| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator documentation fixes from Mark Brown:
"All the fixes people have found for the regulator API have been
documentation fixes, avoiding warnings while building the kerneldoc,
fixing some errors in one of the DT bindings documents and fixing some
typos in the header"
* tag 'regulator-v3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fix kernel-doc warnings in header files
regulator: Proofread documentation
regulator: tps65090: Fix tps65090 typos in example
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.17-rc3" from Tony Lindgren:
Few fixes for omaps mostly for various devices to get them working
properly on the new am437x and dra7 hardware for several devices
such as I2C, NAND, DDR3 and USB. There's also a clock fix for omap3.
And also included are two minor cosmetic fixes that are not
stictly fixes for the new hardware support added recently to
downgrade a GPMC warning into a debug statement, and fix the
confusing comments for dra7-evm spi1 mux.
Note that these are all .dts changes except for a GPMC change.
* tag 'omap-fixes-against-v3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (255 commits)
ARM: dts: dra7-evm: Add vtt regulator support
ARM: dts: dra7-evm: Fix spi1 mux documentation
ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND
ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am4372: fix USB regs size
ARM: dts: am437x-gp: switch i2c0 to 100KHz
ARM: dts: dra7-evm: Fix 8th NAND partition's name
ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
Linux 3.17-rc3
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- some documentation sync
- resource leak in the bt8xx driver
- again fix the way varargs are used to handle the optional flags on
the gpiod_* accessors. Now hopefully nailed the entire problem.
* tag 'gpio-v3.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: move varargs hack outside #ifdef GPIOLIB
gpio: bt8xx: fix release of managed resources
Documentation: gpio: documentation for optional getters functions
|
|
Pull drm fixes from Dave Airlie:
- i915 fixes: a few display regressions
- vmwgfx: possible loop forever fix
- nouveau: one userspace interface fix
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/core: don't leak oclass type bits to user
drm/i915: Fix lock dropping in intel_tv_detect()
drm/i915: handle G45/GM45 pulse detection connected state.
drm/vmwgfx: Fix a potential infinite spin waiting for fifo idle
drm/vmwgfx: Fix an incorrect OOM return value
drm/i915: Remove bogus __init annotation from DMI callbacks
drm/i915: don't warn if backlight unexpectedly enabled
drm/i915: Move intel_ddi_set_vc_payload_alloc(false) to haswell_crtc_disable()
drm/i915: fix plane/cursor handling when runtime suspended
drm/i915: Ignore VBT backlight presence check on Acer C720 (4005U)
|
|
After commit 2ec2a8be (usb: dwc3: gadget:
always enable IOC on bulk/interrupt transfers)
we created a situation where it was possible to
hang a bulk/interrupt endpoint if we had more
than one pending request in our queue and they
were both started with a single Start Transfer
command.
The problems triggers because we had not enabled
Transfer In Progress event for those endpoints
and we were not able to process early giveback
of requests completed without LST bit set.
Fix the problem by finally enabling Xfer In Progress
event for all endpoint types, except control.
Fixes: 2ec2a8be (usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers)
Cc: <stable@vger.kernel.org> # v3.14+
Reported-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
iommu_group_get_for_dev determines the iommu group for the PCI device and adds
the device to the group.
In the PAMU driver we were again adding the device to the same group without checking
if the device already had an iommu group. This resulted in the following warning.
