summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2022-05-17media: i2c: Remove per-mode frequencies from ov7251Daniel Scally
Each of the defined modes in the ov7251 driver uses the same link frequency and pixel rate; just drop those members of the modes and set the controls to read only during initialisation. Add a new table defining the supported pixel rates to substitue for the values hardcoded in the modes. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Provide ov7251_check_hwcfg()Daniel Scally
Move the endpoint checking from .probe() to a dedicated function, and additionally check that the firmware provided link frequencies are a match for those supported by the driver. Store the index to the matching link frequency so it can be easily identified later. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Add acpi support to ov7251Daniel Scally
Add support for enumeration through ACPI to the ov7251 driver Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: ipu3-cio2: Add support for V4L2_PIX_FMT_IPU3_Y10Daniel Scally
We have platforms where a camera sensor transmits Y10 data to the CIO2 device - add support for that (packed) format to the ipu3-cio2 driver. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: uapi: Add IPU3 packed Y10 formatDaniel Scally
Some platforms with an Intel IPU3 have an IR sensor producing 10 bit greyscale format data that is transmitted over a CSI-2 bus to a CIO2 device - this packs the data into 32 bytes per 25 pixels. Add an entry to the uAPI header defining that format. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: ov5645: Remove unneeded of_match_ptr macroMoses Christopher Bollavarapu
of_match_ptr isn't required as CONFIG_OF is already a dependency in Kconfig Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: ov8856: apply digital gain by setting global gain control registerBingbu Cao
MWB gain register are used to set gain for each mwb channel mannually. However, it will involve some artifacts if gain cannot be applied to each channel synchronously. Enable global gain control to set digital global gain instead of setting AWB gain separately to fix this issue. Signed-off-by: Bingbu Cao <bingbu.cao@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: ov5648: fix wrong pointer passed to IS_ERR() and PTR_ERR()Yang Yingliang
IS_ERR() and PTR_ERR() use wrong pointer, it should be sensor->dovdd, fix it. Fixes: e43ccb0a045f ("media: i2c: Add support for the OV5648 image sensor") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: Documentation: mc: Add media_device_{init,cleanup}Sakari Ailus
Document that drivers must first initialise a media device before registering it, and clean up once the media device is unregistered. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: Add MIPI CSI-2 28 bits per pixel raw data typeSakari Ailus
Add CSI-2 data type for 28 bits per pixel data. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: ov2640: Depend on V4L2_ASYNCMike Pagano
Add V4L2_ASYNC as a dependency to match other drivers and prevent failures when compile testing. Fixes: ff3cc65cadb5 ("media: v4l: async, fwnode: Improve module organisation") Signed-off-by: Mike Pagano <mpagano@gentoo.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: video-i2c: Use GENMASK for masking bitsMoses Christopher Bollavarapu
Replace 0x0380 with GENMASK(9, 7) to obtain 0b0000_0011_1000_0000 Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: video-i2c: Replace constants with proper namesMoses Christopher Bollavarapu
Acc to MLX90640 datasheet: - 0x0400 represents the start of RAM address - 0x2400 represents the start of EEPROM address Reference: https://www.melexis.com/-/media/files/documents\ /datasheets/mlx90640-datasheet-melexis.pdf Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: video-i2c: Move defines to the top of the fileMoses Christopher Bollavarapu
Currently, the defines in this driver are after some structs and functions, it makes more sense to move them up to the top of the file, so that the constants can be named together with other defines. Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: exynos4-is: Fix compile warningKwanghoon Son
Declare static on function 'fimc_isp_video_device_unregister'. When VIDEO_EXYNOS4_ISP_DMA_CAPTURE=n, compiler warns about warning: no previous prototype for function [-Wmissing-prototypes] Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Kwanghoon Son <k.son@samsung.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: adv7180: Add support for the test patternsFabio Estevam
ADV7180 has a built-in mechanism to generate some video patterns, which is very useful for debug/bring-up activities. Add support for it. The test_pattern parameter can be one of the following values: 0: "Single color" 1: "Color bars" 2: "Luma ramp" 3: "Boundary box" 4: "Disable" Tested on a imx6q board with an ADV7280. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: ti: cal: use frame desc to get vc and dtTomi Valkeinen
Use get_frame_desc() to get the frame desc from the connected source, and use the provided virtual channel and datatype instead of hardcoded ones. get_frame_desc() can contain multiple streams, but as we don't support multiple streams yet, we will just always use the first stream. If the source doesn't support get_frame_desc(), fall back to the previous method of always capturing virtual channel 0 and any datatype. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: Add CSI-2 bus configuration to frame descriptorsSakari Ailus
Add CSI-2 bus specific configuration to the frame descriptors. This allows obtaining the virtual channel and data type information for each stream the transmitter is sending. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: Add bus type to frame descriptorsSakari Ailus
