Age | Commit message (Collapse) | Author |
|
The data from the hardware should be little endian. Correct the
declaration.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The maximum packet number which a tx aggregation buffer could contain
is the tx_qlen.
tx_qlen = buffer size / (packet size + descriptor size).
If the tx buffer is empty and the queued packets are more than the
maximum value which is defined above, stop the tx queue. Wake the
tx queue if tx queue is stopped and the queued packets are less than
tx_qlen.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the code for sending the packet in the rtl8152_start_xmit().
Let rtl8152_start_xmit() to queue the packet only, and schedule a
tasklet to send the queued packets. This simplify the code and make
sure all the packet would be sent by the original order.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx/rx would access the memory which is out of the desired range.
Modify the method of checking the end of the memory to avoid it.
For r8152_tx_agg_fill(), the variable remain may become negative.
However, the declaration is unsigned, so the while loop wouldn't
break when reaching the end of the desied memory. Although to change
the declaration from unsigned to signed is enough to fix it, I also
modify the checking method for safe. Replace
remain = rx_buf_sz - sizeof(*tx_desc) -
(u32)((void *)tx_data - agg->head);
with
remain = rx_buf_sz - (int)(tx_agg_align(tx_data) - agg->head);
to make sure the variable remain is always positive. Then, the
overflow wouldn't happen.
For rx_bottom(), the rx_desc should not be used to calculate the
packet length before making sure the rx_desc is in the desired range.
Change the checking to two parts. First, check the descriptor is in
the memory. The other, using the descriptor to find out the packet
length and check if the packet is in the memory.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch exposes default_erl as a TPG attribute so that it may be
set TPG wide in demo-mode, but still allow the existing NodeACL
attribute to be overridden on a per initiator basis.
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Split up the various ALUA states into individual attributes to
make parsing easier and adhere to the one value per attribute
sysfs principle.
(nab: Convert strict_strtoul -> kstrtoul usage)
Signed-off-by: Hannes Reinecke <hare@suse.de>
|
|
Signed-off-by: Hannes Reinecke <hare@suse.de>
|
|
The supported ALUA states might be different for individual
devices, so store it in a separate field.
(nab: Remove unnecessary line continuation)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Rename ALUA_ACCESS_STATE_OPTMIZED to
ALUA_ACCESS_STATE_OPTIMIZED.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Disable interrupts and poll under high load
Signed-off-by: Jon Mason <jon.mason@intel.com>
|
|
Enable Snoop from Primary to Secondary side on BAR23 and BAR45 on all
TLPs. Previously, Snoop was only enabled from Secondary to Primary
side. This can have a performance improvement on some workloads.
Also, make the code more obvious about how the link is being enabled.
Signed-off-by: Jon Mason <jon.mason@intel.com>
|
|
Add a comment describing the necessary ordering of modifications to the
NTB Limit and Base registers.
Signed-off-by: Jon Mason <jon.mason@intel.com>
|
|
Remove duplicate defines in drivers/ntb/ntb_regs.h
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
|
|
dmaengine_get() causes the initialization of the per-cpu channel tables.
It needs to be called prior to dma_find_channel().
Initial version by Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
|
|
A WARN_ON is being hit in ntb_qp_link_work due to the NTB transport link
being down while the ntb qp link is still active. This is caused by the
transport link being brought down prior to the qp link worker thread
being terminated. To correct this, shutdown the qp's prior to bringing
the transport link down. Also, only call the qp worker thread if it is
in interrupt context, otherwise call the function directly.
Signed-off-by: Jon Mason <jon.mason@intel.com>
|
|
Current MSI-X enablement code assumes MSI-Xs were successfully
allocated in case less than requested vectors were available.
That assumption is wrong, since MSI-Xs should be enabled with
a repeated call to pci_enable_msix(). This update fixes this.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
|
|
The Xeon NTB-RP setup, the transparent side does not get a link up/down
interrupt. Since the presence of a NTB device on the transparent side
means that we have a NTB link up, we can work around the lack of an
interrupt by simply calling the link up function to notify the upper
layers.
Signed-off-by: Jon Mason <jon.mason@intel.com>
|
|
Modifications to the 14th bit of the B2BDOORBELL register will not be
mirrored to the remote system due to a hardware issue. To get around
the issue, shrink the number of available doorbell bits by 1. The max
number of doorbells was being used as a way to referencing the Link
Doorbell bit. Since this would no longer work, the driver must now
explicitly reference that bit.
This does not affect the xeon_errata_workaround case, as it is not using
the b2bdoorbell register.
