| Age | Commit message (Collapse) | Author |
|---|
|
When support for PMICs without compatibles was removed in
commit f736d2c0caa8 ("mfd: sec: Remove PMICs without compatibles"),
sec_regmap_config effectively became an orphan, because S5M8763X was
the only user left of it before removal, using the default: case of the
switch statement.
When s2dos05 and s2mpu05 support was added in commit bf231e5febcf
("mfd: sec-core: Add support for the Samsung s2dos05") and commit
ed33479b7beb ("mfd: sec: Add support for S2MPU05 PMIC"), they ended up
using that orphaned regmap_config in a non-obvious way due to the
default: case of the device type switch matching statement taking
effect again.
To make things more obvious, and to help the reader of this code while
reasoning about what the intention might be here, and to ensure future
additions to support new devices in this driver don't forget to add a
regmap config, add an explicit regmap config for these two devices, and
completely remove the generic regmap config as it becomes an orphan
again that shouldn't be used by any device.
Note that this commit doesn't fix the issue that s2dos05_regmap_config
ands2mpu05_regmap_config really are incomplete, but I have no
documentation on them.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-14-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
dev_err_probe() exists to simplify code and harmonise error messages,
there's no reason not to use it here.
While at it, harmonise some error messages.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-13-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Sort struct of_device_id entries and the device type switch in _probe()
alphabetically, which makes it easier to find the right place where to
insert new entries in the future.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-12-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Rectify a couple of alignment problems reported by Checkpatch.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-11-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
There is no reason to have these two kernel modules separate. Having
them merged into one kernel module also slightly reduces memory
consumption and module load times a little.
mapped size (lsmod):
before: after:
sec_core 20480 sec_core 24576
sec_irq 16384
----------------
total 36864
Section sizes (size -A):
before: after:
sec_core 6780 sec_core 13239
sec_irq 8046
----------------
Total 14826
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-10-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for Samsung's S2MPG10 PMIC, which is a Power Management IC
for mobile applications with buck converters, various LDOs, power
meters, RTC, clock outputs, and additional GPIOs interfaces.
Contrary to existing Samsung S2M series PMICs supported, communication
is not via I2C, but via the Samsung ACPM firmware.
This commit adds the core driver.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-9-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
As a preparation for adding support for Samsung's S2MPG10, which is
connected via SPEEDY / ACPM rather than I2C, split out (move) all
I2C-specific driver code into its own kernel module, sec-i2c, and
make the existing sec-core module be just the transport-agnostic core
driver kernel module.
At the same time, update all defconfigs that reference the old kconfig
symbol name.
While at it, also update file header comments and module description(s)
to drop references to 'mfd', and update comments to be C-style, not
C++.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-8-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
sec_irq_init() is an internal API for the core driver, and doesn't
belong into the public header.
Due to an upcoming split of the driver into a core and i2c driver,
we'll also be adding more internal APIs, which again shouldn't be in
the public header.
Move it into a new internal include.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-7-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
This driver misses to include some of the respective headers of some of
the APIs used. It also includes headers that aren't needed (e.g. due to
previous driver rework where includes weren't updated).
It is good practice to directly include all headers used, which avoids
implicit dependencies and spurious build breakage if someone rearranged
headers, as this could cause the implicit includes to be dropped.
Include the relevant headers explicitly and drop superfluous ones.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-6-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Sorting headers alphabetically helps locating duplicates, and makes it
easier to figure out where to insert new headers.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-5-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
sec_irq_resume() was removed in commit 6445b84abf91 ("mfd: Add s2mps11
irq driver") and sec_irq_exit() in commit 3dc6f4aaafbe ("mfd: sec: Use
devm_mfd_add_devices and devm_regmap_add_irq_chip") while the
prototypes were left. They should be removed.
Do so.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-4-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The Samsung S2MPG10 PMIC is similar to the existing PMICs supported by
this binding.
It is a Power Management IC for mobile applications with buck
converters, various LDOs, power meters, RTC, clock outputs, and
additional GPIOs interfaces.
Unlike other Samsung PMICs, communication is not via I2C, but via the
Samsung ACPM firmware, it therefore doesn't need a 'reg' property but
needs to be a child of the ACPM firmware node instead.
S2MPG10 can also act as a system power controller allowing
implementation of a true cold-reset of the system.
Support for the other components like regulators and power meters will
be added in subsequent future patches.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-1-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add SAMA7D65 SECUMOD compatible string to DT bindings documentation.
