| Age | Commit message (Collapse) | Author |
|---|
|
A randconfig caught repeated compiler warnings when CONFIG_IRQ_WORK=n
due to the definition of a non-inline static function in
<linux/irq_work.h>:
include/linux/irq_work.h +40 : warning: 'irq_work_needs_cpu' defined but not used
Make it inline to supress the warning. This is caused commit
00b42959106a ("irq_work: Don't stop the tick with pending works") merged
in v3.9-rc1.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The AcpiMmioSel bit is bit 1 in the AcpiMmioEn register, but the current
sp5100_tco driver is using bit 2.
See 2.3.3 Power Management (PM) Registers page 150 of the
AMD SB800-Series Southbridges Register Reference Guide [1].
AcpiMmioEn - RW – 8/16/32 bits - [PM_Reg: 24h]
Field Name Bits Default Description
AcpiMMioDecodeEn 0 0b Set to 1 to enable AcpiMMio space.
AcpiMMIoSel 1 0b Set AcpiMMio registers to be memory-mapped or IO-mapped space.
0: Memory-mapped space
1: I/O-mapped space
The sp5100_tco driver expects zero as a value of AcpiMmioSel (bit 1).
Fortunately, no problems were caused by this typo, because the default
value of the undocumented misused bit 2 seems to be zero.
However, the sp5100_tco driver should use the correct bitmask value.
[1] http://support.amd.com/us/Embedded_TechDocs/45482.pdf
Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
|
|
A problem was found on PC's with the SB700 chipset: The PC fails to
load BIOS after running the 3.8.x kernel until the power is completely
cut off. It occurs in all 3.8.x versions and the mainline version as of
2/4. The issue does not occur with the 3.7.x builds.
There are two methods for accessing the watchdog registers.
1. Re-programming a resource address obtained by allocate_resource()
to chipset.
2. Use the direct memory-mapped IO access.
The method 1 can be used by all the chipsets (SP5100, SB7x0, SB8x0 or
later). However, experience shows that only PC with the SB8x0 (or
later) chipsets can use the method 2.
This patch removes the method 1, because the critical problem was found.
That's why the watchdog timer was able to be used on SP5100 and SB7x0
chipsets until now.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1116835
Link: https://lkml.org/lkml/2013/2/14/271
Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
|
|
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
vfs_writev() updates the offset argument - but the code then passes the
offset to vfs_fsync_range(). Since offset now points to the offset after
what was just written, this is probably not what was intended
Introduced by face15025ffdf664de95e86ae831544154d26c9c "nfsd: use
vfs_fsync_range(), not O_SYNC, for stable writes".
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: stable@vger.kernel.org
Reviewed-by: Zach Brown <zab@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Fix typo on register address of slink3 controller where register
address is wrongly set as 0x7000d480 but it is 0x7000d800.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The 'CONFIG_' prefix is not implicit in IS_ENABLED().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
Pull KVM fix from Marcelo Tosatti:
"Fix compilation on PPC with !CONFIG_KVM"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
Revert "KVM: allow host header to be included even for !CONFIG_KVM"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of USB fixes that resolve issues that have been
reported against 3.9-rc3."
* tag 'usb-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (37 commits)
USB: ti_usb_3410_5052: fix use-after-free in TIOCMIWAIT
USB: ssu100: fix use-after-free in TIOCMIWAIT
USB: spcp8x5: fix use-after-free in TIOCMIWAIT
USB: quatech2: fix use-after-free in TIOCMIWAIT
USB: pl2303: fix use-after-free in TIOCMIWAIT
USB: oti6858: fix use-after-free in TIOCMIWAIT
USB: mos7840: fix use-after-free in TIOCMIWAIT
USB: mos7840: fix broken TIOCMIWAIT
USB: mct_u232: fix use-after-free in TIOCMIWAIT
USB: io_ti: fix use-after-free in TIOCMIWAIT
USB: io_edgeport: fix use-after-free in TIOCMIWAIT
USB: ftdi_sio: fix use-after-free in TIOCMIWAIT
USB: f81232: fix use-after-free in TIOCMIWAIT
USB: cypress_m8: fix use-after-free in TIOCMIWAIT
USB: ch341: fix use-after-free in TIOCMIWAIT
USB: ark3116: fix use-after-free in TIOCMIWAIT
USB: serial: add modem-status-change wait queue
USB: serial: fix interface refcounting
USB: io_ti: fix get_icount for two port adapters
USB: garmin_gps: fix memory leak on disconnect
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Mostly HD-audio and USB-audio regression fixes:
- Oops fix at unloading of snd-hda-codec-conexant module
- A few trivial regression fixes for Cirrus and Conexant HD-audio
codecs
- Relax the USB-audio descriptor parse errors as non-fatal
- Fix locking of HD-audio CA0132 DSP loader
- Fix the generic HD-audio parser for VIA codecs"
* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix DAC assignment for independent HP
ALSA: hda - Fix abuse of snd_hda_lock_devices() for DSP loader
ALSA: hda - Fix typo in checking IEC958 emphasis bit
ALSA: snd-usb: mixer: ignore -EINVAL in snd_usb_mixer_controls()
ALSA: snd-usb: mixer: propagate errors up the call chain
ALSA: usb: Parse UAC2 extension unit like for UAC1
ALSA: hda - Fix yet missing GPIO/EAPD setup in cirrus driver
ALSA: hda/cirrus - Fix the digital beep registration
ALSA: hda - Fix missing beep detach in patch_conexant.c
ALSA: documentation: Fix typo in Documentation/sound
|
|
Pull EDAC fixes from Borislav Petkov:
"A fix from Mauro to correct csrow size accounting in sysfs and a
sparse fix from Stephen Hemminger."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Merge mci.mem_is_per_rank with mci.csbased
amd64_edac: Correct DIMM sizes
EDAC: Make sysfs functions static
|
|
The LBA Range Type feature is optional in the NVMe specification,
so we should continue with adding namespaces for controllers that do
not implement this feature.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
|
Dave Jones found another /proc issue with his Trinity tool: thanks to
the namespace model, we can have multiple /proc dentries that point to
the same inode, aliasing directories in /proc/<pid>/net/ for example.
