summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-12-11mlxsw: spectrum_acl: Limit priority valueNir Dotan
In Spectrum-2, higher priority value wins and priority valid values are in the range of {1,cap_kvd_size-1}. mlxsw_sp_acl_tcam_priority_get converts from lower-bound priorities alike tc flower to Spectrum-2 HW range. Up until now tc flower did not provide priority 0 or reached the maximal value, however multicast routing does provide priority 0. Therefore, Change mlxsw_sp_acl_tcam_priority_get to verify priority is in the correct range. Make sure priority is never set to zero and never exceeds the maximal allowed value. Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-11mlxsw: spectrum_acl: Support rule creation without action creationNir Dotan
Up until now, when ACL rule was created its action was created with it. It suits well for tc flower where ACL rule always needs an action, however it does not suit multicast router, where the action is created prior to setting a route, which in Spectrum-2 is actually an ACL rule. Add support for rule creation without action creation. Do it by adding afa_block argument to mlxsw_sp_acl_rule_create, which if NULL then an action would be created, also add an indication within struct mlxsw_sp_acl_rule_info that tells if the action should be destroyed when the rule is destroyed. Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-11mlxsw: spectrum_acl: Add replace rule action operationNir Dotan
Multicast routes actions may be updated after creation. An example for that is an addition of an egress interface to an existing route. So far, as tc flower API dictated, ACL rules were either created or deleted. Since multicast routes in Spectrum-2 are written to ACL as any rule, it is required to allow the update of a rule's action as it may change. Add methods and operations to support updating rule's action. This is supported only for Spectrum-2. Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-11mlxsw: spectrum_acl: Add multicast router profile operationsNir Dotan
Add specific ACL operations needed for programming multicast routing ACL groups and routes. Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-11mlxsw: spectrum_acl: Add Spectrum-2 keysNir Dotan
Add virtual router ID fields to Spectrum-2 key blocks set, as the field is required for multicast routing. Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-11mlxsw: spectrum: Change stage of ACL initializationNir Dotan
In Spectrum-2, MC routing is implemented using ACL block explicitly, so router initialization should take place after ACL initialization. Set the initialization of the ACL block before IP router initizalization takes place, so multicast router will be able to allocate ACL data structures and create its required chains. Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-11mlxsw: reg: Add Policy Engine Multicast Router Binding Table RegisterNir Dotan
In Spectrum-2, multicast routing is implemented explicitly using policy engine (ACL) block. PEMRBT register is used to bind a dedicated ACL group to a specific IP protocol. Add the register to be later used in multicast router implementation. Signed-off-by: Nir Dotan <nird@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-11hinic: optmize rx refill buffer mechanismXue Chaojing
There is no need to schedule a different tasklet for refill, This patch remove it. Suggested-by: Neil Horman <nhorman@redhat.com> Signed-off-by: Xue Chaojing <xuechaojing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-11net/mlx5e: Use monitor counters for update statsEyal Davidovich
- Adding new notifier block (struct mlx5_nb) monitor_counters_nb for handeling MONITOR_COUNTER new event type. - Adding work queue element: monitor_counters_work for re-arm and update stats. - We re-queue the update stat work, only when working over firmware that doesn't support the monitored counters. Signed-off-by: Eyal Davidovich <eyald@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5e: Monitor counters commands supportEyal Davidovich
new file monitor_stats.c for the new API. add arm_monitor_counter new command support. add set_monitor_counter new command support. The device can monitor specific counters and provide an event to notify when these counters are changed. The monitoring is done in best effort manner where the minimum notification period is 200 ms, however when the device is loaded, the notification might be delayed. To configure the required counters to be monitored, the SET_MONITOR_COUNTER command shall be used with a list of counters to be monitored. The device firmware can monitor up to HCA_CAP.max_num_of_monitor_counters. The configuration is done based on counter type (such as ppcnt, q counter, etc) and additional param according to the type of counter selected. Upon monitor counter change, the device will generate Monitor_Counter_Change event. The device will not generate new events unless the driver re-arms the monitoring functionality, using the ARM_MONITOR_COUNTER command. Signed-off-by: Eyal Davidovich <eyald@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5e: Avoid query PPCNT register if not supported by the deviceEyal Davidovich
