summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2025-03-27Merge branch 'pci/controller/cadence'Bjorn Helgaas
- Correct MSG TLP generation so endpoint can generate INTx messages (Hans Zhang) * pci/controller/cadence: PCI: cadence-ep: Fix the driver to send MSG TLP for INTx without data payload
2025-03-27Merge branch 'pci/controller/brcmstb'Bjorn Helgaas
- Add missing of_node refcount release after of_parse_phandle() (Stanimir Varbanov) - Add BCM2712 MSI-X DT binding and interrupt controller drivers (Stanimir Varbanov) - Add brcmstb softdep on irq_bcm2712_mip MIP MSI-X interrupt controller driver to ensure that it is loaded first (Stanimir Varbanov) - Add struct brcm_pcie pointer to pcie_cfg_data so we can reference the pcie_cfg_data directly instead of copying it to brcm_pcie (Stanimir Varbanov) - Expand inbound window map to 64GB so it can accommodate BCM2712 (Stanimir Varbanov) - Add BCM2712 support and DT updates (Stanimir Varbanov) - Apply link speed restriction before bringing link up, not after (Jim Quinlan) - Update Max Link Speed in Link Capabilities via the internal writable register, not the read-only config register (Jim Quinlan) - Handle regulator_bulk_get() error to avoid panic when we call regulator_bulk_free() later (Jim Quinlan) - Disable regulators only when removing the bus immediately below a Root Port because we don't support regulators deeper in the hierarchy (Jim Quinlan) - Consistently use config access index/data register offsets from the SoC-specific pcie_offsets[] table (Jim Quinlan) - Update MDIO register fields that reduced CMD from 12 bits to 1 and widened PORT from 4 bits to 5 and split it into two parts (Jim Quinlan) - Make const read-only arrays static (Colin Ian King) * pci/controller/brcmstb: PCI: brcmstb: Make const read-only arrays static PCI: brcmstb: Make irq_domain_set_info() parameter cast explicit PCI: brcmstb: Make two changes in MDIO register fields PCI: brcmstb: Use same constant table for config space access PCI: brcmstb: Fix potential premature regulator disabling PCI: brcmstb: Fix error path after a call to regulator_bulk_get() PCI: brcmstb: Do not assume that register field starts at LSB PCI: brcmstb: Use internal register to change link capability PCI: brcmstb: Set generation limit before PCIe link up PCI: brcmstb: Add BCM2712 support PCI: brcmstb: Expand inbound window size up to 64GB PCI: brcmstb: Reuse pcie_cfg_data structure PCI: brcmstb: Add a softdep to MIP MSI-X driver irqchip: Add Broadcom BCM2712 MSI-X interrupt controller dt-bindings: PCI: brcmstb: Update bindings for PCIe on BCM2712 dt-bindings: interrupt-controller: Add BCM2712 MSI-X bindings PCI: brcmstb: Fix missing of_node_put() in brcm_pcie_probe()
2025-03-27Merge branch 'pci/controller/amd-mdb'Bjorn Helgaas
- Add DT binding and driver for AMD MDB (Multimedia DMA Bridge) (Thippeswamy Havalige) * pci/controller/amd-mdb: PCI: amd-mdb: Add AMD MDB Root Port driver dt-bindings: PCI: amd-mdb: Add AMD Versal2 MDB PCIe Root Port Bridge dt-bindings: PCI: dwc: Add AMD Versal2 MDB SLCR support
2025-03-27Merge branch 'pci/controller/altera'Bjorn Helgaas
- Add DT binding for Agilex family (P-Tile, F-Tile, R-Tile) (Matthew Gerlach) - Add driver support for Agilex family (P-Tile, F-Tile, R-Tile) (D M, Sharath Kumar) * pci/controller/altera: PCI: altera: Add Agilex support dt-bindings: PCI: altera: Add binding for Agilex
2025-03-27Merge branch 'pci/scoped-cleanup'Bjorn Helgaas
- Use for_each_available_child_of_node_scoped() to simplify apple, kirin, mediatek, mt7621, tegra drivers (Zhang Zekun) * pci/scoped-cleanup: PCI: tegra: Use helper function for_each_child_of_node_scoped() PCI: apple: Use helper function for_each_child_of_node_scoped() PCI: mt7621: Use helper function for_each_available_child_of_node_scoped() PCI: mediatek: Use helper function for_each_available_child_of_node_scoped() PCI: kirin: Tidy up _probe() related function with dev_err_probe() PCI: kirin: Use helper function for_each_available_child_of_node_scoped()
2025-03-27Merge branch 'pci/epf-mhi'Bjorn Helgaas
- Update SA8775P device ID (Mrinmay Sarkar) * pci/epf-mhi: PCI: epf-mhi: Update device ID for SA8775P
2025-03-27Merge branch 'pci/endpoint-test'Bjorn Helgaas
- Fix endpoint BAR testing so the test can skip disabled BARs instead of reporting them as failures (Niklas Cassel) - Verify that pci_endpoint interrupt tests set the correct IRQ type (Kunihiko Hayashi) - Fix interpretation of pci_endpoint_test_bars_read_bar() error returns (Niklas Cassel) - Fix potential string truncation in pci_endpoint_test_probe() (Niklas Cassel) - Increase endpoint test BAR size variable to accommodate BARs larger than INT_MAX (Niklas Cassel) - Release IRQs to avoid leak in pci_endpoint interrupt tests (Kunihiko Hayashi) - Log the correct IRQ type when pci_endpoint IRQ request test fails (Kunihiko Hayashi) - Remove pci_endpoint_test irq_type and no_msi globals; instead use test->irq_type (Kunihiko Hayashi) - Remove unnecessary use of managed IRQ functions in pci_endpoint_test (Kunihiko Hayashi) - Add and use IRQ_TYPE_* defines in pci_endpoint_test (Niklas Cassel) - Add struct pci_epc_features.intx_capable and note that RK3568 and RK3588 can't raise INTx interrupts (Niklas Cassel) - Expose supported IRQ types in CAPS so pci_endpoint_test can set appropriate type (Niklas Cassel) - Add PCITEST_IRQ_TYPE_AUTO to pci_endpoint_test for cases where the IRQ type doesn't matter (Niklas Cassel) * pci/endpoint-test: misc: pci_endpoint_test: Add support for PCITEST_IRQ_TYPE_AUTO PCI: endpoint: pci-epf-test: Expose supported IRQ types in CAPS register PCI: dw-rockchip: Endpoint mode cannot raise INTx interrupts PCI: endpoint: Add intx_capable to epc_features struct selftests: pci_endpoint: Use