summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2022-05-02drm: bridge: adv7511: use non-legacy mode for CEC RXAlvin Šipraga
The ADV7511 family of bridges supports two modes for CEC RX: legacy and non-legacy mode. The only difference is whether the chip uses a single CEC RX buffer, or uses all three available RX buffers. Currently the adv7511 driver uses legacy mode. While debugging a stall in CEC RX on an ADV7535, we reached out to Analog Devices, who suggested to use non-legacy mode instead. According to the programming guide for the ADV7511 [1], and the register control manual of the ADV7535 [2], this is the default behaviour on reset. As previously stated, the adv7511 driver currently overrides this to legacy mode. This patch updates the adv7511 driver to instead use non-legacy mode with all three CEC RX buffers. As a result of this change, we no longer experience any stalling of CEC RX with the ADV7535. It is not known why non-legacy mode solves this particular issue, but besides this, no functional change is to be expected by this patch. Please note that this has only been tested on an ADV7535. What follows is a brief description of the non-legacy mode interrupt handling behaviour. The programming guide in [1] gives a more detailed explanation. With three RX buffers, the interrupt handler checks the CEC_RX_STATUS register (renamed from CEC_RX_ENABLE in this patch), which contains 2-bit psuedo-timestamps for each of the RX buffers. The RX timestamps for each buffer represent the time of arrival for the CEC frame held in a given buffer, with lower timestamp values indicating chronologically older frames. A special value of 0 indicates that the given RX buffer is inactive and should be skipped. The interrupt handler parses these timestamps and then reads the active RX buffers in the prescribed order using the same logic as before. Changes have been made to ensure that the correct RX buffer is cleared after processing. This clearing procesure also sets the timestamp of the given RX buffer to 0 to mark it as inactive. [1] https://www.analog.com/media/en/technical-documentation/user-guides/ADV7511_Programming_Guide.pdf cf. CEC Map, register 0x4A, bit 3, default value 1: 0 = Use only buffer 0 to store CEC frames (Legacy mode) 1 = Use all 3 buffers to stores the CEC frames (Non-legacy mode) [2] The ADV7535 register control manual is under NDA, but trust me when I say that non-legacy CEC RX mode is the default here too. Here the register is offset by 0x70 and has an address of 0xBA in the DSI_CEC regiser map. Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220423120854.1503163-3-alvin@pqrs.dk
2022-05-02drm: bridge: adv7511: enable CEC support for ADV7535Alvin Šipraga
Like the ADV7533, the ADV7535 has an offset for the CEC register map, and it is the same value (ADV7533_REG_CEC_OFFSET = 0x70). Rather than testing for numerous chip types in the offset calculations throughout the driver, just compute it during driver probe and put it in the private adv7511 data structure. Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220423120854.1503163-2-alvin@pqrs.dk
2022-05-02drm/bridge: it6505: Send DPCD SET_POWER to downstreamPin-Yen Lin
Send DPCD SET_POWER command to downstream in .atomic_disable to make the downstream monitor enter the power down mode, so the device suspend won't be affected. Fixes: b5c84a9edcd418 ("drm/bridge: add it6505 driver") Signed-off-by: Pin-Yen Lin <treapking@chromium.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220425134424.1150965-1-treapking@chromium.org Reviewed-by: Robert Foss <robert.foss@linaro.org>
2022-05-02drm/panel: panel-simple: Fix proper bpc for AM-1280800N3TZQW-T00HJagan Teki
AM-1280800N3TZQW-T00H panel support 8 bpc not 6 bpc as per recent testing in i.MX8MM platform. Fix it. Fixes: bca684e69c4c ("drm/panel: simple: Add AM-1280800N3TZQW-T00H") Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20211111094103.494831-1-jagan@amarulasolutions.com
2022-05-02drm/nouveau: use drm_gem_plane_helper_prepare_fbChristian König
Instead of manually adjusting the plane state. Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220429134230.24334-3-christian.koenig@amd.com
2022-05-02drm: handle kernel fences in drm_gem_plane_helper_prepare_fb v2Christian König
drm_gem_plane_helper_prepare_fb() was using drm_atomic_set_fence_for_plane() which ignores all implicit fences when an explicit fence is already set. That's rather unfortunate when the fb still has a kernel fence we need to wait for to avoid presenting garbage on the screen. So instead update the fence in the plane state directly. While at it also take care of all potential GEM objects and not just the first one. Also remove the now unused drm_atomic_set_fence_for_plane() function, new drivers should probably use the atomic helpers directly. v2: improve kerneldoc, use local variable and num_planes, WARN_ON_ONCE on missing planes. Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1) Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220429134230.24334-1-christian.koenig@amd.com
2022-05-01Linux 5.18-rc5v5.18-rc5Linus Torvalds
2022-05-01Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds
Pull kvm fixes from Paolo Bonzini: "ARM: - Take care of faults occuring between the PARange and IPA range by injecting an exception - Fix S2 faults taken from a host EL0 in protected mode - Work around Oops caused by a PMU access from a 32bit guest when PMU has been created. This is a temporary bodge until we fix it for good. x86: - Fix potential races when walking host page table - Fix shadow page table leak when KVM runs nested - Work around bug in userspace when KVM synthesizes leaf 0x80000021 on older (pre-EPYC) or Intel processors Generic (but affects only RISC-V): - Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: work around QEMU issue with synthetic CPUID leaves Revert "x86/mm: Introduce lookup_address_in_mm()" KVM: x86/mmu: fix potential races when walking host page table KVM: fix bad user ABI for KVM_EXIT_SYSTEM_EVENT KVM: x86/mmu: Do not create SPTEs for GFNs that exceed host.MAXPHYADDR KVM: arm64: Inject exception on out-of-IPA-range translation fault KVM/arm64: Don't emulate a PMU for 32-bit guests if feature not set KVM: arm64: Handle host stage-2 faults from 32-bit EL0
2022-05-01Merge tag 'x86_urgent_for_v5.18_rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Borislav Petkov: - A fix to disable PCI/MSI[-X] masking for XEN_HVM guests as that is solely controlled by the hypervisor - A build fix to make the function prototype (__warn()) as visible as the definition itself - A bunch of objtool annotation fixes which have accumulated over time - An ORC unwinder fix to handle bad input gracefully - Well, we thought the microcode gets loaded in time in order to restore the microcode-emulated MSRs but we thought wrong. So there's a fix for that to have the ordering done properly - Add new Intel model numbers - A spelling fix * tag 'x86_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/pci/xen: Disable PCI/MSI[-X] masking for XEN_HVM guests bug: Have __warn() prototype defined unconditionally x86/Kconfig: fix the spelling of 'becoming' in X86_KERNEL_IBT config objtool: Use offstr() to print address of missing ENDBR objtool: Print data address for "!ENDBR" data warnings x86/xen: Add ANNOTATE_NOENDBR to startup_xen() x86/uaccess: Add ENDBR to __put_user_nocheck*() x86/retpoline: Add ANNOTATE_NOENDBR for retpolines x86/static_call: Add ANNOTATE_NOENDBR to static call trampoline objtool: Enable unreachable warnings for CLANG LTO x86,objtool: Explicitly mark idtentry_body()s tail REACHABLE x86,objtool: Mark cpu_startup_entry() __noreturn x86,xen,objtool: Add UNWIND hint lib/strn*,objtool: Enforce user_access_begin() rules MAINTAINERS: Add x86 unwinding entry x86/unwind/orc: Recheck address range after stack info was updated x86/cpu: Load microcode during restore_processor_state() x86/cpu: Add new Alderlake and Raptorlake CPU model numbers
2022-05-01Merge tag 'objtool_urgent_for_v5.18_rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull objtool fixes from Borislav Petkov: "A bunch of objtool fixes to improve unwinding, sibling call detection, fallthrough detection and relocation handling of weak symbols when the toolchain strips section symbols" * tag 'objtool_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: objtool: Fix code relocs vs weak symbols objtool: Fix type of reloc::addend objtool: Fix function fallthrough detection for vmlinux objtool: Fix sibling call detection in alternatives objtool: Don't set 'jump_dest' for sibling calls x86/uaccess: Don't jump between functions
2022-05-01Merge tag 'irq_urgent_for_v5.18_rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq fix from Borislav Petkov: - Fix locking when accessing device MSI descriptors * tag 'irq_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: bus: fsl-mc-msi: Fix MSI descriptor mutex lock for msi_first_desc()
2022-04-30Merge tag 'driver-core-5.18-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core fixes from Greg KH: "Here are some small driver core and kernfs fixes for some reported problems. They include: - kernfs regression that is causing oopses in 5.17 and newer releases - topology sysfs fixes for a few small reported problems. All of these have been in linux-next for a while with no reported issues" * tag 'driver-core-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: kernfs: fix NULL dereferencing in kernfs_remove topology: Fix up build warning in topology_is_visible() arch_topology: Do not set llc_sibling if llc_id is invalid topology: make core_mask include at least cluster_siblings topology/sysfs: Hide PPIN on systems that do not support it.
2022-04-30Merge tag 'char-misc-5.18-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver fixes from Greg KH: "Here are a small number of char/misc/other driver fixes for 5.18-rc5 Nothing major in here, this is mostly IIO driver fixes along with some other small things: - at25 driver fix for systems without a dma-able stack - phy driver fixes for reported issues - binder driver fixes for reported issues All of these have been in linux-next without any reported problems" * tag 'char-misc-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (31 commits) eeprom: at25: Use DMA safe buffers binder: Gracefully handle BINDER_TYPE_FDA objects with num_fds=0 binder: Address corner cases in deferred copy and fixup phy: amlogic: fix error path in phy_g12a_usb3_pcie_probe() iio: imu: inv_icm42600: Fix I2C init possible nack iio: dac: ltc2688: fix voltage scale read interconnect: qcom: sdx55: Drop IP0 interconnects interconnect: qcom: sc7180: Drop IP0 interconnects phy: ti: Add missing pm_runtime_disable() in serdes_am654_probe phy: mapphone-mdm6600: Fix PM error handling in phy_mdm6600_probe phy: ti: omap-usb2: Fix error handling in omap_usb2_enable_clocks bus: mhi: host: pci_generic: Flush recovery worker during freeze bus: mhi: host: pci_generic: Add missing poweroff() PM callback phy: ti: tusb1210: Fix an error handling path in tusb1210_probe() phy: samsung: exynos5250-sata: fix missing device put in probe error paths phy: samsung: Fix missing of_node_put() in exynos_sata_phy_probe phy: ti: Fix missing of_node_put in ti_pipe3_get_sysctrl() phy: ti: tusb1210: Make tusb1210_chg_det_states static iio:dac:ad3552r: Fix an IS_ERR() vs NULL check iio: sx9324: Fix default precharge internal resistance register ...
