| Age | Commit message (Collapse) | Author |
|---|
|
The compatible string list for SDHCI on Tegra234 should be
"nvidia,tegra234-sdhci", followed by the "nvidia,tegra186-sdhci"
fallback. Use that consistently for all SDHCI controllers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra QSPI controller uses a single reset line, so there's no need
for a reset-names property. Remove such properties.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Pinmux node names should have a pinmux- prefix and not use underscores.
Fix up some cases that didn't follow those rules.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra QSPI controllers use a single reset control, so reset-names is
not necessary and therefore not specified in the DT bindings. Drop the
property from device tree files to avoid validation warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra234 HDA controller is not backwards-compatible with Tegra30, so
drop the corresponding compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra194 HDA controller is not backwards-compatible with Tegra30, so
drop the corresponding compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Instead of using the deprecated vbus-gpio property, switch to using the
more standard vbus-gpios property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The PMC pinmux configuration nodes need to be part of a top-level pinmux
node. Add that new "pinmux" node and move the configuration nodes into
it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The DeviceTree Specification v0.3 specifies that the cache node
'compatible' and 'cache-level' properties are 'required'. Cf.
s3.8 Multi-level and Shared Cache Nodes
The 'cache-unified' property should be present if one of the
properties for unified cache is present ('cache-size', ...).
Update the Device Trees accordingly.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The 'enable-active-low' property is not a valid one.
Only 'enable-active-high' is valid, and when this property is absent
the gpio regulator will act as active low by default.
Remove the invalid 'enable-active-low' property.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add dma-channel-mask property in Tegra GPCDMA device tree node.
The property would help to specify the channels to be used in
kernel and reserve few for the firmware. This was previously
achieved by limiting the channel number to 31 in the driver.
This is wrong and does not align with the hardware. Correct this
and update the interrupts property to list all 32 interrupts.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Fix the starting address of the non-prefetchable aperture of PCIe C3
controller.
Fixes: ec142c44b026 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra234 DT")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
According to the DT schema in usb-device.yaml, each USB device node
needs a compatible string, so add one for the built-in USB Ethernet
device on Jetson TX1.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The registers for the AON pinmux reside in a partition different from
the registers for the main pinmux. Instead of treating them as one and
the same device, split them up so that they are each their own devices.
Also add gpio-ranges properties to the corresponding GPIO controllers
such that the pinmux and GPIO controllers can be paired up properly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the ECAM aperture information for all the PCIe controllers of
Tegra234.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra PWFM controllers use a single clock, so there's no need for a
clock-names property.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add and enable AON and LIC GTE nodes by default.
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra Combined UART (TCU) is the default serial interface for Jetson
Xavier and Orin platforms and so update the bootargs for these platforms
to use the TCU.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Enable additional PWM controllers in device tree so that the PWM pins on
the Jetson AGX Orin Developer Kit 40-pin header can be used.
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The unit-address of a node should be separated from the opening brace by
a space.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The P2U nodes that were recently added were not added in the correct
order. Sort them in the right place by unit-address.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add device tree node for Tegra234 SDMMC1 instance.
Add and enable SD card instance in device tree.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Populate the SBSA UART for Tegra234 and enable this UART for Jetson AGX
Orin.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the PWM fan node for the Tegra234 Jetson AGX Orin platform.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Populate all the PWM devices for Tegra234. Finally, update the
compatible string for the existing 'pwm1' node to just be 'tegra194-pwm'
and remove the fallback to 'tegra186-pwm', which aligns with the
binding documentation.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Commit 156af9de0932 ("arm64: tegra: Add Tegra234 I2C devicetree nodes")
populated the I2C device nodes for Tegra234. One of these nodes
contains the property 'nvidia,hw-instance-id' which is neither
documented or used. Remove this unused property.
Fixes: 156af9de0932 ("arm64: tegra: Add Tegra234 I2C devicetree nodes")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
commit edf408b946d3 ("PCI: dwc: Validate iATU outbound mappings against
hardware constraints") exposes an issue with the existing partitioning of
the aperture space where the Prefetchable apertures of controllers
C5, C7 and C9 in Tegra234 cross the 32GB boundary hardware constraint.
This patch makes sure that the Prefetchable region doesn't spill over
the 32GB boundary.
Fixes: ec142c44b026 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra234 DT")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a device tree node for NVDEC on Tegra234.
