| Age | Commit message (Collapse) | Author |
|---|
|
The DeviceTree Specification v0.3 specifies that the cache node
'compatible' and 'cache-level' properties are 'required'. Cf.
s3.8 Multi-level and Shared Cache Nodes
The 'cache-unified' property should be present if one of the
properties for unified cache is present ('cache-size', ...).
Update the Device Trees accordingly.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The 'enable-active-low' property is not a valid one.
Only 'enable-active-high' is valid, and when this property is absent
the gpio regulator will act as active low by default.
Remove the invalid 'enable-active-low' property.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add dma-channel-mask property in Tegra GPCDMA device tree node.
The property would help to specify the channels to be used in
kernel and reserve few for the firmware. This was previously
achieved by limiting the channel number to 31 in the driver.
This is wrong and does not align with the hardware. Correct this
and update the interrupts property to list all 32 interrupts.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Fix the starting address of the non-prefetchable aperture of PCIe C3
controller.
Fixes: ec142c44b026 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra234 DT")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
According to the DT schema in usb-device.yaml, each USB device node
needs a compatible string, so add one for the built-in USB Ethernet
device on Jetson TX1.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The registers for the AON pinmux reside in a partition different from
the registers for the main pinmux. Instead of treating them as one and
the same device, split them up so that they are each their own devices.
Also add gpio-ranges properties to the corresponding GPIO controllers
such that the pinmux and GPIO controllers can be paired up properly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the ECAM aperture information for all the PCIe controllers of
Tegra234.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra PWFM controllers use a single clock, so there's no need for a
clock-names property.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add and enable AON and LIC GTE nodes by default.
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra Combined UART (TCU) is the default serial interface for Jetson
Xavier and Orin platforms and so update the bootargs for these platforms
to use the TCU.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Enable additional PWM controllers in device tree so that the PWM pins on
the Jetson AGX Orin Developer Kit 40-pin header can be used.
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The unit-address of a node should be separated from the opening brace by
a space.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The P2U nodes that were recently added were not added in the correct
order. Sort them in the right place by unit-address.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add device tree node for Tegra234 SDMMC1 instance.
Add and enable SD card instance in device tree.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Populate the SBSA UART for Tegra234 and enable this UART for Jetson AGX
Orin.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the PWM fan node for the Tegra234 Jetson AGX Orin platform.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Populate all the PWM devices for Tegra234. Finally, update the
compatible string for the existing 'pwm1' node to just be 'tegra194-pwm'
and remove the fallback to 'tegra186-pwm', which aligns with the
binding documentation.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Commit 156af9de0932 ("arm64: tegra: Add Tegra234 I2C devicetree nodes")
populated the I2C device nodes for Tegra234. One of these nodes
contains the property 'nvidia,hw-instance-id' which is neither
documented or used. Remove this unused property.
Fixes: 156af9de0932 ("arm64: tegra: Add Tegra234 I2C devicetree nodes")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
commit edf408b946d3 ("PCI: dwc: Validate iATU outbound mappings against
hardware constraints") exposes an issue with the existing partitioning of
the aperture space where the Prefetchable apertures of controllers
C5, C7 and C9 in Tegra234 cross the 32GB boundary hardware constraint.
This patch makes sure that the Prefetchable region doesn't spill over
the 32GB boundary.
Fixes: ec142c44b026 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra234 DT")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a device tree node for NVDEC on Tegra234.
Booting the firmware requires some information regarding offsets
within the firmware binary. These are passed through the device
tree, but since the values vary depending on the firmware version,
and the firmware itself is not available to the OS, the flasher is
expected to provide a device tree overlay with values corresponding
to the firmware it is flashing. The overlay then replaces the
placeholder values here.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The currently specified 'ranges' properties don't actually include
all devices under the host1x bus on Tegra194 and Tegra234. Expand
them appropriately.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
|
|
Convert the Tegra XUSB controller bindings from the free-form text
format to json-schema.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Convert the Tegra PWFM bindings from the free-form text format to
json-schema.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra194 has two separate instances of the pin controller, one called
AON (in the always-on domain) and another called "main". Instead of
treating them as a single pin controller, split them up into two
separate controllers. Doing so allows the mapping between the pinmux and
GPIO controllers to be trivial identity mappings and more cleanly
separates the AON from the main IP blocks.