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/2fdd14313d9cf008dbc4a63a91ba0cb5cf372ad6.1744666011.git.Ryan.Wanner@microchip.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Convert Microchip AT91 secumod to YAML format.
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/a999a719a652ec834f1176d69a3e9b207cbd63e6.1744666011.git.Ryan.Wanner@microchip.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add SAMA7D65 GPBR compatible to DT bindings documentation.
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/ddbcb306699b8c09f3210d714c0701afa1a7cb96.1744666011.git.Ryan.Wanner@microchip.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250407-gpiochip-set-rv-mfd-v1-3-43f4d86d01d1@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250407-gpiochip-set-rv-mfd-v1-2-43f4d86d01d1@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250407-gpiochip-set-rv-mfd-v1-1-43f4d86d01d1@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The "id" member of the bcm590xx struct is unused and will be confusing
once we add an actual PMU ID storage value. Drop it; a replacement
will be introduced in a future commit.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250316-bcm59054-v7-4-4281126be1b8@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Commit 835a0c10d33b ("leds: Rename simple directory to simatic") renames
the driver's directory to drivers/leds/simatic, but misses to adjust the
SIEMENS IPC LED DRIVERS section in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken reference. Adjust the file entry to this renaming.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Link: https://lore.kernel.org/r/20250325092159.213463-1-lukas.bulwahn@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The I2C core now provides a debugfs entry for each client. Let this
driver use it instead of the root directory. Further improvements by
this change: automatic support of multiple instances.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250318091234.22170-1-wsa+renesas@sang-engineering.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The I2C core now provides a debugfs entry for each client. Let this
driver use it instead of the custom directory in debugfs root. Further
improvements by this change: automatic clean up on removal, support of
multiple instances.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250318091426.22258-2-wsa+renesas@sang-engineering.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
'ib-mfd-gpio-nvmem-6.16', 'ib-mfd-regulator-6.16' and 'ib-mfd-regulator-6.16-1' into ibs-for-mfd-merged
|
|
The BCM59056 and BCM59054 are very similar in terms of regulators. Add
the register definitions for the BCM59054 and enable support for it in
the driver.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Reviewed-by: Mark Brown <brooni@kernel.org>
Link: https://lore.kernel.org/r/20250515-bcm59054-v9-8-14ba0ea2ea5b@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Previously, the driver used the BCM590XX prefix for register data
specific to the BCM59056. As we will be introducing other regulators
to this driver as well, make the BCM59056-specific values use the
BCM59056 prefix.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250515-bcm59054-v9-7-14ba0ea2ea5b@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Instead of filling in the regulator description programatically,
store the data in a struct. This will make it a bit nicer to
introduce support for other BCM590xx chips besides the BCM59056.
To do this, add a new struct type, bcm590xx_reg_data, to store
all of the necessary information. Drop the old IS_LDO, IS_GPLDO...
macros in favor of the "type" field in this struct. Adapt the
old bcm590xx_reg struct to the new types.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250515-bcm59054-v9-6-14ba0ea2ea5b@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Instead of calling dev_err() and returning PTR_ERR(...) separately, use
a single "return dev_err_probe" statement.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250515-bcm59054-v9-5-14ba0ea2ea5b@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The BCM590xx PMUs have two I2C registers for reading the PMU ID
and revision. The revision is useful for subdevice drivers, since
different revisions may have slight differences in behavior (for
example - BCM59054 has different regulator configurations for
revision A0 and A1).
Check the PMU ID register and make sure it matches the DT compatible.
Fetch the digital and analog revision from the PMUREV register
so that it can be used in subdevice drivers.
Also add some known revision values to bcm590xx.h, for convenience
when writing subdevice drivers.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Link: https://lore.kernel.org/r/20250515-bcm59054-v9-4-14ba0ea2ea5b@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The BCM59054 is another chip from the BCM590xx line of PMUs, commonly
used on devices with the BCM21664/BCM23550 chipsets.
Prepare the BCM590xx driver for supporting other devices by adding the
PMUID register values for supported chip types and store them in the
MFD data struct as "pmu_id". (These will be checked against the actual
PMUID register values in a later commit.)
Then, add a DT compatible for the BCM59054, and provide the PMU ID as
OF match data.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Link: https://lore.kernel.org/r/20250515-bcm59054-v9-3-14ba0ea2ea5b@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The BCM59054 MFD is fairly similar to the BCM59056, and will use
the same driver. Add compatible and specify the allowed regulator
nodes.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Reviewed-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Link: https://lore.kernel.org/r/20250515-bcm59054-v9-2-14ba0ea2ea5b@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Convert devicetree bindings for the Broadcom BCM59056 PMU MFD from
TXT to YAML format. This patch does not change any functionality;
the bindings remain the same.