This ends up being a total disaster, because it acts like hardlinked
directories, and causes locking problems. We rely on the topological
sort of the inodes pointed to by dentries, and if we have aliased
directories, that odering becomes unreliable.
In short: don't do this. Multiple dentries with the same (directory)
inode is just a bad idea, and the namespace code should never have
exposed things this way. But we're kind of stuck with it.
This solves things by just always allocating a new inode during /proc
dentry lookup, instead of using "iget_locked()" to look up existing
inodes by superblock and number. That actually simplies the code a bit,
at the cost of potentially doing more inode [de]allocations.
That said, the inode lookup wasn't free either (and did a lot of locking
of inodes), so it is probably not that noticeable. We could easily keep
the old lookup model for non-directory entries, but rather than try to
be excessively clever this just implements the minimal and simplest
workaround for the problem.
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Analyzed-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit f445f11eb2cc265dd47da5b2e864df46cd6e5a82 as
it breaks PPC with CONFIG_KVM=n.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Create an entry for atmel i2c driver: i2c-at91.c
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
My old e-mail address is no longer working.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch adds the iSMT SMBus Controller DeviceIDs for the Intel Avoton SOC.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
NVIDIA's Tegra SoC allows read/write of controller register only
if controller clock is enabled. System hangs if read/write happens
to registers without enabling clock.
clk_prepare_enable() can be fail due to unknown reason and hence
adding check for return value of this function. If this function
success then only access register otherwise return to caller with
error.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Pull CIFS fixes from Steve French:
"Three small CIFS Fixes (the most important of the three fixes a recent
problem authenticating to Windows 8 using cifs rather than SMB2)"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs: ignore everything in SPNEGO blob after mechTypes
cifs: delay super block destruction until all cifsFileInfo objects are gone
cifs: map NT_STATUS_SHARING_VIOLATION to EBUSY instead of ETXTBSY
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix a number of regression and other bugs in ext4, most of which were
relatively obscure cornercases or races that were found using
regression tests."
* tag 'ext4_for_linue' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (21 commits)
ext4: fix data=journal fast mount/umount hang
ext4: fix ext4_evict_inode() racing against workqueue processing code
ext4: fix memory leakage in mext_check_coverage
ext4: use s_extent_max_zeroout_kb value as number of kb
ext4: use atomic64_t for the per-flexbg free_clusters count
jbd2: fix use after free in jbd2_journal_dirty_metadata()
ext4: reserve metadata block for every delayed write
ext4: update reserved space after the 'correction'
ext4: do not use yield()
ext4: remove unused variable in ext4_free_blocks()
ext4: fix WARN_ON from ext4_releasepage()
ext4: fix the wrong number of the allocated blocks in ext4_split_extent()
ext4: update extent status tree after an extent is zeroed out
ext4: fix wrong m_len value after unwritten extent conversion
ext4: add self-testing infrastructure to do a sanity check
ext4: avoid a potential overflow in ext4_es_can_be_merged()
ext4: invalidate extent status tree during extent migration
ext4: remove unnecessary wait for extent conversion in ext4_fallocate()
ext4: add warning to ext4_convert_unwritten_extents_endio
ext4: disable merging of uninitialized extents
...
|
|
EFI changes for v3.9-rc3,
* A new config option and efivars module parameter have been added to
allow the efivars pstore backend to be disabled as we're still seeing
issues on machines despite adding heuristics to workaround known bugs.
