring but
get the NAND Ready/Busy# status using GPIOlib.
GPMC driver provides the WAIT0 pin status over GPIOlib.
Read speed increases from 7869 KiB/ to 8875 KiB/s
and write speed was unchanged at 5100 KiB/s.
Measured using mtd_speedtest.ko on am335x-evm.
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.
For NAND we don't use GPMC wait pin monitoring but
get the NAND Ready/Busy# status using GPIOlib.
GPMC driver provides the WAIT0 pin status over GPIOlib.
Read speed increases from 16516 KiB/ to 18813 KiB/s
and write speed was unchanged at 9941 KiB/s.
Measured using mtd_speedtest.ko.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On these boards NAND ready pin status is avilable over
GPMC_WAIT0 pin.
Read speed increases from 13768 KiB/ to 17246 KiB/s.
Write speed was unchanged at 7123 KiB/s.
Measured using mtd_speedtest.ko.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
GPMC driver provides GPI support for the GPMC_WAIT pins.
Mark it gpio controller capable.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
GPMC driver provides GPI support for the GPMC_WAIT pins.
Mark it gpio controller capable.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