2022-04-30Merge tag 'tty-5.18-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial fixes from Greg KH: "Here are some small serial driver fixes, and a larger number of GSM line discipline fixes for 5.18-rc5. These include: - lots of tiny n_gsm fixes for issues to resolve a number of reported problems. Seems that people are starting to actually use this code again. - 8250 driver fixes for some devices - imx serial driver fix - amba-pl011 driver fix All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (27 commits) tty: n_gsm: fix sometimes uninitialized warning in gsm_dlci_modem_output() serial: 8250: Correct the clock for EndRun PTP/1588 PCIe device serial: 8250: Also set sticky MCR bits in console restoration tty: n_gsm: fix software flow control handling tty: n_gsm: fix invalid use of MSC in advanced option tty: n_gsm: fix broken virtual tty handling Revert "serial: sc16is7xx: Clear RS485 bits in the shutdown" tty: n_gsm: fix missing update of modem controls after DLCI open serial: 8250: Fix runtime PM for start_tx() for empty buffer serial: imx: fix overrun interrupts in DMA mode serial: amba-pl011: do not time out prematurely when draining tx fifo tty: n_gsm: fix incorrect UA handling tty: n_gsm: fix reset fifo race condition tty: n_gsm: fix missing tty wakeup in convergence layer type 2 tty: n_gsm: fix wrong signal octets encoding in MSC tty: n_gsm: fix wrong command frame length field encoding tty: n_gsm: fix wrong command retry handling tty: n_gsm: fix missing explicit ldisc flush tty: n_gsm: fix wrong DLCI release order tty: n_gsm: fix insufficient txframe size ...
2022-04-30Merge tag 'usb-5.18-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg KH: "Here are a number of small USB driver fixes for 5.18-rc5 for some reported issues and new quirks. They include: - dwc3 driver fixes - xhci driver fixes - typec driver fixes - new usb-serial driver ids - added new USB devices to existing quirk tables - other tiny fixes All of these have been in linux-next for a while with no reported issues" * tag 'usb-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (31 commits) usb: phy: generic: Get the vbus supply usb: dwc3: gadget: Return proper request status usb: dwc3: pci: add support for the Intel Meteor Lake-P usb: dwc3: core: Only handle soft-reset in DCTL usb: gadget: configfs: clear deactivation flag in configfs_composite_unbind() usb: misc: eud: Fix an error handling path in eud_probe() usb: core: Don't hold the device lock while sleeping in do_proc_control() usb: dwc3: Try usb-role-switch first in dwc3_drd_init usb: dwc3: core: Fix tx/rx threshold settings usb: mtu3: fix USB 3.0 dual-role-switch from device to host xhci: Enable runtime PM on second Alderlake controller usb: dwc3: fix backwards compat with rockchip devices dt-bindings: usb: samsung,exynos-usb2: add missing required reg usb: misc: fix improper handling of refcount in uss720_probe() USB: Fix ehci infinite suspend-resume loop issue in zhaoxin usb: typec: tcpm: Fix undefined behavior due to shift overflowing the constant usb: typec: rt1719: Fix build error without CONFIG_POWER_SUPPLY usb: typec: ucsi: Fix role swapping usb: typec: ucsi: Fix reuse of completion structure usb: xhci: tegra:Fix PM usage reference leak of tegra_xusb_unpowergate_partitions ...
2022-04-30Merge tag 'scsi-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fix from James Bottomley: "One fix for an endless error loop with the target driver affecting tapes" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: target: pscsi: Set SCF_TREAT_READ_AS_NORMAL flag only if there is valid data
2022-04-29Merge tag 'soc-fixes-5.18-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: - A fix for a regression caused by the previous set of bugfixes changing tegra and at91 pinctrl properties. More work is needed to figure out what this should actually be, but a revert makes it work for the moment. - Defconfig regression fixes for tegra after renamed symbols - Build-time warning and static checker fixes for imx, op-tee, sunxi, meson, at91, and omap - More at91 DT fixes for audio, regulator and spi nodes - A regression fix for Renesas Hyperflash memory probe - A stability fix for amlogic boards, modifying the allowed cpufreq states - Multiple fixes for system suspend on omap2+ - DT fixes for various i.MX bugs - A probe error fix for imx6ull-colibri MMC - A MAINTAINERS file entry for samsung bug reports * tag 'soc-fixes-5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits) Revert "arm: dts: at91: Fix boolean properties with values" bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create() Revert "arm64: dts: tegra: Fix boolean properties with values" arm64: dts: imx8mn-ddr4-evk: Describe the 32.768 kHz PMIC clock ARM: dts: imx6ull-colibri: fix vqmmc regulator MAINTAINERS: add Bug entry for Samsung and memory controller drivers memory: renesas-rpc-if: Fix HF/OSPI data transfer in Manual Mode ARM: dts: logicpd-som-lv: Fix wrong pinmuxing on OMAP35 ARM: dts: am3517-evm: Fix misc pinmuxing ARM: dts: am33xx-l4: Add missing touchscreen clock properties ARM: dts: Fix mmc order for omap3-gta04 ARM: dts: at91: fix pinctrl phandles ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name ARM: dts: at91: Describe regulators on at91sam9g20ek ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek ARM: dts: at91: Fix boolean properties with values ARM: dts: at91: use generic node name for dataflash ARM: dts: at91: align SPI NOR node name with dtschema ARM: dts: at91: sama7g5ek: Align the impedance of the QSPI0's HSIO and PCB lines ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines ...