IRQ_TYPE_* defines from UAPI header misc: pci_endpoint_test: Use IRQ_TYPE_* defines from UAPI header PCI: endpoint: pcitest: Add IRQ_TYPE_* defines to UAPI header misc: pci_endpoint_test: Do not use managed IRQ functions misc: pci_endpoint_test: Remove global 'irq_type' and 'no_msi' misc: pci_endpoint_test: Fix 'irq_type' to convey the correct type misc: pci_endpoint_test: Fix displaying 'irq_type' after 'request_irq' error misc: pci_endpoint_test: Avoid issue of interrupts remaining after request_irq error misc: pci_endpoint_test: Handle BAR sizes larger than INT_MAX misc: pci_endpoint_test: Give disabled BARs a distinct error code misc: pci_endpoint_test: Fix potential truncation in pci_endpoint_test_probe() misc: pci_endpoint_test: Fix pci_endpoint_test_bars_read_bar() error handling selftests: pci_endpoint: Add GET_IRQTYPE checks to each interrupt test selftests: pci_endpoint: Skip disabled BARs
2025-03-27Merge branch 'pci/endpoint'Bjorn Helgaas
- Convert PCI device data so pci-epf-test works correctly on big-endian endpoint systems (Niklas Cassel) - Add BAR_RESIZABLE type to endpoint framework (Niklas Cassel) - Add pci_epc_bar_size_to_rebar_cap() to convert a size to the Resizable BAR Capability so endpoint drivers can configure what the Capability register advertises (Niklas Cassel) - Add DWC core support for EPF drivers to set BAR_RESIZABLE type and size via dw_pcie_ep_set_bar() (Niklas Cassel) - Describe TI AM65x (keystone) BARs 2 and 5 as Resizable, not Fixed (Niklas Cassel) - Reduce TI AM65x (keystone) BAR alignment requirement from 1MB to 64KB (Niklas Cassel) - Describe Rockchip rk3568 and rk3588 BARs as Resizable, not Fixed (Niklas Cassel) - Drop unused devm_pci_epc_destroy() (Zijun Hu) - Fix pci-epf-test double free that causes an oops if the host reboots and PERST# deassertion restarts endpoint BAR allocation (Christian Bruel) - Drop dw_pcie_ep_find_ext_capability() and use dw_pcie_find_ext_capability() instead (Niklas Cassel) * pci/endpoint: PCI: dwc: ep: Remove superfluous function dw_pcie_ep_find_ext_capability() PCI: endpoint: pci-epf-test: Fix double free that causes kernel to oops PCI: endpoint: Remove unused devm_pci_epc_destroy() PCI: dw-rockchip: Describe Resizable BARs as Resizable BARs PCI: keystone: Specify correct alignment requirement PCI: keystone: Describe Resizable BARs as Resizable BARs PCI: dwc: ep: Allow EPF drivers to configure the size of Resizable BARs PCI: dwc: ep: Move dw_pcie_ep_find_ext_capability() PCI: endpoint: Add pci_epc_bar_size_to_rebar_cap() PCI: endpoint: Allow EPF drivers to configure the size of Resizable BARs PCI: endpoint: pci-epf-test: Handle endianness properly
2025-03-27Merge branch 'pci/dt-bindings'Bjorn Helgaas
- Add qcom,pcie-ipq5332 binding (Varadarajan Narayanan) - Convert fsl,mpc83xx-pcie binding to YAML (J. Neuschäfer) - Add qcom i.MX8QM and i.MX8QXP/DXP optional DMA interrupt (Alexander Stein) - Drop deprecated layerscape 'num-ib-windows' and 'num-ob-windows' from example (Krzysztof Kozlowski) - Drop unnecessary layerscape 'status' from example (Krzysztof Kozlowski) - Add common pci-ep-bus.yaml schema for exporting several peripherals of a single PCI function via devicetree (Andrea della Porta) * pci/dt-bindings: dt-bindings: PCI: Add common schema for devices accessible through PCI BARs dt-bindings: PCI: fsl,layerscape-pcie-ep: Drop unnecessary status from example dt-bindings: PCI: fsl,layerscape-pcie-ep: Drop deprecated windows dt-bindings: PCI: fsl,imx6q-pcie: Add optional DMA interrupt dt-bindings: PCI: Convert fsl,mpc83xx-pcie to YAML dt-bindings: PCI: qcom: Document the IPQ5332 PCIe controller
2025-03-27Merge branch 'pci/devtree-create'Bjorn Helgaas
- Add device_add_of_node() to set dev->of_node and dev->fwnode only if they haven't been set already (Herve Codina) - Allow of_pci_set_address() to set the DT address property for root bus nodes, where there is no PCI bridge to supply the PCI bus/device/function part of the property (Herve Codina) - Create DT nodes for PCI host bridges to enable loading device tree overlays to create platform devices for PCI devices that have several features that require multiple drivers (Herve Codina) * pci/devtree-create: PCI: of: Create device tree PCI host bridge node PCI: of_property: Constify parameter in of_pci_get_addr_flags() PCI: of_property: Add support for NULL pdev in of_pci_set_address() PCI: of: Use device_{add,remove}_of_node() to attach of_node to existing device driver core: Introduce device_{add,remove}_of_node()
2025-03-27Merge branch 'pci/resource'Bjorn Helgaas
- Use pci_resource_n() to simplify BAR/window resource lookup (Ilpo Järvinen) - Fix typo that repeatedly distributed resources to a bridge instead of iterating over subordinate bridges, which resulted in too little space to assign some BARs (Kai-Heng Feng) - Relax bridge window tail sizing for optional resources, e.g., IOV BARs, to avoid failures when removing and re-adding devices (Ilpo Järvinen) - Fix a double counting error for I/O resources, as we previously did for memory resources (Ilpo Järvinen) - Use resource_set_{range,size}() helpers in more places (Ilpo Järvinen) - Add pci_resource_is_iov() to identify IOV resources (Ilpo Järvinen) - Add pci_resource_num() to look up the BAR number from the resource pointer (Ilpo Järvinen) - Add restore_dev_resource() to simplify code that resources saved device resources (Ilpo Järvinen) - Allow drivers to enable devices even if we haven't assigned optional IOV resources to them (Ilpo Järvinen) - Improve debug output during resource reallocation (Ilpo Järvinen) - Rework handling of optional resources (IOV BARs, ROMs) to reduce failures if we can't allocate them (Ilpo Järvinen) - Move declarations of