PPCNT is not supported if PCAM access reg is supported and ppcnt bit is clear. Signed-off-by: Eyal Davidovich <eyald@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5e: Use CQE padding for Ethernet CQsDaniel Jurgens
Writing 64B CQEs to 128B cache lines results in a RMW operation. Padding the CQEs to 128B if possible improves performance on 128B cache line systems like PPC. Testing on PPC showed up to a 24% improvement in small packet throughput vs the default behavior, depending on the workload and system topology. Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5e: Support multiple encapsulations for a TC flowEli Britstein
Currently a flow is associated with a single encap structure. The FW extended destination features enables the driver to associate a flow with multiple encap instances. Change the encap id field from a flow scope to a per destination value in the flow attributes struct. Use the encaps array to associate a flow table entry with multiple encap entries. Update the neigh logic to offload only if all encapsulations used in a flow are connected, and un-offload upon the first one disconnected. Note that the driver can now support up to two encap destinations. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5e: Allow association of a flow to multiple encapsEli Britstein
Currently a flow can be associated with a single encap entry. The extended destination feature enables the driver to configure multiple encap entries per flow. Change the encap flow association field to array as a pre-step towards supporting multiple encap destinations. Use only the first array element, with no functional change. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5e: Change parse attr struct to accommodate multiple tunnel infosEli Britstein
Currently the driver can support only a single TC tunnel_set action. Change the tunnel info fields to arrays, as a pre-step to support multiple encapsulations for a single flow, with no functional change. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5e: Support header rewrite actions with remote port mirroringEli Britstein
A rule with the following actions is split to a two level FDB: 1. Forward to local mirror vport 2. Header rewrite 3. Forward to local vport In the first level flow table, forward the packet to the local port and forward the packet to the second level flow table for header rewrite and local port forwarding. This configuration fails when mirroring to a remote encapsulated destination because currently an FTE cannot support encap and table destinations. Use the extended destination capabilities to configure the first level flow table with a multi-destination FTE to the uplink and second level table and the second level flow table for the header rewrite and local port forwarding. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5e: Replace the split logic with extended destinationEli Britstein
Currently the FTE encap flag applies to all destinations. To support mirroring encapsulated traffic to a local port the driver split the two destinations to two flow table entries: Table#0: - FWD to the local vport - Goto table#1 Table#1: - Encap and FWD to wire The firmware extended destination capabilities enable the driver to set an encapsulation flag per destination. Remove the split logic and use the extended destination mechanism instead. Note that split technique is still required for pedit and VLAN push scenarios. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5e: Annul encap action ordering requirementEli Britstein
Currently a FW syndrome is emitted if the driver configures a multi-destination FTE where the first destination is a tunneled uplink port and the second destination is a local vPort. Support this scenario by creating a multi-destination FTE using the firmware's extended destination capabilities. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5e: Move flow attr reformat action bit to per dest flagsEli Britstein
Flow attr reformat action bit is moved from the global action bits to a per destination flags field, as a pre-step for adding additional flags to support encapsulation properties per destination, with no functionality change. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5e: Refactor eswitch flow attr for destination specific propertiesEli Britstein
Currently the eswitch flow attr structure stores each destination specific property in its own specific array. Group them in an array of destination structures as a pre-step towards adding additional destination specific field properties. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5: E-Switch, Rename esw attr mirror count fieldEli Britstein
