| Age | Commit message (Collapse) | Author |
|---|
|
As noted in dwmac4_wrback_get_rx_timestamp_status the timestamp is found
in the context descriptor following the current descriptor. However the
current code looks for the context descriptor in the current
descriptor, which will always fail.
Signed-off-by: Fredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using GMAC4 the value written in PTP_SSIR should be shifted however
the shifted value is also used in subsequent calculations which results
in a bad timestamp value.
Signed-off-by: Fredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When, during a join operation, or during message transmission, a group
member needs to be added to the group's 'congested' list, we sort it
into the list in ascending order, according to its current advertised
window size. However, we miss the case when the member is already on
that list. This will have the result that the member, after the window
size has been decremented, might be at the wrong position in that list.
This again may have the effect that we during broadcast and multicast
transmissions miss the fact that a destination is not yet ready for
reception, and we end up sending anyway. From this point on, the
behavior during the remaining session is unpredictable, e.g., with
underflowing window sizes.
We now correct this bug by unconditionally removing the member from
the list before (re-)sorting it in.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In recent tests with new adapters, it was discovered that ARP
packets were not being properly processed. This patch adds
support for ARP packet headers to be passed to backing adapters,
if necessary.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thomas Falcon says:
====================
ibmvnic: Fix and increase maximum TX/RX queues
This series renames IBMVNIC_MAX_TX_QUEUES to IBMVNIC_MAX_QUEUES since
it is used to allocate both RX and TX queues. The value is also increased
to accommodate newer hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increase the number of queues allocated to accommodate recent
network adapter inclusions on the IBM vNIC platform.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This value denotes the maximum number of TX queues but is used
to allocate both RX and TX queues.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For T6, tid start range should be read from
LE_DB_ACTIVE_TABLE_START_INDEX_A register.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-12-18
Here's the first bluetooth-next pull request for the 4.16 kernel.
- hci_ll: multiple cleanups & fixes
- Remove Gustavo Padovan from the MAINTAINERS file
- Support BLE Adversing while connected (if the controller can do it)
- DT updates for TI chips
- Various other smaller cleanups & fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow the boot loader to specify the MAC address in the device tree
to override the EEPROM, or in case no EEPROM is present.
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Tristram Ha <tristram.ha@micrel.com>
Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now it's using IPV6_MIN_MTU as the min mtu in ip6_tnl_xmit, but
IPV6_MIN_MTU actually only works when the inner packet is ipv6.
With IPV6_MIN_MTU for ipv4 packets, the new pmtu for inner dst
couldn't be set less than 1280. It would cause tx_err and the
packet to be dropped when the outer dst pmtu is close to 1280.
Jianlin found it by running ipv4 traffic with the topo:
(client) gre6 <---> eth1 (route) eth2 <---> gre6 (server)
After changing eth2 mtu to 1300, the performance became very
low, or the connection was even broken. The issue also affects
ip4ip6 and ip6ip6 tunnels.
So if the inner packet is ipv4, 576 should be considered as the
min mtu.
Note that for ip4ip6 and ip6ip6 tunnels, the inner packet can
only be ipv4 or ipv6, but for gre6 tunnel, it may also be ARP.
This patch using 576 as the min mtu for non-ipv6 packet works
for all those cases.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same fix as the patch "ip_gre: remove the incorrect mtu limit for
ipgre tap" is also needed for ip6_gre.
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipgre tap driver calls ether_setup(), after commit 61e84623ace3
("net: centralize net_device min/max MTU checking"), the range
of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
It causes the dev mtu of the ipgre tap device to not be greater
than 1500, this limit value is not correct for ipgre tap device.
Besides, it's .change_mtu already does the right check. So this
patch is just to set max_mtu as 0, and leave the check to it's
.change_mtu.
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike ip tunnels, now vxlan doesn't do any pmtu update for
upper dst pmtu, even if it doesn't match the lower dst pmtu
any more.