pci_rescan_bus_bridge_resize(), pci_reassign_bridge_resources(), and CardBus-related sizes from include/linux/pci.h to drivers/pci/pci.h since they're not used outside the PCI core (Ilpo Järvinen) - Make pci_setup_bridge() static (Ilpo Järvinen) - Fix a NULL dereference in the SR-IOV VF creation error path (Shay Drory) - Fix s390 mmio_read/write syscalls, which didn't cause page faults in some cases, which broke vfio-pci lazy mapping on first access (Niklas Schnelle) - Add pdev->non_mappable_bars to replace CONFIG_VFIO_PCI_MMAP, which was disabled only for s390 (Niklas Schnelle) - Support mmap of PCI resources on s390 except for ISM devices (Niklas Schnelle) * pci/resource: s390/pci: Support mmap() of PCI resources except for ISM devices s390/pci: Introduce pdev->non_mappable_bars and replace VFIO_PCI_MMAP s390/pci: Fix s390_mmio_read/write syscall page fault handling PCI: Fix NULL dereference in SR-IOV VF creation error path PCI: Move cardbus IO size declarations into pci/pci.h PCI: Make pci_setup_bridge() static PCI: Move resource reassignment func declarations into pci/pci.h PCI: Move pci_rescan_bus_bridge_resize() declaration to pci/pci.h PCI: Fix BAR resizing when VF BARs are assigned PCI: Do not claim to release resource falsely PCI: Increase Resizable BAR support from 512 GB to 128 TB PCI: Rework optional resource handling PCI: Perform reset_resource() and build fail list in sync PCI: Use res->parent to check if resource is assigned PCI: Add debug print when releasing resources before retry PCI: Indicate optional resource assignment failures PCI: Always have realloc_head in __assign_resources_sorted() PCI: Extend enable to check for any optional resource PCI: Add restore_dev_resource() PCI: Remove incorrect comment from pci_reassign_resource() PCI: Consolidate assignment loop next round preparation PCI: Rename retval to ret PCI: Use while loop and break instead of gotos PCI: Refactor pdev_sort_resources() & __dev_sort_resources() PCI: Converge return paths in __assign_resources_sorted() PCI: Add dev & res local variables to resource assignment funcs PCI: Add pci_resource_num() helper PCI: Check resource_size() separately PCI: Add pci_resource_is_iov() to identify IOV resources PCI: Use resource_set_{range,size}() helpers PCI: Use SZ_* instead of literals in setup-bus.c PCI: Fix old_size lower bound in calculate_iosize() too PCI: Allow relaxed bridge window tail sizing for optional resources PCI: Simplify size1 assignment logic PCI: Use min_align, not unrelated add_align, for size0 PCI: Remove add_align overwrite unrelated to size0 PCI: Use downstream bridges for distributing resources PCI: Cleanup dev->resource + resno to use pci_resource_n()
2025-03-27Merge branch 'pci/reset'Bjorn Helgaas
- Log debug messages about reset methods being used (Bjorn Helgaas) - Avoid reset when it has been disabled via sysfs (Nishanth Aravamudan) * pci/reset: PCI: Avoid reset when disabled via sysfs PCI: Log debug messages about reset method
2025-03-27Merge branch 'pci/pwrctrl'Bjorn Helgaas
- Create pwrctrl devices in pci_scan_device() to make it more symmetric with pci_pwrctrl_unregister() and make pwrctrl devices for PCI bridges possible (Manivannan Sadhasivam) - Unregister pwrctrl devices in pci_destroy_dev() so DOE, ASPM, etc. can still access devices after pci_stop_dev() (Manivannan Sadhasivam) - If there's a pwrctrl device for a PCI device, skip scanning it because the pwrctrl core will rescan the bus after the device is powered on (Manivannan Sadhasivam) - Add a pwrctrl driver for PCI slots based on voltage regulators described via devicetree (Manivannan Sadhasivam) * pci/pwrctrl: PCI/pwrctrl: Add pwrctrl driver for PCI slots dt-bindings: vendor-prefixes: Document the 'pciclass' prefix PCI/pwrctrl: Skip scanning for the device further if pwrctrl device is created PCI/pwrctrl: Move pci_pwrctrl_unregister() to pci_destroy_dev() PCI/pwrctrl: Move creation of pwrctrl devices to pci_scan_device()
2025-03-27Merge branch 'pci/pm'Bjorn Helgaas
- Allow PCI bridges to go to D3Hot on all non-x86 systems (Manivannan Sadhasivam) * pci/pm: PCI: Allow PCI bridges to go to D3Hot on all non-x86
2025-03-27Merge branch 'pci/hotplug'Bjorn Helgaas
- Drop shpchp module init/exit logging (Ilpo Järvinen) - Replace shpchp dbg() with ctrl_dbg() and remove unused dbg(), err(), info(), warn() wrappers (Ilpo Järvinen) - Drop 'shpchp_debug' module parameter in favor of standard dynamic debugging (Ilpo Järvinen) - Drop unused .get_power(), .set_power() function pointers (Guilherme Giacomo Simoes) - Drop superfluous pci_hotplug_slot_list (Lukas Wunner) - Drop superfluous try_module_get() calls (Lukas Wunner) - Drop superfluous NULL pointer checks (Lukas Wunner) - Pass struct hotplug_slot pointers directly to avoid backpointer dereferencing in has_*_file() (Lukas Wunner) - Inline pci_hp_{create,remove}_module_link() to reduce exported symbols (Lukas Wunner) - Disable hotplug interrupts in portdrv only when pciehp is not enabled to prevent issuing two hotplug commands too close together (Feng Tang) - Skip pciehp 'device replaced' check if the device has been removed to address a common deadlock when resuming after a device was removed during system sleep (Lukas Wunner) - Don't enable pciehp hotplug interupt when resuming in poll mode (Ilpo Järvinen) * pci/hotplug: PCI: pciehp: Don't enable HPIE when resuming in poll mode PCI: pciehp: Avoid unnecessary device replacement check PCI/portdrv: Only disable pciehp interrupts early when needed PCI: hotplug: Inline pci_hp_{create,remove}_module_link() PCI: hotplug: Avoid backpointer dereferencing in has_*_file() PCI: hotplug: Drop superfluous NULL pointer checks in has_*_file() PCI: hotplug: Drop superfluous try_module_get() calls PCI: hotplug: Drop superfluous pci_hotplug_slot_list PCI: cpcihp: Remove unused .get_power() and .set_power() PCI: shpchp: Remove 'shpchp_debug' module parameter PCI: shpchp: Remove unused logging wrappers PCI: shpchp: Change dbg() -> ctrl_dbg() PCI: shpchp: Remove logging from module init/exit functions
