| Age | Commit message (Collapse) | Author |
|---|
|
Due to the tight timing constraints in some UHS modes, it is required to have
some delay management in the design. Two types of delay management are supported
in the HW: -
1) Static delay management
2) Dynamic delay management
NB: The delay management is only there when eMMC interface is selected.
1: Static delay management: is used to provide PVT dependent static delay on the
clock/data lines to manage setup/hold requirements of the interface. The maximum
delay possible is 3.25ns. These delays are PVT dependent, and thus delay values
applied are not accurate and vary across provcess voltage and temperature range.
Due to this these delays must not be used on the very time critical paths.
2. Dynamic delay locked loop (DLL): is used to provide dynamic delay management.
The advantage of DLL is that it provides accurate & PVT indepedent delay.
The DLL is used to provide delay on the loopback clock on "Read Path" to capture
read data reliably. On TX path the clock on which output data is transmitted is
delayed, resulting in delay of TX data.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
STiH407 family SoC's can have a reset signal for the controller which needs to
be managed. Also the eMMC controller has some additional 'top' memory mapped
registers which are used to manage the dynamic and static delay required for
UHS modes. This patch adds support for creating the mapping, which will be used
by subsequent patches.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The stih407 family SoC's have additional glue registers in the flashSS which
are used to configure the Arasan controller.
This patch adds macros for the register offsets and bitfields which will be
used by subsequent patches to support stih407 family SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Update the check for UV2000/3000. Note when the HUB is not recognized.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Hedi Berriche <hedi@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/20150409182629.267239403@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix a bug in the OEM check function that determines if the
system is a UV system and the BIOS is compatible with the
kernel's UV apic driver. This prevents some possibly obscure
panics and guards the system against being started on SGI
hardware that does not have the required kernel support.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Hedi Berriche <hedi@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/20150409182629.112998930@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Optimize the first "SGI" OEM check to return faster if the
system is not an SGI or UV system.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Hedi Berriche <hedi@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/20150409182628.952357922@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since commit 20d0189b1012a37d2533a87fb451f7852f2418d1
in v3.14-rc1 RAID0 has performed incorrect calculations
when the chunksize is not a power of 2.
This happens because "sector_div()" modifies its first argument, but
this wasn't taken into account in the patch.
So restore that first arg before re-using the variable.
Reported-by: Joe Landman <joe.landman@gmail.com>
Reported-by: Dave Chinner <david@fromorbit.com>
Fixes: 20d0189b1012a37d2533a87fb451f7852f2418d1
Cc: stable@vger.kernel.org (3.14 and later).
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Remove the end address checking for flushda function. We need to flush
each address line for flushda instruction, from start to end address.
This is because flushda instruction only flush the cache if tag and line
fields are matched.
Change to use ldwio instruction (bypass cache) to load the instruction
that causing trap. Our interest is the actual instruction that executed
by the processor, this should be uncached.
Note, EA address might be an userspace cached address.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are stable-candidate fixes of some recently reported issues in
the cpufreq core, cpuidle core, the ACPI cpuidle driver and the
hibernate core.
Specifics:
- Revert a 3.17 hibernate commit that was supposed to fix an issue
related to e820 reserved regions, but broke resume from hibernation
on Lenovo x230 (Rafael J Wysocki).
- Prevent the ACPI cpuidle driver from overwriting the name and
description of the C0 state set by the core when the list of
C-states changes (Thomas Schlichter).
- Remove the no longer needed state_count field from struct
cpuidle_device which prevents the list of C-states shown by the
sysfs interface from becoming incorrect when the current number of
them is different from the number of C-states on boot (Bartlomiej
Zolnierkiewicz).
- The cpufreq core updates the policy object of the only online CPU
during system resume to make it reflect the current hardware state,
but it always assumes that CPU to be CPU0 which need not be the
case, so fix the code to avoid that assumption (Viresh Kumar)"
* tag 'pm+acpi-4.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / hibernate: avoid unsafe pages in e820 reserved regions"
cpuidle: ACPI: do not overwrite name and description of C0
cpuidle: remove state_count field from struct cpuidle_device
cpufreq: Schedule work for the first-online CPU on resume
|
|
Reading both the capability ID and "next" pointer at the same time lets us
parse the list with half the number of config reads.