The bindings have been split into two parts: the MFD binding and
a separate binding for the regulator node, to simplify the addition
of other models later (which have different regulators).
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Reviewed-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Link: https://lore.kernel.org/r/20250515-bcm59054-v9-1-14ba0ea2ea5b@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for STM32MP25 SoC. A new compatible has been added to the
dt-bindings. It represents handle new features, registers and bits
diversity.
It isn't used currently in the driver, as matching is done by retrieving
MFD parent data.
New dedicated capture/compare channels has been added: e.g. a new compare
register for channel 2. Some controls (polarity / cc channel enable) are
handled in CCMR register on this new variant (instead of wavepol bit).
So, Low-power timer can now have up to two PWM outputs. Use device data
from the MFD parent to configure the number of PWM channels e.g. 'npwm'.
Update current get_state() and apply() ops to support either:
- one PWM channel (as on older revision, or LPTIM5 on STM32MP25)
- two PWM channels (e.g. LPTIM1/2/3/4 on STM32MP25 that has the full
feature set)
Introduce new routines to manage common prescaler, reload register and
global enable bit.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Uwe Kleine-König <ukleinek@kernel.org>
Link: https://lore.kernel.org/r/20250429125133.1574167-5-fabrice.gasnier@foss.st.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
On stm32mp25, DIER (former IER) must only be modified when the lptimer
is enabled. On earlier SoCs, it must be only be modified when it is
disabled. There's also a new DIEROK flag, to ensure register access
has completed.
Add a new "set_evt" routine to be used on stm32mp25, called depending
on the version register, read by the MFD core (LPTIM_VERR).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20250429125133.1574167-4-fabrice.gasnier@foss.st.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for STM32MP25 SoC.
A new hardware configuration register (HWCFGR2) has been added, to gather
number of capture/compare channels, autonomous mode and input capture
capability. The full feature set is implemented in LPTIM1/2/3/4. LPTIM5
supports a smaller set of features. This can now be read from HWCFGR
registers.
Add new registers to the stm32-lptimer.h: CCMR1, CCR2, HWCFGR1/2 and VERR.
Update the stm32_lptimer data struct so signal the number of
capture/compare channels to the child devices.
Also Remove some unused bit masks (CMPOK_ARROK / CMPOKCF_ARROKCF).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250429125133.1574167-3-fabrice.gasnier@foss.st.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add a new stm32mp25 compatible to stm32-lptimer dt-bindings, to support
STM32MP25 SoC. Some features has been updated or added to the low-power
timer:
- new capture compare channels
- up to two PWM channels
- PWM input capture
- peripheral interconnect in stm32mp25 has been updated (new triggers).
- registers/bits has been added or revisited (IER access).
So introduce a new compatible to handle this diversity.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250429125133.1574167-2-fabrice.gasnier@foss.st.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The Maxim MAX77759 is a companion PMIC for USB Type-C applications and
includes Battery Charger, Fuel Gauge, temperature sensors, USB Type-C
Port Controller (TCPC), NVMEM, and a GPIO expander.
This driver exposes the non volatile memory using the platform device
registered by the core MFD driver.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Acked-by: Srinivas Kandagatla <srini@kernel.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250509-max77759-mfd-v10-3-962ac15ee3ef@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The Maxim MAX77759 is a companion PMIC for USB Type-C applications and
includes Battery Charger, Fuel Gauge, temperature sensors, USB Type-C
Port Controller (TCPC), NVMEM, and a GPIO expander.
This driver supports the GPIO functions using the platform device
registered by the core MFD driver.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250509-max77759-mfd-v10-2-962ac15ee3ef@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The Maxim MAX77759 is a companion PMIC for USB Type-C applications and
includes Battery Charger, Fuel Gauge, temperature sensors, USB Type-C
Port Controller (TCPC), NVMEM, and a GPIO expander.
Fuel Gauge and TCPC have separate and independent I2C addresses,
register maps, and interrupt lines and are therefore excluded from the
MFD core device driver here.
The GPIO and NVMEM interfaces are accessed via specific commands to the
built-in microprocessor. This driver implements an API that client
drivers can use for accessing those.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250509-max77759-mfd-v10-1-962ac15ee3ef@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The Maxim MAX77759 is a companion PMIC for USB Type-C applications and
includes Battery Charger, Fuel Gauge, temperature sensors, USB Type-C
Port Controller (TCPC), NVMEM, and a GPIO expander.