2022-04-29Merge tag 'clk-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux Pull clk fixes from Stephen Boyd: "A semi-large pile of clk driver fixes this time around. Nothing is touching the core so these fixes are fairly well contained to specific devices that use these clk drivers. - Some Allwinner SoC fixes to gracefully handle errors and mark an RTC clk as critical so that the RTC keeps ticking. - Fix AXI bus clks and RTC clk design for Microchip PolarFire SoC driver introduced this cycle. This has some devicetree bits acked by riscv maintainers. We're fixing it now so that the prior bindings aren't released in a major kernel version. - Remove a reset on Microchip PolarFire SoCs that broke when enabling CONFIG_PM. - Set a min/max for the Qualcomm graphics clk. This got broken by the clk rate range patches introduced this cycle" * tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: clk: sunxi: sun9i-mmc: check return value after calling platform_get_resource() clk: sunxi-ng: sun6i-rtc: Mark rtc-32k as critical riscv: dts: microchip: reparent mpfs clocks clk: microchip: mpfs: add RTCREF clock control clk: microchip: mpfs: re-parent the configurable clocks dt-bindings: rtc: add refclk to mpfs-rtc dt-bindings: clk: mpfs: add defines for two new clocks dt-bindings: clk: mpfs document msspll dri registers riscv: dts: microchip: fix usage of fic clocks on mpfs clk: microchip: mpfs: mark CLK_ATHENA as critical clk: microchip: mpfs: fix parents for FIC clocks clk: qcom: clk-rcg2: fix gfx3d frequency calculation clk: microchip: mpfs: don't reset disabled peripherals clk: sunxi-ng: fix not NULL terminated coccicheck error
2022-04-29Merge tag 'block-5.18-2022-04-29' of git://git.kernel.dk/linux-blockLinus Torvalds
Pull block fixes from Jens Axboe: - Revert of a patch that caused timestamp issues (Tejun) - iocost warning fix (Tejun) - bfq warning fix (Jan) * tag 'block-5.18-2022-04-29' of git://git.kernel.dk/linux-block: bfq: Fix warning in bfqq_request_over_limit() Revert "block: inherit request start time from bio for BLK_CGROUP" iocost: don't reset the inuse weight of under-weighted debtors
2022-04-29Merge tag 'io_uring-5.18-2022-04-29' of git://git.kernel.dk/linux-blockLinus Torvalds
Pull io_uring fixes from Jens Axboe: "Pretty boring: - three patches just adding reserved field checks (me, Eugene) - Fixing a potential regression with IOPOLL caused by a block change (Joseph)" Boring is good. * tag 'io_uring-5.18-2022-04-29' of git://git.kernel.dk/linux-block: io_uring: check that data field is 0 in ringfd unregister io_uring: fix uninitialized field in rw io_kiocb io_uring: check reserved fields for recv/recvmsg io_uring: check reserved fields for send/sendmsg
2022-04-29Merge tag 'random-5.18-rc5-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random Pull random number generator fixes from Jason Donenfeld: - Eric noticed that the memmove() in crng_fast_key_erasure() was bogus, so this has been changed to a memcpy() and the confusing situation clarified with a detailed comment. - [Half]SipHash documentation updates from Bagas and Eric, after Eric pointed out that the use of HalfSipHash in random.c made a bit of the text potentially misleading. * tag 'random-5.18-rc5-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: Documentation: siphash: disambiguate HalfSipHash algorithm from hsiphash functions Documentation: siphash: enclose HalfSipHash usage example in the literal block Documentation: siphash: convert danger note to warning for HalfSipHash random: document crng_fast_key_erasure() destination possibility
2022-04-29Merge tag 'ceph-for-5.18-rc5' of https://github.com/ceph/ceph-clientLinus Torvalds
Pull ceph client fixes from Ilya Dryomov: "A fix for a NULL dereference that turns out to be easily triggerable by fsync (marked for stable) and a false positive WARN and snap_rwsem locking fixups" * tag 'ceph-for-5.18-rc5' of https://github.com/ceph/ceph-client: ceph: fix possible NULL pointer dereference for req->r_session ceph: remove incorrect session state check ceph: get snap_rwsem read lock in handle_cap_export for ceph_add_cap libceph: disambiguate cluster/pool full log message
2022-04-29drm/panel: simple: Add Startek KD070WVFPA043-C069A panel supportHeiko Schocher
Add Startek KD070WVFPA043-C069A 7" TFT LCD panel support. Signed-off-by: Heiko Schocher <hs@denx.de> [fabio: passed .flags and .bus_flags] Signed-off-by: Fabio Estevam <festevam@denx.de> Acked-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Marek Vasut <marex@denx.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220429172056.3499563-2-festevam@gmail.com
2022-04-29dt-bindings: display: simple: Add Startek KD070WVFPA043-C069A panelFabio Estevam
Add Startek KD070WVFPA043-C069A 7" TFT LCD panel compatible string. Signed-off-by: Fabio Estevam <festevam@denx.de> Acked-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Marek Vasut <marex@denx.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220429172056.3499563-1-festevam@gmail.com
2022-04-29Revert "arm: dts: at91: Fix boolean properties with values"Arnd Bergmann
This reverts commit 0dc23d1a8e17, which caused another regression as the pinctrl code actually expects an integer value of 0 or 1 rather than a simple boolean property. Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-04-29drm/nouveau: simplify the return expression of nouveau_debugfs_init()Minghao Chi