sysfs: cannot create duplicate filename '/devices/ffe200000.pcie/pci0000:00/0000:00:00.0/iommu_group'
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:31
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0-rc3-00002-g7505cea-dirty #126
task: c0000001fe0a0000 ti: c0000001fe044000 task.ti: c0000001fe044000
NIP: c00000000018879c LR: c000000000188798 CTR: c00000000001ea50
REGS: c0000001fe047040 TRAP: 0700 Not tainted (3.17.0-rc3-00002-g7505cea-dirty)
MSR: 0000000080029000 <CE,EE,ME> CR: 24ad8e22 XER: 20000000
SOFTE: 1
GPR00: c000000000188798 c0000001fe0472c0 c0000000009a52e0 0000000000000065
GPR04: 0000000000000001 0000000000000000 3a30303a00000000 0000000027000000
GPR08: 2f696f6d00000000 c0000000008d3830 c0000000009b3938 c0000000009bb3d0
GPR12: 0000000028ad8e24 c00000000fff4000 c00000000000205c 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 c0000000008a4c70
GPR24: c0000000007e9010 c0000001fe0140a8 ffffffffffffffef 0000000000000001
GPR28: c0000001fe22ebb8 c0000000007e9010 c00000000090bf10 c0000001fe220000
NIP [c00000000018879c] .sysfs_warn_dup+0x74/0xa4
LR [c000000000188798] .sysfs_warn_dup+0x70/0xa4
Call Trace:
[c0000001fe0472c0] [c000000000188798] .sysfs_warn_dup+0x70/0xa4 (unreliable)
[c0000001fe047350] [c000000000188d34] .sysfs_do_create_link_sd.clone.2+0x168/0x174
[c0000001fe047400] [c0000000004b3cf8] .iommu_group_add_device+0x78/0x244
[c0000001fe0474b0] [c0000000004b6964] .fsl_pamu_add_device+0x88/0x1a8
[c0000001fe047570] [c0000000004b3960] .iommu_bus_notifier+0xdc/0x15c
[c0000001fe047600] [c000000000059848] .notifier_call_chain+0x8c/0xe8
[c0000001fe0476a0] [c000000000059d04] .__blocking_notifier_call_chain+0x58/0x84
[c0000001fe047750] [c00000000036619c] .device_add+0x464/0x5c8
[c0000001fe047820] [c000000000300ebc] .pci_device_add+0x14c/0x17c
[c0000001fe0478c0] [c000000000300fbc] .pci_scan_single_device+0xd0/0xf4
[c0000001fe047970] [c00000000030104c] .pci_scan_slot+0x6c/0x18c
[c0000001fe047a10] [c00000000030226c] .pci_scan_child_bus+0x40/0x114
[c0000001fe047ac0] [c000000000021974] .pcibios_scan_phb+0x240/0x2c8
[c0000001fe047b70] [c00000000085a970] .pcibios_init+0x64/0xc8
[c0000001fe047c00] [c000000000001884] .do_one_initcall+0xbc/0x224
[c0000001fe047d00] [c000000000852d50] .kernel_init_freeable+0x14c/0x21c
[c0000001fe047db0] [c000000000002078] .kernel_init+0x1c/0xfa4
[c0000001fe047e30] [c000000000000884] .ret_from_kernel_thread+0x58/0xd4
Instruction dump:
7c7f1b79 4182001c 7fe4fb78 7f83e378 38a01000 4bffc905 60000000 7c641b78
e87e8008 7fa5eb78 48482ff5 60000000 <0fe00000> 7fe3fb78 4bf7bd39 60000000
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
* pm-sleep:
PM / sleep: Fix test_suspend= command line option
* powercap:
powercap / RAPL: change domain detection message
powercap / RAPL: add support for CPU model 0x3f
* pm-domains:
PM / domains: Make generic_pm_domain.name const
* pm-cpufreq:
cpufreq: intel_pstate: Remove unneeded variable
|
|
* acpi-video:
ACPI / video: Disable native_backlight on HP ENVY 15 Notebook PC
ACPI / video: Add a disable_native_backlight quirk
ACPI / video: Fix use_native_backlight selection logic
* acpi-ec:
ACPI / EC: Add msi quirk for Clevo W350etq
|
|
* acpica:
ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.
* acpi-processor:
ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
* acpi-scan:
ACPI / scan: not cache _SUN value in struct acpi_device_pnp
|
|
'regulator/fix/tps65090' into regulator-linus
|
|
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
single fix for nouveau.