Distributions now have a way to disable EFI variable pstore code
completely - from Seth Forshee.
* A couple of efivars patches to workaround quirky implementations
of GetNextVariableName() which resulted in machines hanging and
sysfs files being created with garbage names.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Add missing __cpuinit annotation to apply_microcode_early().
Reported-by: Shaun Ruffell <sruffell@digium.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/20130320170310.GA23362@digium.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure waiting processes are woken on modem-status changes.
Currently processes are only woken on termios changes regardless of
whether the modem status has changed.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
When switching to tty ports, some lifetime assumptions were changed.
Specifically, close can now be called before the final tty reference is
dropped as part of hangup at device disconnect. Even with the ftdi
private-data refcounting this means that the port private data can be
freed while a process is sleeping on modem-status changes and thus
cannot be relied on to detect disconnects when woken up.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Also remove bogus test for private data pointer being NULL as it is
never assigned in the loop.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add modem-status-change wait queue to struct usb_serial_port that
subdrivers can use to implement TIOCMIWAIT.
Currently subdrivers use a private wait queue which may have been
released when waking up after device disconnected.
Note that we're adding a new wait queue rather than reusing the tty-port
one as we do not want to get woken up at hangup (yet).
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure the interface is not released before our serial device.
Note that drivers are still not allowed to access the interface in
any way that may interfere with another driver that may have gotten
bound to the same interface after disconnect returns.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add missing get_icount field to two-port driver.
The two-port driver was not updated when switching to the new icount
interface in commit 0bca1b913aff ("tty: Convert the USB drivers to the
new icount interface").
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove bogus disconnect test introduced by 95bef012e ("USB: more serial
drivers writing after disconnect") which prevented queued data from
being freed on disconnect.
The possible IO it was supposed to prevent is long gone.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unregister tty device in disconnect as is required by the USB stack.
By deferring unregistration to when the last tty reference is dropped,
the parent interface device can get unregistered before the child
resulting in broken hotplug events being generated when the tty is
finally closed:
KERNEL[2290.798128] remove /devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:3.1 (usb)
KERNEL[2290.804589] remove /devices/pci0000:00/0000:00:1d.7/usb2/2-1 (usb)
KERNEL[2294.554799] remove /2-1:3.1/tty/ttyACM0 (tty)
The driver must deal with tty callbacks after disconnect by checking the
disconnected flag. Specifically, further opens must be prevented and
this is already implemented.
Cc: stable <stable@vger.kernel.org>
Cc: Oliver Neukum <oneukum@suse.de>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
acm_probe() ignores errors in tty_port_register_device()
and leaves intfdata pointing to freed memory on alloc_fail7
error path. The patch fixes the both issues.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If pin_free is called on a pin already freed, mux_usecount is set to
UINT_MAX which is really a bad idea.
This will issue a warning, so that we can correct the code responsible
for the double free.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch fixes a minor bug (probably due to a typo) while checking
the SoC specific controls in mvebu_pinctrl_probe().
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We've had several reports of people attempting to mount Windows 8 shares
and getting failures with a return code of -EINVAL. The default sec=
mode changed recently to sec=ntlmssp. With that, we expect and parse a
SPNEGO blob from the server in the NEGOTIATE reply.
The current decode_negTokenInit function first parses all of the
mechTypes and then tries to parse the rest of the negTokenInit reply.
The parser however currently expects a mechListMIC or nothing to follow the
mechTypes, but Windows 8 puts a mechToken field there instead to carry
some info for the new NegoEx stuff.
In practice, we don't do anything with the fields after the mechTypes
anyway so I don't see any real benefit in continuing to parse them.
This patch just has the kernel ignore the fields after the mechTypes.
We'll probably need to reinstate some of this if we ever want to support
NegoEx.
Reported-by: Jason Burgess <jason@jacknife2.dns2go.com>
Reported-by: Yan Li <elliot.li.tech@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The imx fixes for 3.9, take 3:
- Add the lost dependency check for DEBUG_IMX_UART_PORT back
* tag 'imx-fixes-3.9-3' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The mxs fixes for 3.9, take 3:
- Fix the shifted framebuffer with X11 system
* tag 'mxs-fixes-3.9-3' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: video: mxs: Fix mxsfb misconfiguring VDCTRL0
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The generic parser should evaluate the availability of the independent
HP when specified. Otherwise a DAC without the direct connection to
the corresponding pin may be assigned for the HP, but the driver
doesn't check it at all. The problem was actually seen on some
machines with VT1708s or equivalent codec, where DAC0 is assigned to
HP although it can be connected only via aamix.
This patch adds the badness evaluation for the independent HP to make
it working properly.
Reported-by: Lydia Wang <LydiaWang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