The problem can be reproduced when reducing the vxlan lower
dev's pmtu when running netperf. In jianlin's testing, the
performance went to 1/7 of the previous.
This patch is to update the upper dst pmtu to match the lower
dst pmtu on tx path so that packets can be sent out even when
lower dev's pmtu has been changed.
It also works for metadata dst.
Note that this patch doesn't process any pmtu icmp packet.
But even in the future, the support for pmtu icmp packets
process of udp tunnels will also needs this.
The same thing will be done for geneve in another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under certain conditions EMAC stop reception of incoming packets and
continuously increment R_MISS register instead of saving data into
provided buffer. The commit implement workaround for such situation.
Then the stall detected EMAC will be restarted.
On device the stall looks like the device lost it's dynamic IP address.
ifconfig shows that interface error counter rapidly increments.
At the same time on the DHCP server we can see continues DHCP-requests
from device.
In real network stalls happen really rarely. To make them frequent the
broadcast storm[1] should be simulated. For simulation it is necessary
to make following connections:
1. connect radxarock to 1st port of switch
2. connect some PC to 2nd port of switch
3. connect two other free ports together using standard ethernet cable,
in order to make a switching loop.
After that, is necessary to make a broadcast storm. For example, running on
PC 'ping' to some IP address triggers ARP-request storm. After some
time (~10sec), EMAC on rk3188 will stall.
Observed and tested on rk3188 radxarock.
[1] https://en.wikipedia.org/wiki/Broadcast_radiation
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
arc_emac_rx() has some issues found by code review.
In case netdev_alloc_skb_ip_align() or dma_map_single() failure
rx fifo entry will not be returned to EMAC.
In case dma_map_single() failure previously allocated skb became
lost to driver. At the same time address of newly allocated skb
will not be provided to EMAC.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current solution would setup fixed and force link of 1Gbps to the both
GMAC on the default. However, The GMAC should always be put to link down
state when the GMAC is disabled on certain target boards. Otherwise,
the driver possibly receives unexpected data from the floating hardware
connection through the unused GMAC. Although the driver had been added
certain protection in RX path to get rid of such kind of unexpected data
sent to the upper stack.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 63dd00fa3e524c27cc0509190084ab147ecc8ae2.
RAUHT DELETE_ALL seems to trigger a bug in FW. That manifests by later
calls to RAUHT ADD of an IPv6 neighbor to fail with "bad parameter"
error code.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Fixes: 63dd00fa3e52 ("mlxsw: spectrum_router: Add batch neighbour deletion")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jonas Gorski says:
====================
bcm63xx_enet: remove mac_id usage
This patchset aims at reducing the platform device id number usage with
the target of making it eventually possible to probe the driver through OF.
Runtested on BCM6358.
Since the patches touch mostly net/, they should go through net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Directly use the platform device for generating the miibus name. This
removes the last user of bcm_enet_priv::mac_id and we can remove the
field.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enabling the ephy clock for mac 1 is harmless, and the actual usage of
the ephy is not restricted to mac 0, so we might as well remove the
check.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To reduce the reliance on device ids, pass the dma channel numbers to
the enet devices as platform data.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have the individual clocks available as "enet" we
don't need to rely on the device id for them anymore.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Haishuang Yan says:
====================
net: speedup geneve/vxlan tunnels dismantle
This patch series add batching to vxlan/geneve tunnels so that netns
dismantles are less costly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we now hold RTNL lock in geneve_exit_net, it's better batch them
to speedup geneve tunnel dismantle.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we now hold RTNL lock in vxlan_exit_net, it's better to batch them
to speedup vxlan tunnels dismantle.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since both first_tx_ctx and tx_skb are the head of tx ctx, it not
necessary to use two structure members to statically indicate
the head of tx ctx. So first_tx_ctx is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael Chan says:
====================
Introduce NETIF_F_GRO_HW
Introduce NETIF_F_GRO_HW feature flag and convert drivers that support
hardware GRO to use the new flag.
v5:
- Documentation changes requested by Alexander Duyck.