* 'linux-3.17' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/core: don't leak oclass type bits to user
|
|
Fixes: 588b48caf65c ("usbip: move usbip userspace code out of staging")
which introduced build failure by not changing uapi/usbip.h include path
according to new location.
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes not being able to init fence subsystem when multiple boards are
present.
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Pull aio bugfixes from Ben LaHaise:
"Two small fixes"
* git://git.kvack.org/~bcrl/aio-fixes:
aio: block exit_aio() until all context requests are completed
aio: add missing smp_rmb() in read_events_ring
|
|
It seems that exit_aio() also needs to wait for all iocbs to complete (like
io_destroy), but we missed the wait step in current implemention, so fix
it in the same way as we did in io_destroy.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org
|
|
The local nohz kick is currently used by perf which needs it to be
NMI-safe. Recent commit though (7d1311b93e58ed55f3a31cc8f94c4b8fe988a2b9)
changed its implementation to fire the local kick using the remote kick
API. It was convenient to make the code more generic but the remote kick
isn't NMI-safe.
As a result:
WARNING: CPU: 3 PID: 18062 at kernel/irq_work.c:72 irq_work_queue_on+0x11e/0x140()
CPU: 3 PID: 18062 Comm: trinity-subchil Not tainted 3.16.0+ #34
0000000000000009 00000000903774d1 ffff880244e06c00 ffffffff9a7f1e37
0000000000000000 ffff880244e06c38 ffffffff9a0791dd ffff880244fce180
0000000000000003 ffff880244e06d58 ffff880244e06ef8 0000000000000000
Call Trace:
<NMI> [<ffffffff9a7f1e37>] dump_stack+0x4e/0x7a
[<ffffffff9a0791dd>] warn_slowpath_common+0x7d/0xa0
[<ffffffff9a07930a>] warn_slowpath_null+0x1a/0x20
[<ffffffff9a17ca1e>] irq_work_queue_on+0x11e/0x140
[<ffffffff9a10a2c7>] tick_nohz_full_kick_cpu+0x57/0x90
[<ffffffff9a186cd5>] __perf_event_overflow+0x275/0x350
[<ffffffff9a184f80>] ? perf_event_task_disable+0xa0/0xa0
[<ffffffff9a01a4cf>] ? x86_perf_event_set_period+0xbf/0x150
[<ffffffff9a187934>] perf_event_overflow+0x14/0x20
[<ffffffff9a020386>] intel_pmu_handle_irq+0x206/0x410
[<ffffffff9a0b54d3>] ? arch_vtime_task_switch+0x63/0x130
[<ffffffff9a01937b>] perf_event_nmi_handler+0x2b/0x50
[<ffffffff9a007b72>] nmi_handle+0xd2/0x390
[<ffffffff9a007aa5>] ? nmi_handle+0x5/0x390
[<ffffffff9a0d131b>] ? lock_release+0xab/0x330
[<ffffffff9a008062>] default_do_nmi+0x72/0x1c0
[<ffffffff9a0c925f>] ? cpuacct_account_field+0xcf/0x200
[<ffffffff9a008268>] do_nmi+0xb8/0x100
Lets fix this by restoring the use of local irq work for the nohz local
kick.
Reported-by: Catalin Iacob <iacobcatalin@gmail.com>
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
This patch fixes setup of second EDMA channel controller
on DA850.
* tag 'davinci-fixes-for-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC
|
|
DRA7 evm REV G and later boards uses a vtt regulator for DDR3
termination and this is controlled by gpio7_11. This gpio is
configured in boot loader. gpio7_11, which is only available only on
Pad A22, in previous boards, is connected only to an unused pad on
expansion connector EXP_P3 and is safe to be muxed as GPIO on all
DRA7-evm versions (without a need to spin off another dts file).