2025-03-27Merge branch 'pci/enumeration'Bjorn Helgaas
- Enable Configuration RRS SV early instead of during child bus scanning (Bjorn Helgaas) - Cache offset of Resizable BAR capability to avoid redundant searches for it (Bjorn Helgaas) - Fix reference leaks in pci_register_host_bridge() and pci_alloc_child_bus() (Ma Ke) - Drop put_device() in pci_register_host_bridge() left over from converting device_register() to device_add() (Dan Carpenter) * pci/enumeration: PCI: Remove stray put_device() in pci_register_host_bridge() PCI: Fix reference leak in pci_alloc_child_bus() PCI: Fix reference leak in pci_register_host_bridge() PCI: Cache offset of Resizable BAR capability PCI: Enable Configuration RRS SV early
2025-03-27Merge branch 'pci/doe'Bjorn Helgaas
- Rename DOE 'protocol' to 'feature' to follow spec terminology (Alistair Francis) - Expose supported DOE features via sysfs (Alistair Francis) - Allow DOE support to be enabled even if CXL isn't enabled (Alistair Francis) * pci/doe: PCI/DOE: Allow enabling DOE without CXL PCI/DOE: Expose DOE features via sysfs PCI/DOE: Rename Discovery Response Data Object Contents to type PCI/DOE: Rename DOE protocol to feature
2025-03-27Merge branch 'pci/devres'Bjorn Helgaas
- Enlarge the devres table[] to accommodate bridge windows, ROM, IOV BARs, etc (Philipp Stanner) - Validate BAR index in devres interfaces (Philipp Stanner) * pci/devres: PCI: Check BAR index for validity PCI: Fix wrong length of devres array
2025-03-27Merge branch 'pci/bwctrl'Bjorn Helgaas
- Add set_pcie_speed.sh to TEST_PROGS to fix issue when executing the set_pcie_cooling_state.sh test case (Yi Lai) - Fix the pcie_bwctrl_select_speed() return value in cases where a non-compliant device doesn't advertise valid supported speeds (Ilpo Järvinen) - Avoid a NULL pointer dereference when we run out of bus numbers to assign for a bridge secondary bus (Lukas Wunner) * pci/bwctrl: PCI/bwctrl: Fix NULL pointer dereference on bus number exhaustion PCI/bwctrl: Fix pcie_bwctrl_select_speed() return type selftests/pcie_bwctrl: Add 'set_pcie_speed.sh' to TEST_PROGS
2025-03-27Merge branch 'pci/aspm'Bjorn Helgaas
- Delay pcie_link_state deallocation to avoid dangling pointers that cause invalid references during hot-unplug (Daniel Stodden) * pci/aspm: PCI/ASPM: Fix link state exit during switch upstream function removal
2025-03-27Merge branch 'pci/aer'Bjorn Helgaas
- Implement local aer_printk() since AER is the only place that prints a message with level depending on the error severity (Ilpo Järvinen) * pci/aer: PCI/ERR: Handle TLP Log in Flit mode PCI: Track Flit Mode Status & print it with link status PCI/AER: Descope pci_printk() to aer_printk()
2025-03-27Merge branch 'pci/acs'Bjorn Helgaas
- Fix bugs in 'pci=config_acs=' kernel command line parameter (Tushar Dave) * pci/acs: PCI/ACS: Fix 'pci=config_acs=' parameter
2025-03-27PCI: layerscape: Fix arg_count to syscon_regmap_lookup_by_phandle_args()Ioana Ciornei
The arg_count parameter to syscon_regmap_lookup_by_phandle_args() represents the number of argument cells following the phandle. In this case, the number of arguments should be 1 instead of 2 since the dt property looks like this: fsl,pcie-scfg = <&scfg 0>; Without this fix, layerscape-pcie fails with the following message on LS1043A: OF: /soc/pcie@3500000: phandle scfg@1570000 needs 2, found 1 layerscape-pcie 3500000.pcie: No syscfg phandle specified layerscape-pcie 3500000.pcie: probe with driver layerscape-pcie failed with error -22 Link: https://lore.kernel.org/r/20250327151949.2765193-1-ioana.ciornei@nxp.com Fixes: 149fc35734e5 ("PCI: layerscape: Use syscon_regmap_lookup_by_phandle_args") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Roy Zang <Roy.Zang@nxp.com> Cc: stable@vger.kernel.org
2025-03-27Merge tag 'asm-generic-6.15-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic Pull asm-generic updates from Arnd Bergmann: "This is mainly set of cleanups of asm-generic/io.h, resolving problems with inconsistent semantics of ioread64/iowrite64 that were causing runtime and build issues. The "GENERIC_IOMAP" version that switches between inb()/outb() and readb()/writeb() style accessors is now only used on architectures that have PC-style ISA devices that are not memory mapped (x86, uml, m68k-q40 and powerpc-powernv), while alpha and parisc use a more complicated variant and everything else just maps the ioread interfaces to plan MMIO (readb/writeb etc). In addition there are two small changes from Raag Jadav to simplify the asm-generic/io.h indirect inclusions and from Jann Horn to fix a corner case with read_word_at_a_time" * tag 'asm-generic-6.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: rwonce: fix crash by removing READ_ONCE() for unaligned read rwonce: handle KCSAN like KASAN in read_word_at_a_time() m68k: coldfire: select PCI_IOMAP for PCI mips: export pci_iounmap() mips: fix PCI_IOBASE definition m68k/nommu: stop using GENERIC_IOMAP mips: drop GENERIC_IOMAP wrapper powerpc: asm/io.h: remove split ioread64/iowrite64 helpers parisc: stop using asm-generic/iomap.h sh: remove duplicate ioread/iowrite helpers alpha: stop using asm-generic/iomap.h io.h: drop unused headers drm/draw: include missing headers asm-generic/io.h: rework split ioread64/iowrite64 helpers
2025-03-27ima: limit the number of ToMToU integrity violationsMimi Zohar
