| Age | Commit message (Collapse) | Author |
|---|
|
mdiobus_free"
This reverts commit aa731872f7d33dcb8b54dad0cfb82d4e4d195d7e.
As pointed out by Ben Hutchings, this change is not correct.
mdiobus_unregister() can't be called if the bus isn't registered yet,
however this change can result in situations which cause that to
happen.
Part of the confusion here revolves around the fact that the
callers of this module control registration/unregistration,
rather than the module itself.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The chip ready check added by the commit 3ac3546e [Always wait for
the chip to be ready] does not work when the register read/write
is word swapped. This check has been added before the WORD_SWAP
register is programmed, so we need to check for swapped register
value as well.
Bit 16 is marked as RESERVED in SMSC datasheet, Steve Glendinning
<steve@shawell.net> checked with SMSC and wrote:
The chip architects have concluded we should be reading PMT_CTRL
until we see any of bits 0, 8, 16 or 24 set. Then we should read
BYTE_TEST to check the byte order is correct (as we already do).
The rationale behind this is that some of the chip variants have
word order swapping features too, so the READY bit could actually
be in any of the 4 possible locations. The architects have confirmed
that if any of these 4 positions is set the chip is ready. The other
3 locations will either never be set or can only go high after READY
does (so also indicate the device is ready).
This change will check for the READY bit at the 16th position. We do
not check the other two cases (bit 8 and 24) since the driver does not
support byte-swapped register read/write.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 175c0dff, drivers uses tasklet_kill to avoid put disabled tasklet
on the tasklet vec. But some of the drivers uses tasklet_init & tasklet_disable
in the driver init code, then tasklet_enable when it is opened. This makes
tasklet_enable on a killed tasklet and make ksoftirqd crazy then. Normally,
drivers should use tasklet_init/tasklet_kill on device open/remove, and use
tasklet_disable/tasklet_enable on device suspend/resume.
Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the latest kernel there are two things that must be done post decryption
so that the packet are forwarded.
1. Remove the mark from the packet. This will cause the packet to not match
the ipsec-policy again. However doing this causes the post-decryption check to
fail also and the packet will get dropped. (cat /proc/net/xfrm_stat).
2. Remove the sp association in the skbuff so that no policy check is done on
the packet for VTI tunnels.
Due to #2 above we must now do a security-policy check in the vti rcv path
prior to resetting the mark in the skbuff.
Signed-off-by: Saurabh Mohan <saurabh.mohan@vyatta.com>
Reported-by: Ruben Herold <ruben@puettmann.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Passing a NULL id causes a NULL pointer deference in writers such as
erst_writer and efi_pstore_write because they expect to update this id.
Pass a dummy id instead.
This avoids a cascade of oopses caused when the initial
pstore_console_write passes a null which in turn causes writes to the
console causing further oopses in subsequent pstore_console_write calls.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
'regulator/fix/supp-volt' into tmp
|
|
regulator_is_supported_voltage() should return true only if the voltage
of fixed/constant regulator is between min_uV and max_uV.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
The spi_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull power tools fixes from Len Brown:
"A pair of power tools patches -- a 3.7 regression fix plus a bug fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: graceful fail on garbage input
tools/power turbostat: Repair Segmentation fault when using -i option
|
|
Pull MIPS update from Ralf Baechle:
"To avoid unnecessary risk and work the preemption fixes are combined
with some preparatory work that isn't strictly required. So it's
really just 3 fixes:
- Get is_compat_task() to do the right thing while simplifying it.
The unnecessary complexity hid a rarely striking bug which could be
triggered by ext3/ext4 under certain circumstances.
- Resolve a preemption issue in the irqflags.h functions for kernels
built to support pre-MIPS32 / pre-MIPS64 Release 2 processors.
- Fix the interrupt number of the MIPS Malta's CBUS UART."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Malta: Fix interupt number of CBUS UART.
MIPS: Make irqflags.h functions preempt-safe for non-mipsr2 cpus
MIPS: Remove irqflags.h dependency from bitops.h
MIPS: bitops.h: Change use of 'unsigned short' to 'int'
MIPS: compat: Delete now unused TIF_32BIT.