Booting the firmware requires some information regarding offsets
within the firmware binary. These are passed through the device
tree, but since the values vary depending on the firmware version,
and the firmware itself is not available to the OS, the flasher is
expected to provide a device tree overlay with values corresponding
to the firmware it is flashing. The overlay then replaces the
placeholder values here.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The currently specified 'ranges' properties don't actually include
all devices under the host1x bus on Tegra194 and Tegra234. Expand
them appropriately.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
|
|
Update the device-tree clock, memory, power and reset headers for
Tegra234 by adding the definitions for all the various devices.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add clock, memory controller, powergate and reset dt-binding headers
necessary for NVDEC.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull more random number generator updates from Jason Donenfeld:
"This time with some large scale treewide cleanups.
The intent of this pull is to clean up the way callers fetch random
integers. The current rules for doing this right are:
- If you want a secure or an insecure random u64, use get_random_u64()
- If you want a secure or an insecure random u32, use get_random_u32()
The old function prandom_u32() has been deprecated for a while
now and is just a wrapper around get_random_u32(). Same for
get_random_int().
- If you want a secure or an insecure random u16, use get_random_u16()
- If you want a secure or an insecure random u8, use get_random_u8()
- If you want secure or insecure random bytes, use get_random_bytes().
The old function prandom_bytes() has been deprecated for a while
now and has long been a wrapper around get_random_bytes()
- If you want a non-uniform random u32, u16, or u8 bounded by a
certain open interval maximum, use prandom_u32_max()
I say "non-uniform", because it doesn't do any rejection sampling
or divisions. Hence, it stays within the prandom_*() namespace, not
the get_random_*() namespace.
I'm currently investigating a "uniform" function for 6.2. We'll see
what comes of that.
By applying these rules uniformly, we get several benefits:
- By using prandom_u32_max() with an upper-bound that the compiler
can prove at compile-time is ≤65536 or ≤256, internally
get_random_u16() or get_random_u8() is used, which wastes fewer
batched random bytes, and hence has higher throughput.
- By using prandom_u32_max() instead of %, when the upper-bound is
not a constant, division is still avoided, because
prandom_u32_max() uses a faster multiplication-based trick instead.
- By using get_random_u16() or get_random_u8() in cases where the
return value is intended to indeed be a u16 or a u8, we waste fewer
batched random bytes, and hence have higher throughput.
This series was originally done by hand while I was on an airplane
without Internet. Later, Kees and I worked on retroactively figuring
out what could be done with Coccinelle and what had to be done
manually, and then we split things up based on that.
So while this touches a lot of files, the actual amount of code that's
hand fiddled is comfortably small"
* tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
prandom: remove unused functions
treewide: use get_random_bytes() when possible
treewide: use get_random_u32() when possible
treewide: use get_random_{u8,u16}() when possible, part 2
treewide: use get_random_{u8,u16}() when possible, part 1
treewide: use prandom_u32_max() when possible, part 2
treewide: use prandom_u32_max() when possible, part 1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Use BPF CO-RE (Compile Once, Run Everywhere) to support old kernels
when using bperf (perf BPF based counters) with cgroups.
- Support HiSilicon PCIe Performance Monitoring Unit (PMU), that
monitors bandwidth, latency, bus utilization and buffer occupancy.
Documented in Documentation/admin-guide/perf/hisi-pcie-pmu.rst.
- User space tasks can migrate between CPUs, so when tracing selected
CPUs, system-wide sideband is still needed, fix it in the setup of
Intel PT on hybrid systems.
- Fix metricgroups title message in 'perf list', it should state that
the metrics groups are to be used with the '-M' option, not '-e'.
- Sync the msr-index.h copy with the kernel sources, adding support for
using "AMD64_TSC_RATIO" in filter expressions in 'perf trace' as well
as decoding it when printing the MSR tracepoint arguments.
- Fix program header size and alignment when generating a JIT ELF in
'perf inject'.
- Add multiple new Intel PT 'perf test' entries, including a jitdump
one.
- Fix the 'perf test' entries for 'perf stat' CSV and JSON output when
running on PowerPC due to an invalid topology number in that arch.
- Fix the 'perf test' for arm_coresight failures on the ARM Juno
system.
- Fix the 'perf test' attr entry for PERF_FORMAT_LOST, adding this
option to the or expression expected in the intercepted
perf_event_open() syscall.
- Add missing condition flags ('hs', 'lo', 'vc', 'vs') for arm64 in the
'perf annotate' asm parser.
- Fix 'perf mem record -C' option processing, it was being chopped up
when preparing the underlying 'perf record -e mem-events' and thus
being ignored, requiring using '-- -C CPUs' as a workaround.
- Improvements and tidy ups for 'perf test' shell infra.