Signed-off-by: Sean O. Stalley <sean.stalley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
* pm-sleep:
Revert "PM / hibernate: avoid unsafe pages in e820 reserved regions"
* pm-cpufreq:
cpufreq: Schedule work for the first-online CPU on resume
* pm-cpuidle:
cpuidle: ACPI: do not overwrite name and description of C0
cpuidle: remove state_count field from struct cpuidle_device
|
|
devm_ioremap_resource() validates the resource it receives, so if we check
for devm_ioremap_resource() failure, we need not check for failure of the
preceding platform_get_resource().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Check for failure from platform_get_resource() (this check actually happens
inside devm_ioremap_resource()) before dereferencing the pointer returned
from platform_get_resource().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Check for failure of devm_ioremap_resource().
devm_ioremap_resource() validates the resource it receives, so if we check
for devm_ioremap_resource() failure, we need not check for failure of the
preceding platform_get_resource().
[bhelgaas: changelog]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Communications with a hardware vendor confirm that the expected behaviour
on systems that set the FADT ASPM disable bit but which still grant full
PCIe control is for the OS to leave any BIOS configuration intact and
refuse to touch the ASPM bits. This mimics the behaviour of Windows.
Signed-off-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Clarify pci.txt so it matches the "do not add new entries unless they are
shared between multiple drivers" comment in include/linux/pci_ids.h.
[bhelgaas: changelog, strengthen language]
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are some fixes for v4.0. I apologize for how late they are. We
were hoping for some better fixes, but couldn't get them polished in
time. These fix:
- a Xen domU oops with PCI passthrough devices
- a sparc T5 boot failure
- a STM SPEAr13xx crash (use after initdata freed)
- a cpcihp hotplug driver thinko
- an AER thinko that printed stack junk
Details:
Enumeration
- Don't look for ACPI hotplug parameters if ACPI is disabled (Bjorn Helgaas)
Resource management
- Revert "sparc/PCI: Clip bridge windows to fit in upstream windows" (Bjorn Helgaas)
AER
- Avoid info leak in __print_tlp_header() (Rasmus Villemoes)
PCI device hotplug
- Add missing curly braces in cpci_configure_slot() (Dan Carpenter)
ST Microelectronics SPEAr13xx host bridge driver
- Drop __initdata from spear13xx_pcie_driver (Matwey V. Kornilov)
* tag 'pci-v4.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "sparc/PCI: Clip bridge windows to fit in upstream windows"
PCI: Don't look for ACPI hotplug parameters if ACPI is disabled
PCI: cpcihp: Add missing curly braces in cpci_configure_slot()
PCI/AER: Avoid info leak in __print_tlp_header()
PCI: spear: Drop __initdata from spear13xx_pcie_driver
|
|
Adds an entry for Creative USB X-Fi to the rc_config array in
mixer_quirks.c to allow use of volume knob on the device.
Adds support for newer X-Fi Pro card, known as "Model No. SB1095"
with USB ID "041e:3237"
Signed-off-by: Dmitry M. Fedin <dmitry.fedin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Feature macros work on sio_data as well, so use them there.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
"ocfs2 syncs the wrong range" had been broken; prior to it the
code was doing the wrong thing in case of O_APPEND, all right,
but _after_ it we were syncing the wrong range in 100% cases.
*ppos, aka iocb->ki_pos is incremented prior to that point,
so we are always doing sync on the area _after_ the one we'd
written to.
Spotted by Joseph Qi <joseph.qi@huawei.com> back in January;
unfortunately, I'd missed his mail back then ;-/
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
These are all register available in nios2.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
|
|
The comment line regarding IOMMU_INIT and IOMMU_INIT_FINISH
macros is incorrect:
"The standard vs the _FINISH differs in that the _FINISH variant
will continue detecting other IOMMUs in the call list..."
It should be "..the *standard* variant will continue
detecting..."
Fix that. Also, make it readable while at it.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: konrad.wilk@oracle.com
Fixes: 6e9636693373 ("x86, iommu: Update header comments with appropriate naming")
Link: http://lkml.kernel.org/r/1428508017-5316-1-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
execve stubs are 7 bytes only. Padding them to 16 bytes is a
waste.
text data bss dec hex filename
12594 0 0 12594 3132 entry_64.o.before
12530 0 0 12530 30f2 entry_64.o
Run-tested.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1428439424-7258-8-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
It used to be used to check for _TIF_IA32, but the check has
been removed.