Simplify the return expression. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Reviewed-by: Lyude Paul <lyude@redhat.com> [fixed an indenting error before pushing] Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220429090309.3853003-1-chi.minghao@zte.com.cn
2022-04-29KVM: x86: work around QEMU issue with synthetic CPUID leavesPaolo Bonzini
Synthesizing AMD leaves up to 0x80000021 caused problems with QEMU, which assumes the *host* CPUID[0x80000000].EAX is higher or equal to what KVM_GET_SUPPORTED_CPUID reports. This causes QEMU to issue bogus host CPUIDs when preparing the input to KVM_SET_CPUID2. It can even get into an infinite loop, which is only terminated by an abort(): cpuid_data is full, no space for cpuid(eax:0x8000001d,ecx:0x3e) To work around this, only synthesize those leaves if 0x8000001d exists on the host. The synthetic 0x80000021 leaf is mostly useful on Zen2, which satisfies the condition. Fixes: f144c49e8c39 ("KVM: x86: synthesize CPUID leaf 0x80000021h if useful") Reported-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2022-04-29Merge tag 'perf-tools-fixes-for-v5.18-2022-04-29' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux Pull perf tools fixes from Arnaldo Carvalho de Melo: - Fix Intel PT (Processor Trace) timeless decoding with perf.data directory. - ARM SPE (Statistical Profiling Extensions) address fixes, for synthesized events and for SPE events with physical addresses. Add a simple 'perf test' entry to make sure this doesn't regress. - Remove arch specific processing of kallsyms data to fixup symbol end address, fixing excessive memory consumption in the annotation code. * tag 'perf-tools-fixes-for-v5.18-2022-04-29' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: perf symbol: Remove arch__symbols__fixup_end() perf symbol: Update symbols__fixup_end() perf symbol: Pass is_kallsyms to symbols__fixup_end() perf test: Add perf_event_attr test for Arm SPE perf arm-spe: Fix SPE events with phys addresses perf arm-spe: Fix addresses of synthesized SPE events perf intel-pt: Fix timeless decoding with perf.data directory
2022-04-29Merge tag 'riscv-for-linus-5.18-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V fixes from Palmer Dabbelt: - A fix to properly ensure a single CPU is running during patch_text(). - A defconfig update to include RPMSG_CTRL when RPMSG_CHAR was set, necessary after a recent refactoring. * tag 'riscv-for-linus-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: RISC-V: configs: Configs that had RPMSG_CHAR now get RPMSG_CTRL riscv: patch_text: Fixup last cpu should be master
2022-04-29Merge tag 'arm64-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fix from Will Deacon: "Rename and reallocate the PT_ARM_MEMTAG_MTE ELF segment type. This is a fix to the MTE ELF ABI for a bug that was added during the most recent merge window as part of the coredump support. The issue is that the value assigned to the new PT_ARM_MEMTAG_MTE segment type has already been allocated to PT_AARCH64_UNWIND by the ELF ABI, so we've bumped the value and changed the name of the identifier to be better aligned with the existing one" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: elf: Fix the arm64 MTE ELF segment name and value
2022-04-29Revert "x86/mm: Introduce lookup_address_in_mm()"Sean Christopherson
Drop lookup_address_in_mm() now that KVM is providing it's own variant of lookup_address_in_pgd() that is safe for use with user addresses, e.g. guards against page tables being torn down. A variant that provides a non-init mm is inherently dangerous and flawed, as the only reason to use an mm other than init_mm is to walk a userspace mapping, and lookup_address_in_pgd() does not play nice with userspace mappings, e.g. doesn't disable IRQs to block TLB shootdowns and doesn't use READ_ONCE() to ensure an upper level entry isn't converted to a huge page between checking the PAGE_SIZE bit and grabbing the address of the next level down. This reverts commit 13c72c060f1ba6f4eddd7b1c4f52a8aded43d6d9. Signed-off-by: Sean Christopherson <seanjc@google.com> Message-Id: <YmwIi3bXr/1yhYV/@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2022-04-29Merge branch 'kvm-fixes-for-5.18-rc5' into HEADPaolo Bonzini
Fixes for (relatively) old bugs, to be merged in both the -rc and next development trees: * Fix potential races when walking host page table * Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT * Fix shadow page table leak when KVM runs nested
2022-04-29KVM: x86/mmu: fix potential races when walking host page tableMingwei Zhang
KVM uses lookup_address_in_mm() to detect the hugepage size that the host uses to map a pfn. The function suffers from several issues: - no usage of READ_ONCE(*). This allows multiple dereference of the same page table entry. The TOCTOU problem because of that may cause KVM to incorrectly treat a newly generated leaf entry as a nonleaf one, and dereference the content by using its pfn value. - the information returned does not match what KVM needs; for non-present entries it returns the level at which the walk was terminated, as long as the entry is not 'none'. KVM needs level information of only 'present' entries, otherwise it may regard a non-present PXE entry as a present large page mapping. - the function is not safe for mappings that can be torn down, because it does not disable IRQs and because it returns a PTE pointer which is never safe to dereference after the function returns. So implement the logic for walking host page tables directly in KVM, and stop using lookup_address_in_mm(). Cc: Sean Christopherson <seanjc@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Mingwei Zhang <mizhang@google.com> Message-Id: <20220429031757.2042406-1-mizhang@google.com> [Inline in host_pfn_mapping_level, ensure no semantic change for its callers. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2022-04-29KVM: fix bad user ABI for KVM_EXIT_SYSTEM_EVENTPaolo Bonzini