Since gpio7_11 is used to control VTT and should not be reset or kept
in idle state during boot up else VTT will be disconnected and DDR
gets corrupted. So, as part of this change, mark gpio7 as no-reset and
no-idle on init.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
While auditing the various pin ctrl configurations using the following
command:
grep PIN_ arch/arm/boot/dts/dra7-evm.dts|(while read line;
do
v=`echo "$line" | sed -e "s/\s\s*/|/g" | cut -d '|' -f1 |
cut -d 'x' -f2|tr [a-z] [A-Z]`;
HEX=`echo "obase=16;ibase=16;4A003400+$v"| bc`;
echo "$HEX ===> $line";
done)
against DRA75x/74x NDA TRM revision S(SPRUHI2S August 2014),
documentation errors were found for spi1 pinctrl. Fix the same.
Fixes: 6e58b8f1daaf1af ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Both QSPI and GPMC-NAND share the same Pin (A8) from the SoC for Chip Select
functionality. So both can't be enabled simultaneously.
Disable QSPI node to prevent the pin conflict as well as
be similar to 3.12 release.
CC: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For NAND read & write wait pin monitoring must be kept disabled as the
wait pin is only used to indicate NAND device ready status and not to
extend each read/write cycle.
So don't print a warning if wait pin is specified while read/write
monitoring is not in the device tree.
Sanity check wait pin number irrespective if read/write monitoring is
set or not.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
Add gpmc wait pin information as the NAND uses wait pin 0
for device ready indication.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
This patch also gets rid of the below warning when NAND is
accessed for the first time.
omap_l3_noc 44000000.ocp: L3 application error: target 13 mod:1 (unclearable)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am437x-gp-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am43x-epos-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently udf_iget() (triggered by NFS) can race with udf_new_inode()
leading to two inode structures with the same inode number:
nfsd: iget_locked() creates inode
nfsd: try to read from disk, block on that.
udf_new_inode(): allocate inode with that inumber
udf_new_inode(): insert it into icache, set it up and dirty
udf_write_inode(): write inode into buffer cache
nfsd: get CPU again, look into buffer cache, see nice and sane on-disk
inode, set the in-core inode from it
Fix the problem by putting inode into icache in locked state (I_NEW set)
and unlocking it only after it's fully set up.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
boilerplate code in udf_{create,mknod,symlink} taken to new helper
symlink case converted to unique id calculated by udf_new_inode() - no
point finding a new one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently UDF doesn't initialize i_generation in any way and thus NFS
can easily get reallocated inodes from stale file handles. Luckily UDF
already has a unique object identifier associated with each inode -
i_unique. Use that for initialization of i_generation.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
NFS can easily ask for inodes that are already deleted. Currently UDF
happily returns such inodes which is a bug. Return -ESTALE if
udf_read_inode() is asked to read deleted inode.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently __udf_read_inode() wasn't returning anything and we found out
whether we succeeded reading inode by checking whether inode is bad or
not. udf_iget() returned NULL on failure and inode pointer otherwise.
Make these two functions properly propagate errors up the call stack and
use the return value in callers.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
This reverts commit 150b8be3cda54412ad7b54f5392b513b25c0aaa7.
The I2C core's per-adapter locks can't protect from IRQs, so the driver still
needs a spinlock to protect the register accesses.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
Signed-off-by: John W. Linville <linville@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon bugfix from Guenter Roeck:
"Fix a bug in the ds1621 driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ds1621) Update zbits after conversion rate change
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform drivers fixes from Darren Hart:
"This is my first pull request since taking on maintenance for the
platform-drivers-x86 tree from Matthew Garrett. These have passed my
build testing and been run through Fengguang's LKP tests. Due to
timing this round, these have not spent any time in linux-next. I
have asked Stephen to include my for-next branch in linux-next going
forward, once he's back from vacation.