The mirror count esw attributes field is used to determine if splitting the rule to two FTEs is required while programming e-switch mirroring. Rename it to split count, making it clearer with no functional change. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11net/mlx5: Consider encapsulation properties when comparing destinationsEli Britstein
Currently the driver identifies identical vport destinations by comparing the vport ID. The FW extended destination feature enables the driver to forward the packet to the same vport with multiple encapsulation properties. Change the vport destination comparison logic to compare the encapsulation properties in addition to the vport ID. Signed-off-by: Eli Britstein <elibr@mellanox.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-11bpf: fix up uapi helper description and sync bpf header with toolsDaniel Borkmann
Minor markup fixup from bpf-next into net-next merge in the BPF helper description of bpf_sk_lookup_tcp() and bpf_sk_lookup_udp(). Also sync up the copy of bpf.h from tooling infrastructure. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextDavid S. Miller
Daniel Borkmann says: ==================== pull-request: bpf-next 2018-12-11 The following pull-request contains BPF updates for your *net-next* tree. It has three minor merge conflicts, resolutions: 1) tools/testing/selftests/bpf/test_verifier.c Take first chunk with alignment_prevented_execution. 2) net/core/filter.c [...] case bpf_ctx_range_ptr(struct __sk_buff, flow_keys): case bpf_ctx_range(struct __sk_buff, wire_len): return false; [...] 3) include/uapi/linux/bpf.h Take the second chunk for the two cases each. The main changes are: 1) Add support for BPF line info via BTF and extend libbpf as well as bpftool's program dump to annotate output with BPF C code to facilitate debugging and introspection, from Martin. 2) Add support for BPF_ALU | BPF_ARSH | BPF_{K,X} in interpreter and all JIT backends, from Jiong. 3) Improve BPF test coverage on archs with no efficient unaligned access by adding an "any alignment" flag to the BPF program load to forcefully disable verifier alignment checks, from David. 4) Add a new bpf_prog_test_run_xattr() API to libbpf which allows for proper use of BPF_PROG_TEST_RUN with data_out, from Lorenz. 5) Extend tc BPF programs to use a new __sk_buff field called wire_len for more accurate accounting of packets going to wire, from Petar. 6) Improve bpftool to allow dumping the trace pipe from it and add several improvements in bash completion and map/prog dump, from Quentin. 7) Optimize arm64 BPF JIT to always emit movn/movk/movk sequence for kernel addresses and add a dedicated BPF JIT backend allocator, from Ard. 8) Add a BPF helper function for IR remotes to report mouse movements, from Sean. 9) Various cleanups in BPF prog dump e.g. to make UAPI bpf_prog_info member naming consistent with existing conventions, from Yonghong and Song. 10) Misc cleanups and improvements in allowing to pass interface name via cmdline for xdp1 BPF example, from Matteo. 11) Fix a potential segfault in BPF sample loader's kprobes handling, from Daniel T. 12) Fix SPDX license in libbpf's README.rst, from Andrey. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-10neighbor: gc_list changes should be protected by table lockDavid Ahern
Adding and removing neighbor entries to / from the gc_list need to be done while holding the table lock; a couple of places were missed in the original patch. Move the list_add_tail in neigh_alloc to ___neigh_create where the lock is already obtained. Since neighbor entries should rarely be moved to/from PERMANENT state, add lock/unlock around the gc_list changes in neigh_change_state rather than extending the lock hold around all neighbor updates. Fixes: 58956317c8de ("neighbor: Improve garbage collection") Reported-by: Andrei Vagin <avagin@gmail.com> Reported-by: syzbot+6cc2fd1d3bdd2e007363@syzkaller.appspotmail.com Reported-by: syzbot+35e87b87c00f386b041f@syzkaller.appspotmail.com Reported-by: syzbot+b354d1fb59091ea73c37@syzkaller.appspotmail.com Reported-by: syzbot+3ddead5619658537909b@syzkaller.appspotmail.com Reported-by: syzbot+424d47d5c456ce8b2bbe@syzkaller.appspotmail.com Reported-by: syzbot+e4d42eb35f6a27b0a628@syzkaller.appspotmail.com Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-10Merge tag 'mlx5e-updates-2018-12-10' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed: ==================== mlx5e-updates-2018-12-10 (gre) This patch set adds GRE offloading support to Mellanox ethernet driver. Patches 1-5 replace the existing egdev mechanism with the new TC indirect block binds mechanism that was introduced by Netronome: 7f76fa36754b ("net: sched: register callbacks for indirect tc block binds") Patches 6-9 add GRE offloading support along with some required refactoring work. Patch 10, Add netif_is_gretap()/netif_is_ip6gretap() - Changed the is_gretap_dev and is_ip6gretap_dev logic from structure comparison to string comparison of the rtnl_link_ops kind field. Patch 11, add GRE offloading support to mlx5. Patch 12 removes the egdev mechanism from TC as it is no longer used by any of the drivers. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-10net/sched: Remove egdev mechanismOz Shlomo