When KVM_EXIT_SYSTEM_EVENT was introduced, it included a flags member that at the time was unused. Unfortunately this extensibility mechanism has several issues: - x86 is not writing the member, so it would not be possible to use it on x86 except for new events - the member is not aligned to 64 bits, so the definition of the uAPI struct is incorrect for 32- on 64-bit userspace. This is a problem for RISC-V, which supports CONFIG_KVM_COMPAT, but fortunately usage of flags was only introduced in 5.18. Since padding has to be introduced, place a new field in there that tells if the flags field is valid. To allow further extensibility, in fact, change flags to an array of 16 values, and store how many of the values are valid. The availability of the new ndata field is tied to a system capability; all architectures are changed to fill in the field. To avoid breaking compilation of userspace that was using the flags field, provide a userspace-only union to overlap flags with data[0]. The new field is placed at the same offset for both 32- and 64-bit userspace. Cc: Will Deacon <will@kernel.org> Cc: Marc Zyngier <maz@kernel.org> Cc: Peter Gonda <pgonda@google.com> Cc: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reported-by: kernel test robot <lkp@intel.com> Message-Id: <20220422103013.34832-1-pbonzini@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2022-04-29KVM: x86/mmu: Do not create SPTEs for GFNs that exceed host.MAXPHYADDRSean Christopherson
Disallow memslots and MMIO SPTEs whose gpa range would exceed the host's MAXPHYADDR, i.e. don't create SPTEs for gfns that exceed host.MAXPHYADDR. The TDP MMU bounds its zapping based on host.MAXPHYADDR, and so if the guest, possibly with help from userspace, manages to coerce KVM into creating a SPTE for an "impossible" gfn, KVM will leak the associated shadow pages (page tables): WARNING: CPU: 10 PID: 1122 at arch/x86/kvm/mmu/tdp_mmu.c:57 kvm_mmu_uninit_tdp_mmu+0x4b/0x60 [kvm] Modules linked in: kvm_intel kvm irqbypass CPU: 10 PID: 1122 Comm: set_memory_regi Tainted: G W 5.18.0-rc1+ #293 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 RIP: 0010:kvm_mmu_uninit_tdp_mmu+0x4b/0x60 [kvm] Call Trace: <TASK> kvm_arch_destroy_vm+0x130/0x1b0 [kvm] kvm_destroy_vm+0x162/0x2d0 [kvm] kvm_vm_release+0x1d/0x30 [kvm] __fput+0x82/0x240 task_work_run+0x5b/0x90 exit_to_user_mode_prepare+0xd2/0xe0 syscall_exit_to_user_mode+0x1d/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xae </TASK> On bare metal, encountering an impossible gpa in the page fault path is well and truly impossible, barring CPU bugs, as the CPU will signal #PF during the gva=>gpa translation (or a similar failure when stuffing a physical address into e.g. the VMCS/VMCB). But if KVM is running as a VM itself, the MAXPHYADDR enumerated to KVM may not be the actual MAXPHYADDR of the underlying hardware, in which case the hardware will not fault on the illegal-from-KVM's-perspective gpa. Alternatively, KVM could continue allowing the dodgy behavior and simply zap the max possible range. But, for hosts with MAXPHYADDR < 52, that's a (minor) waste of cycles, and more importantly, KVM can't reasonably support impossible memslots when running on bare metal (or with an accurate MAXPHYADDR as a VM). Note, limiting the overhead by checking if KVM is running as a guest is not a safe option as the host isn't required to announce itself to the guest in any way, e.g. doesn't need to set the HYPERVISOR CPUID bit. A second alternative to disallowing the memslot behavior would be to disallow creating a VM with guest.MAXPHYADDR > host.MAXPHYADDR. That restriction is undesirable as there are legitimate use cases for doing so, e.g. using the highest host.MAXPHYADDR out of a pool of heterogeneous systems so that VMs can be migrated between hosts with different MAXPHYADDRs without running afoul of the allow_smaller_maxphyaddr mess. Note that any guest.MAXPHYADDR is valid with shadow paging, and it is even useful in order to test KVM with MAXPHYADDR=52 (i.e. without any reserved physical address bits). The now common kvm_mmu_max_gfn() is inclusive instead of exclusive. The memslot and TDP MMU code want an exclusive value, but the name implies the returned value is inclusive, and the MMIO path needs an inclusive check. Fixes: faaf05b00aec ("kvm: x86/mmu: Support zapping SPTEs in the TDP MMU") Fixes: 524a1e4e381f ("KVM: x86/mmu: Don't leak non-leaf SPTEs when zapping all SPTEs") Cc: stable@vger.kernel.org Cc: Maxim Levitsky <mlevitsk@redhat.com> Cc: Ben Gardon <bgardon@google.com> Cc: David Matlack <dmatlack@google.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Message-Id: <20220428233416.2446833-1-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2022-04-29Merge tag 'kvmarm-fixes-5.18-2' of ↵Paolo Bonzini
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD KVM/arm64 fixes for 5.18, take #2 - Take care of faults occuring between the PARange and IPA range by injecting an exception - Fix S2 faults taken from a host EL0 in protected mode - Work around Oops caused by a PMU access from a 32bit guest when PMU has been created. This is a temporary bodge until we fix it for good.
