Age | Commit message (Collapse) | Author |
|
The sizes of the UFS PHY register regions are too small and does
specifically not cover all registers used by the Linux driver.
As Linux maps these regions as full pages this is currently not an issue
on Linux, but let's update the sizes to match the vendor driver.
Fixes: 3834a2e92229 ("arm64: dts: qcom: sm8150: Add ufs nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024091507.20342-2-johan+linaro@kernel.org
|
|
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024002356.28261-2-krzysztof.kozlowski@linaro.org
|
|
Add initial support for OnePlus 3 and 3T mobile phones. They are based
on the MSM8996 SoC.
Co-developed-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Harry Austen <hpausten@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221023204505.115141-5-hpausten@protonmail.com
|
|
Add compatible strings for the OnePlus 3 and 3T phones which utilise the
Qualcomm MSM8996 SoC.
Signed-off-by: Harry Austen <hpausten@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221023204505.115141-4-hpausten@protonmail.com
|
|
Add support for the sixth I2C interface on the MSM8996 SoC.
Signed-off-by: Harry Austen <hpausten@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221023204505.115141-3-hpausten@protonmail.com
|
|
Use one-based indexing throughout the file for BLSP devices to avoid
confusion. Most of the node names and labels are consistent already.
This patch just fixes a few pinconf node names to match the one-based
indexing used in the label names.
Signed-off-by: Harry Austen <hpausten@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221023204505.115141-2-hpausten@protonmail.com
|
|
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020225309.32116-2-krzysztof.kozlowski@linaro.org
|
|
Pin configuration has no "input-high" property, so drop it from node
described as Wifi host wake up pin.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020225309.32116-1-krzysztof.kozlowski@linaro.org
|
|
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Merge subnodes named 'pinconf' and 'pinmux' into one entry, add function
where missing (required by bindings for GPIOs) and reorganize overriding
pins by boards.
Split the SPI and UART configuration into separate nodes
1. SPI (MOSI, MISO, SCLK), SPI chip-select, SPI chip-select via GPIO,
2. UART per each pin: TX, RX and optional CTS/RTS.
This allows each board to customize them easily without adding any new
nodes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020225135.31750-4-krzysztof.kozlowski@linaro.org
|
|
SPI CS at bootup on trogdor"
This reverts commit e440e30e26dd6b0424002ad0ddcbbcea783efd85 because it
is not a reliable way of fixing SPI CS glitch and it depends on specific
Linux kernel pin controller driver behavior.
This behavior of kernel driver was changed in commit b991f8c3622c
("pinctrl: core: Handling pinmux and pinconf separately") thus
effectively the DTS fix stopped being effective.
Proper solution for the glitching SPI chip select must be implemented in
the drivers, not via ordering of entries in DTS, and is already
introduced in commit d21f4b7ffc22 ("pinctrl: qcom: Avoid glitching lines
when we first mux to output").
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020225135.31750-3-krzysztof.kozlowski@linaro.org
|
|
The Trogdor Homestar DTSI adds additional GPIO52 pin to secondary I2S pins
("sec_mi2s_active") and configures it to "mi2s_1" function.
The Trogdor DTSI (which is included by Homestar) configures drive
strength and bias for all "sec_mi2s_active" pins, thus the intention was
to apply this configuration also to GPIO52 on Homestar.
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Fixes: be0416a3f917 ("arm64: dts: qcom: Add sc7180-trogdor-homestar")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020225135.31750-2-krzysztof.kozlowski@linaro.org
|
|
Use SM6350 as fallback for GPI DMA, to indicate devices are compatible
and that drivers can bind with only one compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221018230352.1238479-6-krzysztof.kozlowski@linaro.org
|
|
Use SM6350 as fallback for GPI DMA, to indicate devices are compatible
and that drivers can bind with only one compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221018230352.1238479-5-krzysztof.kozlowski@linaro.org
|
|
Use SM6350 as fallback for GPI DMA, to indicate devices are compatible
and that drivers can bind with only one compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221018230352.1238479-4-krzysztof.kozlowski@linaro.org
|
|
Enable the Round Robin ADC for the OnePlus 5/5T.
Signed-off-by: Jami Kettunen <jami.kettunen@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016180330.1912214-6-caleb.connolly@linaro.org
|
|
Enable the PMI8998 RRADC.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016180330.1912214-5-caleb.connolly@linaro.org
|
|
Enable the Round Robin ADC for the db845c.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016180330.1912214-4-caleb.connolly@linaro.org
|
|
Enable the RRADC for the OnePlus 6.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016180330.1912214-3-caleb.connolly@linaro.org
|
|
Add a DT node for the Round Robin ADC found in the PMI8998 PMIC.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016180330.1912214-2-caleb.connolly@linaro.org
|
|
New device support - Samsung S9 (SM-G9600) phone
What works:
- simple framebuffer
- storage (both main and sdcard)
- ramoops
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221012185411.1282838-3-dsankouski@gmail.com
|
|
Add samsung,starqltechn board (Samsung Galaxy S9) binding.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221012185411.1282838-2-dsankouski@gmail.com
|
|
DT schema expects LPASS pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220927153429.55365-5-krzysztof.kozlowski@linaro.org
|
|
The pull-down property is actually bias-pull-down.