MIPS: compat: Implement is_compat_task() by testing for 32-bit address space.
MIPS: compat: Fix use of TIF_32BIT_ADDR vs _TIF_32BIT_ADDR
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"This contains two fix patches for device_cgroup. One fixes a
regression introduced earlier in 3.7 cycle where device_cgroup could
try to dereference the NULL parent of the root cgroup. The other one
is RCU usage fix."
* 'for-3.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
device_cgroup: fix RCU usage
device_cgroup: fix unchecked cgroup parent usage
|
|
Commit bdb498c20040 "TTY: hvc_console, add tty install" took the port
refcounting out of hvc_open()/hvc_close(), but failed to remove the
kref_put() and tty_kref_put() calls in hvc_hangup() that were there to
remove the extra references that hvc_open() had taken.
The result was that doing a vhangup() when the current terminal was
a hvc_console, then closing the current terminal, would end up calling
destroy_hvc_struct() and making the port disappear entirely. This
meant that Fedora 17 systems would boot up but then not display the
login prompt on the console, and attempts to open /dev/hvc0 would
give a "No such device" error.
This fixes it by removing the extra kref_put() and tty_kref_put() calls.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The old ifdef CONFIG_BRCMFISCAN looks wrong to me and it makes more
sense when CONFIG_BRCMISCAN is used.
This patch was just compile tested by me, but not runtime tested.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
|
|
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Instead of listing explicitly all boards in the .dt_compat field of
the DT_MACHINE_START structure for Armada 370/XP, use instead a
compatible string that is common to all boards using the Armada
370/XP.
This allows to add new boards by just using a different Device Tree,
without having to modify the source code of the kernel.
Note that the name of the array containing the compatible string is
also renamed, to reflect the fact that it no longer contains the list
of all boards.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
All the Device Tree files for Armada 370 and XP SoCs and boards use
the "armada-370-xp" common compatible string, except
armada-370-xp.dtsi which was specifying "armada_370_xp".
Fix this inconsistency by making armada-370-xp.dtsi declare a
compatible string of "armada-370-xp" like everyone else.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This platform, available from Globalscale has an Armada 370. For now,
only the serial port is supported. Support for network, USB and other
peripherals will be added as drivers for them become available for
Armada 370 in mainline.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
This is 3.8 material.
Changes from original version posted by Gregory:
* Renamed .dts file to armada-370-mirabox.dts
* Change compatible string to 'globalscale,mirabox'
* Remove compatible string from armada-370-xp.c
* Removed references to MBX0001
|
|
This platform, available in Japan from PlatHome, has a dual-core
Armada XP, the MV78260. For now, only the two serial ports and the
three front LEDs are supported. Support for SMP, network, SATA, USB
and other peripherals will be added as drivers for them become
available for Armada XP in mainline.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
This is 3.8 material.
Changes since v2:
* Renamed the .dts file to armada-xp-openblocks-ax3-4.dts
* Removed the compatible string from armada-370-xp.c (which now only
lists the common SoC compatible string)
Changes since v1:
* Renamed the board to OpenBlocks AX3-4, since there is a variant
called AX3-2 which has less RAM, and no mini PCIe port. Requested
by Andrew Lunn.
* Fix the amount of memory to 3 GB. In fact, the board has 1 GB
soldered, and 2 GB in a SODIMM slot (which is therefore
removable). But as the board is delivered as is, we'll assume it
has 3 GB of memory by default.
|
|
The recent change for USB-audio disconnection race fixes introduced a
mutex deadlock again. There is a circular dependency between
chip->shutdown_rwsem and pcm->open_mutex, depicted like below, when a
device is opened during the disconnection operation:
A. snd_usb_audio_disconnect() ->
card.c::register_mutex ->
chip->shutdown_rwsem (write) ->
snd_card_disconnect() ->
pcm.c::register_mutex ->
pcm->open_mutex
B. snd_pcm_open() ->
pcm->open_mutex ->
snd_usb_pcm_open() ->
chip->shutdown_rwsem (read)
Since the chip->shutdown_rwsem protection in the case A is required
only for turning on the chip->shutdown flag and it doesn't have to be
taken for the whole operation, we can reduce its window in
snd_usb_audio_disconnect().