Each time a file in policy, that is already opened for read, is opened for write, a Time-of-Measure-Time-of-Use (ToMToU) integrity violation audit message is emitted and a violation record is added to the IMA measurement list. This occurs even if a ToMToU violation has already been recorded. Limit the number of ToMToU integrity violations per file open for read. Note: The IMA_MAY_EMIT_TOMTOU atomic flag must be set from the reader side based on policy. This may result in a per file open for read ToMToU violation. Since IMA_MUST_MEASURE is only used for violations, rename the atomic IMA_MUST_MEASURE flag to IMA_MAY_EMIT_TOMTOU. Cc: stable@vger.kernel.org # applies cleanly up to linux-6.6 Tested-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Petr Vorel <pvorel@suse.cz> Tested-by: Petr Vorel <pvorel@suse.cz> Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com> Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
2025-03-27Merge tag 'soc-arm-6.15' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull SoC arm platform updates from Arnd Bergmann: "The at91 platform gains support for SAMA7D65, a new variant of the Cortex-A7 based SAMA7G5 with a graphics output. The i.MX, Renesas and davinci platforms each get one minor bugfix" * tag 'soc-arm-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: ARM: davinci: always enable CONFIG_ARCH_DAVINCI_DA850 ARM: imx: mark imx53_suspend_sz as unused ARM: at91: pm: Enable ULP0/ULP1 for SAMA7D65 ARM: at91: pm: Add Backup mode for SAMA7D65 ARM: at91: pm: add DT compatible support for sama7d65 ARM: at91: pm: fix at91_suspend_finish for ZQ calibration dt-bindings: ARM: at91: add Calao USB boards dt-bindings: ARM: at91: make separate entry for Olimex board ARM: at91: Add Support in SoC driver for SAMA7D65 dt-bindings: atmel-sysreg: Add SAMA7D65 Chip ID ARM: shmobile: rcar-gen2: Remove CMA reservation code
2025-03-27ima: limit the number of open-writers integrity violationsMimi Zohar
Each time a file in policy, that is already opened for write, is opened for read, an open-writers integrity violation audit message is emitted and a violation record is added to the IMA measurement list. This occurs even if an open-writers violation has already been recorded. Limit the number of open-writers integrity violations for an existing file open for write to one. After the existing file open for write closes (__fput), subsequent open-writers integrity violations may be emitted. Cc: stable@vger.kernel.org # applies cleanly up to linux-6.6 Tested-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Petr Vorel <pvorel@suse.cz> Tested-by: Petr Vorel <pvorel@suse.cz> Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com> Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
2025-03-27Merge tag 'soc-defconfig-6.15' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull SoC defconfig updates from Arnd Bergmann: "A small set of updates for the arm64 defconfig to enable more drivers, plus a bit for housekeeping on some of the arm32 defconfigs on particular SoC families" * tag 'soc-defconfig-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: arm: defconfig: drop RT_GROUP_SCHED=y from bcm2835/tegra/omap2plus arm64: defconfig: Enable USB retimer and redriver arm64: defconfig: Build NSS Clock Controller driver for IPQ9574 arm64: defconfig: Enable SPI NAND flashes arm64: defconfig: Enable Synopsys HDMI receiver arm64: defconfig: Enable Rockchip UFS host driver arm64: defconfig: enable Qualcomm IRIS & VIDEOCC_8550 as module arm64: defconfig: Enable HSR protocol driver arm64: defconfig: Enable gb_beagleplay arm64: defconfig: enable DRM_DISPLAY_CONNECTOR as a module arm64: defconfig: Enable Qualcomm QCM2290 GPU clock controller ARM: shmobile: defconfig: Supplement DTB with ATAG information
2025-03-27Merge tag 'soc-drivers-6.15-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull SoC driver updates from Arnd Bergmann: "These are the updates for SoC specific drivers and related subsystems: - Firmware driver updates for SCMI, FF-A and SMCCC firmware interfaces, adding support for additional firmware features including SoC identification and FF-A SRI callbacks as well as various bugfixes - Memory controller updates for Nvidia and Mediatek - Reset controller support for microchip sam9x7 and imx8qxp/imx8qm - New hardware support for multiple Mediatek, Renesas and Samsung Exynos chips - Minor updates on Zynq, Qualcomm, Amlogic, TI, Samsung, Nvidia and Apple chips There will be a follow up with a few more driver updates that are still causing build regressions at the moment" * tag 'soc-drivers-6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (97 commits) irqchip: Add support for Amlogic A4 and A5 SoCs dt-bindings: interrupt-controller: Add support for Amlogic A4 and A5 SoCs reset: imx: fix incorrect module device table dt-bindings: power: qcom,kpss-acc-v2: add qcom,msm8916-acc compatible bus: qcom-ssc-block-bus: Fix the error handling path of qcom_ssc_block_bus_probe() bus: qcom-ssc-block-bus: Remove some duplicated iounmap() calls soc: qcom: pd-mapper: Add support for SDM630/636 reset: imx: Add SCU reset driver for i.MX8QXP and i.MX8QM dt-bindings: firmware: imx: add property reset-controller dt-bindings: reset: atmel,at91sam9260-reset: add sam9x7 memory: mtk-smi: Add ostd setting for mt8192 dt-bindings: soc: samsung: exynos-usi: Drop unnecessary status from example firmware: tegra: bpmp: Fix typo in bpmp-abi.h soc/tegra: pmc: Use str_enable_disable-like helpers soc: samsung: include linux/array_size.h where needed firmware: arm_scmi: use ioread64() instead of ioread64_hi_lo() soc: mediatek: mtk-socinfo: Add extra entry for MT8395AV/ZA Genio 1200 soc: mediatek: mt8188-mmsys: Add support for DSC on VDO0 soc: mediatek: mmsys: Migrate all tables to MMSYS_ROUTE() macro soc: mediatek: mt8365-mmsys: Fix routing table masks and values ...