Signed-off-by: Jon Mason <jon.mason@intel.com>
|
|
Since acpi_bus_get_device() returns plain int and not acpi_status,
ACPI_FAILURE() should not be used for checking its return value. Fix
that.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
When a codec is resumed, it keeps the power on while the resuming
phase via hda_keep_power_on(), then turns down via
snd_hda_power_down(). At that point, snd_hda_power_down() notifies
the power down to the controller, and this may confuse the refcount if
the codec was already powered up before the resume.
In the end result, the controller goes to runtime suspend even before
the codec is kicked off to the power save, and the communication
stalls happens.
The fix is to add the power-up notification together with
hda_keep_power_on(), and clears the flag appropriately.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The FLL must be placed into free-run mode before disabling
to allow it to entirely shut down.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
|
|
This regression has been introduced in
commit 4fe8590a921d0b2e36e542dbfa89a8c5993f5a3f
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Sep 4 18:25:22 2013 +0300
drm/i915: Use adjusted_mode appropriately when computing watermarks
I guess we should renable the enabled local variable into something a
notch more descriptive, but that's something for -next.
The effect on my i945gme netbook is pretty severe amounts of underruns
- usually the very first pixel gets used for the entire screeen.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This patch adds support for the built-in multitouch sensor in the Samsung
SUR40 touchscreen device, also known as Microsoft Surface 2.0 or Microsoft
Pixelsense. Support for raw video output from the sensor as well as the
accelerometer will be added in a later patch.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
You're looking at a casual headset patch,
for a specific hardware it will match,
and suddenly, the headset jack will work,
so please apply this simple quirk!
BugLink: https://bugs.launchpad.net/bugs/1253038
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Addresses
"[BUG] completely bonkers use of set_need_resched + VM_FAULT_NOPAGE".
In the first occurence it was used to try to be nice while releasing the
mmap_sem and retrying the fault to work around a locking inversion.
The second occurence was never used.
There has been some discussion whether we should change the locking order to
mmap_sem -> bo_reserve. This patch doesn't address that issue, and leaves
that locking order undefined. The solution that we release the mmap_sem if
tryreserve fails and wait for the buffer to become unreserved is something
we want in any case, and follows how the core vm system waits for pages
to be come unlocked while releasing the mmap_sem.
The code also outlines what needs to be changed if we want to establish the
locking order as mmap_sem -> bo::reserve.
One slight issue that remains with this code is that the fault handler might
be prone to starvation if another thread countinously reserves the buffer.
IMO that usage pattern is highly unlikely.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
If ttm_bo_move_memcpy was instructed to move a non-populated ttm to
io memory, it would first populate the ttm, then move the data and then
destroy the ttm. That's stupid. However, some drivers might have relied on
this to clear io memory from old stuff. So instead of a NOP, which would
be the most efficient, just clear the destination.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
|
|
We should not be using jump labels before they were initialized. Push back
the callback to until after jump label initialization.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
|
|
For all uapi headers, need use "_UAPI" prefix for its guard macro
(which will be stripped by "scripts/headers_installer.sh").
Also remove redundant files (bitsperlong.h, errno.h, fcntl.h, ioctl.h,
ioctls.h, ipcbuf.h, kvm_para.h, mman.h, poll.h, resource.h, siginfo.h,
statfs.h, and unistd.h) which are already in Kbuild.
Also be sure that all "#endif" only have one empty line above, and each
file has guard macro.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
|
|
This re-enables kprobes on AVR32 architecture.
Signed-off-by: Eirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
|
|
This patch fixes following error (for big kernels):
---8<---
arch/avr32/boot/u-boot/head.o: In function `no_tag_table':
(.init.text+0x44): relocation truncated to fit: R_AVR32_22H_PCREL against symbol `panic' defined in .text.unlikely section in kernel/built-in.o
arch/avr32/kernel/built-in.o: In function `bad_return':
(.ex.text+0x236): relocation truncated to fit: R_AVR32_22H_PCREL against symbol `panic' defined in .text.unlikely section in kernel/built-in.o
--->8---
It comes up when the kernel increases and 'panic()' is too far away to fit in
the +/- 2MiB range. Which in turn issues from the 21-bit displacement in
'br{cond4}' mnemonic which is one of the two ways to do jumps (rjmp has just
10-bit displacement and therefore a way smaller range). This fact was stated
before in 8d29b7b9f81d6b83d869ff054e6c189d6da73f1f.
One solution to solve this is to add a local storage for the symbol address
and just load the $pc with that value.
Signed-off-by: Andreas Bießmann <andreas@biessmann.de>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: stable@vger.kernel.org
|
|
Before the CRT was (fully) set up in kernel_entry (bss cleared before in
_start, but also not before jump to panic() in no_tag_table case).
This patch fixes this up to have a fully working CRT when branching to panic()
in no_tag_table.