Reported-by: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When regulator_register fails and exits through the scrub path the
regulator_put function was called whilst holding the
regulator_list_mutex, causing deadlock.
This patch adds a private version of the regulator_put function which
can be safely called whilst holding the mutex, replacing the
aforementioned call.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
There is a precedence bug because | has higher precedence than ?:. This
code was cut and pasted and I fixed a similar bug a few days ago.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In the event of a VXLAN device being linked to a device that has a
hard_header_len greater than that of standard ethernet we could end up with
the hard_header_len not being large enough for outgoing frames. In order to
prevent this we should update the length when a lowerdev is provided.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use eXtensible and not eXtensiable in the comment on top.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When allocating the memory for i2c busses, the code checked the wrong
variable and thus never detected if there was a memory error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
I have been maintaining the i2c subsystem for 7 years now, it's about
time to let someone else take over. Just before I leave, I would like
to thank several individuals who made this possible at all:
* Greg Kroah-Hartman, for his faith in my potential subsystem
maintainer skills. Greg, I hope I met your expectations.
* Late David Brownell, for helping me convert the i2c subsystem to the
standard device driver model. Rest in peace David, we're missing you.
* Ben Dooks, for stepping in when I asked for someone to take care of
the huge flow of new i2c adapter drivers for embedded systems.
* Wolfram Sang, for joining the crew when it became clear that there
was more review work than Ben and myself could deal with.
I hope I did not forget anyone, please forgive me if I did.
Another big thank is due to Wolfram again, who quickly proposed to
take over as the main i2c subsystem maintainer. This will allow for a
smooth and fast transition.
Note that I will keep maintaining all I2C/SMBus controller drivers for
PC systems as well as a few others. I am hereby updating MAINTAINERS
accordingly. I'll also keep maintaining user-space i2c-tools.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Commit 6bd4a5d96c08dc2380f8053b1bd4f879f55cd3c9 changed the
ANDROID_ALARM_GET_TIME ioctls from IOW to IOR. While technically
correct, the _IOC_DIR bits are ignored by alarm_ioctl, so the
commit breaks a userspace ABI used by all existing Android devices
for a purely cosmetic reason. Revert it.
Cc: stable <stable@vger.kernel.org>
Cc: Dae S. Kim <dae@velatum.com>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change fixes an issue I found where VXLAN frames were fragmented when
they were up to the VXLAN MTU size. I root caused the issue to the fact that
the headroom was 4 + 20 + 8 + 8. This math doesn't appear to be correct
because we are not inserting a VLAN header, but instead a 2nd Ethernet header.
As such the math for the overhead should be 20 + 8 + 8 + 14 to account for the
extra headers that are inserted for VXLAN.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We added support for RFC 5961 in latest kernels but TCP fails
to perform exhaustive check of ACK sequence.
We can update our view of peer tsval from a frame that is
later discarded by tcp_ack()
This makes timestamps enabled sessions vulnerable to injection of
a high tsval : peers start an ACK storm, since the victim
sends a dupack each time it receives an ACK from the other peer.
As tcp_validate_incoming() is called before tcp_ack(), we should
not peform tcp_replace_ts_recent() from it, and let callers do it
at the right time.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Romain Francoise <romain@orebokech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of Huawei 3G and LTE modems implement a CDC NCM function,
including the necessary functional descriptors, but using a non
standard interface layout and class/subclass/protocol codes.
These devices can be handled by this driver with only a minor
change to the probing logic, allowing a single combined control
and data interface. This works because the devices
- include a CDC Union descriptor labelling the combined
interface as both master and slave, and
- have an alternate setting #1 for the bulk endpoints on the
combined interface.
The 3G/LTE network connection is managed by vendor specific AT
commands on a serial function in the same composite device.
Handling the managment function is out of the scope of this
driver. It will be handled by an appropriate USB serial
driver.