- Fix Intel PT information printing segfault in uClibc, where a NULL
format was being passed to fprintf.
* tag 'perf-tools-for-v6.1-2-2022-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (23 commits)
tools arch x86: Sync the msr-index.h copy with the kernel sources
perf auxtrace arm64: Add support for parsing HiSilicon PCIe Trace packet
perf auxtrace arm64: Add support for HiSilicon PCIe Tune and Trace device driver
perf auxtrace arm: Refactor event list iteration in auxtrace_record__init()
perf tests stat+json_output: Include sanity check for topology
perf tests stat+csv_output: Include sanity check for topology
perf intel-pt: Fix system_wide dummy event for hybrid
perf intel-pt: Fix segfault in intel_pt_print_info() with uClibc
perf test: Fix attr tests for PERF_FORMAT_LOST
perf test: test_intel_pt.sh: Add 9 tests
perf inject: Fix GEN_ELF_TEXT_OFFSET for jit
perf test: test_intel_pt.sh: Add jitdump test
perf test: test_intel_pt.sh: Tidy some alignment
perf test: test_intel_pt.sh: Print a message when skipping kernel tracing
perf test: test_intel_pt.sh: Tidy some perf record options
perf test: test_intel_pt.sh: Fix return checking again
perf: Skip and warn on unknown format 'configN' attrs
perf list: Fix metricgroups title message
perf mem: Fix -C option behavior for perf mem record
perf annotate: Add missing condition flags for arm64
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y compile error for the
combination of Clang >= 14 and GAS <= 2.35.
- Drop vmlinux.bz2 from the rpm package as it just annoyingly increased
the package size.
- Fix modpost error under build environments using musl.
- Make *.ll files keep value names for easier debugging
- Fix single directory build
- Prevent RISC-V from selecting the broken DWARF5 support when Clang
and GAS are used together.
* tag 'kbuild-fixes-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
lib/Kconfig.debug: Add check for non-constant .{s,u}leb128 support to DWARF5
kbuild: fix single directory build
kbuild: add -fno-discard-value-names to cmd_cc_ll_c
scripts/clang-tools: Convert clang-tidy args to list
modpost: put modpost options before argument
kbuild: Stop including vmlinux.bz2 in the rpm's
Kconfig.debug: add toolchain checks for DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT
Kconfig.debug: simplify the dependency of DEBUG_INFO_DWARF4/5
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk updates from Stephen Boyd:
"This is the final part of the clk patches for this merge window.
The clk rate range series needed another week to fully bake. Maxime
fixed the bug that broke clk notifiers and prevented this from being
included in the first pull request. He also added a unit test on top
to make sure it doesn't break so easily again. The majority of the
series fixes up how the clk_set_rate_*() APIs work, particularly
around when the rate constraints are dropped and how they move around
when reparenting clks. Overall it's a much needed improvement to the
clk rate range APIs that used to be pretty broken if you looked
sideways.
Beyond the core changes there are a few driver fixes for a compilation
issue or improper data causing clks to fail to register or have the
wrong parents. These are good to get in before the first -rc so that
the system actually boots on the affected devices"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (31 commits)
clk: tegra: Fix Tegra PWM parent clock
clk: at91: fix the build with binutils 2.27
clk: qcom: gcc-msm8660: Drop hardcoded fixed board clocks
clk: mediatek: clk-mux: Add .determine_rate() callback
clk: tests: Add tests for notifiers
clk: Update req_rate on __clk_recalc_rates()
clk: tests: Add missing test case for ranges
clk: qcom: clk-rcg2: Take clock boundaries into consideration for gfx3d
clk: Introduce the clk_hw_get_rate_range function
clk: Zero the clk_rate_request structure
clk: Stop forwarding clk_rate_requests to the parent
clk: Constify clk_has_parent()
clk: Introduce clk_core_has_parent()
clk: Switch from __clk_determine_rate to clk_core_round_rate_nolock
clk: Add our request boundaries in clk_core_init_rate_req
clk: Introduce clk_hw_init_rate_request()
clk: Move clk_core_init_rate_req() from clk_core_round_rate_nolock() to its caller
clk: Change clk_core_init_rate_req prototype
clk: Set req_rate on reparenting
clk: Take into account uncached clocks in clk_set_rate_range()
...