Remove GET_THREAD_INFO() too.
Run-tested.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1428439424-7258-7-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Replace
test
jz 1f
jmp label
1:
with
test
jnz label
Run-tested.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1428439424-7258-6-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Jumping to the very next instruction is not very useful:
jmp label
label:
Removing the jump.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1428439424-7258-5-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Replace "call func; ret" with "jmp func".
Run-tested.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1428439424-7258-4-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The change which affected how execve clears EXTRA_REGS missed
32-bit execve syscalls.
Fix this by using 64-bit execve stub epilogue for them too.
Run-tested.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1428439424-7258-3-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This is a preparatory patch for moving stub32_execve[at]() to this
file. It makes sense to have all execve stubs in one place, so
that they can reuse code.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1428439424-7258-2-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Similarly to stub_execve, we can reuse the epilogue in
stub_rt_sigreturn() and stub_x32_rt_sigreturn().
Add a comment explaining why we can't eliminage SAVE_EXTRA_REGS
here.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1428439424-7258-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit 1bc9e47aa8e4 ("powerpc/jump_label: Use HAVE_JUMP_LABEL")
converted uses of CONFIG_JUMP_LABEL to HAVE_JUMP_LABEL in
some assembly files.
HAVE_JUMP_LABEL is defined in linux/jump_label.h, so we need to
include this or we always get the non jump label fallback code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: benh@kernel.crashing.org
Cc: catalin.marinas@arm.com
Cc: davem@davemloft.net
Cc: heiko.carstens@de.ibm.com
Cc: jbaron@akamai.com
Cc: linux@arm.linux.org.uk
Cc: linuxppc-dev@lists.ozlabs.org
Cc: liuj97@gmail.com
Cc: mgorman@suse.de
Cc: mmarek@suse.cz
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: rostedt@goodmis.org
Cc: schwidefsky@de.ibm.com
Cc: will.deacon@arm.com
Fixes: 1bc9e47aa8e4 ("powerpc/jump_label: Use HAVE_JUMP_LABEL")
Link: http://lkml.kernel.org/r/1428551492-21977-3-git-send-email-anton@samba.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
To use jump labels in assembly we need the HAVE_JUMP_LABEL
define, so we select a fallback version if the toolchain does
not support them.
Modify linux/jump_label.h so it can be included by assembly
files. We also need to add -DCC_HAVE_ASM_GOTO to KBUILD_AFLAGS.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: benh@kernel.crashing.org
Cc: catalin.marinas@arm.com
Cc: davem@davemloft.net
Cc: heiko.carstens@de.ibm.com
Cc: jbaron@akamai.com
Cc: linux@arm.linux.org.uk
Cc: linuxppc-dev@lists.ozlabs.org
Cc: liuj97@gmail.com
Cc: mgorman@suse.de
Cc: mmarek@suse.cz
Cc: mpe@ellerman.id.au
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: rostedt@goodmis.org
Cc: schwidefsky@de.ibm.com
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1428551492-21977-2-git-send-email-anton@samba.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Wrap asm/jump_label.h for all archs with #ifndef __ASSEMBLY__.
Since these are kernel only headers, we don't need #ifdef
__KERNEL__ so can simplify things a bit.
If an architecture wants to use jump labels in assembly, it
will still need to define a macro to create the __jump_table
entries (see ARCH_STATIC_BRANCH in the powerpc asm/jump_label.h
for an example).
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: benh@kernel.crashing.org
Cc: catalin.marinas@arm.com
Cc: davem@davemloft.net
Cc: heiko.carstens@de.ibm.com
Cc: jbaron@akamai.com
Cc: linux@arm.linux.org.uk
Cc: linuxppc-dev@lists.ozlabs.org
Cc: liuj97@gmail.com
Cc: mgorman@suse.de
Cc: mmarek@suse.cz
Cc: mpe@ellerman.id.au
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: rostedt@goodmis.org
Cc: schwidefsky@de.ibm.com
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1428551492-21977-1-git-send-email-anton@samba.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Currently it is not possible to use 'mmc-pwrseq-simple' property with this
driver because mmc_of_parse() is never called.
mmc_of_parse() calls mmc_pwrseq_alloc() that manages MMC power sequence and
allows passing GPIOs in the devicetree to properly power/reset the Wifi
chipset.