Reported-and-Tested-by: Olof Ermis <olof.ermis@gmail.com>
Reported-and-Tested-by: Tommy Cheng <tommy7765@yahoo.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the set_mac_address() function of qeth is invoked, qeth deletes
the old mac address first on OSA. Only if deletion returns
successfully the new mac address is set on OSA. Deletion may return
with a return value "MAC not found on OSA". In this case qeth
should continue setting the new mac address.
When the OSA cable is pulled, OSA forgets any set mac address. If
the OSA network interface acts as a slave to a bonding master
interface, bonding can invoke the set_mac_address function for
failover purposes and depends on successful setting of the new mac
address even though the old mac address could no longer be deleted.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return codes of IPA_CMD_QIPASSIST are not checked, especially the ones which
indicate that the command is not supported. As a result, the device driver
would not enable all available features on older card generations.
This patch adds proper checking and sets the bare minimum in the supported
functions flags to avoid follow-on errors.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device datasheet specifies the BUSY bit must be set when reading
or writing phy registers. This patch ensures we do that.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 73d4066055e0e2830533041f4b91df8e6e5976ff.
Martin Steigerwald reported that this change caused a hard lockup when
using USB if threadirqs are enabled. Thomas pointed out that this patch
is incorrect, and can cause problems. So revert it to get the
previously working functionality back.
Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Dell 5800 appears to be a simple rebrand of the Novatel E362.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit f79b2d0f (USB: keyspan: fix NULL-pointer dereferences and
memory leaks) had a small typo which made the driver use wrong
offsets when mapping serial port private data. This results in
in a GPF when the port is opened.
Reported-by: Richard <richjunk@pacbell.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CBUS UART's interrupt number was wrong conflicting with the interrupt
being tied to the Intel PIIX4. Since the PIIX4's interrupt is registered
before the CBUS UART which is not being used on most systems this would
not be noticed.
Attempts to open the ttyS2 CBUS UART would result in:
genirq: Flags mismatch irq 18. 00000000 (serial) vs. 00010000 (XT-PIC cascade)
serial_link_irq_chain: request failed: -16 for irq: 18
Qemu was written to match the kernel so will need to be fixed also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
There are laptops out there that need the eDP bpc from VBT. This is
effectively a revert of
commit 4344b813f105a19f793f1fd93ad775b784648b95
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Aug 10 11:10:20 2012 +0200
drm/i915: ignore eDP bpc settings from vbt
but putting the VBT check after the EDID check to see them both in dmesg if
this clamps more than the EDID. We have enough history with bpc clamping to
warrant the extra debug info.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47641
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56401
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Select HAVE_ALIGNED_STRUCT_PAGE on s390, so that the slub allocator can make
use of compare and swap double for lockless updates. This increases the size
of struct page to 64 bytes (instead of 56 bytes), however the performance gain
justifies the increased size:
- now excactly four struct pages fit into a single cache line; the
case that accessing a struct page causes two cache line loads
does not exist anymore.
- calculating the offset of a struct page within the memmap array
is only a simple shift instead of a more expensive multiplication.
A "hackbench 200 process 200" run on a 32 cpu system did show an 8% runtime
improvement.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
access_ok() returns always "true" on s390. Therefore all access_ok()
invocations are rather pointless.
However when walking page tables we need to make sure that everything
is within bounds of the ASCE limit of the task's address space.
So remove the access_ok() call and add the same check we have in
get_user_pages_fast().
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When walking page tables we need to make sure that everything
is within bounds of the ASCE limit of the task's address space.
Otherwise we might calculate e.g. a pud pointer which is not
within a pud and dereference it.
So check against TASK_SIZE (which is the ASCE limit) before
walking page tables.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
I don't think this works as intended. '|' higher precedence than ?: so
the bitwize OR "0 | (val & STR_MOST)" is a no-op.
I have re-written it to be more clear.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.7
A few small fixes plus a large but simple change for WM5102 which writes
out a bunch of register updates to the device when we enable the clock
as recommended following chip evaluation.
|
|
'fix/samsung' and 'fix/wm8978' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into tmp
|
|
Pull KVM fix from Marcelo Tosatti:
"A correction for user triggerable oops"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: invalid opcode oops on SET_SREGS with OSXSAVE bit set (CVE-2012-4461)
|