|
|
git://git.samba.org/sfrench/cifs-2.6
Pull more cifs updates from Steve French:
- fix a regression in guest mounts to old servers
- improvements to directory leasing (caching directory entries safely
beyond the root directory)
- symlink improvement (reducing roundtrips needed to process symlinks)
- an lseek fix (to problem where some dir entries could be skipped)
- improved ioctl for returning more detailed information on directory
change notifications
- clarify multichannel interface query warning
- cleanup fix (for better aligning buffers using ALIGN and round_up)
- a compounding fix
- fix some uninitialized variable bugs found by Coverity and the kernel
test robot
* tag '6.1-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: improve SMB3 change notification support
cifs: lease key is uninitialized in two additional functions when smb1
cifs: lease key is uninitialized in smb1 paths
smb3: must initialize two ACL struct fields to zero
cifs: fix double-fault crash during ntlmssp
cifs: fix static checker warning
cifs: use ALIGN() and round_up() macros
cifs: find and use the dentry for cached non-root directories also
cifs: enable caching of directories for which a lease is held
cifs: prevent copying past input buffer boundaries
cifs: fix uninitialised var in smb2_compound_op()
cifs: improve symlink handling for smb2+
smb3: clarify multichannel warning
cifs: fix regression in very old smb1 mounts
cifs: fix skipping to incorrect offset in emit_cached_dirents
|
|
This reverts commit 78e5a3399421 ("cpumask: fix checking valid cpu range").
syzbot is hitting WARN_ON_ONCE(cpu >= nr_cpumask_bits) warning at
cpu_max_bits_warn() [1], for commit 78e5a3399421 ("cpumask: fix checking
valid cpu range") is broken. Obviously that patch hits WARN_ON_ONCE()
when e.g. reading /proc/cpuinfo because passing "cpu + 1" instead of
"cpu" will trivially hit cpu == nr_cpumask_bits condition.
Although syzbot found this problem in linux-next.git on 2022/09/27 [2],
this problem was not fixed immediately. As a result, that patch was
sent to linux.git before the patch author recognizes this problem, and
syzbot started failing to test changes in linux.git since 2022/10/10
[3].
Andrew Jones proposed a fix for x86 and riscv architectures [4]. But
[2] and [5] indicate that affected locations are not limited to arch
code. More delay before we find and fix affected locations, less tested
kernel (and more difficult to bisect and fix) before release.
We should have inspected and fixed basically all cpumask users before
applying that patch. We should not crash kernels in order to ask
existing cpumask users to update their code, even if limited to
CONFIG_DEBUG_PER_CPU_MAPS=y case.
Link: https://syzkaller.appspot.com/bug?extid=d0fd2bf0dd6da72496dd [1]
Link: https://syzkaller.appspot.com/bug?extid=21da700f3c9f0bc40150 [2]
Link: https://syzkaller.appspot.com/bug?extid=51a652e2d24d53e75734 [3]
Link: https://lkml.kernel.org/r/20221014155845.1986223-1-ajones@ventanamicro.com [4]
Link: https://syzkaller.appspot.com/bug?extid=4d46c43d81c3bd155060 [5]
Reported-by: Andrew Jones <ajones@ventanamicro.com>
Reported-by: syzbot+d0fd2bf0dd6da72496dd@syzkaller.appspotmail.com
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Yury Norov <yury.norov@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When building with a RISC-V kernel with DWARF5 debug info using clang
and the GNU assembler, several instances of the following error appear:
/tmp/vgettimeofday-48aa35.s:2963: Error: non-constant .uleb128 is not supported
Dumping the .s file reveals these .uleb128 directives come from
.debug_loc and .debug_ranges:
.Ldebug_loc0:
.byte 4 # DW_LLE_offset_pair
.uleb128 .Lfunc_begin0-.Lfunc_begin0 # starting offset
.uleb128 .Ltmp1-.Lfunc_begin0 # ending offset
.byte 1 # Loc expr size
.byte 90 # DW_OP_reg10
.byte 0 # DW_LLE_end_of_list
.Ldebug_ranges0:
.byte 4 # DW_RLE_offset_pair
.uleb128 .Ltmp6-.Lfunc_begin0 # starting offset
.uleb128 .Ltmp27-.Lfunc_begin0 # ending offset
.byte 4 # DW_RLE_offset_pair
.uleb128 .Ltmp28-.Lfunc_begin0 # starting offset
.uleb128 .Ltmp30-.Lfunc_begin0 # ending offset
.byte 0 # DW_RLE_end_of_list
There is an outstanding binutils issue to support a non-constant operand
to .sleb128 and .uleb128 in GAS for RISC-V but there does not appear to
be any movement on it, due to concerns over how it would work with
linker relaxation.