Details from tag:
- toshiba_acpi: re-enable hotkeys and cleanups
- ideapad-laptop: revert touchpad disable, and cleanup static/const
usage
- MAINTAINERS: update platform-drivers-x86 maintainer and tree"
* tag 'platform-drivers-x86-v3.17-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
toshiba_acpi: fix and cleanup toshiba_kbd_bl_mode_store()
platform/x86: toshiba: re-enable acpi hotkeys after suspend to disk
ideapad-laptop: Constify DMI table for real!
Revert "ideapad-laptop: Disable touchpad interface on Yoga models"
MAINTAINERS: Update platform-drivers-x86 maintainer and tree
|
|
When cgroup_kn_lock_live() is called through some kernfs operation and
another thread is calling cgroup_rmdir(), we'll trigger the warning in
cgroup_get().
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1228 at kernel/cgroup.c:1034 cgroup_get+0x89/0xa0()
...
Call Trace:
[<c16ee73d>] dump_stack+0x41/0x52
[<c10468ef>] warn_slowpath_common+0x7f/0xa0
[<c104692d>] warn_slowpath_null+0x1d/0x20
[<c10bb999>] cgroup_get+0x89/0xa0
[<c10bbe58>] cgroup_kn_lock_live+0x28/0x70
[<c10be3c1>] __cgroup_procs_write.isra.26+0x51/0x230
[<c10be5b2>] cgroup_tasks_write+0x12/0x20
[<c10bb7b0>] cgroup_file_write+0x40/0x130
[<c11aee71>] kernfs_fop_write+0xd1/0x160
[<c1148e58>] vfs_write+0x98/0x1e0
[<c114934d>] SyS_write+0x4d/0xa0
[<c16f656b>] sysenter_do_call+0x12/0x12
---[ end trace 6f2e0c38c2108a74 ]---
Fix this by calling css_tryget() instead of cgroup_get().
v2:
- move cgroup_tryget() right below cgroup_get() definition. (Tejun)
Cc: <stable@vger.kernel.org> # 3.15+
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Run these two scripts concurrently:
for ((; ;))
{
mkdir /cgroup/sub
rmdir /cgroup/sub
}
for ((; ;))
{
echo $$ > /cgroup/sub/cgroup.procs
echo $$ > /cgroup/cgroup.procs
}
A kernel bug will be triggered:
BUG: unable to handle kernel NULL pointer dereference at 00000038
IP: [<c10bbd69>] cgroup_put+0x9/0x80
...
Call Trace:
[<c10bbe19>] cgroup_kn_unlock+0x39/0x50
[<c10bbe91>] cgroup_kn_lock_live+0x61/0x70
[<c10be3c1>] __cgroup_procs_write.isra.26+0x51/0x230
[<c10be5b2>] cgroup_tasks_write+0x12/0x20
[<c10bb7b0>] cgroup_file_write+0x40/0x130
[<c11aee71>] kernfs_fop_write+0xd1/0x160
[<c1148e58>] vfs_write+0x98/0x1e0
[<c114934d>] SyS_write+0x4d/0xa0
[<c16f656b>] sysenter_do_call+0x12/0x12
We clear cgrp->kn->priv in the end of cgroup_rmdir(), but another
concurrent thread can access kn->priv after the clearing.
We should move the clearing to css_release_work_fn(). At that time
no one is holding reference to the cgroup and no one can gain a new
reference to access it.
v2:
- move RCU_INIT_POINTER() into the else block. (Tejun)
- remove the cgroup_parent() check. (Tejun)
- update the comment in css_tryget_online_from_dir().
Cc: <stable@vger.kernel.org> # 3.15+
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This time it contains a bunch of small ASoC fixes that slipped from in
previous updates, in addition to the usual HD-audio fixes and the
regression fixes for FireWire updates in 3.17.