2022-04-29Merge tag 'tegra-for-5.18-arm-defconfig-fixes' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes ARM: tegra: Default configuration fixes for v5.18 This contains two updates to the default configuration needed because of a Kconfig symbol name change. This fixes a failure that was detected in the NVIDIA automated test farm. * tag 'tegra-for-5.18-arm-defconfig-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: ARM: config: multi v7: Enable NVIDIA Tegra video decoder driver ARM: tegra_defconfig: Update CONFIG_TEGRA_VDE option Link: https://lore.kernel.org/r/20220429080626.494150-1-thierry.reding@gmail.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-04-29io_uring: check that data field is 0 in ringfd unregisterEugene Syromiatnikov
Only allow data field to be 0 in struct io_uring_rsrc_update user arguments to allow for future possible usage. Fixes: e7a6c00dc77a ("io_uring: add support for registering ring file descriptors") Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com> Link: https://lore.kernel.org/r/20220429142218.GA28696@asgard.redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
2022-04-29drm/vc4: simplify the return expression of vc4_grab_bin_bo()Minghao Chi
Simplify the return expression. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220429090208.3852879-1-chi.minghao@zte.com.cn
2022-04-29drm/vc4: simplify the return expression of vc4_prepare_fb()Minghao Chi
Simplify the return expression. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220429054945.3852039-1-chi.minghao@zte.com.cn
2022-04-29drm/sun4i: dsi: delete unnecessary IS_ERR() checksDan Carpenter
The "dsi->bus_clk" pointer cannot be an error pointer at this point. The check is confusing and unnecessary. Delete it. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/YmqH71MtoGn2AXUg@kili
2022-04-29Merge tag 'imx-fixes-5.18-2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 5.18, 2nd round: - Fix one sparse warning on imx-weim driver. - Fix vqmmc regulator to get UHS-I mode work on imx6ull-colibri board. - Add missing 32.768 kHz PMIC clock for imx8mn-ddr4-evk board to fix bd718xx-clk probe error. * tag 'imx-fixes-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: arm64: dts: imx8mn-ddr4-evk: Describe the 32.768 kHz PMIC clock ARM: dts: imx6ull-colibri: fix vqmmc regulator bus: imx-weim: make symbol 'weim_of_notifier' static Link: https://lore.kernel.org/r/20220426013427.GB14615@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-04-29Merge tag 'sunxi-fixes-for-5.18-1' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes Fix return value in RSB bus driver * tag 'sunxi-fixes-for-5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create() Link: https://lore.kernel.org/r/Ymbkd+/dDmRJz66w@kista.localdomain Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-04-29drm/bridge: tc358767: Fix (e)DP bridge endpoint parsing in dedicated functionMarek Vasut
Per toshiba,tc358767.yaml DT binding document, port@2 the output (e)DP port is optional. In case this port is not described in DT, the bridge driver operates in DPI-to-DP mode. The drm_of_find_panel_or_bridge() call in tc_probe_edp_bridge_endpoint() returns -ENODEV in case port@2 is not present in DT and this specific return value is incorrectly propagated outside of tc_probe_edp_bridge_endpoint() function. All other error values must be propagated and are propagated correctly. Return 0 in case the port@2 is missing instead, that reinstates the original behavior before the commit this patch fixes. Fixes: 8478095a8c4b ("drm/bridge: tc358767: Move (e)DP bridge endpoint parsing into dedicated function") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Marek Vasut <marex@denx.de> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220428213132.447890-1-marex@denx.de
2022-04-29bfq: Fix warning in bfqq_request_over_limit()Jan Kara
People are occasionally reporting a warning bfqq_request_over_limit() triggering reporting that BFQ's idea of cgroup hierarchy (and its depth) does not match what generic blkcg code thinks. This can actually happen when bfqq gets moved between BFQ groups while bfqq_request_over_limit() is running. Make sure the code is safe against BFQ queue being moved to a different BFQ group. Fixes: 76f1df88bbc2 ("bfq: Limit number of requests consumed by each cgroup") CC: stable@vger.kernel.org Link: https://lore.kernel.org/all/CAJCQCtTw_2C7ZSz7as5Gvq=OmnDiio=HRkQekqWpKot84sQhFA@mail.gmail.com/ Reported-by: Chris Murphy <lists@colorremedies.com> Reported-by: "yukuai (C)" <yukuai3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220407140738.9723-1-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk>
2022-04-29x86/pci/xen: Disable PCI/MSI[-X] masking for XEN_HVM guestsThomas Gleixner
When a XEN_HVM guest uses the XEN PIRQ/Eventchannel mechanism, then PCI/MSI[-X] masking is solely controlled by the hypervisor, but contrary to XEN_PV guests this does not disable PCI/MSI[-X] masking in the PCI/MSI layer. This can lead to a situation where the PCI/MSI layer masks an MSI[-X] interrupt and the hypervisor grants the write despite the fact that it already requested the interrupt. As a consequence interrupt delivery on the affected device is not happening ever. Set pci_msi_ignore_mask to prevent that like it's done for XEN_PV guests already. Fixes: 809f9267bbab ("xen: map MSIs into pirqs") Reported-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com> Reported-by: Dusty Mabe <dustymabe@redhat.com> Reported-by: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Noah Meyerhans <noahm@debian.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/87tuaduxj5.ffs@tglx