The egdev mechanism was replaced by the TC indirect block notifications platform. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Cc: John Hurley <john.hurley@netronome.com> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5e: Add GRE protocol offloadingOz Shlomo
Add HW offloading support for TC flower filters configured on gretap/ip6gretap net devices. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net: Add netif_is_gretap()/netif_is_ip6gretap()Oz Shlomo
Changed the is_gretap_dev and is_ip6gretap_dev logic from structure comparison to string comparison of the rtnl_link_ops kind field. This approach aligns with the current identification methods and function names of vxlan and geneve network devices. Convert mlxsw to use these helpers and use them in downstream mlx5 patch. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5e: Move TC tunnel offloading code to separate source fileOz Shlomo
Move tunnel offloading related code to a separate source file for better code maintainability. Code refactoring with no functional change. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5e: Branch according to classified tunnel typeOz Shlomo
Currently the tunnel offloading encap/decap methods assumes that VXLAN is the sole tunneling protocol. Lay the infrastructure for supporting multiple tunneling protocols by branching according to the tunnel net device kind. Encap filters tunnel type is determined according to the egress/mirred net device. Decap filters classify the tunnel type according to the filter's ingress net device kind. Distinguish between the tunnel type as defined by the SW model and the FW reformat type that specifies the HW operation being made. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5e: Refactor VXLAN tunnel decap offloading codeOz Shlomo
Separates the vxlan header match handling from the matching on the general fields of ipv4/6 tunnels, thus allowing the common IP tunnel match code to branch in down stream patch, to multiple IP tunnels. This patch doesn't add any functionality. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5e: Refactor VXLAN tunnel encap offloading codeOz Shlomo
Separates the vxlan header encap logic from the general ipv4/6 encapsulation methods, thus allowing the common IP encap/decap code to branch in downstream patch to multiple IP tunnels. Code refactoring with no functional change. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5e: Replace egdev with indirect block notificationsOz Shlomo
Use TC indirect block notifications to offload filters that are configured on higher level device interfaces (e.g. tunnel devices). This mechanism replaces the current egdev implementation. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5e: Propagate the filter's net device to mlx5e structuresOz Shlomo
Propagate the filter's net_device parameter to the tc flower parsed attributes structure so that it can later be used in tunnel decap offloading sequences. Pre-step for replacing egdev logic with the indirect block notification mechanism. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5e: Provide the TC filter netdev as parameter to flower callbacksOz Shlomo
Currently the driver controls flower filters that are installed on its devices. However, with the introduction of the indirect block notifications platform the driver may receive control events for filters that are installed on higher level net devices (e.g. tunnel devices). Therefore, the driver filter control API will not be able to implicitly assume the filter's net device. Explicitly specify the filter's net device, no functional change Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5e: Support TC indirect block notifications for eswitch uplink reprsOz Shlomo
Towards using this mechanism as the means to offload tunnel decap rules set on SW tunnel devices instead of egdev, add the supporting structures and functions. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5e: Store eswitch uplink representor state on a dedicated structOz Shlomo
Currently only a single field in the representor private structure is relevant for uplink representors. As a pre-step to allow adding additional uplink representor fields, introduce uplink representor private structure. This is prepration step towards replacing egdev logic with the indirect block notification mechanism. This patch doesn't change any functionality. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10Merge branch 'mlx5-next' of ↵Saeed Mahameed
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux mlx5-next shared branch with rdma subtree to avoid mlx5 rdma v.s. netdev conflicts. Highlights: 1) RDMA ODP (On Demand Paging) improvements and moving ODP logic to mlx5 RDMA driver 2) Improved mlx5 core driver and device events handling and provided API for upper layers to subscribe to device events. 3) RDMA only code cleanup from mlx5 core 4) Add helper to get CQE opcode 5) Rework handling of port module events 6) shared mlx5_ifc.h updates to avoid conflicts Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10Merge branch 'rename-info_cnt-to-nr_info'Alexei Starovoitov