All commits are reasonably small fixes"
* tag 'sound-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix COEF setups for ALC1150 codec
ASoC: simple-card: Fix bug of wrong decrement DT node's refcount
ALSA: hda - Fix digital mic on Acer Aspire 3830TG
ASoC: omap-twl4030: Fix typo in 2nd dai link's platform_name
ALSA: firewire-lib/dice: add arrangements of PCM pointer and interrupts for Dice quirk
ALSA: dice: fix wrong channel mappping at higher sampling rate
ASoC: cs4265: Fix setting of functional mode and clock divider
ASoC: cs4265: Fix clock rates in clock map table
ASoC: rt5677: correct mismatch widget name
ASoC: rt5640: Do not allow regmap to use bulk read-write operations
ASoC: tegra: Fix typo in include guard
ASoC: da732x: Fix typo in include guard
ASoC: core: fix .info for SND_SOC_BYTES_TLV
ASoC: rcar: Use && instead of & for boolean expressions
ASoC: Use dev_set_name() instead of init_name
ASoC: axi: Fix ADI AXI SPDIF specification
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.17-rc4
These updates add back some PIDs that were lost in a recent revert and add a
couple of new ones. Included is also an update to how the sierra driver binds
its interfaces in order to avoid binding CDC interfaces.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
If a gref could not be added (perhaps because the limit has been
reached or there are no more grant references available), the undo
path may crash because __del_gref() frees the gref while it is being
used for a list iteration.
A comment suggests that using list_for_each_entry() is safe since the
gref isn't removed from the list being iterated over, but it is freed
and thus list_for_each_entry_safe() must be used.
Also, explicitly delete the gref from the local per-file list, even
though this is not strictly necessary.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
Only set gref->gref_id if foreign access was successfully granted and
the grant ref is valid.
If gref->gref_id == -ENOSPC the test in __del_gref() would incorrectly
attempt to end foreign access (because grant_ref_t is unsigned).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Dave Scott <dave.scott@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
We did not implement any bound on number of indirect ICBs we follow when
loading inode. Thus corrupted medium could cause kernel to go into an
infinite loop, possibly causing a stack overflow.
Fix the possible stack overflow by removing recursion from
__udf_read_inode() and limit number of indirect ICBs we follow to avoid
infinite loops.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
There's no good reason to separate these since udf_fill_inode() is
called only from __udf_read_inode() and both do part of the same thing.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
If we are writing back inode of unlinked directory, its link count ends
up being (u16)-1. Although the inode is deleted, udf_iget() can load the
inode when NFS uses stale file handle and get confused.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
distinguish between the dropped and consumed skb, not assume the skb
is consumed always
Cc: Thomas Graf <tgraf@noironetworks.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
here's a couple of display regression fixes for 3.17.
* tag 'drm-intel-fixes-2014-09-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix lock dropping in intel_tv_detect()
drm/i915: handle G45/GM45 pulse detection connected state.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov:
"A fix for MT breakage, enhancement to Elantech PS/2 driver and a
couple of assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add support for trackpoint found on some v3 models
Input: elantech - reset the device when elantech probe fails
Input: ALPS - suppress message about 'Unknown touchpad'
Input: fix used slots detection breakage
Input: sparc - i8042-sparcio.h: fix unused kbd_res warning
Input: atmel_mxt_ts - improve description of gpio-keymap property
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Several bug fixes for issues that have been lurking for a while:
- Check that devices haven't set the flag saying they only support
register at a time operation while we're doing cache syncs,
otherwise we fail to restore caches
- Ensure that we don't mark all registers on devices using
format_write() as cacheable, avoiding adding a cache of things like
reset registers which we don't want to rewrite during cache sync
- Make sure we create the debugfs files in the correct directory"
* tag 'regmap-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Don't attempt block writes when syncing cache on single_rw devices
regmap: Fix handling of volatile registers for format_write() chips
regmap: Fix regcache debugfs initialization
|
|
we don't to gate clocks until our children are
done with their remove path.
Fixes: af310e9 (usb: dwc3: omap: use runtime API's to enable clocks)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