When using mmc_of_parse() we no longer need to have custom code to request
card-detect and write-protect pins, as this can now be handled by the mmc
core.
Tested on a imx6sl-warp board where BT/Wifi is functional and also on a
imx6q-sabresd.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It is possible for the cmd11 interrupt to fire and delete the
cmd11_timer before the cmd11_timer was actually setup. Let's fix this
race by adding a few spinlocks. Note that the race wasn't seen in
practice without adding some printk statements, but it still seems
wise to fix.
Fixes: 5c935165da79 ("mmc: dw_mmc: Add a timeout for sending CMD11")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If we get an unexpected cmd11 timeout we shouldn't actually treat it
as a timeout (not that we really expect to get an unexpected cmd11
timeout, but still).
Fixes: 5c935165da79 ("mmc: dw_mmc: Add a timeout for sending CMD11")
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Although the cmd11 interrupt should come within 2ms, that's a very
short time. Let's increase the timeout to be really sure that we
don't get an accidnetal timeout. One case in particular this is
useful is if you've got a serial console and printk in just the right
places. Under that scenario I've seen delays of up to 130ms before
the interrupt fired.
CMD11 is only sent during card insertion, so this extra timeout
shouldn't be terrible.
Fixes: 5c935165da79 ("mmc: dw_mmc: Add a timeout for sending CMD11")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The dw_mmc driver changes to make the IO accesors endian agnostic did not
take into account the fifo accesses do not need to be swapped. To fix this
add a mmci_fifo_read/write wrapper to allow these to be passed through the
IO without being swapped.
Since these are now specific functions, it would be easier just to store
the pointer to the fifo registers in the host block instead of the offset
to them. So change the host->data_offset to host->fifo_reg (which also
means we catch all the places this is read or written).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The dw_mmc driver does not take into account the processor may be in
big endian when writing the descriptors. Change the descriptors for
the 32bit IDMA to use __le32 and ensure they are suitably swapped
before writing.
Note, this has not been tested as the socfpga driver does not try to
use idma.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The dw_mmc driver does not use endian agnostic IO accessors, so fix
the use of __raw reads and writes to be the relaxed versions.
This fixes the dw_mmc driver initialisation on Altera socfpga in big endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Similar to what Linus suggested for rwsem_spin_on_owner(), in
mutex_spin_on_owner() instead of having while (true) and
breaking out of the spin loop on lock->owner != owner, we can
have the loop directly check for while (lock->owner == owner) to
improve the readability of the code.
It also shrinks the code a bit:
text data bss dec hex filename
3721 0 0 3721 e89 mutex.o.before
3705 0 0 3705 e79 mutex.o.after
Signed-off-by: Jason Low <jason.low2@hp.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Link: http://lkml.kernel.org/r/1428521960-5268-2-git-send-email-jason.low2@hp.com
[ Added code generation info. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix
drivers/hwmon/ibmpowernv.c: In function 'get_logical_cpu':
drivers/hwmon/ibmpowernv.c:121:3:
error: implicit declaration of function 'get_hard_smp_processor_id'
seen for some configurations, possibly if SMP is not configured.
Fixes: 3df2f59f0aae ("hwmon: (ibmpowernv) pretty print labels")
Cc: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Thermal framework may already be ready and cooling policies might
already be functional when we are attempting to register gpio fan as
a cooling device. This can be reproduced by changing probe order in
which registration of various modules are done in a system. In such
a case, kernel generates an oops since the data structures are not
completely populated with the wrong assumption that thermal framework
is not yet ready. Fix this by reordering the thermal framework
registration to occur after hwmon registration of the fan is complete.