- bnx2x changes requested by Manish Chopra to enable LRO by default, and
disable GRO_HW if disable_tpa module parameter is set.
v4:
- more changes requested by Alexander Duyck:
- check GRO_HW/GRO dependency in drivers's ndo_fix_features().
- Reverse the order of RXCSUM and GRO_HW dependency check in
netdev_fix_features().
- No propagation in netdev_disable_gro_hw().
v3:
- Let driver's ndo_fix_features() disable NETIF_F_LRO when NETIF_F_GRO_HW
is set instead of doing it in common netdev_fix_features().
v2:
- NETIF_F_GRO_HW flag propagation between upper and lower devices not
required (see patch 1).
- NETIF_F_GRO_HW depends on NETIF_F_GRO and NETIF_F_RXCSUM.
- Add dev_disable_gro_hw() to disable GRO_HW for generic XDP.
- Use ndo_fix_features() on all 3 drivers to drop GRO_HW when it is not
supported
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advertise NETIF_F_GRO_HW and set edev->gro_disable according to the
feature flag. Add qede_fix_features() to drop NETIF_F_GRO_HW if
XDP is running or MTU does not support GRO_HW or GRO is not set.
qede_change_mtu() also checks and disables GRO_HW if MTU is not
supported.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advertise NETIF_F_GRO_HW and turn on TPA_MODE_GRO when NETIF_F_GRO_HW
is set. Disable NETIF_F_GRO_HW in bnx2x_fix_features() if the MTU
does not support TPA_MODE_GRO or GRO is not set. bnx2x_change_mtu() also
needs to disable NETIF_F_GRO_HW if the MTU does not support it.
Original parameter disable_tpa will continue to disable LRO and GRO_HW.
Preserve the original behavior of enabling LRO by default. User has
to run ethtool -K to explicitly enable GRO_HW.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advertise NETIF_F_GRO_HW in hw_features if hardware GRO is supported.
In bnxt_fix_features(), disable GRO_HW and LRO if current hardware
configuration does not allow it. GRO_HW depends on GRO. GRO_HW is
also mutually exclusive with LRO. XDP setup will now rely on
bnxt_fix_features() to turn off aggregation. During chip init, turn on
or off hardware GRO based on NETIF_F_GRO_HW in features flag.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware should not aggregate any packets when generic XDP is installed.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce NETIF_F_GRO_HW feature flag for NICs that support hardware
GRO. With this flag, we can now independently turn on or off hardware
GRO when GRO is on. Previously, drivers were using NETIF_F_GRO to
control hardware GRO and so it cannot be independently turned on or
off without affecting GRO.
Hardware GRO (just like GRO) guarantees that packets can be re-segmented
by TSO/GSO to reconstruct the original packet stream. Logically,
GRO_HW should depend on GRO since it a subset, but we will let
individual drivers enforce this dependency as they see fit.
Since NETIF_F_GRO is not propagated between upper and lower devices,
NETIF_F_GRO_HW should follow suit since it is a subset of GRO. In other
words, a lower device can independent have GRO/GRO_HW enabled or disabled
and no feature propagation is required. This will preserve the current
GRO behavior. This can be changed later if we decide to propagate GRO/
GRO_HW/RXCSUM from upper to lower devices.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a hang issue seen when changing the MTU size from 1500 MTU
to 9000 MTU on both 5717 and 5719 chips. In discussion with Broadcom,
they've indicated that these chipsets have the same phy as the 57766
chipset, so the same workarounds apply. This has been tested by IBM
on both Power 8 and Power 9 systems as well as by Broadcom on x86
hardware and has been confirmed to resolve the hang issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_PROC_FS is disabled, we will not use the prot_inuse
counter. This adds an #ifdef to hide the variable definition in
that case. This is not a bugfix. But we can save bytes when there
are many network namespace.