2025-03-27Documentation/rv: Add sched pages to the indicesGabriele Monaco
The pages Documentation/tools/rv/rv-mon-sched.rst and Documentation/trace/rv/monitor_sched.rst were introduced but not included in any index. Add them to the respective indices. Cc: Jonathan Corbet <corbet@lwn.net> Link: https://lore.kernel.org/20250327081240.46422-1-gmonaco@redhat.com Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Fixes: 03abeaa63c08 ("Documentation/rv: Add docs for the sched monitors") Signed-off-by: Gabriele Monaco <gmonaco@redhat.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2025-03-27Merge tag 'soc-dt-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds
Pull SoC devicetree updates from Arnd Bergmann: "There is new support for additional on-chip devices on Apple, Mediatek, Renesas, Rockchip, Samsung, Google, TI, ST, Nvidia and Amlogic devices. The Arm Morello reference platform gets a devicetree for booting in normal aarch64 mode. The hardware supports experimental CHERI support, which requires a modified kernel. The AMD (formerly Xilinx) Versal NET SoC gets added, this is a combined FPGA with Cortex-A78 CPUs in a SoC. Six new ST STM32MP2 SoC variants are added. Like the earlier STM32MP25, the MP211, MP213, MP215, MP231, MP233 and MP235 models are based on one or two Cortex-A35 cores but each feature a different set of I/O devices. Mediatek MT8370 is a minor variation of MT8390 with fewer CPU and GPU cores Apple T2 is the baseboard management controller on earlier Intel CPU based Macs, with 16 models now gaining initial support. All the above come with dts files for the reference boards. In addition, these boards are added for the SoCs that are already supported: - The Milk-V Jupiter board based on SpacemiT K1/M1 - NetCube Systems Kumquat board based on the 32-bit Allwinner V3s SoC - Three boards based on 32-bit stm32mp1 - 11 distinct board variants from Toradex and one from Variscite, all based on i.MX6 - Google Pixel Pro 6 phone based on gs101 (Tensor) - Three additional variants of the i.MX8MP based "Skov" board - A second variant of the i.MX95 EVK board - Two boards based on Renesas SoCs - Four boards based the Rockchip RK35xx series, plus the RK3588 'MNT Reform 2' laptop" * tag 'soc-dt-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (538 commits) arm64: dts: Add gpio_intc node for Amlogic A5 SoCs arm64: dts: Add gpio_intc node for Amlogic A4 SoCs arm64: dts: hi3660: Add property for fixing CPUIdle arm64: dts: rockchip: remove ethm0_clk0_25m_out from Sige5 gmac0 arm64: dts: marvell: Use preferred node names for "simple-bus" arm64: dts: marvell: Drop unused CP11X_TYPE define arm64: dts: marvell: Move arch timer and pmu nodes to top-level arm64: dts: rockchip: Fix PWM pinctrl names arm64: dts: rockchip: fix RK3576 SCMI clock IDs dt-bindings: clock: rk3576: add SCMI clocks arm64: dts: rockchip: Fix pcie reset gpio on Orange Pi 5 Max arm64: dts: amd/seattle: Drop undocumented "spi-controller" properties arm64: dts: amd/seattle: Fix bus, mmc, and ethernet node names arm64: dts: amd/seattle: Move and simplify fixed clocks arm64: dts: amd/seattle: Base Overdrive B1 on top of B0 version arm64: dts: rockchip: Enable HDMI audio output for ArmSoM Sige7 arm64: dts: rockchip: Enable onboard eMMC on Radxa E20C arm64: dts: rockchip: Add SDHCI controller for RK3528 arm64: dts: rockchip: Remove bluetooth node from rock-3a arm64: dts: rockchip: Move rk356x scmi SHMEM to reserved memory ...