Add the media bus type to the frame descriptor. CSI-2 specific information will be added in next patch to the frame descriptor. - Make the bus type a named enum Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: dt-bindings: media: video-interfaces: Add new bus-typeXin Ji
No properly bus-type for DPI video bus, add bus-type 7 for it. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Xin Ji <xji@analogixsemi.com> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: media/v4l2-core: Add enum V4L2_FWNODE_BUS_TYPE_DPIXin Ji
As V4L2_FWNODE_BUS_TYPE_PARALLEL is not used for DPI interface, this patch add V4L2_FWNODE_BUS_TYPE_DPI for video DPI interface. Signed-off-by: Xin Ji <xji@analogixsemi.com> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: ov7670: remove ov7670_power_off from ov7670_removeDongliang Mu
In ov7670_probe, it always invokes ov7670_power_off() no matter the execution is successful or failed. So we cannot invoke it agiain in ov7670_remove(). Fix this by removing ov7670_power_off from ov7670_remove. Fixes: 030f9f682e66 ("media: ov7670: control clock along with power") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: dw9807-vcm: Add "dongwoon,dw9807" compatible stringSakari Ailus
There is firmware out there that uses "dongwoon,dw9807" compatible string that never made it to upstream as-is. Add it to the driver to make it load on such systems. The chip also has an EEPROM part which is AT24 compatible (for reading purposes) on a separate I²C address. Adding possible support for this in the future is not affected by this change. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: dt-bindings: Convert Dongwoon dw9807-vcm bindings to json-schemaSakari Ailus
Convert the old text based dw9807-vcm chip DT bindings to json-schema. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: imx412: Add bulk regulator supportBryan O'Donoghue
Depending on the platform we may need to enable and disable three separate regulators for the imx412. - DOVDD Digital I/O power - AVDD Analog power - DVDD Digital core power The addition of these regulators shouldn't affect existing users using fixed-on/firmware-controlled regulators. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: dt-bindings: imx412: Add regulator descriptionsBryan O'Donoghue
The imx412 like many I2C camera sensors has three voltage rails which depending on platform may be necessary to switch power onto directly. Add in as optional rails so as not to break anything for existing users. Cc: Rob Herring <robh+dt@kernel.org> Cc: Krzysztof Kozlowski <krzk+dt@kernel.org> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: imx412: Fix power_off orderingBryan O'Donoghue
The enable path does - gpio - clock The disable path does - gpio - clock Fix the order on the power-off path so that power-off and power-on have the same ordering for clock and gpio. Fixes: 9214e86c0cc1 ("media: i2c: Add imx412 camera sensor driver") Cc: stable@vger.kernel.org Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: imx412: Fix reset GPIO polarityBryan O'Donoghue
The imx412/imx577 sensor has a reset line that is active low not active high. Currently the logic for this is inverted. The right way to define the reset line is to declare it active low in the DTS and invert the logic currently contained in the driver. The DTS should represent the hardware does i.e. reset is active low. So: + reset-gpios = <&tlmm 78 GPIO_ACTIVE_LOW>; not: - reset-gpios = <&tlmm 78 GPIO_ACTIVE_HIGH>; I was a bit reticent about changing this logic since I thought it might negatively impact @intel.com users. Googling a bit though I believe this sensor is used on "Keem Bay" which is clearly a DTS based system and is not upstream yet. Fixes: 9214e86c0cc1 ("media: i2c: Add imx412 camera sensor driver") Cc: stable@vger.kernel.org Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: h264: Avoid wrapping long_term_frame_idxNicolas Dufresne
For long term references, frame_num is set to long_term_frame_idx which does not require wrapping. This is fixed by observation, no directly related issue have been found yet. Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com> Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: v4l2-mem2mem: Trace on implicit un-holdNicolas Dufresne
If the timestamp of the src buffer differs from the timestamp of a held dst buffer, the held buffer is implicitly removed and marked as done. Add a trace to help debugging if someone hits that case. Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com> Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: doc: Document dual use of H.264 pic_num/frame_numNicolas Dufresne
These two fields need documentation as they have dual meaning. It is also confusing since pic_num is a derived value from frame_num, so this should help application developers. If we ever need to make a V2 of this API, I would suggest to remove pic_num entirely. Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: add h264 decoder driver for mt8186Yunfei Dong
Add h264 decode driver to support mt8186. For the architecture is single core, need to add new interface to decode. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: Support MT8186Yunfei Dong
Adds MT8186's compatible "mediatek,mt8186-vcodec-dec". Adds MT8186's device private data mtk_vdec_single_core_pdata. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: dt-bindings: media: mediatek: vcodec: Adds decoder dt-bindings for mt8186Yunfei Dong
Adds decoder dt-bindings for mt8186. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: prevent kernel crash when rmmod mtk-vcodec-dec.koYunfei Dong