Example kernel oops:
[ 149.005828] Unable to handle kernel NULL pointer dereference at virtual address 0000008c
[ 149.014369] pgd = ecf48000
[ 149.017204] [0000008c] *pgd=ac065831, *pte=00000000, *ppte=00000000
[ 149.023820] Internal error: Oops: 17 [#1] SMP ARM
[ 149.028745] Modules linked in: gpio_fan(+) cpufreq_dt ipv6 evdev leds_gpio led_class omap_wdt phy_omap_usb2 rtc_palmas palmas_pwrbutton tmp102 ti_soc_thermal dwc3_omap thermal_sys extcon rtc_omap rtc_ds1307 hwmon
[ 149.048629] CPU: 1 PID: 1183 Comm: modprobe Not tainted 4.0.0-rc7-next-20150407-00002-g7a82da074c99 #3
[ 149.058383] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 149.064763] task: edec1240 ti: ec0e0000 task.ti: ec0e0000
[ 149.070421] PC is at dev_driver_string+0x0/0x38
[ 149.075165] LR is at __dev_printk+0x24/0x70
[ 149.079540] pc : [<c03d6cd0>] lr : [<c03d72c4>] psr: 20000013
[ 149.079540] sp : ec0e1c28 ip : edec1240 fp : 00000000
[ 149.091568] r10: edf3eee0 r9 : 00000000 r8 : ffffffff
[ 149.097040] r7 : edf3eea0 r6 : 00000034 r5 : 00000010 r4 : ec0e1c44
[ 149.103871] r3 : ec0e1c4c r2 : ec0e1c44 r1 : c079d800 r0 : 00000010
[ 149.110709] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 149.118182] Control: 10c5387d Table: acf4806a DAC: 00000015
[ 149.124198] Process modprobe (pid: 1183, stack limit = 0xec0e0218)
[ 149.130673] Stack: (0xec0e1c28 to 0xec0e2000)
[ 149.135235] 1c20: 60000013 c05e2ae0 00000000 edf3ec00 ec934a10 c03d73d4
...
[ 149.392230] 1fe0: befe1888 befe1878 00019418 b6ea08f0 80000010 00000003 00000000 00000000
[ 149.400798] [<c03d6cd0>] (dev_driver_string) from [<c03d72c4>] (__dev_printk+0x24/0x70)
[ 149.409193] [<c03d72c4>] (__dev_printk) from [<c03d73d4>] (dev_warn+0x34/0x48)
[ 149.416767] [<c03d73d4>] (dev_warn) from [<bf0f54fc>] (get_fan_speed_index+0x94/0xa4 [gpio_fan])
[ 149.425980] [<bf0f54fc>] (get_fan_speed_index [gpio_fan]) from [<bf0f5524>] (gpio_fan_get_cur_state+0x18/0x30 [gpio_fan])
[ 149.437476] [<bf0f5524>] (gpio_fan_get_cur_state [gpio_fan]) from [<bf02767c>] (thermal_zone_trip_update+0xe8/0x2a4 [thermal_sys])
[ 149.449794] [<bf02767c>] (thermal_zone_trip_update [thermal_sys]) from [<bf027844>] (step_wise_throttle+0xc/0x74 [thermal_sys])
[ 149.461832] [<bf027844>] (step_wise_throttle [thermal_sys]) from [<bf024ff4>] (handle_thermal_trip+0x5c/0x188 [thermal_sys])
[ 149.473603] [<bf024ff4>] (handle_thermal_trip [thermal_sys]) from [<bf0256c4>] (thermal_zone_device_update+0x94/0x108 [thermal_sys])
[ 149.486104] [<bf0256c4>] (thermal_zone_device_update [thermal_sys]) from [<bf026470>] (__thermal_cooling_device_register+0x2e8/0x374 [thermal_sys])
[ 149.499956] [<bf026470>] (__thermal_cooling_device_register [thermal_sys]) from [<bf0f58e4>] (gpio_fan_probe+0x350/0x4d0 [gpio_fan])
[ 149.512438] [<bf0f58e4>] (gpio_fan_probe [gpio_fan]) from [<c03db8a0>] (platform_drv_probe+0x48/0x98)
[ 149.522109] [<c03db8a0>] (platform_drv_probe) from [<c03da30c>] (driver_probe_device+0x1b0/0x26c)
[ 149.531399] [<c03da30c>] (driver_probe_device) from [<c03da45c>] (__driver_attach+0x94/0x98)
[ 149.540238] [<c03da45c>] (__driver_attach) from [<c03d8bb0>] (bus_for_each_dev+0x54/0x88)
[ 149.548814] [<c03d8bb0>] (bus_for_each_dev) from [<c03d9a34>] (bus_add_driver+0xdc/0x1d4)
[ 149.557381] [<c03d9a34>] (bus_add_driver) from [<c03dac30>] (driver_register+0x78/0xf4)
[ 149.565765] [<c03dac30>] (driver_register) from [<c0009784>] (do_one_initcall+0x80/0x1d8)
[ 149.574340] [<c0009784>] (do_one_initcall) from [<c00c2278>] (do_init_module+0x5c/0x1b8)
[ 149.582833] [<c00c2278>] (do_init_module) from [<c00c3bbc>] (load_module+0x1720/0x1dcc)
[ 149.591212] [<c00c3bbc>] (load_module) from [<c00c43d0>] (SyS_finit_module+0x68/0x6c)
[ 149.599418] [<c00c43d0>] (SyS_finit_module) from [<c000f3c0>] (ret_fast_syscall+0x0/0x4c)
[ 149.607994] Code: 15830000 e1a00006 e28dd008 e8bd8070 (e590307c)