2025-03-27tpm: Make chip->{status,cancel,req_canceled} optJarkko Sakkinen
tpm_ftpm_tee does not require chip->status, chip->cancel and chip->req_canceled. Make them optional. Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@opinsys.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27MAINTAINERS: TPM DEVICE DRIVER: add missing includesWangYuli
Add the missing headers to the "TPM DEVICE DRIVER" entry: 1. include/linux/tpm*.h 2. include/linux/vtpm_proxy.h [jarkko: wrote a new commit message. The original is in the linked post for reference.] Link: https://lore.kernel.org/linux-integrity/3E528EFF1AE81A17+20250311131440.1468875-1-wangyuli@uniontech.com/ Signed-off-by: WangYuli <wangyuli@uniontech.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27tpm: End any active auth session before shutdownJonathan McDowell
Lazy flushing of TPM auth sessions can interact badly with IMA + kexec, resulting in loaded session handles being leaked across the kexec and not cleaned up. Fix by ensuring any active auth session is ended before the TPM is told about the shutdown, matching what is done when suspending. Before: root@debian-qemu-efi:~# tpm2_getcap handles-loaded-session root@debian-qemu-efi:~# tpm2_getcap handles-saved-session root@debian-qemu-efi:~# kexec --load --kexec-file-syscall … root@debian-qemu-efi:~# systemctl kexec … root@debian-qemu-efi:~# tpm2_getcap handles-loaded-session - 0x2000000 root@debian-qemu-efi:~# tpm2_getcap handles-saved-session root@debian-qemu-efi:~# (repeat kexec steps) root@debian-qemu-efi:~# tpm2_getcap handles-loaded-session - 0x2000000 - 0x2000001 root@debian-qemu-efi:~# tpm2_getcap handles-saved-session root@debian-qemu-efi:~# After: root@debian-qemu-efi:~# tpm2_getcap handles-loaded-session root@debian-qemu-efi:~# tpm2_getcap handles-saved-session root@debian-qemu-efi:~# kexec --load --kexec-file-syscall … root@debian-qemu-efi:~# systemctl kexec … root@debian-qemu-efi:~# tpm2_getcap handles-loaded-session root@debian-qemu-efi:~# tpm2_getcap handles-saved-session root@debian-qemu-efi:~# Signed-off-by: Jonathan McDowell <noodles@meta.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27Documentation: tpm: Add documentation for the CRB FF-A interfaceStuart Yoder
Add documentation providing details of how the CRB driver interacts with ARM FF-A. [jarkko: Fine-tuned the commit message.] Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Stuart Yoder <stuart.yoder@arm.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27tpm_crb: Add support for the ARM FF-A start methodStuart Yoder
The TCG ACPI spec v1.4 defines a start method for the TPMs implemented with the ARM CRB over FF-A ABI. Add support for the FF-A start method, and use interfaces provided by the ffa_crb driver to interact with the FF-A based TPM. [jarkko: Fine-tuned the commit message.] Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Stuart Yoder <stuart.yoder@arm.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27ACPICA: Add start method for ARM FF-AStuart Yoder
Add TPM start method for ARM FF-A defined in the TCG ACPI specification v1.4. See: https://trustedcomputinggroup.org/wp-content/uploads/TCG-ACPI-Specification-Version-1.4-Revision-15_pub.pdf [jarkko: 1. Fine-tuned the commit message. 2. Added link to the TCG ACPI specification.] Link: https://github.com/acpica/acpica/pull/1000 Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Stuart Yoder <stuart.yoder@arm.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27tpm_crb: Clean-up and refactor check for idle supportStuart Yoder
Refactor TPM idle check to tpm_crb_has_idle(), and reduce paraentheses usage in start method checks [jarkko: Fine-tuned the commit message.] Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Stuart Yoder <stuart.yoder@arm.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27tpm_crb: ffa_tpm: Implement driver compliant to CRB over FF-AStuart Yoder
The ARM specification TPM Service CRB over FF-A specification defines the FF-A messages to interact with a CRB-based TPM implemented as an FF-A secure partition. See: https://developer.arm.com/documentation/den0138/latest/ This driver is probed when a TPM Secure Partition is discovered by the FF-A subsystem. It exposes APIs used by the TPM CRB driver to send notifications to the TPM. [jarkko: Fine-tuned the commit message.] Acked-by: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Stuart Yoder <stuart.yoder@arm.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27tpm/tpm_ftpm_tee: fix struct ftpm_tee_private documentationStefano Garzarella
The `state` member in `struct ftpm_tee_private` is in the documentation, but it has never been in the implementation since the commit 09e574831b27 ("tpm/tpm_ftpm_tee: A driver for firmware TPM running inside TEE") that introduced it. Remove it to have a match between documentation and implementation. Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27tpm, tpm_tis: Workaround failed command reception on Infineon devicesJonathan McDowell
Some Infineon devices have a issue where the status register will get stuck with a quick REQUEST_USE / COMMAND_READY sequence. This is not simply a matter of requiring a longer timeout; the work around is to retry the command submission. Add appropriate logic to do this in the send path. This is fixed in later firmware revisions, but those are not always available, and cannot generally be easily updated from outside a firmware environment. Testing has been performed with a simple repeated loop of doing a TPM2_CC_GET_CAPABILITY for TPM_CAP_PROP_MANUFACTURER using the Go code at: https://the.earth.li/~noodles/tpm-stuff/timeout-reproducer-simple.go It can take several hours to reproduce, and several million operations. Signed-off-by: Jonathan McDowell <noodles@meta.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27tpm, tpm_tis: Fix timeout handling when waiting for TPM statusJonathan McDowell
The change to only use interrupts to handle supported status changes introduced an issue when it is necessary to poll for the status. Rather than checking for the status after sleeping the code now sleeps after the check. This means a correct, but slower, status change on the part of the TPM can be missed, resulting in a spurious timeout error, especially on a more loaded system. Switch back to sleeping *then* checking. An up front check of the status has been done at the start of the function, so this does not cause an additional delay when the status is already what we're looking for. Cc: stable@vger.kernel.org # v6.4+ Fixes: e87fcf0dc2b4 ("tpm, tpm_tis: Only handle supported interrupts") Signed-off-by: Jonathan McDowell <noodles@meta.com> Reviewed-by: Michal Suchánek <msuchanek@suse.de> Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27tpm: Convert warn to dbg in tpm2_start_auth_session()Jonathan McDowell