2022-04-29drm/edid: drop kernel-doc for static functionsJani Nikula
Drop the kernel-doc for static functions, it's excessive, but retain the info in plain comments. Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Simon Ser <contact@emersion.fr> Link: https://patchwork.freedesktop.org/patch/msgid/20220426091913.1339941-2-jani.nikula@intel.com
2022-04-29drm/edid: fix kernel-doc parameter name mismatchesJani Nikula
Fix the below drm/edid kernel-doc warnings: drivers/gpu/drm/drm_edid.c:1589: warning: Function parameter or member '_edid' not described in 'drm_edid_header_is_valid' drivers/gpu/drm/drm_edid.c:1589: warning: Excess function parameter 'raw_edid' description in 'drm_edid_header_is_valid' drivers/gpu/drm/drm_edid.c:1737: warning: Function parameter or member '_block' not described in 'drm_edid_block_valid' drivers/gpu/drm/drm_edid.c:1737: warning: Excess function parameter 'raw_edid' description in 'drm_edid_block_valid' drivers/gpu/drm/drm_edid.c:2136: warning: Function parameter or member 'read_block' not described in 'drm_do_get_edid' drivers/gpu/drm/drm_edid.c:2136: warning: Function parameter or member 'context' not described in 'drm_do_get_edid' drivers/gpu/drm/drm_edid.c:2136: warning: Excess function parameter 'get_edid_block' description in 'drm_do_get_edid' drivers/gpu/drm/drm_edid.c:2136: warning: Excess function parameter 'data' description in 'drm_do_get_edid' Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> References: https://lore.kernel.org/r/20220406154431.567414c3@canb.auug.org.au References: https://lore.kernel.org/r/20220420162431.2b28ddea@canb.auug.org.au Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Simon Ser <contact@emersion.fr> Link: https://patchwork.freedesktop.org/patch/msgid/20220426091913.1339941-1-jani.nikula@intel.com
2022-04-29drm/display: Select DP helper for DRM_DP_AUX_CHARDEV and DRM_DP_CECJavier Martinez Canillas
The DRM_DP_AUX_CHARDEV and DRM_DP_CEC Kconfig symbols enable code that use DP helper functions, that are only present if CONFIG_DRM_DISPLAY_DP_HELPER is also enabled. But these don't select the DRM_DISPLAY_DP_HELPER symbol, meaning that it is possible to enable any of them without CONFIG_DRM_DISPLAY_DP_HELPER. That will lead to the following linking errors with the mentioned config: LD vmlinux.o MODPOST vmlinux.symvers MODINFO modules.builtin.modinfo GEN modules.builtin LD .tmp_vmlinux.kallsyms1 KSYMS .tmp_vmlinux.kallsyms1.S AS .tmp_vmlinux.kallsyms1.S LD .tmp_vmlinux.kallsyms2 KSYMS .tmp_vmlinux.kallsyms2.S AS .tmp_vmlinux.kallsyms2.S LD vmlinux SYSMAP System.map SORTTAB vmlinux OBJCOPY arch/arm64/boot/Image MODPOST modules-only.symvers ERROR: modpost: "drm_dp_dpcd_write" [drivers/gpu/drm/display/drm_display_helper.ko] undefined! ERROR: modpost: "drm_dp_read_desc" [drivers/gpu/drm/display/drm_display_helper.ko] undefined! ERROR: modpost: "drm_dp_dpcd_read" [drivers/gpu/drm/display/drm_display_helper.ko] undefined! make[1]: *** [scripts/Makefile.modpost:134: modules-only.symvers] Error 1 make[1]: *** Deleting file 'modules-only.symvers' make: *** [Makefile:1749: modules] Error 2 Besides making these symbols to select CONFIG_DRM_DISPLAY_DP_HELPER, make them to depend on DRM_DISPLAY_HELPER, since can't be enabled without it. Note: It seems this has been an issue for a long time but was made easier to reproduce after the commit 1e0f66420b13 ("drm/display: Introduce a DRM display-helper module"). Adding a Fixes: tag just to make sure that this fix will be picked for stable once the mentioned change also lands there. Fixes: 1e0f66420b13 ("drm/display: Introduce a DRM display-helper module") Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220428082244.390859-1-javierm@redhat.com
2022-04-29Merge tag 'drm-misc-next-2022-04-28' of ↵Dave Airlie
git://anongit.freedesktop.org/drm/drm-misc into drm-next drm-misc-next for 5.19: UAPI Changes: Cross-subsystem Changes: Core Changes: - Introduction of display-helper module, and rework of the DP, DSC, HDCP, HDMI and SCDC headers - doc: Improvements for tiny drivers, link to external resources - formats: helper to convert from RGB888 and RGB565 to XRGB8888 - modes: make width-mm/height-mm check mandatory in of_get_drm_panel_display_mode - ttm: Convert from kvmalloc_array to kvcalloc Driver Changes: - bridge: - analogix_dp: Fix error handling in probe - dw_hdmi: Coccinelle fixes - it6505: Fix Kconfig dependency on DRM_DP_AUX_BUS - panel: - new panel: DataImage FG040346DSSWBG04 - amdgpu: ttm_eu cleanups - mxsfb: Rework CRTC mode setting - nouveau: Make some variables static - sun4i: Drop drm_display_info.is_hdmi caching, support for the Allwinner D1 - vc4: Drop drm_display_info.is_hdmi caching - vmwgfx: Fence improvements Signed-off-by: Dave Airlie <airlied@redhat.com> # gpg: Signature made Thu 28 Apr 2022 17:52:13 AEST # gpg: using EDDSA key 5C1337A45ECA9AEB89060E9EE3EF0D6F671851C5 # gpg: Can't check signature: No public key From: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220428075237.yypztjha7hetphcd@houat
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-30 13:31:30 +0000