Yonghong Song says: ==================== Before func_info and line_info are added to the kernel, there are several fields in structure bpf_prog_info specifying the "count" of a user buffer, e.g., __u32 nr_jited_ksyms; __u32 nr_jited_func_lens; The naming convention has the prefix "nr_". The func_info and line_info support added several fields __u32 func_info_cnt; __u32 line_info_cnt; __u32 jited_line_info_cnt; to indicate the "count" of buffers func_info, line_info and jited_line_info. The original intention is to keep the field names the same as those in structure bpf_attr, so it will be clear that the "count" returned to user space will be the same as the one passed to the kernel during prog load. Unfortunately, the field names *_info_cnt are not consistent with other existing fields in bpf_prog_info. This patch set renamed the fields *_info_cnt to nr_*_info to keep naming convention consistent. ==================== Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-12-10tools/bpf: rename *_info_cnt to nr_*_infoYonghong Song
Rename all occurances of *_info_cnt field access to nr_*_info in tools directory. The local variables finfo_cnt, linfo_cnt and jited_linfo_cnt in function do_dump() of tools/bpf/bpftool/prog.c are also changed to nr_finfo, nr_linfo and nr_jited_linfo to keep naming convention consistent. Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-12-10tools/bpf: sync kernel uapi bpf.h to tools directoryYonghong Song
Sync kernel uapi bpf.h "*_info_cnt => nr_*_info" changes to tools directory. Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-12-10bpf: rename *_info_cnt to nr_*_info in bpf_prog_infoYonghong Song
In uapi bpf.h, currently we have the following fields in the struct bpf_prog_info: __u32 func_info_cnt; __u32 line_info_cnt; __u32 jited_line_info_cnt; The above field names "func_info_cnt" and "line_info_cnt" also appear in union bpf_attr for program loading. The original intention is to keep the names the same between bpf_prog_info and bpf_attr so it will imply what we returned to user space will be the same as what the user space passed to the kernel. Such a naming convention in bpf_prog_info is not consistent with other fields like: __u32 nr_jited_ksyms; __u32 nr_jited_func_lens; This patch made this adjustment so in bpf_prog_info newly introduced *_info_cnt becomes nr_*_info. Acked-by: Song Liu <songliubraving@fb.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-12-10bpf: clean up bpf_prog_get_info_by_fd()Song Liu
info.nr_jited_ksyms and info.nr_jited_func_lens cannot be 0 in these two statements, so we don't need to check them. Signed-off-by: Song Liu <songliubraving@fb.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-12-10net/mlx5: Remove the get protocol device interface entryOr Gerlitz
This isn't used anywhere across the mlx5 driver stack, remove it. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5: Support extended destination format in flow steering commandEli Britstein
Update the flow steering command formatting according to the extended destination API. Note that the FW dictates that multi destination FTEs that involve at least one encap must use the extended destination format, while single destination ones must use the legacy format. Using extended destination format requires FW support. Check for its capabilities and return error if not supported. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5: E-Switch, Change vhca id valid bool field to bit flagEli Britstein
Change the driver flow destination struct to use bit flags with the vhca id valid being the 1st one. The flags field is more extendable and will be used in downstream patch. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5: Introduce extended destination fieldsEli Britstein
Extended destinations provide the ability to configure different encapsulation properties per destination on a single FTE. This is needed for use-cases such as remote mirroring over tunneled networks. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5: Revise gre and nvgre key formatsOz Shlomo
GRE RFC defines a 32 bit key field. NVGRE RFC splits the 32 bit key field to 24 bit VSID (gre_key_h) and 8 bit flow entropy (gre_key_l). Define the two key parsing alternatives in a union, thus enabling both access methods. Signed-off-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Eli Britstein <elibr@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2018-12-10net/mlx5: Add monitor commands layout and event dataEyal Davidovich
Will be used in downstream patch to monitor counter changes by the HCA and report it to the driver by an event. The driver will update its counters cached data accordingly. Signed-off-by: Eyal Davidovich <eyald@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-29 04:49:58 +0000