Note that while this changes the DT node in an incompatible way, this
doesn't have any practical implications for backwards-compatibility. The
reason for this is that device trees have only reconfigured a very
narrow subset of pins of the main controller, so the new driver will
remain backwards-compatible with old device trees.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Convert the NVIDIA Tegra pinmux controller bindings from the free-form
text format to json-schema.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add support for ECAM aperture that is only supported for Tegra234
devices.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Co-developed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add compatible for nvidia,tegra234-pwm with nvidia,tegra194-pwm as a
fallback. The PWM controller blocks are identical to the ones found on
the Tegra194 SoC. No driver changes are required and compatible string
"nvidia,tegra194-pwm" will be used as a fallback.
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Update NVDEC bindings for Tegra234. This new engine version only has
two memory clients, but now requires three clocks, and as a bigger
change the engine loads firmware from a secure carveout configured by
the bootloader.
For the latter, we need to add a phandle to the memory controller
to query the location of this carveout, and several other properties
containing offsets into the firmware inside the carveout. This
carveout is not accessible by the CPU, but is needed by NVDEC,
so we need this information to be relayed from the bootloader.
As the binding was getting large with many conditional properties,
also split the Tegra234 version out into a separate file.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Update the device-tree clock, memory, power and reset headers for
Tegra234 by adding the definitions for all the various devices.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a basic support for the Sony Xperia M5 (codename "Holly")
smartphone, powered by a MediaTek Helio X10 SoC.
This achieves a console boot.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027095504.37432-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add a compatible for the Sony Xperia M5 smartphone.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221027095504.37432-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add the mmc nodes to support all of the four controllers, used for
eMMC, SD/MicroSD and SDIO storage.
All of these controller nodes are left disabled by default, as
usage is board dependent.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027095504.37432-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This SoC has a DMA controller with tx/rx channels for all of the
UART controller IPs: add the apdma node and wire up the DMAs on
all controllers.
When one of the UART controllers is used as a serial console,
the DMA will be automatically ignored.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027095504.37432-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The UART nodes had a dummy clock for early bringup, as it is
expected that these are left on by the bootloader: now that
the pericfg clock controller is supported, we can replace
them with the real clocks.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027095504.37432-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add nodes for topckgen, infracfg and pericfg, providing various
clocks and resets and needed to support basic IPs of this SoC.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027095504.37432-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
In cherry projects, we use edptx as the internal display interface
and use dptx as the external display interface. To support this, we
need to add more properties.
- Add pinctrls for edptx and dptx.
- Add ports for edptx and dptx.
The port connections for the internal and external display:
dp-intf0 -> edptx -> panel
dp-intf1 -> dptx
The edptx endpoint is kept empty for now, as the panel addition will
come in a later commit.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110063716.25677-5-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Dp-intfs provide the pixel data to edptx and dptx. To support edptx
and dptx, we need to add dp-intf0 and dp-intf1 ports.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110063716.25677-4-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
In MT8195, we use edptx as the internal display interface and use
dptx as the external display interface. Therefore, we need to add
these nodes to support the internal display and the external display.
- Add dp calibration data in the efuse node.
- Add edptx and dptx nodes for MT8195.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110063716.25677-3-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Dp-intfs provide the pixel data to edptx and dptx. To support edptx
and dptx, we need to add dp-intf0 and dp-intf1 nodes.
Dp-intf0 is for edptx and dp-intf1 is for dptx.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110063716.25677-2-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Update its unit name to oscillator-26m and remove the unneeded unit
address to fix a unit_address_vs_reg warning.