Signed-off-by: Andreas Bießmann <andreas@biessmann.de>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: stable@vger.kernel.org
|
|
Drop percpu_ida.o from lib-y since it is also listed in obj-y
and it doesn't need to be listed in both places.
Move percpu-refcount.o from lib-y to obj-y to fix build errors
in target_core_mod:
ERROR: "percpu_ref_cancel_init" [drivers/target/target_core_mod.ko] undefined!
ERROR: "percpu_ref_kill_and_confirm" [drivers/target/target_core_mod.ko] undefined!
ERROR: "percpu_ref_init" [drivers/target/target_core_mod.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch changes iscsit_sequence_cmd() logic to no longer reject
non-immediate CmdSNs that exceed MaxCmdSN with a protocol error,
but instead silently ignore them.
This is done to correctly follow RFC-3720 Section 3.2.2.1:
For non-immediate commands, the CmdSN field can take any
value from ExpCmdSN to MaxCmdSN inclusive. The target MUST silently
ignore any non-immediate command outside of this range or non-
immediate duplicates within the range.
Reported-by: Santosh Kulkarni <santosh.kulkarni@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch converts a handful of iscsi_session statistics to type
atomic_long_t, instead of using iscsi_session->session_stats_lock
when incrementing these values.
More importantly, go ahead and drop the spinlock usage within
iscsit_setup_scsi_cmd(), iscsit_check_dataout_hdr(),
iscsit_send_datain(), and iscsit_build_rsp_pdu() fast-path code.
(Squash in Roland's target: Remove write-only stats fields and lock
from struct se_node_acl)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Fix static checker complaint that stream is not checked in
squashfs_decompressor_destroy().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reviewed-by: Minchan Kim <minchan@kernel.org>
|
|
This introduces an implementation of squashfs_readpage_block()
that directly decompresses into the page cache.
This uses the previously added page handler abstraction to push
down the necessary kmap_atomic/kunmap_atomic operations on the
page cache buffers into the decompressors. This enables
direct copying into the page cache without using the slow
kmap/kunmap calls.
The code detects when multiple threads are racing in
squashfs_readpage() to decompress the same block, and avoids
this regression by falling back to using an intermediate
buffer.
This patch enhances the performance of Squashfs significantly
when multiple processes are accessing the filesystem simultaneously
because it not only reduces memcopying, but it more importantly
eliminates the lock contention on the intermediate buffer.
Using single-thread decompression.
dd if=file1 of=/dev/null bs=4096 &
dd if=file2 of=/dev/null bs=4096 &
dd if=file3 of=/dev/null bs=4096 &
dd if=file4 of=/dev/null bs=4096
Before:
629145600 bytes (629 MB) copied, 45.8046 s, 13.7 MB/s
After:
629145600 bytes (629 MB) copied, 9.29414 s, 67.7 MB/s
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reviewed-by: Minchan Kim <minchan@kernel.org>
|
|
Restructure squashfs_readpage() splitting it into separate
functions for datablocks, fragments and sparse blocks.
Move the memcpying (from squashfs cache entry) implementation of
squashfs_readpage_block into file_cache.c
This allows different implementations to be supported.
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reviewed-by: Minchan Kim <minchan@kernel.org>
|
|
Further generalise the decompressors by adding a page handler
abstraction. This adds helpers to allow the decompressors
to access and process the output buffers in an implementation
independant manner.
This allows different types of output buffer to be passed
to the decompressors, with the implementation specific
aspects handled at decompression time, but without the
knowledge being held in the decompressor wrapper code.
This will allow the decompressors to handle Squashfs
cache buffers, and page cache pages.
This patch adds the abstraction and an implementation for
the caches.
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reviewed-by: Minchan Kim <minchan@kernel.org>
|
|
Add a multi-threaded decompression implementation which uses
percpu variables.
Using percpu variables has advantages and disadvantages over
implementations which do not use percpu variables.
Advantages:
* the nature of percpu variables ensures decompression is
load-balanced across the multiple cores.
* simplicity.
Disadvantages: it limits decompression to one thread per core.
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
|
|
Now squashfs have used for only one stream buffer for decompression
so it hurts parallel read performance so this patch supports
multiple decompressor to enhance performance parallel I/O.
Four 1G file dd read on KVM machine which has 2 CPU and 4G memory.
dd if=test/test1.dat of=/dev/null &
dd if=test/test2.dat of=/dev/null &
dd if=test/test3.dat of=/dev/null &
dd if=test/test4.dat of=/dev/null &
old : 1m39s -> new : 9s
* From v1
* Change comp_strm with decomp_strm - Phillip
* Change/add comments - Phillip
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
|