This describes the top-level device.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250325-max77759-mfd-v6-3-c0870ca662ba@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The Maxim MAX77759 is a companion PMIC for USB Type-C applications and
includes Battery Charger, Fuel Gauge, temperature sensors, USB Type-C
Port Controller (TCPC), NVMEM, and a GPIO expander.
This describes its storage module (NVMEM).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250325-max77759-mfd-v6-2-c0870ca662ba@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The Maxim MAX77759 is a companion PMIC for USB Type-C applications and
includes Battery Charger, Fuel Gauge, temperature sensors, USB Type-C
Port Controller (TCPC), NVMEM, and a GPIO expander.
This describes its GPIO module.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250325-max77759-mfd-v6-1-c0870ca662ba@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into ib-firmware-mfd-6.16
Samsung SoC drivers for v6.16
Several improvements to Exynos ACPM (Alive Clock and Power Manager)
driver:
1. Handle communication timeous better.
2. Avoid sleeping, so users (PMIC) can still transfer during system
shutdown.
3. Fix reading longer messages from them firmware.
4. Deferred probe improvements.
5. Model the user of ACPM - PMIC - a as child device and export
devm_acpm_get_by_node() for such use case.
|
|
Correct kerneldoc warnings after commit a8dc26a0ec43 ("firmware:
exynos-acpm: introduce devm_acpm_get_by_node()") changed the function
prototype:
exynos-acpm.c:672: warning: Function parameter or struct member 'acpm_np' not described in 'acpm_get_by_node'
exynos-acpm.c:672: warning: expecting prototype for acpm_get_by_phandle(). Prototype was for acpm_get_by_node() instead
While touching the lines, change the name of device_node pointer to
'np' to match convention.
Fixes: a8dc26a0ec43 ("firmware: exynos-acpm: introduce devm_acpm_get_by_node()")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504222051.7TqaSQ48-lkp@intel.com/
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20250424203308.402168-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Add the include/linux/mfd/rohm-bd96802.h to the list of the ROHM PMIC
specific files maintained by the undersigned.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/872fdf7c24d1ff4379d1234f03766bda64c5c5b4.1744090658.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The ROHM BD96806 is from the software perspective almost identical to
the ROHM BD96802. The main difference is different voltage tuning
ranges.
Add support differentiating these PMICs and provide correct voltages
for both models.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/5d15660e0e71c70fda8df1694bec0e4fba7f251e.1744090658.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The ROHM BD96806 is from the software perspective almost identical to
the ROHM BD96802. The main difference is different voltage tuning
ranges. Add support differentiating these PMICs based on the compatible,
and invoking the regulator driver with correct IC type.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/ccc95ae33613648fdcba08915777d945412ac5c4.1744090658.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The ROHM BD96805 is from the software perspective almost identical to
the ROHM BD96801. The main difference is different voltage tuning
ranges.
Add support differentiating these PMICs and provide correct voltages
for both models.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/eab1369557b14a9762c41a5429d1ac87a4644d9e.1744090658.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The ROHM BD96805 is from the software perspective almost identical to
the ROHM BD96801. The main difference is different voltage tuning
ranges. Add support differentiating these PMICs based on the compatible,
and invoking the regulator driver with correct IC type.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/8680097dc083f191bea56d3ac7c6fe5c005644ec.1744090658.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The ROHM BD96802 PMIC is primarily intended to be used as a companion
PMIC extending the capabilities of the BD96802 but it can be used on
it's own as well. When used as a companion PMIC, the start-up and
shut-down sequences are usually intitiated by the master PMIC using IF
pins.
The BD96802 looks from the digital interface point of view pretty much
like a reduced version of BD96801. It includes only 2 BUCKs and provides
the same error protection/detection mechanisms as the BD96801. Also, the
voltage control logic is same up to the register addresses.
Add support for controlling BD96802 using the BD96801 driver.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/2fb2d0d4997c32d18bfa32cea4564352c00eebc8.1744090658.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The ROHM BD96802 PMIC looks from software point of view a lot like ROHM
BD96801 PMIC. Just with reduced number of voltage rails. Both PMICs
provide two physical IRQ lines referred as INTB and ERRB and contain
blocks implementing regulator controls and a weatchdog. Hence it makes
sense to use same MFD core for both PMICs.
Add support for ROHM BD96802 scalable companion PMIC to the BD96801
core driver.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/05957d194425a79a4f35f287695c3d9ca2ed1ae2.1744090658.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