TPM2 sessions have been flushed lazily since commit df745e25098dc ("tpm: Lazily flush the auth session"). If /dev/tpm{rm}0 is not accessed in-between two in-kernel calls, it is possible that a TPM2 session is re-started before the previous one has been completed. This causes a spurios warning in a legit run-time condition, which is also correctly addressed with a fast return path: [ 2.944047] tpm tpm0: auth session is active Address the issue by changing dev_warn_once() call to a dev_dbg_once() call. [jarkko: Rewrote the commit message, and instead of dropping converted to a debug message.] Signed-off-by: Jonathan McDowell <noodles@meta.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27tpm: Lazily flush auth session when getting random dataJonathan McDowell
Lazy flushing of TPM auth sessions was introduced to speed up IMA measurments into the TPM. Make use of it in tpm2_get_random as well, which has the added benefit of not needlessly cleaning up the session that IMA is using when there are no userspace accesses taking place. Command trace before for every call: hwrng (0x00000161): 14 (52965242 ns) hwrng (0x00000176): 48 (161612432 ns) hwrng (0x00000165): 10 (2410494 ns) hwrng (0x0000017B): 117 (70699883 ns) hwrng (0x0000017B): 117 (70959666 ns) hwrng (0x00000165): 10 (2756827 ns) After, with repeated calls showing no setup: hwrng (0x00000161): 14 (53044582 ns) hwrng (0x00000176): 48 (160491333 ns) hwrng (0x00000165): 10 (2408220 ns) hwrng (0x0000017B): 117 (70695037 ns) hwrng (0x0000017B): 117 (70994984 ns) hwrng (0x0000017B): 117 (70195388 ns) hwrng (0x0000017B): 117 (70973835 ns) Signed-off-by: Jonathan McDowell <noodles@meta.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27tpm: ftpm_tee: remove incorrect of_match_ptr annotationArnd Bergmann
Building with W=1 shows a warning about of_ftpm_tee_ids being unused when CONFIG_OF is disabled: drivers/char/tpm/tpm_ftpm_tee.c:356:34: error: unused variable 'of_ftpm_tee_ids' [-Werror,-Wunused-const-variable] Drop the unnecessary of_match_ptr(). Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Sumit Garg <sumit.garg@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27tpm: do not start chip while suspendedThadeu Lima de Souza Cascardo
Checking TPM_CHIP_FLAG_SUSPENDED after the call to tpm_find_get_ops() can lead to a spurious tpm_chip_start() call: [35985.503771] i2c i2c-1: Transfer while suspended [35985.503796] WARNING: CPU: 0 PID: 74 at drivers/i2c/i2c-core.h:56 __i2c_transfer+0xbe/0x810 [35985.503802] Modules linked in: [35985.503808] CPU: 0 UID: 0 PID: 74 Comm: hwrng Tainted: G W 6.13.0-next-20250203-00005-gfa0cb5642941 #19 9c3d7f78192f2d38e32010ac9c90fdc71109ef6f [35985.503814] Tainted: [W]=WARN [35985.503817] Hardware name: Google Morphius/Morphius, BIOS Google_Morphius.13434.858.0 10/26/2023 [35985.503819] RIP: 0010:__i2c_transfer+0xbe/0x810 [35985.503825] Code: 30 01 00 00 4c 89 f7 e8 40 fe d8 ff 48 8b 93 80 01 00 00 48 85 d2 75 03 49 8b 16 48 c7 c7 0a fb 7c a7 48 89 c6 e8 32 ad b0 fe <0f> 0b b8 94 ff ff ff e9 33 04 00 00 be 02 00 00 00 83 fd 02 0f 5 [35985.503828] RSP: 0018:ffffa106c0333d30 EFLAGS: 00010246 [35985.503833] RAX: 074ba64aa20f7000 RBX: ffff8aa4c1167120 RCX: 0000000000000000 [35985.503836] RDX: 0000000000000000 RSI: ffffffffa77ab0e4 RDI: 0000000000000001 [35985.503838] RBP: 0000000000000001 R08: 0000000000000001 R09: 0000000000000000 [35985.503841] R10: 0000000000000004 R11: 00000001000313d5 R12: ffff8aa4c10f1820 [35985.503843] R13: ffff8aa4c0e243c0 R14: ffff8aa4c1167250 R15: ffff8aa4c1167120 [35985.503846] FS: 0000000000000000(0000) GS:ffff8aa4eae00000(0000) knlGS:0000000000000000 [35985.503849] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [35985.503852] CR2: 00007fab0aaf1000 CR3: 0000000105328000 CR4: 00000000003506f0 [35985.503855] Call Trace: [35985.503859] <TASK> [35985.503863] ? __warn+0xd4/0x260 [35985.503868] ? __i2c_transfer+0xbe/0x810 [35985.503874] ? report_bug+0xf3/0x210 [35985.503882] ? handle_bug+0x63/0xb0 [35985.503887] ? exc_invalid_op+0x16/0x50 [35985.503892] ? asm_exc_invalid_op+0x16/0x20 [35985.503904] ? __i2c_transfer+0xbe/0x810 [35985.503913] tpm_cr50_i2c_transfer_message+0x24/0xf0 [35985.503920] tpm_cr50_i2c_read+0x8e/0x120 [35985.503928] tpm_cr50_request_locality+0x75/0x170 [35985.503935] tpm_chip_start+0x116/0x160 [35985.503942] tpm_try_get_ops+0x57/0x90 [35985.503948] tpm_find_get_ops+0x26/0xd0 [35985.503955] tpm_get_random+0x2d/0x80 Don't move forward with tpm_chip_start() inside tpm_try_get_ops(), unless TPM_CHIP_FLAG_SUSPENDED is not set. tpm_find_get_ops() will return NULL in such a failure case. Fixes: 9265fed6db60 ("tpm: Lock TPM chip in tpm_pm_suspend() first") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Cc: stable@vger.kernel.org Cc: Jerry Snitselaar <jsnitsel@redhat.com> Cc: Mike Seo <mikeseohyungjin@gmail.com> Cc: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2025-03-27ktest: Fix Test Failures Due to Missing LOG_FILE DirectoriesAyush Jain
Handle missing parent directories for LOG_FILE path to prevent test failures. If the parent directories don't exist, create them to ensure the tests proceed successfully. Cc: <warthog9@eaglescrag.net> Link: https://lore.kernel.org/20250307043854.2518539-1-Ayush.jain3@amd.com Signed-off-by: Ayush Jain <Ayush.jain3@amd.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2025-03-27tracing: probe-events: Add comments about entry data storing codeMasami Hiramatsu (Google)
Add comments about entry data storing code to __store_entry_arg() and traceprobe_get_entry_data_size(). These are a bit complicated because of building the entry data storing code and scanning it. This just add comments, no behavior change. Link: https://lore.kernel.org/all/174061715004.501424.333819546601401102.stgit@devnote2/ Reported-by: Steven Rostedt <rostedt@goodmis.org> Closes: https://lore.kernel.org/all/20250226102223.586d7119@gandalf.local.home/ Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2025-03-27selftests/ftrace: Add dynamic events argument limitation test caseMasami Hiramatsu (Google)
Add argument limitation test case for dynamic events. This is a boudary check for the maximum number of the probe event arguments. Link: https://lore.kernel.org/all/174055078295.4079315.14702008939511417359.stgit@mhiramat.tok.corp.google.com/ Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
2025-03-27selftests/ftrace: Add new syntax error testMasami Hiramatsu (Google)
Add BAD_TP_NAME syntax error message check. Link: https://lore.kernel.org/all/174055077485.4079315.3624012056141021755.stgit@mhiramat.tok.corp.google.com/ Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-30 13:46:54 +0000