Cc: Eduardo Valentin <edubezval@gmail.com>
Fixes: b5cf88e46bad ("(gpio-fan): Add thermal control hooks")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull drm fixes from Dave Airlie:
"Final drm fixes: one core locking imbalance regression, and a bunch of
i915 baytrail s/r fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: fix drm_mode_getconnector() locking imbalance regression
drm/i915/vlv: remove wait for previous GFX clk disable request
drm/i915/chv: Remove Wait for a previous gfx force-off
drm/i915/vlv: save/restore the power context base reg
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph revert from Sage Weil:
"This corrects a recent misadventure with __GFP_MEMALLOC and
PF_MEMALLOC; it turns out it's not a good fit for RBD and we're better
off relying on dirty page throttling"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
Revert "libceph: use memalloc flags for net IO"
|
|
Merge misc fixes from Andrew Morton:
"Three fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: numa: disable change protection for vma(VM_HUGETLB)
include/linux/dmapool.h: declare struct device
mm: move zone lock to a different cache line than order-0 free page lists
|
|
into irq/core
irqchip core changes for v4.0 from Jason Cooper
- ST
- New driver, irq-st
- Renesas
- Use u32 type for 32bit regs
|
|
Unlike most (all?) other copies from user space, kernel module loading
is almost unlimited in size. So we do a potentially huge
"copy_from_user()" when we copy the module data from user space to the
kernel buffer, which can be a latency concern when preemption is
disabled (or voluntary).
Also, because 'copy_from_user()' clears the tail of the kernel buffer on
failures, even a *failed* copy can end up wasting a lot of time.
Normally neither of these are concerns in real life, but they do trigger
when doing stress-testing with trinity. Running in a VM seems to add
its own overheadm causing trinity module load testing to even trigger
the watchdog.
The simple fix is to just chunk up the module loading, so that it never
tries to copy insanely big areas in one go. That bounds the latency,
and also the amount of (unnecessarily, in this case) cleared memory for
the failure case.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rule for 'copy_from_user()' is that it zeroes the remaining kernel
buffer even when the copy fails halfway, just to make sure that we don't
leave uninitialized kernel memory around. Because even if we check for
errors, some kernel buffers stay around after thge copy (think page
cache).
However, the x86-64 logic for user copies uses a copy_user_generic()
function for all the cases, that set the "zerorest" flag for any fault
on the source buffer. Which meant that it didn't just try to clear the
kernel buffer after a failure in copy_from_user(), it also tried to
clear the destination user buffer for the "copy_in_user()" case.
Not only is that pointless, it also means that the clearing code has to
worry about the tail clearing taking page faults for the user buffer
case. Which is just stupid, since that case shouldn't happen in the
first place.
Get rid of the whole "zerorest" thing entirely, and instead just check
if the destination is in kernel space or not. And then just use
memset() to clear the tail of the kernel buffer if necessary.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the required hooks for the internal state of an interrupt
to be exposed to other subsystems.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Phong Vo <pvo@apm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tin Huynh <tnhuynh@apm.com>
Cc: Y Vo <yvo@apm.com>
Cc: Toan Le <toanle@apm.com>
Cc: Bjorn Andersson <bjorn@kryo.se>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/1426676484-21812-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