Fixes: 3160c1b894d9 ("arm64: dts: qcom: sm8250: add lpass lpi pin controller node")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220927153429.55365-4-krzysztof.kozlowski@linaro.org
|
|
DT schema expects LPASS pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220927153429.55365-3-krzysztof.kozlowski@linaro.org
|
|
The LPASS pin-controller is not a clock provider:
qcom/sc7280-herobrine-herobrine-r1.dtb: pinctrl@33c0000: '#clock-cells' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220927153429.55365-2-krzysztof.kozlowski@linaro.org
|
|
In addition to PMIC-specific (pm6125) thermistors downstream extends
this set with the rf-pa0/rf-pa1, quiet, camera-flash and UFS/eMMC
thermistors in sm6125 (trinket) board and seine-specific DT files. All
thermistors report sensible temperature readings in userspace.
The sensors are also added to their respective Thermal Monitor node,
with thermal zones to match where applicable: emmc-ufs and camera-flash
are not available on the TM5 block, hence cannot be configured with a
tripping point and will not have a thermal zone.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220926190148.283805-6-marijn.suijten@somainline.org
|
|
The Sony Xperia Seine board uses the PM6125; include it and configure
the PON buttons that provide the power and volume-up key.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220926190148.283805-5-marijn.suijten@somainline.org
|
|
This PMIC is commonly used on boards with an SM6125 SoC and looks very
similar in layout to the PM6150.
Downstream declares more nodes to be available, but these have been
omitted from this patch: the pwm/lpg block is unused on my reference
device making it impossible to test/validate, and the spmi-clkdiv does
not have a single device-tree binding using this driver yet, hence
inclusion is better postponed until ie. audio which uses these clocks is
brought up.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220926190148.283805-4-marijn.suijten@somainline.org
|
|
The register address in the node name is shadowing vph_pwr@83, whereas
the ADC5_VCOIN register resolves to 0x85. Fix this copy-paste
discrepancy.
Fixes: 4bf097540506 ("arm64: dts: qcom: pm660: Add VADC and temp alarm nodes")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220926190148.283805-3-marijn.suijten@somainline.org
|
|
Document support for the pm6125, typically paired with the sm6125 SoC.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220926190148.283805-2-marijn.suijten@somainline.org
|
|
Change HDMI PHY node name from custom 'hdmi-phy' to the generic 'phy'.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220924094347.178666-3-dmitry.baryshkov@linaro.org
|
|
Document Google Cheza board compatibles recently added.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220918095430.18068-1-krzysztof.kozlowski@linaro.org
|
|
Add initial support for OnePlus Nord N100, based on SM4250. Currently
working:
- boots
- usb
- built-in flash storage (UFS)
- SD card reader
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220919180618.1840194-9-iskren.chernev@gmail.com
|
|
The SM4250 is a downclocked version of the SM6115.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220919180618.1840194-8-iskren.chernev@gmail.com
|
|
Add support for Qualcomm SM6115 SoC. This includes:
- GCC
- Pinctrl
- RPM (CC+PD)
- USB
- MMC
- UFS
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220919180618.1840194-7-iskren.chernev@gmail.com
|
|
oneplus,billie2 (OnePlus Nord N100) is based on QualComm Snapdragon
SM4250 SoC.
Add support for the same in dt-bindings.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220919180618.1840194-4-iskren.chernev@gmail.com
|
|
Add the TCSR node which is needed for PCIe configuration.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024125843.25261-1-johan+linaro@kernel.org
|
|
Both a2015 devices use motor drivers controlled with PWM signal.
A5 additionally has a fixed regulator that powers the driver and is
controlled by enable signal. A3 routes that enable signal to the
motor driver itself.
To simplify the description, add the motor to the common dtsi and
assume a regulator is used for both.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
[Rename the nodes to be reusable in msm8916-sansung-e2015]
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020115255.2026-1-linmengbo0689@protonmail.com
|
|
The documented yaml compat string for the apq8016 is
"qcom,apq8016-lpass-cpu" not "qcom,lpass-cpu-apq8016". Looking at the other
lpass compat strings the general form is "qcom,socnum-lpass-cpu".
We need to fix both the driver and dts to match.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220628120435.3044939-3-bryan.odonoghue@linaro.org
|
|
Add the MDSS, MDP and DSI nodes that are found on msm8953 SoC.
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016161554.673006-4-luca@z3ntu.xyz
|
|
Add the nodes describing the iommu and its context banks that are found
on msm8953 SoCs.
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016161554.673006-3-luca@z3ntu.xyz
|
|
Some devices have been using hsuart0 as an alias for the bluetooth UART,
rename this to serial1
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016172944.1892206-4-kc@postmarketos.org
|
|
Add serial1 alias, firmware name and use 4 pin UART pinmux.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016172944.1892206-3-kc@postmarketos.org
|
|
The 4-pin configuration for UART6 is used for all or almost all SDM845
devices with built in Bluetooth. Move the pinmux configuration to
sdm845.dtsi in preparation to be removed from individual devices in
future patches.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016172944.1892206-2-kc@postmarketos.org
|
|
The bindings require a SoC-specific compatible to be used next to
qcom,cpufreq-epss. Add it to make dtbs_check happy.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221016090035.565350-2-luca@z3ntu.xyz
|
|
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221013210612.95994-3-krzysztof.kozlowski@linaro.org
|
|
There is no "normal" function, so use "gpio" for backlight button pin
configuration.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221013210612.95994-2-krzysztof.kozlowski@linaro.org
|
|
Qualcomm pinctrl bindings and drivers expect gpio-ranges property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221013210612.95994-1-krzysztof.kozlowski@linaro.org
|
|
This ufs_variant node seems to be a remnant from downstream devicetree.
As it doesn't seem to be used by anything upstream, remove it from the
dtsi.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221012215613.32054-1-luca@z3ntu.xyz
|
|
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix. All
nodes for GPIOs must also define the function property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221011190231.76784-3-krzysztof.kozlowski@linaro.org
|