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Martin Zhang <zhangjunweimartin@didichuxing.com>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some case, we want to know how many sockets are in use in
different _net_ namespaces. It's a key resource metric.
This patch add a member in struct netns_core. This is a counter
for socket-inuse in the _net_ namespace. The patch will add/sub
counter in the sk_alloc, sk_clone_lock and __sk_free.
This patch will not counter the socket created in kernel.
It's not very useful for userspace to know how many kernel
sockets we created.
The main reasons for doing this are that:
1. When linux calls the 'do_exit' for process to exit, the functions
'exit_task_namespaces' and 'exit_task_work' will be called sequentially.
'exit_task_namespaces' may have destroyed the _net_ namespace, but
'sock_release' called in 'exit_task_work' may use the _net_ namespace
if we counter the socket-inuse in sock_release.
2. socket and sock are in pair. More important, sock holds the _net_
namespace. We counter the socket-inuse in sock, for avoiding holding
_net_ namespace again in socket. It's a easy way to maintain the code.
Signed-off-by: Martin Zhang <zhangjunweimartin@didichuxing.com>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the member name will make the code more readable.
This patch will be used in next patch.
Signed-off-by: Martin Zhang <zhangjunweimartin@didichuxing.com>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few more fixes:
* hwsim:
- set To-DS bit in some frames missing it
- fix sleeping in atomic
* nl80211:
- doc cleanup
- fix locking in an error path
* build:
- don't append to created certs C files
- ship certificate pre-hexdumped
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'spi/fix/doc', 'spi/fix/imx', 'spi/fix/rspi', 'spi/fix/sun4i' and 'spi/fix/xilinx' into spi-linus
|
|
The only part of atmel_spi_remove which needs to be atomic is hardware
reset.
atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts
enabled.
atmel_spi_release_dma calls dma_release_channel and dma_release_channel
locks a mutex inside of spin_lock.
So the call of these functions can't be inside a spin_lock.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Not only does this remove the need for the hexdump code in most
normal kernel builds (still there for the extra directory), but
it also removes the need to ship binary files, which apparently
is somewhat problematic, as Randy reported.
While at it, also add the generated files to clean-files.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit ca986ad9bcd3 (nl80211: allow multiple active scheduled scan
requests) removed WIPHY_FLAG_SUPPORTS_SCHED_SCAN but left the kerneldoc
description in place, leading to this docs-build warning:
./include/net/cfg80211.h:3278: warning: Excess enum value
'WIPHY_FLAG_SUPPORTS_SCHED_SCAN' description in 'wiphy_flags'
Remove the line and gain a bit of peace.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The driver may sleep under a spinlock.
The function call path is:
hwsim_get_radio_nl (acquire the spinlock)
nlmsg_new(GFP_KERNEL) --> may sleep
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently the certs C code generation appends to the generated files,
which is most likely a leftover from commit 715a12334764 ("wireless:
don't write C files on failures"). This causes duplicate code in the
generated files if the certificates have their timestamps modified
between builds and thereby trigger the generation rules.
Fixes: 715a12334764 ("wireless: don't write C files on failures")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Same as in ieee80211_nullfunc_get, enable the TODS bit, otherwise the
nullfunc packet will not be handled in ap rx path.
(will be dropped in ieee80211_accept_frame()).
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The commit 89b89d121ffc ("ALSA: usb-audio: Add check return value for
usb_string()") added the check of the return value from
snd_usb_copy_string_desc(), which is correct per se, but it introduced
a regression. In the original code, either the "Clock Source",
"Playback Source" or "Capture Source" suffix is added after the
terminal string, while the commit changed it to add the suffix only
when get_term_name() is failing. It ended up with an incorrect ctl
name like "PCM" instead of "PCM Capture Source".