To avoid these build errors, prevent DWARF5 from being selected when
using clang and an assembler that does not have support for these symbol
deltas, which can be easily checked in Kconfig with as-instr plus the
small test program from the dwz test suite from the binutils issue.
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=27215
Link: https://github.com/ClangBuiltLinux/linux/issues/1719
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Commit f110e5a250e3 ("kbuild: refactor single builds of *.ko") was wrong.
KBUILD_MODULES _is_ needed for single builds.
Otherwise, "make foo/bar/baz/" does not build module objects at all.
Fixes: f110e5a250e3 ("kbuild: refactor single builds of *.ko")
Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: David Sterba <dsterba@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab hotfix from Vlastimil Babka:
"A single fix for the common-kmalloc series, for warnings on mips and
sparc64 reported by Guenter Roeck"
* tag 'slab-for-6.1-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm/slab: use kmalloc_node() for off slab freelist_idx_t array allocation
|
|
Pull OpenRISC updates from Stafford Horne:
"I have relocated to London so not much work from me while I get
settled.
Still, OpenRISC picked up two patches in this window:
- Fix for kernel page table walking from Jann Horn
- MAINTAINER entry cleanup from Palmer Dabbelt"
* tag 'for-linus' of https://github.com/openrisc/linux:
MAINTAINERS: git://github -> https://github.com for openrisc
openrisc: Fix pagewalk usage in arch_dma_{clear, set}_uncached
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fix from Bjorn Helgaas:
"Revert the attempt to distribute spare resources to unconfigured
hotplug bridges at boot time.
This fixed some dock hot-add scenarios, but Jonathan Cameron reported
that it broke a topology with a multi-function device where one
function was a Switch Upstream Port and the other was an Endpoint"
* tag 'pci-v6.1-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: Distribute available resources for root buses, too"
|
|
After commit d6a71648dbc0 ("mm/slab: kmalloc: pass requests larger than
order-1 page to page allocator"), SLAB passes large ( > PAGE_SIZE * 2)
requests to buddy like SLUB does.
SLAB has been using kmalloc caches to allocate freelist_idx_t array for
off slab caches. But after the commit, freelist_size can be bigger than
KMALLOC_MAX_CACHE_SIZE.
Instead of using pointer to kmalloc cache, use kmalloc_node() and only
check if the kmalloc cache is off slab during calculate_slab_order().
If freelist_size > KMALLOC_MAX_CACHE_SIZE, no looping condition happens
as it allocates freelist_idx_t array directly from buddy.
Link: https://lore.kernel.org/all/20221014205818.GA1428667@roeck-us.net/
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: d6a71648dbc0 ("mm/slab: kmalloc: pass requests larger than order-1 page to page allocator")
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
Github deprecated the git:// links about a year ago, so let's move to
the https:// URLs instead.
Reported-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://github.blog/2021-09-01-improving-git-protocol-security-github/
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Change notification is a commonly supported feature by most servers,
but the current ioctl to request notification when a directory is
changed does not return the information about what changed
(even though it is returned by the server in the SMB3 change
notify response), it simply returns when there is a change.
This ioctl improves upon CIFS_IOC_NOTIFY by returning the notify
information structure which includes the name of the file(s) that
changed and why. See MS-SMB2 2.2.35 for details on the individual
filter flags and the file_notify_information structure returned.
To use this simply pass in the following (with enough space
to fit at least one file_notify_information structure)
struct __attribute__((__packed__)) smb3_notify {
uint32_t completion_filter;
bool watch_tree;
uint32_t data_len;
uint8_t data[];
} __packed;
using CIFS_IOC_NOTIFY_INFO 0xc009cf0b
or equivalently _IOWR(CIFS_IOCTL_MAGIC, 11, struct smb3_notify_info)
The ioctl will block until the server detects a change to that
directory or its subdirectories (if watch_tree is set).
Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
cifs_open and _cifsFileInfo_put also end up with lease_key uninitialized
in smb1 mounts. It is cleaner to set lease key to zero in these
places where leases are not supported (smb1 can not return lease keys
so the field was uninitialized).
Addresses-Coverity: 1514207 ("Uninitialized scalar variable")
Addresses-Coverity: 1514331 ("Uninitialized scalar variable")
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
It is cleaner to set lease key to zero in the places where leases are not
supported (smb1 can not return lease keys so the field was uninitialized).
Addresses-Coverity: 1513994 ("Uninitialized scalar variable")
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Coverity spotted that we were not initalizing Stbz1 and Stbz2 to
zero in create_sd_buf.
Addresses-Coverity: 1513848 ("Uninitialized scalar variable")
Cc: <stable@vger.kernel.org>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