If the driver support subdev mode, the parameter "dev->pm.dev" will be NULL in mtk_vcodec_dec_remove. Kernel will crash when try to rmmod mtk-vcodec-dec.ko. [ 4380.702726] pc : do_raw_spin_trylock+0x4/0x80 [ 4380.707075] lr : _raw_spin_lock_irq+0x90/0x14c [ 4380.711509] sp : ffff80000819bc10 [ 4380.714811] x29: ffff80000819bc10 x28: ffff3600c03e4000 x27: 0000000000000000 [ 4380.721934] x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000 [ 4380.729057] x23: ffff3600c0f34930 x22: ffffd5e923549000 x21: 0000000000000220 [ 4380.736179] x20: 0000000000000208 x19: ffffd5e9213e8ebc x18: 0000000000000020 [ 4380.743298] x17: 0000002000000000 x16: ffffd5e9213e8e90 x15: 696c346f65646976 [ 4380.750420] x14: 0000000000000000 x13: 0000000000000001 x12: 0000000000000040 [ 4380.757542] x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 [ 4380.764664] x8 : 0000000000000000 x7 : ffff3600c7273ae8 x6 : ffffd5e9213e8ebc [ 4380.771786] x5 : 0000000000000000 x4 : 0000000000000001 x3 : 0000000000000000 [ 4380.778908] x2 : 0000000000000000 x1 : ffff3600c03e4000 x0 : 0000000000000208 [ 4380.786031] Call trace: [ 4380.788465] do_raw_spin_trylock+0x4/0x80 [ 4380.792462] __pm_runtime_disable+0x2c/0x1b0 [ 4380.796723] mtk_vcodec_dec_remove+0x5c/0xa0 [mtk_vcodec_dec] [ 4380.802466] platform_remove+0x2c/0x60 [ 4380.806204] __device_release_driver+0x194/0x250 [ 4380.810810] driver_detach+0xc8/0x15c [ 4380.814462] bus_remove_driver+0x5c/0xb0 [ 4380.818375] driver_unregister+0x34/0x64 [ 4380.822288] platform_driver_unregister+0x18/0x24 [ 4380.826979] mtk_vcodec_dec_driver_exit+0x1c/0x888 [mtk_vcodec_dec] [ 4380.833240] __arm64_sys_delete_module+0x190/0x224 [ 4380.838020] invoke_syscall+0x48/0x114 [ 4380.841760] el0_svc_common.constprop.0+0x60/0x11c [ 4380.846540] do_el0_svc+0x28/0x90 [ 4380.849844] el0_svc+0x4c/0x100 [ 4380.852975] el0t_64_sync_handler+0xec/0xf0 [ 4380.857148] el0t_64_sync+0x190/0x194 [ 4380.860801] Code: 94431515 17ffffca d503201f d503245f (b9400004) Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: support stateless VP9 decodingYunfei Dong
Add support for VP9 decoding using the stateless API, as supported by MT8192. And the drivers is lat and core architecture. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Signed-off-by: George Sun <george.sun@mediatek.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: support stateless VP8 decodingYunfei Dong
Add support for VP8 decoding using the stateless API, as supported by MT8192. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: support stateless H.264 decoding for mt8192Yunfei Dong
Adds h264 lat and core architecture driver for mt8192, and the decode mode is frame based for stateless decoder. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: Extract H264 common codeYunfei Dong
Mt8192 can use some of common code with mt8183. Moves them to a new file in order to reuse. [hverkuil: replaced memcpy_toio by memcpy, was left over from a prev version] Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: record capture queue format typeYunfei Dong
The capture queue format type may be differ depending on platform: for stateless decoder drivers, we need to calculate the capture buffer size according to the capture queue format type in SCP. As a preparation for introducing drivers for stateless decoding, save the current capture queue type on a per vcodec context basis. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: Fix v4l2-compliance failYunfei Dong
Need to use default pic info when get pic info fail. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Reviewed-by: Steve Cho <stevecho@chromium.org> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: disable vp8 4K capabilityYunfei Dong
For vp8 not support 4K, need to disable it. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: Add format to support MT21CYunfei Dong
Needs to use mediatek compressed mode for mt8192 decoder. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: Getting supported decoder format typesYunfei Dong
Getting supported output and capture queue format types according to decoder capability. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: Refactor supported vdec formats and framesizesYunfei Dong
Supported output and capture format types for mt8192 are different with mt8183. Redefine parameters to store them. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: Refactor get and put capture buffer flowYunfei Dong
For lat and core decode in parallel, need to get capture buffer when core start to decode and put capture buffer to display list when core decode done. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: set each plane bytesused in buf prepareYunfei Dong
call vb2_set_plane_payload to set each plane bytesused in buf prepare, need not to set independently for stateless and statefull architectures. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: Read max resolution from dec_capabilityYunfei Dong
Supported max resolution for different platforms are not the same: 2K or 4K, getting it according to dec_capability. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Reviewed-by: Tzung-Bi Shih<tzungbi@google.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: get capture queue buffer size from scpYunfei Dong
Different capture buffer format has different buffer size, need to get real buffer size according to buffer type from scp. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-13media: mediatek: vcodec: Using firmware type to separate different firmware ↵Yunfei Dong
architecture MT8173 platform use vpu firmware, mt8183/mt8192 will use scp firmware instead, using chip name is not reasonable to separate different firmware architecture. Using firmware type is much better. Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Reviewed-by: Tzung-Bi Shih<tzungbi@google.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-01 20:22:10 +0000