Also, even the original code has a similar bug: when the ctl name is
generated from snd_usb_copy_string_desc() for the given iSelector, it
also doesn't put the suffix.
This patch addresses these issues: the suffix is added always when no
static mapping is found. Also the patch tries to put more comments
and cleans up the if/else block for better readability in order to
avoid the same pitfall again.
Fixes: 89b89d121ffc ("ALSA: usb-audio: Add check return value for usb_string()")
Reported-and-tested-by: Mauro Santos <registo.mailling@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
With 720f228e8d31 ("bpf: fix broken BPF selftest build") the
inclusion of arch-specific header files changed. Including the
asm/bpf_perf_event.h on s390, correctly includes the s390 specific
header file. This header file tries then to include the s390
asm/ptrace.h and the build fails with:
cc -Wall -O2 -I../../../include/uapi -I../../../lib -I../../../../include/generated -I../../../include test_verifier.c
+/root/git/linux/tools/testing/selftests/bpf/libbpf.a /root/git/linux/tools/testing/selftests/bpf/cgroup_helpers.c -lcap -lelf -o
+/root/git/linux/tools/testing/selftests/bpf/test_verifier
In file included from ../../../include/uapi/asm/bpf_perf_event.h:4:0,
from ../../../include/uapi/linux/bpf_perf_event.h:11,
from test_verifier.c:29:
../../../include/uapi/../../arch/s390/include/uapi/asm/bpf_perf_event.h:7:9: error: unknown type name 'user_pt_regs'
typedef user_pt_regs bpf_user_pt_regs_t;
^~~~~~~~~~~~
make: *** [../lib.mk:109: /root/git/linux/tools/testing/selftests/bpf/test_verifier] Error 1
This is caused by a recent update to the s390 asm/ptrace.h file
that is not (yet) available in the local installation. That means,
the s390 asm/ptrace.h must be included from the tools/arch/s390
directory.
Because there is no proper framework to deal with asm specific
includes in tools/, slightly modify the s390 asm/bpf_perf_event.h
to include the local ptrace.h header file.
See also discussion on
https://marc.info/?l=linux-s390&m=151359424420691&w=2
Please note that this needs to be preserved until tools/ is able to
correctly handle asm specific headers.
References: https://marc.info/?l=linux-s390&m=151359424420691&w=2
Fixes: 720f228e8d31 ("bpf: fix broken BPF selftest build")
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Pull MTD fixes from Richard Weinberger:
"This contains the following regression fixes:
- fix bitflip handling in brcmnand and gpmi nand drivers
- revert a bad device tree binding for spi-nor
- fix a copy&paste error in gpio-nand driver
- fix a too strict length check in mtd core"
* tag 'for-linus-20171218' of git://git.infradead.org/linux-mtd:
mtd: Fix mtd_check_oob_ops()
mtd: nand: gpio: Fix ALE gpio configuration
mtd: nand: brcmnand: Zero bitflip is not an error
mtd: nand: gpmi: Fix failure when a erased page has a bitflip at BBM
Revert "dt-bindings: mtd: add sst25wf040b and en25s64 to sip-nor list"
|
|
Commit caa4b02476e3(blk-map: call blk_queue_bounce from blk_rq_append_bio)
moves blk_queue_bounce() into blk_rq_append_bio(), but don't consider
the fact that the bounced bio becomes invisible to caller since the
parameter type is 'struct bio *'. Make it a pointer to a pointer to
a bio, so the caller sees the right bio also after a bounce.
Fixes: caa4b02476e3 ("blk-map: call blk_queue_bounce from blk_rq_append_bio")
Cc: Christoph Hellwig <hch@lst.de>
Reported-by: Michele Ballabio <barra_cuda@katamail.com>
(handling failure of blk_rq_append_bio(), only call bio_get() after
blk_rq_append_bio() returns OK)
Tested-by: Michele Ballabio <barra_cuda@katamail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