Fixes: 464c510f60c6 ("arm64: dts: mediatek: add mt6797 support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-9-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Fix the pinctrl submodes and optee node to remove unneeded unit address,
fixing all unit_address_vs_reg warnings.
Fixes: 9983822c8cf9 ("arm64: dts: mediatek: add pumpkin board dts")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-8-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Update the names to regulator-usb-p{0-3}-vbus to fix unit_address_vs_reg
warnings for those.
Fixes: 1724f4cc5133 ("arm64: dts: Add USB3 related nodes for MT2712")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Update the names to regulator-vproc-buck{0,1} to fix unit_addres_vs_reg
warnings for those.
Fixes: f75dd8bdd344 ("arm64: dts: mediatek: add mt2712 cpufreq related device nodes")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The unit address for the pinctrl node is (0x)1000b000 and not
(0x)10005000, which is the syscfg_pctl_a address instead.
This fixes the following warning:
arch/arm64/boot/dts/mediatek/mt2712e.dtsi:264.40-267.4: Warning
(unique_unit_address): /syscfg_pctl_a@10005000: duplicate
unit-address (also used in node /pinctrl@10005000)
Fixes: f0c64340b748 ("arm64: dts: mt2712: add pintcrl device node.")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Rename the fixed-clock oscillators to remove the unit address.
This solves unit_address_vs_reg warnings.
Fixes: 5d4839709c8e ("arm64: dts: mt2712: Add clock controller device nodes")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Rename fixed-clock oscillators to oscillator-26m and oscillator-32k
and remove the unit address to fix the unit_address_vs_reg warning;
fix the unit address for interrupt and intpol controllers by
removing a leading zero in their unit address.
This commit fixes the following warnings:
(unit_address_vs_reg): /oscillator@0: node has a unit name, but
no reg or ranges property
(unit_address_vs_reg): /oscillator@1: node has a unit name, but
no reg or ranges property
(simple_bus_reg): /soc/interrupt-controller@0c000000: simple-bus
unit address format error, expected "c000000"
(simple_bus_reg): /soc/intpol-controller@0c53a650: simple-bus
unit address format error, expected "c53a650"
Fixes: 4c7a6260775d ("arm64: dts: add dts nodes for MT6779")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Rename the oscillator fixed-clock to oscillator-40m and remove
the unit address to fix warnings.
arch/arm64/boot/dts/mediatek/mt7986a.dtsi:17.23-22.4: Warning
(unit_address_vs_reg): /oscillator@0: node has a unit name,
but no reg or ranges property
Fixes: 1f9986b258c2 ("arm64: dts: mediatek: add clock support for mt7986a")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The capacity-dmips-mhz parameter was miscalculated: this SoC runs
the first (Cortex-A55) cluster at a maximum of 2000MHz and the
second (Cortex-A78) cluster at a maximum of 3000MHz.
In order to calculate the right capacity-dmips-mhz, the following
test was performed:
1. CPUFREQ governor was set to 'performance' on both clusters
2. Ran dhrystone with 500000000 iterations for 10 times on each cluster
3. Calculate the mean result for each cluster
4. Calculate DMIPS/MHz: dmips_mhz = dmips_per_second / cpu_mhz
5. Scale results to 1024:
result_c0 = (dmips_mhz_c0 - min_dmips_mhz(c0, c1)) /
(max_dmips_mhz(c0, c1) - min_dmips_mhz(c0, c1)) * 1024
The mean results for this SoC are:
Cluster 0 (LITTLE): 11990400 Dhry/s
Cluster 1 (BIG): 59809036 Dhry/s
The calculated scaled results are:
Cluster 0: 307,934312801831 (rounded to 308)
Cluster 1: 1024
Fixes: 37f2582883be ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221005093404.33102-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- Earphone stereo jack detect
- 5inch 854×480 MIPI-DSI TFT LCD
Link: https://lore.kernel.org/r/20221031-b4-odroid-go-ultra-initial-v2-2-a3df1e09b0af@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
